LOREX Technology LDC6051 User's Manual
Contents
1. moving while installing the dome cover Ceiling Camera Base Ball Camera Dome Cover Connecting The Camera To Camera To Monitor DVR Female power Oe ne Connect the BNC connector to the video input of the monitor DVR and connect the included power connector to a power adapter See Setup Diagram below for details Male power aS BNC Connect the BNC and power connectors to the camera BNC to RCA Adapter DVR CCTV MONITOR lt e i j Foa Video IN 0 Video IN ea BNC to RCA Adapter Attach the included BNC to RCA adapter to connect the extension cable to RCA inputs i e for a TV connection Setup Diagram Power 1 DVR Monitor Pa Power 2 Power oo G Extension Cable C 2388 iii Video input Cable Extension Options Extend the cable run for your camera up to 300ft or more depending on the cable type used See table below Max Cable Max of Run Distance Extensions BNC supplied with 180ft 55m camera Option Cable Type RG59 or Coax or Coaxial 300ft 92m BNC sold separately Lorex Universal Cable 300ft 92m sold separately Notes 1 For optimal performance consider using option 2 or 3 It is best to use the same cable type for the entire distance 2 Cable run recommendation based on typical camera power consumption up to 500mA For specialty cameras with higher current consumpti2. Contents Camera Specifications Weatherproof IR dome camera Image Sensor 1 3 Sony Super HAD II Mounting screws x 4 ee ee Teas Tey SUPER RESOLUTION WEATHERPROOF BNC female RCA male adapter oe NIGHT VISION DOME CAMERA enst menin V QUICK START GUIDE Sync System English Version 1 0 E E HH HE HE HH HE EE HE HE HE EE EE EE AES Shu er S eed Features ap Min Illumination 0 2 Lux without IR LED e Advanced Sony Super HAD II image sensor O Lux with IR LED e Video image processor produces sharp and clear video at 200 TV lines of resolution Video Output Composite 1 0Vpp 75ohm e Night vision up to 50f 15m away in total darkness Lens Lens Type 3 6mm F2 0 Fixed e ClearNight imaging technology ensures clear night vision and improves recording efficiency up to 30 FOV Diagonal ii e 3 6mm wide angle lens for wide area coverage 80 FOV Termination ee housing for indoor outdoor IR LED Gly Type Disclaimers Night Vision Range Infrared lamination range under teal conditons Actual range and clay may vay depending on Power Requirement ee ener ia E Power Consumption Oe ee ee a a ae ae ee ee E Operating Temp Range Wa rning Caution Operating Humidity Range lt 90 RH Methane ee a e Use the camera within given temperature humidity and voltage levels noted in Camera Specifications IR Illumination Range under ideal conditions Objects at or beyond this range may be partially or completely obscured
3. Options Bright spot in video e Night vision reflects when pointing a camera to when viewing camera a window Move the camera to a different at night location BNC connection does e Use a BNC to RCA adapter at the end of the not connect to my TV extension cable
4. depending on the camera application e Do not disassemble the camera Not intended for submersion in water Installation in a sheltered location recommended e Do not point the camera directly towards the sun or a source of VIEW YOUR WORLD WARNING A REGULATED UL CSA APPROVED power supply is REQUIRED for use with this camera Use of a non regulated non conforming power supply can damage this product and voids the warranty e Use only the supplied regulated power supply Use of a non Dimensions regulated non conforming power supply can damage this 95mm 3 8 product and voids the warranty Je e The supplied extension cable is rated for surface mounting only VIN e Cables for in wall floor to floor installations are sold 88mm 3 5 separately Installation Tips e Point the camera where there is the least amount of obstructions FOR SUPPORT AND INFORMATION i e tree branches VISIT WWW LOREXTECHNOLOGY COM e Install the camera in a location that is difficult for vandals to VANTAGE reach Product Information Specification Sheets e Secure cabling so that it is not exposed or easily cut Y pC 6051 e Camera rated for outdoor use Installation in a sheltered pave ser anal E Software Upgrades LDC6O5 l location recommended Quick Start Guides vu Firmware Upgrades Copyright 2011 Lorex Technologies Inc As our products are subject to continuous improvement Lorex reserves the right to modify product des
5. ign specifications and prices without notice and without incurring any obligation E amp OE Installing The Camera ATTENTION Test all connections and ensure the camera is working correctly prior to permanent installation by temporarily connecting the camera s and cable s to the viewing recording solution Before installing the camera e Decide whether to run the cables through the wall ao ceiling drilling required or along the wall ceiling e If you run the cables along the wall ceiling you must run the cable through the cable notch on the base This will keep the camera base flush to the wall ceiling when mounted yo Cable notch To install the camera 1 Rotate the camera base counterclockwise to separate it from the ball camera and dome cover 2 Feed the BNC power cable through the camera base If you are running the cables against a wall or ceiling make sure to pass the cable through the cable notch as shown above 3 Connect the video and power cable as shown in the next section Connecting The Camera 4 Mount the camera base to the wall or ceiling using the included screws 5 Position the dome cover over the camera and screw it clockwise halfway onto the camera base 6 Move the ball camera to the desired position While holding the ball camera firmly in place screw the dome cover the rest of the way to secure it to the camera base Holding the camera prevents it from
6. on maximum cable run may be reduced Consider providing power to the camera at the camera side rather then at the end of the extension cable 3 Indicators that your cable run may be too long e Video is permanently black amp white even during day time e Video is distorted Troubleshooting Problem Solution No Picture Signal Ensure your TV is on the correct input channel Common terms of an input Aa INPUT AV CHANNEL LINE1 LINE2 AUX If your camera is connected to a VCR DVR ensure it is properly connected to your TV Monitor Ensure connections are properly connected Ensure the camera power Aine is plugged in Ensure your camera isn t pointed directly at a source of light e g sun or spot light Slide the sunshade bullet cameras only forward to block excess light Move your camera to a different location Picture is too bright Picture is too dark If using during the day the camera may not be getting ance light Slide the sunshade bullet cameras only backwards to let more light in Check the brightness and contrast settings of the device your camera connects to TV Monitor DVR Night vision is not e The night vision activates when light levels working drop The area may have too much light Picture is not clear e Check the camera lens for dust dirt and ee Clean the lens with a soft clean cloth e Make sure that the cable run is within the limitations specified in the section Cable Extension
Download Pdf Manuals
Related Search