Lightolier Calculite IS-PS User's Manual
Contents
1. 008 Philips Group B0908 Lightolier is a Philips group brand PHILIPS LIGHTOLIER Calculite IS PS Page 3 of 7 Instruction Sheet for Assembly and Installation of ProSpec Linear Series S FRAME IN AND WIRE Step 1 Install Housing using Adjustable Mounting Brackets A Fixture must be secured to structural ceiling members If no ceiling access available fixtures must be installed before ceiling material With Mounting Bar Lightolier Cat No 1951 use rectangular slots Fig 1 With 1 2 1 27cm EMT by others Fig 2 _ With 3 4 1 91cm or 1 1 2 3 81cm Channel by others Fig 3 For Suspended T Bar Ceilings use Lightolier Cat No 1956 to secure 1951 Mounting Bars to ceiling runners Fig 4 F To install with hanging wires by others consult installation from hanging wire manufacturer Adjustable Mounting Bracket m Oo W ae Mounting Bar 1 2 1 27cm Order Separately 1951 EMT By Others 3 4 1 91cm or Screw Screw Screw 1 1 2 3 81cm Channel By Others Figure 1 Figure 2 Figure 3 Anchor Cli Mounting Bar Order e 1956 Order Separately 1951 A a Figure 4 Step 2 Connect Supply Leads White fixture lead to neutral white supply black fixture lead to hot supply lead bare fixture wire to supply ground Use wire nuts for all connections local hardware items Step 3 Place all electrical connections in J Box attached to side of fixture Step 4 Attach J Bo2. LIGHTOLIER Calculite IS PS Page 1 of 7 Instruction Sheet for Assembly and Installation of ProSpec Linear Series S READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE PROCEEDING RETAIN THESE INSTRUCTIONS FOR MAINTENANCE REFERENCE This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before installation To prevent electrical shock turn off electricity at electrical panel before proceeding DO NOT INSTALL THIS SYSTEM IN A WET LOCATION CONTRACTOR IS RESPONSIBLE FOR ADEQUATELY REINFORCING CEILING TO SUPPORT FIXTURE WEIGHT Adjustable Mounting Bracket Housing sn Housing Aperture Opening __ Inside Dimension m s Flanged Trinless 631 Airport Road Fall River MA 02720 e 508 679 8131 e Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group B0908 Lightolier is a Philips group brand PHILIPS LIGHTOLIER Calculite IS PS Page 2 of 7 Instruction Sheet for Assembly and Installation of ProSpec Linear Series S Warning for All Fixtures Use only aperture frames and accessories provided by Lightolier Inc Use of other manufacturers a
3. e Ring Aperture Housing Opening Electrical Ratings Length Width Input Amps PS1M16 5 12 70cm 5 12 70cm 15 Cat No PS2M16 10 25 40cm 5 12 70cm ine PS3M16 15 38 10cm 5 12 70cm 2 25 PS4M16 20 50 80cm 5 12 70cm CAUTION Turn power off before lamping fixture Wait until fixture is cool before touching 631 Airport Road Fall River MA 02720 508 679 8131 Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group B0908 Lightolier is a Philips group brand PHILIPS LIGHTOLIER Calculite IS PS Page 7 of 7 Instruction Sheet for Assembly and Installation of ProSpec Linear Series S ADJUSTING AND LOCKING OF AIMING ANGLE Insert 7 64 allen key into cap screw and turn counter clockwise to unlock head and gimbel ring assembly Aim beam angle of lamp towards desired direction and turn cap screw clockwise to lock Head and gimbel ring assembly Widthwise Locking Insert allen key into opening of lever and gently move allen key in a counter clockwise arc to unlock lengthwise aiming direction Aim beam angle towards desired direction and gently move lever in clockwise direction to lock aiming angle Lengthwise Locking 631 Airport Road Fall River MA 02720 e 508 679 8131 Fax 508 674 4710 We reserve the right to change details of design materials and finish www ligh
4. perture frames and accessories voids the Underwriters Laboratories Listing and could constitute a fire hazard Caution Risk of Fire Use proper lamp wattages with corresponding ballast wattages Check ballast module wattage label to confirm wattage Caution Risk of Burn Allow time for luminaire to cool before attempting to relamp or position Caution Risk of Burn and Electrical Shock Turn off power to Ballast Module before servicing All PowerArc Modular Ballasts are equipped with a power switch Depressing Dot on Switch is the ON position See IS 83B Note 1 Low voltage fixtures may produce audible sound when used with dimmers which maybe objectionable in acoustically critical areas 2 For HID Fixtures HID lamps require a warm up period of 5 10 minutes to reach full output Additionally when these lamps are extinguished they must cool for 5 15 minutes before they will relight Outage can be caused by momentary power failure substantial voltage reduction or cycle changes Warning for MR16 Fixtures Only Lamp manufacturers require the glass lamp guard be in place before energizing lamp and that great care must be taken that lamp is fully cooled before relamping Avoid finger marks on inside of lamp for they may cause short lamp life and possible breakage 631 Airport Road Fall River MA 02720 508 679 8131 Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2
5. s and finish www lightolier com 2008 Philips Group B0908 Lightolier is a Philips group brand PHILIPS LIGHTOLIER Calculite IS PS Page 5 of 7 Instruction Sheet for Assembly and Installation of ProSpec Linear Series S INSTALL APERTURE FRAME Step 1 Aperture Frame Installation A MR16 a Insert Plug Connectors from sockets into receptacles on inside wall of housing b Connectors are polarized and therefore may only be inserted in one direction c Make sure connectors snap firmly into space Fig 9 Step 2 A Hook tortiontite Springs into slots of housing B Push Aperture Frame upward Fig 10 SKT MountingScrew Receptacle Connector Housing Tortiontite Springs Housing Slot a socket S A Plug Connector Apperture Frame MR16 Figure 9 Figure 10 631 Airport Road Fall River MA 02720 508 679 8131 Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group B0908 Lightolier is a Philips group brand PHILIPS LIGHTOLIEI Calculite IS PS Page 6 of 7 Instruction Sheet for Assembly and Installation of ProSpec Linear Series S INSTALL LAMP AND ACCESSORIES Step 1 Remove Media Cartridge with counter clockwise motion Step 2 Install Lamp A Any combination of two accessories may be used to install into media cartridge and secure with spring B One accessory must be glass C Install Media Cartridge onto Adjustabl
6. tolier com 2008 Philips Group B0908 Lightolier is a Philips group brand PHILIPS
7. x Cover onto J Box attached to side of fixture 631 Airport Road Fall River MA 02720 508 679 8131 e Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group B0908 Lightolier is a Philips group brand PHILIPS LIGHTOLIER Calculite IS PS Page 4 of 7 Instruction Sheet for Assembly and Installation of ProSpec Linear Series S ADJUST HOUSING Flanged Aperture Frame Adjust Housing at Mounting Brackets so that bottom edge is flush with finished ceiling as shown Fig 5 Trimless Aperture Frame A Adjust Housing so bottom edge is flush with or above Finished Ceiling Fig 6 B Insert Plaster Frame into Housing Aperture Opening and secure with 6 mounting screws while pushing Plaster Frame against ceiling Fig 7 C Screw Plaster Frame to ceiling and spackle to edge of plaster frame Fig 8 Housing Aperture Opening H Mounting Screw aniy iN ey Do a ee ee Seve hie joes oa es SAS deve Sep ro Dein Pe Bee TE eek s gt oy Se aero i Plaster Frame Figure 5 Figure 6 Figure 7 Finished Ceiling Finished Ceiling lrimless Aperture Frame l nee X Sheet Rock Spackle Figure 8 631 Airport Road Fall River MA 02720 e 508 679 8131 e Fax 508 674 4710 We reserve the right to change details of design material
Download Pdf Manuals
Related Search