Lightolier Fluorescent Downlight and Wall Washer User's Manual
Contents
1. over LENS TRIM as shown in Fig 2 and 3 2 For flangeless trim installation Fig 4 WHITE TRIM RING is not required PUSH UP REFLECTOR FOR LENS WALL WASHER 1 Tilt REFLECTOR and insert SOCKET CUP into ceiling opening on side opposite JUNCTION BOX Push REFLECTOR up leaving approximately one inch of the REFLECTOR exposed below the CEILING LINE Fig 10A 2 Compress TORSIONTITE SPRINGS on LENS TRIM by squeezing with fingers Insert into SLOTS in REFLECTOR and push up into REFLECTOR until flush with ceiling Fig 11 NOTE To remove REFLECTOR lift LENS and pull LENS TRIM down Fig 12 then disengage the SOCKET CUP by depressing the RETAINING SPRING Fig 5 Turn REFLECTOR counterclockwise while pulling downward After starting use both hands to remove See Fig 7 PUSH UP REFLECTOR FOR OPEN WALL WASHER 1 Tilt REFLECTOR and insert SOCKET CUP into ceiling opening on side opposite JUNCTION BOX Pivot REFLECTOR and push it up into ceiling Fig 13 NOTE To remove REFLECTOR disengage the SOCKET CUP by depressing the RETAINING SPRING Fig 5 Turn REFLECTOR counterclockwise while pulling downward After starting use both hands to remove If desired See Fig 7 LAMPING Line up pins and push into socket To relamp carefully pull lamp straight out CARE AND MAINTENANCE OF ALZAK REFLECTOR If handling of reflectors with anodized or Alzak finish is required the use of clean white or plastic film gloves is recommene2. starting use both hands to remove If desired See Fig 7 D LAMPING Insert lamp tip first through hole in side of reflector opposite lamp SOCKETS Bring lamp to horizontal position line up pins and push into socket Fig To relamp carefully pull straight out of socket tilt base downward and remove lamp FIG 4 INSTALLATION OF LENS WALL WASHER AND OPEN WALL WASHER RETAINING NOTE Before installing reflector make sure the mounting frame is SPRING Installed with JUNCTION BOX away from the wall to be illuminated SOCKET i Fig 10A or 10B CUP TABS aaa FOR OPEN WALL WASHER 1 Remove two RETAINING SPRINGS that are near the JUNCTION BOX from FIG 5 the MOUNTING FRAME Fig 9 2 Insert two new RETAINING SPRINGS that are provided with the reflector TO REMOVE trim into pocket of MOUNTING FRAME Fig 9A Sue JUNCTION 3 Then squeeze RETAINING SPRING into position with a plier Fig 9A BOX REFLECTOR En l FIG 6 FIG 7 RETAINING SPRING REMOVED MOUNTING FRAME SECAUCUS NEW JERSEY 07096 MONTREAL QUEBEC CANADA LIigskiTOLilzl A INSTALLATION OF COMPACT FLUORESCENT DOWNLIGHTS AND WALL WASHERS CONT D SNAP IN Align TABS on SOCKET CUP with openings in reflector and push in SOCKET CUP until RETAINING SPRING snaps in Fig 5 INSTALL WHITE TRIM RING NOTE Omit this section If reflector is self flanged 1 For overlapping trim installation Fig 1 slip WHITE RING
3. INSTRUCTION SHEET NO INSTALLATION OF COMPACT FLUORESCENT DOWNLIGHTS AND WALL WASHERS IS 8 0 54 C L 0891 Page 1 of 2 READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before installation To prevent electrical shock turn off electricity at fuse box before proceeding This fixture is intended for ceiling mounting and is suitable for damp locations Retain these Instructions for maintenance reference INSTALLATION OF DOWNLIGHT A INSTALL WHITE TRIM RING NOTE Omit this section If reflector is self flanged 1 For overlapping trim installation Fig 1 slip WHITE TRIM RING over REFLE R as shown in Fig 2 and 3 2 For flangeless trim installation Fig 4 WHITE TRIM RING is not FIG 1 required B SNAP IN WHITE Align TABS on SOCKET CUP with openings in REFLECTOR and TRIM push in SOCKET CUP until RETAINING SPRING snaps in Fig 5 RING C PUSH UP REFLECTOR ne 1 Tilt REFLECTOR and insert SOCKET CUP into ceiling opening on K D side opposite JUNCTION BOX Pivot REFLECTOR and push it up REFLECTOR d into ceiling Fig 6 OR LENS TRIM NOTE To remove REFLECTOR disengage the SOCKET CUP by FIG 2 FIG 3 depressing the RETAINING SPRING Fig 5 Turn REFLECTOR counterclockwise while pulling downward After
4. ded to avoid fingerprints Anodized or Alzak surfaces can be cleaned by the following methods 1 Wipe off with a soft clean dry lint free cloth 2 Wipe off with a soft clean cloth dampened in mild detergent solution Rinse then wipe dry with lint free cloth or paper towel 3 Wipe off with a clean cloth dampened with a solution of wetting agent and water such as 2 oz per gallon Pluronic L62 LF by Wyandotte Products Then wipe dry 4 Or use a liquid wash such as Glass Wax Avoid gritty cleaning agents JUNCTION BOX SOCKET CUP IS 8054CL 0291 Page 2 of 2 LENS WALL WASHER SOCKET CUP ANTON BOX REFLECTOR P LEAVE APPROX J 1 EXPOSED iy T A TORSIONTITE PRING LENS TRIM WALL TO BE ILLUMINATED FIG 10A OPEN WALL WASHER JUNCTION BOX WALL TO BE ILLUMINATED FIG 10B FIG 11 FIG 12
Download Pdf Manuals
Related Search