Life Fitness LIFECYCLE R1 User's Manual
Contents
1. SNOTLONGdLSNI AIAWASSVY S4Ay1d ASIOYAXA 319494411 EU LY Lie Fares Life Fitness offers a Tull line of premier fitness equipment for the home TOTAL BODY ELLIPTICAL CROSS TRAINERS TREADMILLS LIFECYCLE EXERCISE BIKES STAIRCLIMBERS GYMSYSTEMS 5100N RIVERROAD SCHILLER PARK ILLINOIS 60176 LIFEFITNESS COM 2006 Life Fitness a division of Brunswick Corporation All rights reserved Life Fitness is a registered trademarks of Brunswick Corporation Any use of this trademark without the express written consent of Life Fitness is foroidden 8114701 Rev A 1 07 06 Item a DO oO FP WYN 8 9 10 11 12 13 14 15 16 17 18 19 Oty Description R18 R3 2 2 50 mm Button Head Screw 10 10 15 mm Button Head Screw Flat Washer 18 mm 0 D 55 mm Phillips Screw Lock Washer 12 2 mm O D 8 mm Phillips Screw 40 mm Button Head Screw with Locking Compound Flat Washer 24 mm 0 D Rubber Bumper Insert 1 Rubber Bumper 12 mm Phillips Screw with Locking Compound 12 mm Large Head Phillips Screw 100 mm Hex Head Bolt Thick Flat Washer 16 mm 0 D 60 mm Hex Head Bolt 12 mm Small Head Phillips Screw Flat Washer 12 mm 0 D 12 mm Self Tapping Screw 12mm Phillips Screw O wo o ol A 0 co Ol Sk o N S So O aA ANONA gt a Cc BH NM OF BR DO Assembly Guide Look for the number coded hardware bags that match the assembly sequence Physical Dimensions R1 Length Width Height Weight2. to the corresponding WIRE W from the SIDE ACCESS HOLE X of the MONOCOLUMN Slide the MONOCOLUMN COVER T downward to meet the MAIN SHROUDS Secure the MONOCOLUMN COVER to the MAIN SHROUDS using four 12 mm PHILLIPS SCREWS 16 Tighten the SCREWS securely Do not overtighten the SCREWS Attach the RIGHT BB and LEFT CC FRONT HANDLEBARS labeled right and left to the MONOCOLUMN as shown using two each 15 mm BUTTON HEAD SCREWS 2 Tighten the SCREWS securely Remove the DISPLAY CONSOLE DD from its shipping carton Position the DISPLAY CONSOLE above the DISPLAY CONSOLE BRACKET EE Connect the CONSOLE WIRE FF HEART RATE WIRE GG RED and GROUND WIRE HH GREEN to the corresponding JACKS located on the back of the DISPLAY CONSOLE Secure the DISPLAY CONSOLE to the DISPLAY CONSOLE BRACKET using four 12 mm PHILLIPS SCREWS 18 Tighten the SCREWS securely Do not overtighten the SCREWS Locate the RIGHT PEDAL JJ marked with an R and PEDAL STRAP KK marked with an R With the side of the PEDAL STRAP marked with an R facing upward slide the slotted end of the PEDAL STRAP through the left slot in the PEDAL Fasten one of the slots onto the tab located under the left slot of the PEDAL Bend the PEDAL STRAP upward and slide the remaining end of the PEDAL STRAP through the right slot in the PEDAL and into the strap adjustment clip The PEDAL STRAP should securely engage the strap adjustment clip Install the RIGHT PEDAL JJ to t
3. R3 Length Width Height Weight Tools Required Metric Wrench Set Metric Allen Wrench Set Phillips Screwdriver 56 5 inches 143 5 centimeters 25 75 inches 65 4 centimeters 54 inches 137 centimeters 147 pounds 67 kilograms 56 5 inches 143 5 centimeters 25 75 inches 65 4 centimeters 54 inches 137 centimeters 147 pounds 67 kilograms Hardware List 140 150 160 2 amp 3 Seat Assembly Assembly Sequence Locate and install the two LEVELER FEET A to the bottom of the REAR STABILIZER B With the bends facing rearward attach the REAR STABILIZER B to the BASE UNIT C using two 50 mm BUTTON HEAD SCREWS 1 from the top of the REAR STABILIZER BRACKET D and two 15 mm BUTTON HEAD SCREWS 2 from the front side of the REAR STABILIZER BRACKET Tighten the SCREWS securely Locate the HANDLEBAR ASSEMBLY E and the SEAT ASSEMBLY F With the handlebars facing upward and forward align the mounting holes of the HANDLEBAR ASSEMBLY with those in the SEAT ASSEMBLY Secure the HANDLEBAR ASSEMBLY to the SEAT ASSEMBLY using four 15 mm BUTTON HEAD SCREWS 2 and FLAT WASHERS 3 Tighten the SCREWS securely Connect the CONNECTOR G leading from the HANDLEBAR ASSEMBLY E with the CONNECTOR G leading from the SEAT ASSEMBLY F Be sure the connectors fully lock Locate the SEAT BOTTOM H Align the SEAT BOTTOM mounting holes with those in the LOWER SEAT SUPPORT TUBES J Secure the SEAT BOTTOM using fou
4. y Secure the SEAT BACK PAD Q to the UPPER SEAT SUPPORT TUBES R using four 55 mm PHILLIPS SCREWS 4 and LOCK WASHERS 5 Tighten the SCREWS securely o R3 Only Secure the SEAT BACK COVER JJ to the SEAT BACK PAD Q using four M8 x 1 0 PHILLIPS SCREWS 19 Tighten the SCREWS securely Locate the MONOCOLUMN S Slide the MONOCOLUMN COVER T onto the MONOCOLUMN as shown Slide the MONOCOLUMN COVER up to the FRONT HANDLEBAR POSTS U NOTE A zip tie has been included to keep the MONOCOLUMN COVER T from falling during assembly Untape the WIRE TIE V attached to the front of the MONOCOLUMN S Carefully pull the CONSOLE WIRE W through the SIDE ACCESS HOLE X of the MONOCOLUMN Feed the CONSOLE WIRE through the GROMMET Y as shown and Insert the GROMMET into the SIDE ACCESS HOLE R1 amp R3 Recumbent Bikes Slide the MONOCOLUMN S into the MONOCOLUMN BRACKET Z Slide the MONOCOLUMN down until it is fully seated Secure the MONOCOLUMN to the MONOCOLUMN BRACKET using two 100 mm HEX HEAD BOLTS 13 and three THICK FLAT WASHERS 14 as shown from the front side of the MONOCOLUMN and two 60 mm HEX HEAD BOLTS 15 and THICK FLAT WASHERS 14 from the user left side of the MONOCOLUMN BRACKET Tighten the BOLTS securely CAUTION Be careful not to pinch the WIRE s AA leading from the MONOCOLUMN BRACKET Z when inserting the MONOCOLUMN S into the MONOCOLUMN BRACKET Connect the WIRE s AA leading from the MONOCOLUMN BRACKET Z
5. he USER RIGHT CRANK ARM LL Repeat for the LEFT PEDAL marked with an L and PEDAL STRAP marked with an L NOTE The LEFT PEDAL has reverse threads NOTE Pedals need to be securely tightened or clicking may occur 7 R1 Only Locate the WATER BOTTLE BRACKET MM Secure the WATER BOTTLE BRACKET to the underside of the MONOCOLUMN S using two 12 mm PHILLIPS SCREWS 12 Tighten the SCREWS securely Insert the WATER BOTTLE NN into the WATER BOTTLE BRACKET Position the unit in the desired location for use The unit can be easily moved into place by lifting the rear of the unit and rolling it on the front rollers Level the unit before use Refer to the leveling instructions stated in the User Manual 1 4 4 5 6 Rear Stabilizer Monocolumn Wiring Pedals Cover amp Console 7 R1 Only Water Bottle amp Bracket
6. r 55 mm PHILLIPS SCREWS 4 and LOCK WASHERS 5 Tighten the SCREWS securely R3 Only Locate the ACCESSORY TRAY K Secure the ACCESSORY TRAY to the HANDLEBAR ASSEMBLY using four 8 mm PHILLIPS SCREWS 6 as shown Tighten the SCREWS securely Align the guide rollers located on the underside of the SEAT ASSEMBLY F with the SEAT EXTRUSION L Carefully guide the SEAT ASSEMBLY onto the SEAT EXTRUSION Slide the SEAT ASSEMBLY fully forward Connect the WIRE M leading from the user left side of the SEAT ASSEMBLY to the JACK located at the left front of the SEAT EXTRUSION Insert the WIRE M into the WIRE HARNESS N located next to the JACK NOTE The WIRE M JACK and WIRE HARNESS N are located on the user left side of the unit Items shown on the right for clarity In the hole located on the user right side of the SEAT EXTRUSION L behind the SEAT ASSEMBLY F install one 40 mm BUTTON HEAD SCREW W LOCKING COMPOUND 7 one 24 mm FLAT WASHER 8 one RUBBER BUMPER SLEEVE 9 one 1 RUBBER BUMPER 10 and one 18 mm FLAT WASHER 3 as shown Mount the SEAT ADJUSTMENT LEVER O to the user right side of the SEAT ASSEMBLY F using two 12 mm PHILLIPS SCREWS W LOCKING COMPOUND 11 Tighten the SCREWS securely NOTE Be sure to mount the SEAT ADJUSTMENT LEVER O with the adjustment knob facing upward as shown Locate the SEAT EXTRUSION ENDCAP P Secure the SEAT EXTRUSION ENDCAP to the SEAT EXTRUSION Q using two 12 mm PHILLIPS SCREWS 12
Download Pdf Manuals
Related Search