Lightolier IS-SQ6_Flange User's Manual
Contents
1. 0 1 4 4 16 Run ko Step 2 Installing the First Fixture A Remove the knockout on the top of the fixture B Attach the end trim plate to the end of the fixture that will rest against the end of the opening Fig 1 C Lift the fixture to the ceiling and run the wires through the knockout and attach the conduit to the fixture Then make electrical connections per NEC amp local codes Fig 2 Fixture Q Screws End Trim Plate Figure 1 Lightolier is a Philips group brand Figure 2 631 Airport Road Fall River MA 02720 e 508 679 8131 e Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group B0608 PHILIPS LIGHTOLIER Lighting Systems IS SO6_Flange Page 3 of 3 Instruction Sheet for Assembly and Installation of SQ6 Flange D Insert the fixture into the opening making sure that the flange rest flush with the ceiling and that the edge of the fixture is against the end of the opening Insert the fixture support brackets into the slots on the inside of the fixture Fig 3 While holding the fixture flush to the ceiling slide the support bracket down until it hits the ceiling Fig 3 Tighten the support bracket screw to hold it in place Fig 4 Install the remaining support brackets the same way x amm Slot NS KO Push Down Ceiling i Fixture Support Bracket Figure 3 Fi2. LIGHTOLIER Lighting Systems IS SQ6_Flange Page 1 of 3 Instruction Sheet for Assembly and Installation of SQ6 Flange READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE PROCEEDING RETAIN THESE INSTRUCTIONS FOR MAINTENANCE REFERENCE This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before installation To prevent electrical shock turn off electricity at electrical panel before proceeding DO NOT INSTALL THIS SYSTEM IN A WET OR DAMP LOCATION DO NOT ENERGIZE ANYTHING OTHER THAN THE FIXTURES IN THE SYSTEM CONTRACTOR IS RESPONSIBLE FOR ADEQUATELY REINFORCING CEILING TO SUPPORT FIXTURE WEIGHT j 478 __ 47 8 5 3 4 5 3 4 631 Airport Road Fall River MA 02720 e 508 679 8131 e Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group B0608 Lightolier is a Philips group brand PHILIPS LIGHTOLIER Page 2 of 3 Step 1 Cutting Out the Opening for the Fixtures Cut out the opening for the desired run length Lighting Systems IS SO6_ Flange Instruction Sheet for Assembly and Installation of SQ6 Flange Ceiling Cut Out Size 4 0 1 4 5 4 Run 8 0 1 4 Be 8 Run H 16
3. gure 4 Step 3 Installing the Remaining Fixtures A Lift the next fixture into the opening and hold it flush with the ceiling and against the previous fixture B Once the fixture is mounted connect wiring to the previous fixture by removing the reflector to access the wires in the ballast tray C Install the fixture support brackets as done with the first fixture D Insert and tighten the joining screws through the clearance holes on one fixture and into the riv nuts on the other fixture Fig 5 Figure 5 Step 4 Installing the Last Fixture A On the last fixture in the run attach the remaining end trim plate to the end of the fixture that will rest against the end of the cut out Fig 1 B Install the fixture the same as the others C Once all of the fixtures have been installed re attach the reflectors lamp the fixture and install the louvers 631 Airport Road Fall River MA 02720 e 508 679 8131 e Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group B0608 Lightolier is a Philips group brand PHILIPS
Download Pdf Manuals
Related Search