Life Fitness X35 User's Manual
Contents
1. near the desired location for use Refer to the Getting Started section of the User Manual for proper location Locate and install the two LEVELER FEET A into the front stabilizer as shown 2 With the DISPLAY CONSOLE MOUNTING PLATE B facing upward lay the UPRIGHT TUBE ASSEMBLY C on floor in front of BASE FRAME D Cut the wire tie securing the LOWER WIRE HARNESS E to the front of the BASE FRAME Connect the UPPER WIRE HARNESS F to the LOWER WIRE HARNESS Position the UPRIGHT TUBE ASSEMBLY C between the FRONT FRAME PLATES G on the BASE FRAME D Feed any excess wire harness into the BASE FRAME Tilt the UPRIGHT TUBE ASSEMBLY into an upright position Align the holes on the plates with the holes on the UPRIGHT TUBE ASSEMBLY Secure the UPRIGHT TUBE ASSEMBLY to the BASE FRAME using four 67 mm HEX HEAD BOLTS 1 and four NUTS 2 Leave BOLTS loose at this time Using two 30 mm HEX HEAD BOLTS 8 secure the UPRIGHT TUBE ASSEMBLY C to the backside of the SUPPORT PLATE on the BASE FRAME D Tighten the BOLTS securely Tighten the previous four HEX HEAD BOLTS 1 securely Position the right and left FRONT SHROUDS H amp J over the FRONT FRAME PLATES G Secure the FRONT SHROUDS using nine 16 mm SCREWS 4 Tighten the SCREWS securely 3 Locate the USER RIGHT PEDAL LEVER K and PEDAL L marked with an R Position the PEDAL above the PEDAL MOUNTING PLATE M and secure the PEDAL using six 16 mm SCREWS 4 and six LOCK W2. ASHERS 5 Tighten the SCREWS securely Repeat for the USER LEFT PEDAL and PEDAL LEVER 4 Slide one LARGE FLAT WASHER 6 and one LARGE WAVE WASHER 7 onto the USER RIGHT PIVOT SHAFT N Slide the WASHERS fully over the PIVOT SHAFT until seated against the pre installed stop ring Locate the USER RIGHT ROCKER ARM ASSEMBLY O Marked with an R With the top handgrip facing the front of the unit as shown slide the USER RIGHT ROCKER ARM ASSEMBLY onto the USER RIGHT PIVOT SHAFT N until seated against the WASHERS 6 amp 7 Secure the ROCKER ARM ASSEMBLY to the PIVOT SHAFT using one FLAT WASHER 8 LOCK WASHER 9 and 20 mm HEX HEAD BOLT 10 Tighten the BOLT securely Insert one ROCKER ARM END CAP P into the end of the ROCKER ARM SHAFT Repeat the procedure for the USER LEFT ROCKER ARM ASSEMBLY Q Position the rear end of the USER RIGHT PEDAL LEVER K near the USER RIGHT REAR CLEVIS R Position the end of the PEDAL LEVER between the clevis flanges Align the holes and secure as shown using one 74 mm HEX HEAD BOLT 11 and one NUT 2 Tighten the BOLT and NUT securely Position one front and back CLEVIS COVER S amp T over the USER RIGHT REAR CLEVIS R Secure the CLEVIS COVERS using two 8 mm SCREWS 12 Tighten the SCREWS securely SNOIL NAaLSNI AlIAWASSVY Jaulesi Sssoiy SEX R OEX see Lie FURESS Life Fitness offers a Tull line of premier fitness equipment for the home TOTAL BODY ELLIPTICAL CROSS
3. TRAINERS TREADMILLS LIFECYCLE EXERCISE BIKES STAIRCLIMBERS GYMSYSTEMS 5100N RIVERROAD SCHILLER PARK ILLINOIS 60176 LIFEFITNESS COM 2005 Life Fitness a division of Brunswick Corporation All rights reserved Life Fitness is a registered trademarks of Brunswick Corporation Any use of this trademark without the express written consent of Life Fitness is foroidden 7954201 Rev A 06 05
4. X30 amp X3s Cross Trainer 6 Lift the front end of the USER RIGHT PEDAL LEVER k to meet the USER RIGHT ROCKER ARM CLEVIS U Secure the PEDAL LEVER to the ROCKER ARM 2 CLEVIS using one 81 5 mm HEX HEAD BOLT 13 and one NUT 2 Tighten the BOLT and NUT securely Repeat the procedure for the USER LEFT PEDAL Hardware List Item Qty Description ENS 67 mm Hex Head Bolt o DIN LEVER and ROCKER ARM CLEVIS Q Position the front and back ROCKER ARM CLEVIS COVERS S amp T over the USER RIGHT ROCKER ARM CLEVIS U Secure the CLEVIS COVERS using two 1 2 7 Hex Head Nut 3 2 JDmm Hex Head Bolt 8 mm SCREWS 12 Tighten the SCREWS securely Repeat the procedure for the USER LEFT ROCKER ARM CLEVIS V 4 21 16 mm Phillips Screw 4 7 Position the ACCESSORY TRAY W over the DISPLAY CONSOLE MOUNTING PLATE B located at the top of the UPRIGHT TUBE ASSEMBLY C as shown 5 19 8 6 mm Lock Washer Route the CONNECTOR X leading from the DISPLAY CONSOLE MOUNTING PLATE through the large hole in the ACCESSORY TRAY BRACKET Y Secure 6 2 E Large Flat Washer Ec the ACCESSORY TRAY using two 8 mm SCREWS 14 Tighten the SCREWS securely 1 2 Large Wave Washer SS Position the DISPLAY CONSOLE Z over the DISPLAY CONSOLE MOUNTING PLATE B located at the top of the UPRIGHT TUBE ASSEMBLY C Plug the 8 2 Flat Washer CONNECTOR X leading from the DISPLAY CONSOLE MOUNTING PLATE into the corresponding CONNECTOR in the back of the DISPLAY CONSOLE M
5. ake 9 2 18 1 mm Lock Washer sure the CONNECTOR snaps into place Push excess wire harness into the opening of the DISPLAY CONSOLE MOUNTING PLATE 10 2 20 mm Hex Head Bolt Plug the HEART RATE CONNECTOR AA leading from the ACCESSORY TRAY W into the corresponding CONNECTOR in the back of the DISPLAY 11 1 74 mm Hex Head Bolt CONSOLE Make sure the CONNECTOR snaps into place la OEE Eaa a X3 5 Only Plug the LOWER CONSOLE CONNECTOR BB leading from the ACCESSORY TRAY W into the corresponding CONNECTOR in the back of the i ii pene 7 DISPLAY CONSOLE Make sure the CONNECTOR snaps into place mm Large FNIPS screw 15 4 12 mm Phillips Screw Secure the DISPLAY CONSOLE to the DISPLAY CONSOLE MOUNTING PLATE B using four 12 mm SCREWS 15 Tighten the SCREWS securely CAUTION Be careful not to pinch the wire harnesses when assembling the DISPLAY CONSOLE Z to the DISPLAY CONSOLE MOUNTING PLATE B 8 Refer to the Getting Started section of the User Manual for proper location stabilizing and POWER ADAPTER instructions 1 amp 2 6 Levelers amp Monocolumn Pedal Lever amp Rocker Arm Assembly Assembly Guide Look for the number coded hardware bags that match the assembly sequence 3 Pedals Pedals amp Right Rear Accessory Tray amp Pedal Lever Console 10 wo sD 4 5 70 OB W 10 10 W WD 10 1 10 Assembly Sequence Tools required Metric Socket set Phillips Screwdriver Metric Wrench set 1 Position the base unit
Download Pdf Manuals
Related Search