Lightolier IS:LLACSW User's Manual
Contents
1. Fig 9 For wall mount Mount 2 anchors 15 in 381mm apart Fig 12 Determine light beam orientation uplight or downlight Fig 3a amp 3b Loosen screw from the mounting tabs Fig 10 amp 11 Rotate and position oblong holes located at each end Fig 11 Locate embossed holes and screw in place Fig 10 amp 11 Install screws not provided through oblong holes Fig 8 amp 9 D OT oN FLOOR INSTALLATION m amp or at each end Fig 10 amp 11 2 Loosen screw from the mounting tabs Fig 10 amp 11 3 For more stability depending on optical assembly orientation secure with 2 screws from each end of assembly optional Fig 9 amp 12 4 Locate embossed holes and screw in place Fig 10 amp 11 5 Install screws through oblong holes Fig 12 Lightolier is a Philips group brand Position mounting tabs towards front of the luminaire for stable floor standing Wall Floor Daisy Chain FIG 3b FIG 4 FIG 5 sine HEAD ON LOCKING C H C SCREW oe x a a aaa FIG 6 FIG 7 ALLAN KEY 20 12 S21 nn ANCHOR SSP Ad A a EE L n ae d LUMINAIRE S i i FIG 8 LUMINAIRE EMBOSSED 2 21mm SCREW MOUNTING TAB FIG 10 SCREW MOUNTING TAB FIG 11 PHILIPS LIGHTOLIER Page 2 of 2 E DAISY CHAIN INSTALLATION Fig 13 Note Use 3 8 in flexible metal conduit only 1 Remove connection cover plate 2 Loosen bushing and cord 3 Remove2. LIGHTOLIER Page 1 of 2 IS LLACSW 10 08 Rev 01 Installation Instructions for Surface LED Colorwash Luminaire CAUTION Please read these instructions before installing the luminaire To avoid electric shock turn off the power from the electric panel before beginning For safety this luminaire must be grounded Consult an electrician to make sure all the requirements of the US or Canadian Code for electricity and the current local regulations comply Keep these instructions as reference Note 1 This portable luminaire Fig 1 uses LED light emitting diode lamps which require no maintenance Designed for residential commercial and industrial applications non hazardous dry locations ceiling Fig 2 wall mounted Fig 3 and floor applications Fig 4 Note 2 This portable luminaire includes a 96 in extension cord and can also be hardwired using flexible metal conduit Fig 5 two 3 8 in connectors are supplied Portatif ColorWash Ceiling FIG 1 FIG 2 A OPTICAL ASSEMBLY ADJUSTMENT 1 Adjust head on assembly at the desired angle Fig 6 2 Lock in place inserting ocking screws through hinge Fig 7 Note Use a 3 16 in Allen key not supplied B CEILING or WALL MOUNT INSTALLATION Fig 2 Note Provide anchors to support 8 Ib 3 6kg luminaire For ceiling mount 1 Install 2 anchors at 20 1 2 in 520mm from uminaire center Fig 8 Note For more stability install 4 anchors 2 in from center of the luminaire
3. capacitance shielded twisted pair stranded cables such as EIA485 RS485 or shielded CAT 5e 24AWG maximum run length of 300 m 1000 ft 22AWG maximum run length of 500 m 1600 ft Note Using unshielded cable may create noise in the system and may cause undesirable light output Connectors RJ45e connector 8 conductors connections T5688 Lightolier is a Philips group brand IS LLACSW 10 08 Rev 01 15 38mm SCREW OBLONG HOLES ANCHOR COVER PLATE SCREW CORD i BUSHING S FIG 13 FIG 14 FIG 15 FIG 16 TERMINATOR FIG 17 PHILIPS
4. knock out from the arge hole Note For continuous daisy chain other knock out and cord must be removed Insert red sleeve on BX cable Snap 3 8 in connector into cover plate hole s Connect the green wires to ground the fixture Connect the white NEUTRAL wires together Connect the black 120V wires together Reinstall cover plate with 2 screws F 4 BUTTON CONTROLLER Note Control buttons display are touch sensitive Touch centre of pictogram A audible beep confirms new selection PRESET A Fig 14 a One touch selection changes preset up A or dowr b Hold any selection to scroll between presets in a continuous loop hold preset 7 Note For more details on PRESET see PRESET sheet BRIGHTNESS 4 lt Fig 14 a One touch selection increases reduces brightness level by 5 b Hold setting to dim up down in 5 increments every 1 5 second G FOR DMX CONTROL 1 Simply connect data cable shielded cats recommended into DMX connector RJ45e jack Fig 15 2 For daisy chain data connection connect data cable cat into data in socket of the first luminaire then connect the data cable to the data out connector jack of the next luminaire and so on Fig 16 3 For signal termination connect a DMX signal terminator to the data out of the last luminaire in the network sold separately Fig 17 Note Hardware required for DMX control system not supplied Controller DMX512 protocol Wiring Use low
Download Pdf Manuals
Related Search