Liebherr Refrigerator HCB 2062 User's Manual
Contents
1. Installation Instructions For Fully Integrated NoFrost Combined Refrigerator Freezers HC 2062 1 a a HCB 2062 IMPORTANT PLEASE READ AND FOLLOW THESE INSTRUCTIONS These instructions contain Warning and Caution statements This information is important for safe and efficient installation Always read and follow all Warning and Caution statements es WARNING M Warning indicates a potentially hazardous situation which if not avoided could result in death or serious injury es CAUTION Caution indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury IMPORTANT This highlights information that is especially relevant to a problem free installation Make sure incoming voltage is the same as the unit rating To reduce the risk of fire electric shock or personal injury installation work and electrical wiring must be done by a qualified electrician in accordance with all applicable codes and standards including fire rated construction TO THE INSTALLER It is very important that the guidelines and instructions are followed in the manual2. 35 13 16 910 mm Figure 1 D 3 76 mm E 24 610 mm G 42 7 16 1078 mm H 37 1 8 943 mm cag Door swing clearence Figure 2 Please allow for door swing clearance at locations next to a wall The illustrated measurement is without mounted front panels Be sure to add your panel thickness and handle depth to this measurement in order to avoid interferences SFs Lae I Q Figure 3 It is important to use the provided cover grille for the ventilation opening This opening must not be covered with a cabinet base ll mal gt 76 mm Figure 2 PLANNING INFORMATION Cabinet Opening Dimensions Figure 4 Frameless faceframe cabinet For appliance with panel to be E ma pene flush adjacent cabinetry depth 24 must equal appliance depth 24 E a ilar nes toe i IMPORTANT Do not install the shut off valve behind the appliance The position of the electri cal outlet is possible within the grey shaded areas or above the appliance 92 max 15 3 8 390 mm 3 b y 40 1016 mm Max 78 1980 mm Max Water line opening Water supply line 4 36 K Figure 4 IMPORTANT IMPORTANT
3. Figure 29 9 Screw on the hex nuts to the adjusting bolts 6 Transfer the lower edge of the attachment and inger tomen temporari Fgura 23 bracket onto the panel using a pencil Figure 27 Remove the panel from the refrigerator door Figure 29 Figure 27 15 INSTALLATION 10 Move the panel to the left until it makes contact 13 Extend the soft stop cylinder and connect with with the center rail Figure 30 the ball stud Figure 32 11 Tighten the hex nuts finally I x eS Figure 32 Figure 30 14 Click cover into place Figure 33 12 Fasten the refrigerator panel using the same screws that held the lower bracket before removal Figure 31 ey Figure 33 ON Figure 31 16 INSTALLATION Mounting the ventilation grille Figure 34 35 1 Pull out the bottom freezer drawer 2 Remove the blue protection film from the dust filter provided and insert the filter into its opening in the toe kick area as shown in Figure 34 Attach the filter at the bottom press down the button and click into place Figure 34 3 Mount the ventilation grille as shown in Figure 35 IMPORTANT Only use the ventilation grille provided with the appliance This grille is required for proper operation of the appliance The ventilation opening must not be covered with a cabinet base Failure to use the supplied grille can result in produ
4. For 24 cabinets the water line opening must be in the The free length of the water supply line must be at least location as shown in Figure 4 31 1 2 800 mm when the tube comes out of the pre With cabinets deeper than 24 there is room to fit the penibed Opening pipe behind the appliance and the wall so there are no requirements for the water line lead out position PLANNING INFORMATION Panel Dimensions Inset Installation Style Figure 5 o The panels should be at least 5 8 inch 16 mm Appliance and panels sit fully within the opening thick to allow the connecting rails to be fastened to and are flush with what could be its own box them between two pantry cabinets or decorative columns etc This is the most common installation IMPORTANT scenario The maximum panel thickness is 3 4 19 mm You can order stainless steel panels for inset installation style Refrigerator door panels 80 article number 9900 337 00 Refrigerator door panels 84 article number 9900 335 00 Freezer drawer panels article number 9900 323 00 Cabinet Opening A Refrigerator door panel B 80 2032 mm 45 1 4 1150 mm 84 2134 mm 49 1 4 1251 mm 1 4 17 3 4 m lt 1 4 13 7 16 341 mm 1 4 35 3 4 16 9 16 908 mm 421 mm 4 Figure 5 PLANNING INFORMATION Panel Dimensions Frameless Installation Style Figure 6 The gap between panels with frameless
5. Measuring for mounting the wooden spacer on frameless kitchen cabinets Figure 11 Depth of spacer depending on clearance between appliance and wall 1 1 2 Figure 11 IMPORTANT If the floor slopes down sideways the anti tipping bracket must be fitted horizontally Lay down spacers in the appropriate positions Cover strips Figure 12 Before connection to the water supply the cover strips provided must be fitted to the appliance It is necessary because the appliance will be moved into its recess e Remove the cover band from the strips and stick them to the left and right front edge of the appli ance housing Figure 12 Figure 12 IcEMAKER IiceMaker The icemaker for the combined refrigerator freezer is located in the freezer compartment These instructions only refer to the installation of the ice maker Please refer to the Use and Care Manual provided with the appliance for operation instruc tions The combined refrigerator freezer must be level for the icemaker to function properly Safety Instructions and Warnings Do not install the water connection while the combined refrigerator freezer is connected to an electrical outlet e The connection to the water supply may only be made by a trained and licensed plumber e The water quality must comply with the drink ing water regulations for the geographical are
6. installation With this installation style these wider appliance style is 1 4 6 mm The panels should be at least panels partially overlay the shared side gables of 5 8 inch 16 mm thick to allow the connecting rails adjacent cabinetry so as to mimic the look of a to be fastened to them frameless style cabinet IMPORTANT The maximum panel thickness is 3 4 19 mm Cabinet Opening C Refrigerator door panel D 80 2032 mm 45 3 4 1162 mm 84 2134 mm 49 3 4 1264 mm 18 1 8 18 1 8 460 mm c 13 7 16 341 mm 36 1 2 16 9 16 Figure 6 36 BLOCKING FOR SAFETY Mounting the anti tipping device on concrete floors Figure 7 8 Secure the appliance in place so it does not tip forward when the fully stocked door is opened The anti tipping bracket is provided with the appliance fr 1 Mark the center line of the appliance on the back wall Align the anti tipping bracket center to this line ees WARNING Be sure that there is no plumbing or electrical wiring located in this area which ri screws or drills could damage LT 2 Drill a 3 8 diameter hole in any position as Wall Plate shown in Figure 7 using a carbide drill bit The depth of the holes must exceed the overall length of the anchors provided Clean the holes after drilling 3 Attach washer and screw on hex nut to the end of each anchor Drive in all 3 anchors Align the bracket cen
7. to ensure proper installation and operation of the unit The Installation Guidelines section contains important information for making sure the installation is correct Read and understand all the information in Installation Guidelines and in this manual before the unit is installed es CAUTION Always wear protective devices such as protective gloves and eye shields when installing the appliance Also use hearing protection when drilling holes into concrete floors Contents Page Planning Information Unit dimensions ssnsseeeeneeeeeeeeseeeerrerrenreeeeene 4 Unit Venting aces Gcosscnecstcimaccrnedeeruts aneanteecualns 4 Cabinet opening dimensions 0 cecee 5 Panel Dimensions Framed Cabinet DeSIQN ceceeeeeneeee 6 Panel Dimensions Frameless Cabinet Design eeeeeee 7 Blocking For Safety Mounting the anti tipping device on concrete TOO Ne visiona aaas 8 Mounting the anti tipping device on wooden lOO co enema eter oerene nee eki 8 Mounting the anti tipping device at cabinets deeper than 24 oo cecesesecseeceeeeeeeeeeeeeseeeees 9 COVEN SIN IDS iriseora REEE 9 Ice Maker Safety instructions and warningS 10 Water connection s 10 Connection to the water supply 068 10 Installation Leveling the Refrigerator eeeeeeeeees 12 Adjusting the front of the drawer 12 Fasten the appliance in the recess 12 Before mo
8. a where the appliance is located All equipment and devices used to supply the water to the appliance must comply with the cur rent regulations for your geographical area Water Connection e The water supply pressure requirements are different based on whether or not the supplied Liebherr water filter is installed With the filter installed the pressure must be in the range of 40 90 psi 2 8 6 2 bar Without the filter installed the acceptable pressure range is 22 87 psi 1 5 6 bar Failure to meet these require ments will likely result in ice maker malfunction and possibly cause a water leakage that can damage flooring and surrounding furniture e Use a 1 4 OD copper line to connect the water supply to the solenoid valve This is not sup plied with the refrig erator Figure 13 e A shut off valve such as the saddle valve illustrated here must be installed between the hose line and the main water supply so the water supply can be stopped if necessary Figure 13 Do not install the shut off valve behind the refrigeration unit e The solenoid valve has a metric R3 4 male connector A R3 4 metric to a 1 4 OD adapter is supplied with the ice maker e Insert the water strainer provided into the OD adapter with the cavity downwards IMPORTANT Be sure the strainer is inserted with the cavity downwards Otherwise the strainer could be damaged when mounting the OD adapter onto the solenoid valve C
9. ct failure and will void the warranty Figure 35 17
10. drawers with the strips provided Remove the foil from the adhesive surface of the strip and stick on the top of the appliance drawer Figure 23 making sure the flexible gasket is fully inserted in the gap ss Screw 3 5 x 13 mm Figure 23 Mounting the refrigerator door panels Figures 24 33 The description is for one panel only The procedure is the same for both panels 1 Open the refrigerator door and hang the panel on the adjusting bolts Figure 24 2 Screw on the hex nuts to the adjusting bolts and finger tighten temporarily Figure 24 Figure 24 3 Close the door and check the height of the panel 4 Align the panel in its vertical position if necessary Loosen the hex nuts and turn the adusting bolts using a screwdriver for slotted screws Figure 25 Figure 25 14 INSTALLATION To make it possible to fasten the refrigerator 7 Dismantle the lower attachment bracket from the panel at the bottom the soft stop cylinder must be refrigerator door Align the bracket to the lines on dismantled the refrigerator door panel Figure 28 Fasten the bracket with any hole wherever 5 Grasp the soft stop cylinder and pull down possible using a minimum of 6 screws 4 x 16 Figure 26 mm ees CAUTION The soft stop cylinder retracts in the detached state Figure 28 8 Open the refrigerator door and hang the panel Figure 26 on the adjusting bolts
11. ld result in fire or electric shock ees WARNING M ELECTROCUTION HAZARD Electrical grounding required This appliance is equipped with a three prong grounding polarized plug for your protection against possible shock hazards e Do not remove the round grounding prong from the plug e Do not use a two prong grounding adapter e Do not use an extension cord to connect power to the unit ees CAUTION To protect the appliance from possible damage allow the appliance to stand 1 2 to 1 hour in place before turning the electricity on This allows the refrigerant and system lubrication to reach equilibrium Customer s Responsibility A 115 Volt 60 Hz 15 Amp fused electrical supply is required We recommend using a dedicated circuit for this appliance to prevent electrical overload Follow the National Electrical Code and local codes and ordinances when installing the receptacle Blocking for Safety The anti tipping brackets must be installed to prevent the unit from tipping after it is installed Refer to Blocking for Safety Unit Venting Do not restrict the air flow Air flow must be provided for the unit to operate PLANNING INFORMATION Unit Dimensions Figure 1 Unit Venting Figure 3 HC HCB 20 appliances do not require any ventilation openings in the cabinet The required airflow is directed through the toe kick area A 3 76 mm B 79 13 16 2027 mm C
12. onnection to the Water Supply 1 Move the appliance towards the final position and leave enough space to work behind 2 Insert the water supply line into it s intended opening at the back of the appliance Figure 14 D Figure 14 3 Move the power supply line to the area of the electrical outlet ees WARNING E Do not connect to the electrical outlet before the installation is completed and the water line is connected to the solenoid valve ICEMAKER 4 Push the appliance slowly to the back wall until the compressor mounting plate makes contact with the anti tipping bracket Figure 15 ees WARNING To prevent the appliance from tipping forward the compressor mounting plate must have contact with the anti tipping bracket Figure 15 Figure 16 Anti tipping bracket Compressor mounting plate Figure 15 Figure 17 5 Remove the cover from the valve connector Figure 16 9 Open the shut off valve for the water supply and check the entire water system for leaks 6 The water line is visible at the front of the y aplliance Connect the water line with the OD IMPORTANT adapter Figure 16 After starting up the appliance the water pipe system must be purged of any air Refer to chapter Bleeding the ice maker in the operating instructions 7 Bleed the air from the water line by opening the water supply temporarily 8 Screw the OD adapter
13. onto the refrigerator doors Figure 21 INSTALLATION Mounting the attachment brackets onto the door panels Figure 22 Mark lines on the refrigerator door panels as shown in Figure 22 Align the dismounted brackets of the refrigerator doors to the lines on the refrigerator door panels as shown in Figure 22 a Fasten each bracket with any hole wherever possible using a minimum of 6 screws 4x 16mm Fasten the brackets provided onto the freezer drawer panels using three screws 4 x 16 mm for each bracket Figure 22 b 1 gt 1 3 IHEI A i C Refrigerator door panels 41 1041 mm 1 8 3mm Freezer drawer panel 34 21 32 880 mm 1 8 3 mm Freezer drawer panel 34 21 32 1 8 3 mm 880 mm Figure 22 Figure 22 b 13 INSTALLATION Mounting the freezer drawer panels Figure 23 1 Pull out the upper freezer drawer and screw on the panel with three screws at left and right hand side using the screws as shown in Figure 23 Close the drawer and check the position to the surrounding cabinet panels Align the panel in vertical direction by loosening the screws left and right Finally tighten the screws es CAUTION Do not overtighten Do not use a power driver 3 Pull out the lower freezer drawer and fasten the lower panel in the same way Finally cover the gap between the drawer and the panel of both freezer
14. onto the solenoid valve Figure 17 11 INSTALLATION Leveling the Appliance Figure 18 1 Adjust the height of the appliance at the front by twisting the leveling feet A F 27 Use the open ended spanner provided 2 Adjust the height of the appliance at the rear by turning the adjusting bolts 3 Rotate leveling feet Q until firmly in place against the floor ees WARNING E To prevent the appliance from tipping forward the leveling feet Figure 19 must have contact with the floor B 0 Lhi Figure 18 Adjusting the front of the drawer Figure 19 If required the front of the freezer drawers can be adjusted Transfer the screws shown in the illustration on the left and right sides of the freezer drawer individu ally to the long slots below Tighten the screws in the front of the drawer once it is in the right position lt _ Side view of the freezer drawer pulled out Figure 19 Fasten the appliance in the recess Figure 20 Fasten the appliance in the recess through the upper and lower hinges of the refrigerator doors Use 2 screws for each hinge Figure 20 Before mounting the door panels Figure 21 Remove cover and unscrew the upper attachment bracket 2 of both refrigerator doors These brackets will be mounted onto the refrigerator door panels IMPORTANT The nuts are needed to fit the premounted panels
15. ter to the center line on the back wall again p Figure 8 Fasten the anchors by turning the hex nut K 4 Fasten bracket with 3 screws 1 4 x 2 1 8 into the wall plate Figure 8 Wall Plate Mounting the anti tipping device on wooden floors Figure 9 1 Mark the center line of the appliance on the back wall Align the anti tipping bracket center to this line ees WARNING M Be sure that there is no plumbing or electrical wiring located in this area which screws or drills could damage 2 Fasten bracket to the wooden floor using 5 screws 1 4 x 2 1 8 Drill pilot holes if neces sary 3 Fasten bracket with 3 screws 1 4 x 2 1 8 into lt 7 A the wall plate Lae Figure 9 Wall Plate BLOCKING FOR SAFETY Mounting the anti tipping device in cabinets deeper than 24 Figure 10 11 To ensure the compressor mounting plate reaches the anti tipping bracket in cabinets deeper than 24 a wooden spacer must be mounted between the appliance back and the wall The anti tipping bracket will be fastened to the floor downwards and to the spacer backwards es WARNING Be sure the wooden spacer is fastened securely to the floor Measuring for mounting the wooden spacer on inset kitchen cabinets Figure 10 l Depth of spacer depending on clearance between appliance and wall 1 1 2 35 24 lt Panel thickness Figure 10
16. unting the door panels 12 Mounting the attachment brackets onto the door panels ce eeeeeeeeeeeeeeeeeeees 13 Mounting the freezer drawer panels 14 Mounting the refrigerator door panels 14 17 Mounting the ventilation grille 17 INSTALLATION GUIDELINES Area Requirements Verify the following e Floors can support refrigerators weight plus approximately 1200 pounds 544 kg of food weight e Finished kitchen floor height is level Appliance must be shimmed level if the floor heights are not equal to make sure air vents are not obstructed e Remove anything attached to rear or side walls that can obstruct appliance opening e Cutout dimensions are accurate e Electrical outlet is in correct location Do not install this refrigerator freezer next to any other refrigerator Installing this refrigerator freezer next to any other refrigerator or freezer can cause condensation or cause damage to the appliance Electrical Requirement If codes require a separate grounding circuit to be used have a qualified electrician install the circuit es WARNING Do not ground to a gas pipe Check with a qualified electrician if you are not sure the appliance is properly grounded Do not have a fuse in the neutral or grounding circuit ees WARNING ELECTRIC SHOCK HAZARD e Electrically ground appliance e Do not use an extension cord e Failure to follow these instructions cou
Download Pdf Manuals
Related Search