Liebherr Refrigerator ECBN 5066 User's Manual
Contents
1. Leveling the appliance 1 Adjust the height of the appliance at the front by twisting the leveling feet Use the open ended spanner provided Turn the spanner counterclockwise to raise the appliance front and clockwise to lower it Position the spanner accordingly 1 2 Adjust the height of the appliance at the rear by turning the ad justing bolts O Use a 1 4 box spanner or the Torx 25 wrench provided 3 Rotate leveling feet O until firmly in place against the floor ees WARNING IES To preventthe appliance from tipping forward the level ing feet must have contact with the floor 1 TM Torx 25 2 ZA Fastening the appliance in the recess Once in the recess secure the appliance to the body of the unit using the securing plates 4 x 16 screws Then click the covers sup plied into place Adjusting the refrigerator door The lateral tilt of the refrigerator door can be adjusted if required Undo screws D Adjust the lateral tilt using the grub screw Allen key A F 2 5 Adjusting the front of the drawer If required the front ofthe freezer drawers can be adjusted Transfer the screws shown in the illustration on the left and right sides of the freezer drawer individually to the long slots below Tighten the screws in the front of the2. 3 Screws 6 x 60 mm Connection to the water supply Safety instructions and warnings e Donotconnecttothe water supply whilethecombinedrefrigerator freezer is connected to the electricity supply e The connection to the mains water supply may only be made by trained personnel e The water quality must comply with the drinking water directives of the country in which the appliance is used e The ice maker is designed exclusively to make ice cubes in quantities required by a household and may only be operated with water suitable for this purpose e All repairs and work on the ice maker may only be carried out by customer service personnel or other trained personnel The manufacturer cannotacceptliability for damage caused by a faulty connection to the mains water supply Water pressure The water pressure must be between 0 15 and 0 6 MPa 1 5 6 bar Important If the water filter is inserted in the appliance the water pressure must lie between 0 3 and 0 6 MPa 3 6 bar If the water pressure with the inserted water filter is too low this may cause the ice maker to malfunction The water supply to the appli ance must be through a cold water pipe that can withstand the operating pressure andcom plies with the hygiene regula tions For this use the stainless steel hose supplied length 3 m Installation 1 Place the appliance in front of the installation recess 2 Apply cover strips above bet wee
3. Installation instructions for NoFrost combined refrigerator freezers aro o fms 7083 461 00 CAN ECBN 5066 Content Page SP FERN 2 Electrical connection usersnneneesnnnnnnnnnennnnnennnnnnnnnnnnn nennen nn 2 Appliance Vent Qin dadas e 2 Door swing clearance unersnneneesnnnnnnnnnnnnnnnnnnnnn conan rn ernennen 2 Appliance dimensions uessrnneenennnnennennnnnnnnnnennnnnn ernennen 3 Installation dimensions ur4ssnser nenn ennennnnnnnnnnn nennen nennen 3 Mounting the anti tipping device uusersnnnennnnnnnnnnnnn nennen nennen 4 MOUNTING Options ea Connection to the water supply Leveling the appliance 22us444nsernnnenennnnnnnnnnnnnn nennen nenne Fastening the appliance in the recess uunneesersnnenen seen nennen 7 Adjusting the refrigerator door ueessneesennnnsnnnnnnnnnnnnnnnnnnnnnnennn ne 7 Adjusting the front of the drawer uusnssesnersnennernnnennnnennnnn nenne 7 Mounting the ventilation grille 8 Before fitting the door panels uurssueersnnnennnnnnnnnnnnn nennen nenn 9 Panel dimensions u een 9 Mounting the attachment brackets onto the door panels 10 Mounting the refrigerator panel unsersnsesersnnnnnnnnnnennnn nenn 11 Mo
4. drawer once it is in the right position Side view of the freezer drawer pulled out Mounting the ventilation grille Pull out the bottom freezer drawer _ Remove the blue protection film from the dust filter provided and insert the filter into its opening in the plinth Engage the filter at the bottom press down the button and click into place 6 Install the ventilation grille The grille has bolts on the inside see detail in the drawing below These bolts must be inserted into the holes of the supports N Remove the locking pins of both supports The supports are provided with the appli ance accessory pack 3 Insert the supports for the ventilation grille on the left and right sides in the motor compartment N Adjust the height of the ventilation grille Loosen the grub screws at the front of the grille Allen key A F 2 5 Adjust the ventilation grille to the desired height Tighten the grub screws A The front edge of the brackets is flush with the front of the ventilation grille N k Adjustthe supports accordingly p en SSB Before fitting the door panels Remove the cover O and unscrew the top and bottom attach ment brackets O from the refrigerator door These attachment brackets will be mounted onto the refrigerator door panel Important The securing nuts are needed for re mounting the pre assembled door pane
5. frigerator 4 Close the refrigerator door and check the height of the panel door completely ig A 5 Adjust the height of the panel if necessary Undo the securing nuts and use the adjusting pins to adjust fig C t ZA t Torx 15 t fig A 6 Adjust the panel horizontally using the long slots in the attach ment bracket fig D 2 Open the refrigerator door and suspend the refrigerator panel 7 Tighten the securing nuts on the top adjusting pins fig B 3 Screw securing nuts onto the adjusting pins and slightly tighten 11 8 Remove the adjusting pins bottom of the refrigerator door 10 Undo the three screws on the top of the attachment bracket until these touch the attachment bracket fig E adjust the door panel as displayed in fig G and then retighten the screws The same procedure can be carried out for the bottom attachment bracket 11 Click the top and bottom covers into place 1 fig H Insert the cover strip provided 2 between refrigerator door and panel 9 Screw on the securing nuts and tighten fig F A fig F 12 Mounting the freezer panels 1 Pulloutthe top freezer drawer and screw onthe pre assembled panel The same screws must be used as those used to screw onthe attachment brackets 3 5 x 13 2 Close the freezer drawer and check the position of the panel Adjust the height of the panel by undoing the left and right screws Tighte
6. l onto the refrigerator door Unscrew the attachment brackets O from the freezer drawers Theseattachmentbrackets will be mounted ontothefreezerpanels Important The screws are needed for re mounting the pre assembled freezer panels onto the freezer drawers u Panel dimensions Min panel thickness 16 mm Max panel thickness 19 mm Maximum panel weight Refrigerator panel 27 kg Freezer drawer panel 10 kg _ Ges SIND 1162 mm 6 mm 341 mm 1 4 421 mm 762 mm Mounting the attachment brackets onto the door panels 1 Draw a line 1041 mm from the bottom side of the door panel 2 Draw a further line 107 5 mm from the bottom side of the door panel 3 Align one of the refrigerator door attachment brackets to the top line as shown in the illustration below and secure with at least 6 screws 4 x 14 4 Align the second refrigerator door attachment bracket to the bottom line as shown in the illustration below and secure with at least 6 screws 4 x 14 5 Secure each of the attachment brackets that have been removed from the freezer drawers using 3 screws 4 x 14 as shown in the illustration below Refrigerator door panel 1041 mm 107 5 mm Freezer drawer panel 737 mm Freezer drawer panel 737 mm 10 Mounting the refrigerator panel 1 Screw in the adjusting pins on the underside of the re
7. n and below the securing plates on the side walls of the appliance Cut the cover strips to the right length for this purpose k 907 Fit the adhesive cover strips mm leavingagapof6 5mmtoeach securing plate This ensures problem free fitting ofthe cov ers 722 mm 3 Insert the bent section of the hose through the opening at the right side of the appliance 4 Move the hose to the front and con nect with the valve connector Be sure the connection is tightly arranged Valve connector 8 Push the appliance slowly into the recess until the compressor 5 Locate the water hose into the rail of mounting plate touches the anti tipping bracket the appliance base 6 Route the mains cable towards the socket 7 Route the water hose towards the water shut off tap CA N WARNING IO Do not connect the appliance to the power supply until the 9 Fill the hose with water and connect to the shut off tap installation is completed Be sure the connection is tightly arranged cs CAUTION HEMER Open the shut off tap and check the system for leakage Lay the mains cable and the water hose in such a way that they will not be damaged when the appliance is slid into the installation recess Important After the ice maker has been switched on the water supply system must be bled See the section Bleeding the ice maker in the operating instructions
8. n the screws 3 Pull out the bottom freezer drawer and mount the panel in the same way 4 For both drawers cover the gap between the drawer and the panel with the cover strips supplied Remove the protective film from the trim and insert into the gap at the top 3 5 x 13mm Changing over door hinges Door hinges should only be changed by a trained expert es WARNING IES Do not try to change over the door hinges yourself The refrigerator door hinges are fitted with strong closing springs If the hinge accidentally snaps shut this can lead to serious injury 13 14 15 Liebherr Hausger te Lienz GmbH Dr Hans Liebherr Strasse 1 A 9900 Lienz www liebherr com
9. nd alone inverters conversion of direct currentto alternating three phase cur rent or energy saving plugs Risk of damage to the electronic control system Appliance venting The required air flow is directed through the plinth Itis importantto use the provided ventilation grille forthe ventilation opening This opening must not be cov ered Failure to use the supplied grille can result in product failure and will void the warranty Door swing clearance Please allow for doorswingclearance at locations next to a wall The illustrated measurement is with out mounted front panels Be sure to add your panel thickness and handle depth to this measure ment in order to avoid interferences Appliance dimensions A 76mm B 2027 mm C 757mm D 610 mm E 1403 mm F 943 mm 1975 mm line indicates the height measured from the floor 1 This type of dimension E55 5 mm 861 5 mm 65 mm 512 5 mm 177 5 mm Installation dimensions The location of the socket can within a radius of 2000 mm from the appliance top center Y gt 2000 mm 762 mm gt The ice maker is fitted in the freezer compartment of the combined refrigerator freezer It must be connected to the mains water sup ply to work The water shut off valve must be positioned within the areas marked in gre
10. unting the freezer panelS nuusrnnesnernnnnennnnnnn nennen nennen 13 Changing over door hinges ccoooconoccccoconoccconcnonanconccinrnnnnc cnn cnn 13 Setting up e Avoid positioning the appliance in direct sunlight ornear cookers radiators and similar sources of heat The floor on which the appliance stands should be horizontal and level The ventilation grilles should not be obstructed Always ensure that there is good ventilation and that the outward flowing air is able to escape Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m per 8 g of R 600a refrigerant used in the appliance so as to avoid the formation of inflammable gas air mixtures in the room where the appliance is located in the event of a leak in the refrigerant circuit The quantity of refrigerant used in your appliance is indicated on the type plate on the inside of the appliance Electrical connection Only operate the appliance with alternating current AC The permissible voltage and frequency are indicated on the type plate The position of the type plate is shown in the description of the appliance The socket must be properly earthed and protected by a fuse The tripping current of the fuse must be between 10 A and 16 A The socket must not be situated behind the appliance and must be easily accessible Do not connect the appliance using an exten sion cable or extension socket Do not use sta
11. y Important Do not install the shut off valve behind the appliance es WARNING MENS The water shut off valve must not sit directly above the socket The gap between the water shut off valve and the socket mustcomply withthe regulations of the country in which the appliance is used Mounting the anti tipping device Mounting options U N WARNING IO The supplied anti tipping bracket must be installed in all cases This prevents the appliance from tipping over when the fully loaded door is opened Mounting the bracket with the wall studs Mounting with plugs to concrete walls 3 Screws 6 x 60 mm es CAUTION INMI Ensure that there are no electric cables or water pipes in the wall section to which the anti tipping bracketis tobe secured These could be damaged during installation Mounting with the wall plate turning in the screws at an angle Installation 3 Screws 6 x 60 mm 1 Mark the centre line of the appliance on the floor Align the anti tipping bracket centre to the centre line 2 Depending on the constitution of the floor and wall use any pos sible mounting option as shown in chapter Mounting Options The screws 6 x 60 are supplied with the accessory pack Important If the floor slopes down sideways the anti tipping DA bracket must be fitted horizontally Lay down spacers y gt in the appropriate positions N Mounting with wooden floors Mounting with plugs to concrete floors
Download Pdf Manuals
Related Search