Life Fitness G5 User's Manual
Contents
1. Q REPEAT THE ABOVE PROCESS FOR THE REMAINING GUIDE CABLE 31 19 STEP 11 Assemble the MOUNTING SHEET 22 to the top of the FRONT UPRIGHT 1 using two M10 x 20mm SCREWS 48 and two 3 8 WASHERS 39 Tighten screws SECURELY Q Attach the TOP LEFT COVER 25 the TOP RIGHT COVER 24 and the TOP COVER 23 to the MOUNTING SHEET 22 using four M4 x 0 7 ZINC PHILLIPS PAN HEAD SCREWS 47 DO NOT OVERTIGHTEN SCREWS INTO PLASTIC PARTS 20 STEP 12 Referencing step 5 at the UPPER SWIVEL PULLEYS 2 push back on the QUICK CONNECT SLEEVE F at the end of each cable and attach the SHORT HANDLES 26 Repeat the process for attaching the ADJUSTABLE HANDLES 28 to the lower cable ends and the MEDIUM HAN DLES 27 to the middle cable ends NOTE THE HANDLE CONFIGURATION DEFINED WILL ACCOMMODATE MOST EXERCISES NOTE THE FOOT STRAP 33 IS TO BE ATTACHED TO ONE OF THE MID SECTION PULLEY CABLE ENDS FOR LEG EXTENSIONS AND TO ONE OF THE LOWER PULLEY CABLE ENDS FOR LEG CURL EXERCISES 21 MAINTENANCE Please note We recommend cleaning your product pads and frame on a regular basis using warm soapy water Touch up paint can be purchased from your Life Fitness cus tomer service representative at 800 351 3737 Inspect equipment before each use Tighten all loose connections and replace worn parts immediately Failure to do so may result in serious injury PLEASE RECORD THE INFORMATION REQUESTED BEL2. G5 CABLE MOTION GYM SYSTEM ASSEMBLY INSTRUCTIONS G5 001 CLASS H 04 07 10 8289201 REV C NX VV V TABLE OF CONTENTS Safety Statement 2 Hardware 8 G5 Warning Labels 4 Assembly Instructions 10 Gym Dimensions 5 General Maintenance 22 G5 Live Area 6 Warranty Statement Notes 23 Components List 7 Contact Information 24 SAFETY INFORMATION It is the sole responsibility of the purchaser of LIFE FITNESS products to read the owner s manual warning labels and instruct all individuals whether they are the end user or supervising personnel on proper usage of the equipment UNDERSTANDING EACH AND EVERY WARNING TO THE FULLEST IS IMPORTANT IF ANY OF THESE INSTRUC TIONS OR WARNINGS ARE UNCLEAR CONTACT LIFE FITNESS CUSTOMER SERVICE IMMEDIATELY AT 1 800 351 3737 WITHIN THE US AND CANADA INTERNATIONAL OFFICE CONTACT INFORMATION IS AVAILABLE ON PAGE 24 Keep children away from strength equipment Parent or others supervising children must provide close supervision of children if the equipment is used in the presence of children This equipment is categorized as class H per EN 957 1 And as such this equipment is only intended for Home use It is not intended for commercial institutional and or studio facilities use Contact LIFE FITNESS with any questi
3. 043 818 07 20 Switzerland Austria Life Fitness Austria Vertriebs G m b H Duckegasse 7 9 3 36 1220 Vienna AUSTRIA Telephone 43 1 61 57 198 Fax 43 1 61 57 198 20 Spain Life Fitness IBERIA C Frederic Mompou 5 1912 08960 Sant J ust Desvern Barcelona SPAIN Telephone 434 936 724 660 Fax 434 936 724 670 Italy Life Fitness ITALIA S R L Via Crivellin 7 N 37010 Affi Verona ITALY Telephone 439 045 7237811 Fax 439 045 7238197 Belgium Life Fitness Benelux NV Parc Industrial de Petit R echain 4800 Verviers BELGIUM Telephone 432 87 300 942 Fax 432 87 300 943 All Other EMEA countries amp distributor business C EMEA Bijdorpplein 25 31 2992 LB Barendrecht THE NETHERLANDS Telephone 431 180 646 666 Fax 431 180 646 699 Also check www lifefitness com for local representation or distributor dealer G5 001 Rev C 04 10 24 Asia PACIFIC AP Japan Life Fitness J apan Nippon Brunswick Bldg 8F 5 27 7 Sendagaya Shibuya Ku Tokyo 151 0051 Telephone 481 3 3359 4309 Fax 481 3 3359 4307 China and Hong Kong Life Fitness Asia Pacific LTD Room 2610 Miramar Tower 132 Nathan Road Tsimshatsui Kowloon HONG KONG Telephone 4852 2891 6677 Fax 4852 2575 6001 All Other Asia Pacific countries amp distributor business Asia Pacific Room 2610 Miramar Tower 132 Nathan Road Tsimshatsui Kowloon HONG KONG Telephone 4852 2891 6677 F
4. 7 Continue routing the cable as shown ending at the RIGHT MID PULLEY ASSEMBLY K Reattach the previously removed QUICK CONNECT to the end of the LOWER LONG CABLE 30 NOTE THE CABLE MUST BE INSERTED BETWEEN THE PULLEY AND THE PULLEY GUIDE L AND MOVE FREELY Repeat the routing on the left side of the unit using the remaining LOWER LONG CABLE 30 16 RE 2 Ze LE lt LV 5IC 8 Attach the BACK THIGH HOLD CLAMP 18 to the the FRONT UPRIGHT 1 using two M6 x 60mm SCREWS 51 and two 1 4 WASHERS 52 from the back of the FRONT UPRIGHT 1 0 Attach the THIGH HOLD DOWN 19 to the FRONT UPRIGHT 1 by using four M10 x 70mm SCREWS 41 eight 3 8 WASHERS 39 and four M10 HEX NYLOCK NUTS 53 through the FRONT SHROUD 15 and through the FRONT UPRIGHT 1 Tighten SECURELY STEP 9 Q Attach the TOP FRONT COVER 21 to the TOP BACK COVER 20 using eight M4 ZINC PHILLIPS HEAD SCREWS 54 DO NOT OVERTIGHTEN SCREWS INTO PLASTIC PARTS 18 STEP 10 Insert ball end of one GUIDE CABLE 31 through eye hook on one FLOATING PULLEYS 14 Insert and hook the ball end of the cable into the SLOTTED BUSHING N located at the bottom of the frame located directly below the FLOATING PULLEYS 14 Screw the threaded end of the cable into the FRONT UPRIGHT 1 and loosely tighten the cable by screwing the JAM NUT M to the top of the frame
5. DO NOT use if it appears damaged DO NOT attempt to fix a broken or jammed machine Notify staff immediately Be certain that weight pin is completely inserted Use only the pin provided by the manufacturer If unsure seek assistance Never pin the weights or prop plate into an elevated position DO NOT use the machine if found in this condition DO NOT attempt to fix Seek assistance Inspect cables and their connections before using machine DO NOT attempt to fix Seek assistance Use only the incremental weights supplied by the manufacturer DO NOT use dumbbells or other means to add resistance to the machine Children must not be allowed near this machine Supervise teenagers Manufacturer recommends that all equipment be secured to the floor to stabilize and eliminate rocking or tipping over Use a licensed contractor DO NOT REMOVE THIS LABEL WARN j NG REPLACE IF DAMAGED Lock weight stack when machine is not in use 4 NOTE Lock the weight stack when not using the gym Make sure all the weight plates are rest ing on the plate below with no gap in between Insert the weight selector pin in the tab under neath the weight stack The weight selector pin should be inserted until the knob touches the metal tab Once the pin goes through the weight stack system the weight stack becomes immo bile Verify that the pin has gone through the weight stack stem DIME
6. LIPS PAN HEAD SCREW __55 2 __ 4 _ MOHEXNYLOCKNUT O O OO 545 MAZNCPHLLIPSPANHEADSCREW 46 X 3 8 BLACK PHILLIPS PAN HEAD SCREW oL REQUIRED TOOLS ADJUSTABLE WRENCH MP MI EXTERNAL SNAP RING PLIERS PHILLIPS SCREW DRIVER ALLEN WRENCHES 4mm 7mm 8mm WRENCHES 13mm 17mm 19mm Of 3 8 WASHER 39 M10 X 30MM SCREW 40 M10 X 70MM SCREW 41 1 2 WASHER 43 M12 HEX NYLOCK NUT 44 M12 X 80MM SCREW 42 M10 X 20MM SCREW 48 8 6 M4 X 0 7mm ZINC M10 X 50MM HEX TENSION SCREW 45 PHILLIPS PAN HEAD SCREW 47 RETAINING RING 49 10 32 X 3 4 PHILLIPS PAN HEAD SCREW 50 M6 X 60MM SCREW 51 1 4 WASHER 52 et M4 ZINC 6 X 3 8 BLACK PHILLIPS PAN HEAD PHILLIPS PAN HEAD M10 HEX SCREW 54 SCREW 55 NYLOCK NUT 53 Centimeters STEP 1 Slide the RIGHT BASE 6 over the MOUNTING TUBE of the RIGHT UPRIGHT 4 Loosely secure the RIGHT BASE 6 and RIGHT UPRIGHT 4 to the FRONT UPRIGHT 1 using two M12 x 80mm SCREWS 42 four 1 2 WASHERS 43 and two M12 HEX NYLOCK NUTS 44 as shown With the UPPER SWIVEL PULLEYS 2 oriented as shown insert the UPPER SWIVEL PULLEYS 2 into the top of the RIGHT UPRIGHT 4 and secure together the RIGHT UPRIGHT 4 FRONT UPRIGHT 1 and UPPER SWIV EL PULLEYS 2 using two M10 x 30mm SCREWS 40 and t
7. NECT HOUSING E Slide the QUICK CONNECT HOUSING E COMPRESSION SPRING and QUICK CONNECT SLEEVE onto the cable as shown Insert the cable end into the QUICK CONNECT COUPLER D Q Slide the entire assembly over the QUICK CONNECT COUPLER D Attach the QUICK CONNECT COUPLER D and QUICK CONNECT HOUSING E together Use the two M5 HEX SCREWS H to tighten NOTE IF NECESSARY ENSURE THE CABLES ARE THE PROPER LENGTH AND MAKE NECESSARY ADJUST MENTS TO THE WEIGHT STACK PULLEY TIGHTEN OR LOOSEN 14 STEP 6 Mount the RIGHT BOTTOM PLATE 16 and the LEFT BOTTOM PLATE 17 to the FRONT UPRIGHT 1 using two 10 32 x 3 4 PHILLIPS PAN HEAD SCREWS 50 for each plate Place the FRONT SHROUD 15 around the FRONT UPRIGHT 1 Align the bottom mounting holes of the FRONT SHROUD 15 with the remaining mounting holes on the RIGHT BOTTOM PLATE 16 and the LEFT BOTTOM PLATE 17 Secure with one 10 32 x 3 4 PHILLIPS PAN HEAD SCREW 50 on each plate Attach the bottom corners of the MID BACK COVER 1 to the back of the FRONT SHROUD 15 using two 6 x 3 8 9 5mm BLACK PHILLIPS PAN HEAD SCREWS 55 DO NOT OVERTIGHTEN SCREWS INTO PLASTIC PARTS 15 STEP 7 Remove one QUICK CONNECT from the end of one LOWER LONG CABLE 30 Insert the end where the QUICK CONNECT was removed of the the LOWER LONG CABLE 30 through the LOWER RIGHT PULLEY J and through the access hole in the FOOTPLATE
8. NSIONS gt III Resistance Ratio 1 2 Machine Weight 500 pounds Weight Stack 160 pounds G5 LIVE AREA 12 12 1 1 3 NOTE The live area shows the extent of the G5 gym It does not include the user COMPONENTS LIST NOTE This component list is for ASSEMBLY ONLY For ordering serviceable parts please go to http us home lifefitness com content cfm servicedocuments ITEMNO QTY DESCRIPTION _ OO RTL has 2 woms moms OOOO RON SOU T 9 rioroe 7 38 armenrooc _________ ao f n T gt osme oer tone exec 000000 ml 2 oenm gt E a WT co III Wr III COMPONENTS LIST 42 BMX OM SCREW 83 8 ___44 4 X MPHEXNILOCKNUT 45 2 9M OXSOHEXTENSIIONSCREW _ O 46 2 GUIDERODRETAINER _ OO 42 44 MAX O 7MM ZINC PHILLIPS PAN HEAD SCREW __ _ ___ _____ ______________ 10 32 X 3 4 PHIL
9. ONLY Lifetime for so long as the Customer owns the Life Fitness product LIGHT INSTITUTIONAL USE One 1 year LIMITED WARRANTY ON CABLES AND UPHOLSTERY If the coated cables or upholstery are defective in mate rial or workmanship Life Fitness will repair or replace them at its option Terms IN HOME USE ONLY Three 3 years LIGHT INSTITUTIONAL USE Ninety 90 days CONDITIONS AND EXCEPTIONS Any product misuse abuse or alteration any attempt to repair by a person other than an authorized Life Fitness Service Center any improper assembly accident or any other condition resulting from occurrences beyond the control of Life Fitness will void this Limited Warranty REPLACEMENT AND REPAIR EXPENSES Life Fitness will provide only replacement parts or repair under this warranty The Owner is responsible for all other costs Such costs may include but are not limited to a labor charges for service removal repair or reinstallation of the Life Fitness product or any component part b shipping delivery handling and administrative charges for returning parts to Life Fitness and c all necessary or incidental costs related to installation of the replacement parts SHIPPING If shipping by the Owners is deemed necessary in sole discretion of Life Fitness parts should be shipped in their original carton or equivalent packaging fully insured with shipping charges prepaid Life Fitness will not assume any responsibility for any loss or dam
10. OW IN THE EVENT YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD ON LINE AT WWW LIFEFITNESS COM Model Serial s Note The Model Serial Number label is located towards the bottom of the RIGHT UPRIGHT Date of Purchase Dealer s Name Dealer s Phone Thank you for purchasing the Life Fitness G5 CABLE MOTION GYM SYSTEM 22 LIMITED WARRANTY Life Fitness amp G5 Cable Motion Gym System Life Fitness extends the following LIMITED WARRANTY to the original owner proof of purchase required keep your receipt with this manual of the Life Fitness product The Warranty terms apply to IN HOME and LIGHT INSTITUTIONAL USE ONLY 1 10 LIMITED WARRANTY ON FRAME AND WELDS If the frame of the Life Fitness product or a weld should crack or break it will be repaired or replaced by Life Fitness Terms IN HOME USE ONLY Lifetime for so long as the Customer owns the Life Fitness product LIGHT INSTITUTIONAL USE Ten 10 years LIMITED WARRANTY ON PARTS If the following parts are defective in material or workmanship Life Fitness will supply replacement parts all bolts nuts washers bearings bushings pulleys thumbscrews collars cable retain ing clips adjustable pre stretch slides roller pad shafts allen head bolts weight selector pin weight stack shaft set screws protector caps adjustment chain cotter pin plunger spring and knob Terms IN HOME USE
11. T 1 Make sure the M10 x 50mm HEX TENSION SCREWS 45 in the GUIDE ROD RETAINERS 46 are facing up Push the GUIDE ROD RETAINERS 46 up high enough so that the GUIDE RODS 8 can be placed under them Lower the GUIDE ROD RETAINERS 46 over the GUIDE RODS 22 Slide the RETAINING RINGS 49 up Use External Snap Ring Pliers to secure the RETAINING RINGS 49 into the groove on the GUIDE ROD RETAINERS 46 Tighten all frame bolts securely 12 STEP 4 Remove one QUICK CONNECT from end of one UPPER SHORT CABLE 29 Q Insert the end where the QUICK CONNECT was removed of the UPPER SHORT CABLE 29 through the UPPER SWIVEL PULLEYS 2 and follow routing illustration to the FLOATING PULLEYS 14 through to the HEAD PLATE PULLEY 10 Continue to the other side ending at the other UPPER SWIVEL PULLEYS 2 Reattach the previously removed QUICK CONNECT to the end of the UPPER SHORT CABLE 29 NOTE THE CABLE MUST BE INSERTED BETWEEN THE PULLEY AND THE CABLE RETAINING CLIPS C AND MOVE FREELY 13 QTY DESCRIPTION 6 QUICK CONNECT ASSEMBLY 1 QUICK CONNECT COUPLER 1 QUICK CONNECT HOUSING 1 QUICK CONNECT SLEEVE COMPRESSION SPRING M5 HEX SCREWS Slide Mechanism to insert or Exchange Handles STEP 5 Dissemble the QUICK CONNECT 32 by removing the two M5 HEX SCREWS from the QUICK CONNECT COUPLER D Carefully remove the COMPRESSION SPRING G the QUICK CONNECT SLEEVE F and the QUICK CON
12. age incurred in shipping CLAIM PROCEDURES If service on your Life Fitness product is required during the warranty period please con tact our Customer Service Department at 1 800 351 3737 U S and Canada or 1 847 288 3300 outside of U S and Canada for instructions regarding returning or replacing parts Please have available the following informa tion 1 the dealer s name ii the date of purchase iii the serial s of your product s the serial number loca tion is called out on the final assembly drawing included with your assembly instruction iv a description of the nature of the problem OWNER S RIGHT This Limited Warranty gives you specific legal rights You may also have other rights which vary depending on local law LIMITATION OF IMPLIED WARRANTIES All implied warranties except to the extent prohibited by applicable law shall have no greater duration than the warranty period set forth above There are no warranties which extend beyond the description in this Limited Warranty Because local laws do not allow limitations on how long an implied warranty lasts the above limitations may not apply to you DISCLAIMER No other express warranty has been made or will be made on behalf of Life Fitness with respect to any Life Fitness product or the operation repair or replacement of any Life Fitness product Life Fitness shall not be responsible for injury loss of use of the Life Fitness product inconvenience loss or damag
13. ax 4852 2575 6001
14. children away from strength equipment Parent or others supervising children must provide close supervision of children if the equipment is used in the presence of children Do not allow users to wear loose fitting clothing or jewelry while using equipment It is also recommend ed to have user s secure long hair back and up to avoid contact with moving parts All bystanders must stay clear of all users moving parts and attached accessories and components while machine is in operation SELECTORIZED WEIGHT STACK SYSTEMS T Use only weight selector pins supplied by LIFE FITNESS on weight stacks Substitutes are forbidden Fully insert weight selector pins Partial insertion can cause weights to fall unexpectedly Never pin the weight stack in an elevated position Never remove selector pin if any weights are suspended Never attempt to release jammed weights or parts Never use dumbbells or other means to incrementally increase the weight resistance Use only those means provided by LIFE FITNESS G5 WARNING LABELS A WARNING SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT YOU MUST FOLLOW THESE PRECAUTIONS TO AVOID INJURY Before using read all the warnings and obtain instruction on the use of this machine Use only for intended exercise DO NOT modify the machine Obtain a medical exam before beginning any exercise program Keep body hair and clothing free of all moving objects Inspect the machines before use
15. e to personal prop erty whether direct or indirect and incidental or consequential damages so the above limitation or exclusion may not apply to you Notes 23 HEADQUARTERS 5100 North River Road Schiller Park Illinois 60176 U S A 847 288 3300 FAX 847 288 3703 800 735 3867 Toll free within U S A Canada INTERNATIONAL OFFICES AMERICA S North America Life Fitness Inc 5100 N River Road Schiller Park IL 60176 U S A Telephone 847 288 3300 Fax 847 288 3703 Brazil Life Fitness Do Brazil Av Dr Dib Sauaia Neto 1478 Alphaville Barueri SP 06465 140 BRAZIL Telephone 800 773 8282 Fax 55 11 4133 2893 Latin America amp Caribbean Life Fitness Inc 5100 N River Road Schiller Park IL 60176 U S A Telephone 847 288 3300 Fax 847 288 3703 EUROPE MIDDLE EAST amp AFRICA EMEA Netherlands amp Luxemburg Life Fitness Atlantic BV Bijdorpplein 25 31 2992 LB Barendrecht THE NETHERLANDS Telephone 31 180 646 666 Fax 31 180 646 699 United Kingdom amp Ireland Life Fitness UK LTD Queen Adelaide Ely Cambs CB7 4UB Telephone General Office 44 1353 666017 Customer Support 44 1353 665507 Fax 44 1353 666018 Germany amp Switzerland Life Fitness Europe GMBH Siemensstrasse 3 85716 Unterschleissheim GERMANY Telephone 49 89 31 77 51 0 Germany 41 0848 000 901 Switzerland Fax 49 89 31 77 51 99 Germany 41
16. ons regarding this classification It is recommended that all users of LIFE FITNESS exercise equipment be informed of the following information prior to use ACCESS CONTROL LIFE FITNESS recommends that all fitness equipment be used in a supervised area It is recommended that the equipment be located in an access controlled area Control is the responsibility of the facility owner N INSTALLATION SECURING EQUIPMENT LIFE FITNESS recommends that all equipment be secured to a solid level sur face to stabilize and eliminate rocking or tipping over This must be per formed by a licensed contractor A PROPER USAGE 1 Do not use any equipment in any way other than as designed or intended by the manufacturer It is imperative that LIFE FITNESS equipment is used properly to avoid injury 2 Injuries may result if exercising improperly or excessively It is recommended that all individuals consult a physician prior to commencing an exercise program If at any time during exercise you feel faint dizzy or experience pain STOP EXERCIZING and consult your physician 3 Keep body parts hands feet hair etc clothing and jewelry away from moving parts to avoid injury 4 When adjusting any seat knee hold down pad range of motion limiter foothold pad pulley or any other type of adjuster make certain that the adjusting pin is fully engaged in the hole to avoid injury INSPECTION DO NOT use or permit use of any equipment that i
17. s damaged and or has worn or broken parts For all LIFE FITNESS equipment use only replacement parts supplied by LIFE FITNESS Cables and Belts pose an extreme liability if used when frayed Always replace any cable at first sign of wear consult LIFE FITNESS if uncertain Routinely inspect all accessory clips that join attachments to the cables and replace at the first sign of wear MAINTAIN LABELS AND NAMEPLATES Do not remove labels for any reason They contain important information If unreadable or missing contact LIFE FITNESS for a replacement EQUIPMENT MAINTENANCE Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum Equipment needs to be inspected at regular intervals Ensure that any person s making adjustments or performing maintenance or repair of any kind is quali fied to do so LIFE FITNESS will provide service and maintenance training at our corporate facility upon request or in the field if proper arrangements are made Before any use examine all accessories approved for use with the LIFE FITNESS equipment for damage or wear DO NOT ATTEMPT TO USE OR REPAIR ANY ACCESSORY APPROVED FOR USE WITH THE LIFE FITNESS EQUIPMENT WHICH APPEARS TO BE DAMAGED OR WORN OPERATING WARNINGS 1 It is the purchaser s sole responsibility to properly instruct its end users and supervising personnel as to the proper operating procedures of all LIFE FITNESS equipment Keep
18. wo FLAT 3 8 WASHERS 39 Repeat the above steps to assemble the LEFT UPRIGHT 3 and LEFT BASE 5 to the FRONT UPRIGHT 1 NOTE THE UPPER SWIVEL PULLEYS 2 ATTACH TO THE INSIDE OF THE UPRIGHT SIDES AND THE ORIENTA TION SHOULD BE AS SHOWN 10 2 LOOSELY attach the FOOTPLATE 7 to the RIGHT BASE 6 and LEFT BASE 5 using four M10 x 70mm SCREWS 41 and four FLAT 3 8 WASHERS 39 STEP 3 Position tvo WEIGHT STACK CUSHIONS 13 and GUIDE RODS 8 GUIDE ROD BRACKET B on the bot tom of the FRONT UPRIGHT 1 NOTE MAKE SURE THAT THE PLUGGED ENDS OF THE GUIDE RODS 8 ARE FACING UP D D D LI LI D CAREFULLY slide one of the WEIGHT PLATES 9 over the top of the GUIDE RODS 8 and slowly lower the WEIGHT PLATE 9 on to the WEIGHT STACK CUSHIONS 13 Continue stacking a total of 15 WEIGHT PLATES 9 Slide the TOP PLATE 12 over the GUIDE RODS 8 and slowly lower it onto the WEIGHT PLATES 9 Slide the SELECTOR PIN 11 over the stem of the TOP PLATE 12 Thread the HEAD PLATE PULLEY 10 into the TOP PLATE 12 Slide one RETAINING RING 49 over the top of each of the GUIDE RODS 8 Thread one M10 x 50mm HEX TENSION SCREW 45 into each of the two GUIDE ROD RETAINERS 46 Do not fully thread the M10 x 50mm HEX TENSION SCREWS 45 into the GUIDE ROD RETAINERS 46 CAREFULLY slide the GUIDE ROD RETAINERS 46 into the hole under the top of the FRONT UPRIGH
Download Pdf Manuals
Related Search