Linak TWINDRIVE TD1 User's Manual
Contents
1. Option Colour Emerg lowering Channels Angle footrest Angle headrest Transformer Number of motors Type Twist bracket 0 Straight 3 2 m EU wall plug 3 Straight 3 2 m UK wall plug 4 Straight 3 2 m Japanese wall plug 5 Straight 3 2 m US wall plug 7 Straight 3 2 m AUS wall plug 9 Used together with ext mains cut off 0 Standard 0 None 1 Mains cut off with EU wall plug black without non detachable cable 3 2 m 2 Internal mains cut off 0 230V 1 120V 2 100 V 0 None A Prepared for IR connection B Prepared for memory and infrared A Standard grey RAL 7035 B black 0 None 1 Emergency lowering via 9V battery Incl batteries 2 Emergency lowering via 9V battery Excel batteries 0 None standard only with memory and infrared 0 Standard 45 degrees 0 Standard 68 degrees 0 Toroidal transformer 0 Standard 1 Only 1 motor for headrest 1 T1D 1 To be ordered separately Chapter 16 1 Copyright LINAK 05 10 MA M9 02 088 E2. PRODUCT DATA SHEET TWINDRIVE HOMELNE TD1 Features Options Angle footrest 45 3 Angle headrest 68 3 Compatible with HB10 and HB20 EOP in TD1 280 version Toroidal Transformer in TD1 280 and El core Transformer in TD1 220 Duty cycle 10 6 min per hour max 2 min continuous use followed by 18 min not in use Max speed 0 58 RPM with max torque Installation dimension 796 mm length x 90 mm height x 90 mm width Installation dimension on the shaft 581 1mm Colour Grey plastic on motor housing RAL 7035 closing device Grey RAL 7016 Ambient temperature 5 C to 40 C Storage and transport temperature 10 C to 70 C Approved according to EN 60335 1 EMC according to EN55014 1 EN55014 2 Low built in height Low noise level Emergency lowering 2 x 9V batteries External Mains cut off Internal mains cut off only TD1 220 1 extra channels for an extra motor analogue systems Up to 2 extra channels for extra motors only TD1 280 with memory and Infrared Memory only TD1 280 Memory and Infrared only TD1 280 Black growing demands for motorised sy leisure bed area TD1 is characterised by the very low built in height which makes it unique in this market and gives much more free height under the bed than previous systems for e g storage or easy cleaning access LINAK 5 WE IMPROVE YOUR LIFE Dimension mm Compatible actuators Ac
3. ets HB20 HB20 HB20 Analogue 00 Memory B1 Memory C1 Receiver Transmitter TWINDRIVE TD1 220 Ordering example Mi1010000A0000 0 Cable 0 Straight 3 2 m EU wall plug 3 Straight 3 2 m UK wall plug 7 Straight 3 2 m AUS wall plug 9 Used together with ext mains cut off IP degree 0 Standard Mains cut off 0 None 1 Mains cut off with EU wall plug black without non detachable cable 3 2 m 2 Internal mains cut off Mains voltage 0 230 V Option 0 None Colour A Standard grey RAL 7035 B black Emerg lowering 0 None 1 Emergency lowering via 9V battery Incl batteries 2 Emergency lowering via 9V battery Excl Batteries Channel 0 None Angle footrest 0 Standard 45 degrees Angle headrest 0 Standard 68 degrees Transformer 1 El core transformer version Number of motors 0 Standard 1 Only 1 motor for headrest Type 1 TD1 Twist bracket To be ordered separately TWINDRIVE TD1 280 Ordering example M1000000A0000 0 L Specifications subject to change without prior notice It is the responsibility of the product user to determine the suitability of LINAK A S products for a specific application LINAK will at point of delivery replace repair defective products covered by the warranty if promptly returned to the factory No liability is assumed beyond such replacement repair Cable IP degree Mains cut off Mains voltage
4. t the mounting brackets are in place before TD1 is used If the TD1 unit is mounted in the bed it will not be able to fall out if it is under load because the spindle nut is designed to hold it in place Dimensions axle distance 581 25 SCALE 3 5 502 Mounting instructions welding For the TD1 it is important that one does not weld on the outside of the Twist Bracket because there is not room for a welding seam in the motor housing One may weld the bracket along the whole length of its ends Welding diagram To maintain the correct angle of rotation of the head rest and the foot rest it is important that the Twist bracket is welded according to the above instructions Non compliance with the instructions could lead to a smaller angle of rotation or in a worst case damage to TD1 90 for max stroke No welding on outside Dimensions drawing of the twist bracket LINAK part number 0701030 I2 195 7 35 Initialisation of the TD1 memory and infrared system To ensure optimum drive of the systems with memory infrared and extra channels must be run out to the outward position and in again before use This drive out in must be done without stops ul Removal fitting of the 9V batteries Changing of the 9V batteries is possible by pushing the batteries upwards via the two holes in the bottom of the unit It is necessary to use a blunt instrumen
5. t with a diameter of 06 mm When the batteries are visible from above they can be removed by using fingers Important before removal remove the battery clips Fitting is done by pushing the batteries into the holes remembering that the clips must be uppermost and that they are first connected when the batteries are in place If the battery option is chosen the system will be able to be lowered into the reset position by using the reset button on the handset during power failure This function is only available for the head and foot rest and only when the emergency lowering function is an available option Speed diagram Torque on testrig for Twindrive 220 Nm 280 Nm 300 250 200 Torque Nm gt on O O Ql O 0 10 20 30 40 50 60 70 Degrees above horisontal J Maximum torque occurs with a non linear load as prevails under use in a leisure bed That is to say large torque during start which lessens as the backrest is raised This is also how the TD1 has been tested Speed curve for the TD1 analogue versions TWINDRIVE 1 Speed 0 90 0 80 0 70 2 ep Speed Rpm Oo O1 O 0 00 18 72 126 180 234 288 Torque Nm 220 Nm 3500 N 280 Nm 4500 N Technical specifications Spindle Torsion Speed at Duty cycle pitch full load mm Rpm TD1 220 TD1 280 The above measurements are made in connection with internal control box and are average values Compability with standard hands
6. tuators that are compatible with TD1 LA27 LA31 A LG LA31 with fast motor cannot be used in combination with TD1 Always choose LA27 and LA31 without brake otherwise there will it not be enough power in the 2 x 9 Volt batteries Tk for emergency lowering In some cases where a standard HB is to run head foot motor and the external actuator simultaneous down it can happen that the actuator not will start if a brake is mounted In the TD1 280 system with memory and infrared the current cut off down is not sufficient to start up the extra actuator if a brake is chosen Cable for LA27 The cable used together with LA27 has to ordered separately LA27 0705816 a ii AWUN Lh EEEE ooo H waer 2004 30 125420 10020 Cable for LA31 The cable used in combination with LA31 is not possible to choose in the respectable ordering examples for the actuator To avoid any confusing write X when stating the cable and specify the cable as 0705825 LA31 ee A 0705825 200 30 125 20 200425 60 5 Mounting instructions Mounting instructions for TWINDRIVE Before mounting both mounting brackets must be pulled out to their outer position by pushing them back This gives freedom of movement to the bed bracket Mounting is done by pushing the bed bracket into the TD1 unit and thereafter pushing the mounting brackets back again IMPORTANT one must be completely sure tha
Download Pdf Manuals
Related Search