Liebherr Oven liebherr User's Manual
Contents
1. Before fitting the door panels Remove the cover O and unscrew the attachment bracket from the refrigerator doors These attachment brackets will be mounted onto the refrigerator door panels Important The securing nuts are needed for re mounting the pre assembled door panels onto the refrigerator doors Unscrew the attachment brackets from the freezer drawers Theseattachmentbrackets willbe mounted onto the freezer panels Important The screws are needed for re mounting the pre assembled freezer panels onto the freezer drawers GB Panel dimensions Min panel thickness 16 mm Max panel thickness 19 mm Maximum panel weight Refrigerator panel 27 kg Freezer drawer panel 10 kg 6mm 460 mm 460 mm 1162 mm f vamm 6 17 Mounting the attachment brackets onto the door panels Mark lines on the refrigerator door panels as shown in Fig A Align the dismounted brackets of the refrigerator doors to the lines on the refrigerator door panels as shown in Fig A 1 Fasten each bracket with any hole wherever possible using a minimum of 6 screws 4 x 16 mm Fasten the brackets provided onto the freezer drawer panels using three screws 4 x 16 mm for each bracket Fig A2 25 5 mm 25 5mm Refrigerator door panels 1041 mm 3mm Freezer drawer panel Fig A 2 880 mm Freezer drawer panel 3 mm 880 mm CD Fig A Fig A 2 12. 6 bar Important If the water filter is inserted in the appliance the water pressure must lie between 0 3 and 0 6 MPa 3 6 bar If the water pressure with the inserted water filter is too low this may cause the ice maker to malfunction The water supply to the appliance must be through a cold water pipe that can withstand the operating pressure and complies with the hygiene regulations For this use the stainless steel hose supplied length 3 m Installation 1 Place the appliance in front of the instal lation recess 2 Applycoverstripsontheside walls of the appliance 3 Insert the bent section of the hose through the opening at the rear of the appliance 4 Connect the hose to the solenoid valve at the front side of the appliance 5 Route the mains cable towards the socket 6 Route the water hose towards the water shut off valve m Ze A WARNING ME Do not connect the appliance to the power supply until the installation is completed cs CAUTION HEMER Lay the mains cable and the water hose in such a way that they will not be damaged when the appliance is slid into the installation recess GB 7 Push the appliance slowly into the recess until the compressor mounting plate touches the anti tipping bracket es WARNING HENEEEEEEEEEE To preventthe appliance from tipping f
3. rs The required air flow is directed through the plinth It is important to use the provided ventilation grille for the ventila tion opening This opening must not be covered Appliance dimensions A 76mm B 2027 mm C 910 mm D 76 mm E 910 mm G 1078 mm H 943 mm Installation dimensions The socket must be positioned within the areas marked in grey or above the installation recess GB The ice maker is fitted in the freezer compartment of the combined refrigerator freezer It must be connected to the mains water sup ply to work The water shut off valve must be positioned within the areas marked in grey es WARNING BEE The water shut off valve must not sit directly above the socket The gap between the water shut off valve and the socket mustcomply with the regulations of the country in which the appliance is used 2300 mm 2032 mm 4000 mm 915 mm 2000 mm 13 14 Mounting the anti tipping device a A WARNING The supplied anti tipping bracket must be installed in all cases This prevents the appliance from tipping over when the fully loaded door is opened Installation 1 Mark the centre line of the appliance on the floor Align the anti tipping bracket centre to the centre line es CAUTION HEMER Ensure that there are no electri
4. 8 Mounting the refrigerator panel The description is for one panel only The procedure is the same for both panels 1 Open the refrigerator door and suspend the refrigerator panel on the top adjusting pins fig B 2 Screw securing nuts onto the adjusting pins and slightly tighten fig B 3 Close the refrigerator door and check the height of the panel 4 Adjust the height of the panel if necessary Undo the securing nuts and use the adjusting pins to adjust fig C GB To make it possible to fasten the refrigerator panel at the bottom the soft stop cylinder must be dismantled 5 Stick a small screwdriver under the retaining clamp and lever out fig D fig D 6 Grasp the soft stop cylinder and pull down Fig E The soft stop cylinder retracts in the detached state fig E 7 Transferthe lower edge of the attachment bracket onto the panel using a pencil fig F Remove the panel from the refrigerator door 19 20 8 Dismantle the lower attachment bracket from the refrigerator door Align the bracket to the lines on the refrigerator door panel fig G Fasten the bracket with any hole wherever possible using a minimum of 6 screws 4 x 16 mm 9 Opentherefrigerator door and suspend the refrigerator panel on the top adjusting pins fig H 10 Screwsecuring nuts onto the adjusting pins and slightly tighten fig H 11 Mov
5. Installation instructions for NoFrost combined refrigerator freezers oo oo oo SS ar eo oe 7082 551 00 ECBN 6256 12 Setting up e Avoidpositioning the appliance in direct sunlight or near cookers radiators and similar sources of heat e The floor on which the appliance stands should be horizontal and level e The ventilation grilles should not be obstructed Always ensure that there is good ventilation and that the outward flowing air is able to escape e Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m per 8 g of R 600a refrigerant used in the appliance so as to avoid the formation of inflammable gas air mixtures in the room where the appliance is located in the event of a leak in the refrigerant circuit The quantity of refrigerant used in your appliance is indicated on the type plate on the inside of the appliance Electrical connection Only operate the appliance with alternating current AC The permissible voltage and frequency are indicated on the type plate The position of the type plate is shown in the description of the appliance The socket must be properly earthed and protected by a fuse The tripping current of the fuse must be between 10 A and 16 A The socket must not be situated behind the appliance and must be easily accessible Do not connect the appliance using an exten sion cable or extension socket Appliance venting L
6. c cables or water pipes in the wall section to which the anti tipping bracketis to be secured These could be damaged during installation 2 Secure the anti tipping bracket to the floor using the 3 screws 6 mm x 60 mm included in the accessory pack The distance between the leading edge of the body of the unit and the rear edge of the anti tipping bracket is 610 mm Important When securing the anti tipping bracket to a concrete floor use suitable plugs If the floor slopes down sideways the anti tipping bracket must be fitted horizontally Lay down spacers in the appropriate positions Connection to the water supply Safety instructions and warnings e Donotconnectto the water supply while the combined refrigerator freezer is connected to the electricity supply The connection to the mains water supply may only be made by trained personnel e The water quality must comply with the drinking water directives of the country in which the appliance is used e The ice maker is designed exclusively to make ice cubes in quantities required by a household and may only be operated with water suitable for this purpose e All repairs and work on the ice maker may only be carried out by customer service personnel or other trained personnel The manufacturer cannotacceptliability for damage caused by a faulty connection to the mains water supply Water pressure The water pressure must be between 0 15 and 0 6 MPa 1 5
7. ess the button down and click the filter into place Mounting the ventilation grille Important To ensure fault free operation of the appliance you must install the supplied ventilation grille Donotobstructthe ventilation opening or cover it with a panel 21 Liebherr Hausgerate Lienz GmbH Dr Hans Liebherr Strasse 1 A 9900 Lienz www liebherr com
8. ethe panel to the left until it makes contact with the center rail fig 1 12 Tighten the hex nuts finally fig 13 Fasten the refrigerator panel using the same screws that held the lower bracket before removal fig K 6 mp fig K 14 Extend the soft stop cylinder and connect with the ball stud fig L fig L 15 Attach the retaining clamp to the ball housing of the soft stop cylinder fig M fig M 16 Click cover into place fig N fig N Mounting the freezer panels 1 Pulloutthe top freezer drawer and screw onthe pre assembled panel The same screws must be used as those used to screw onthe attachment brackets 3 5 x 13 Close the freezer drawer and check the position of the panel Adjust the height of the panel by undoing the left and right screws Tighten the screws Pull out the bottom freezer drawer and mount the panel in the same way For both drawers cover the gap between the drawer and the panel with the cover strips supplied Remove the protective film from the trim and insert into the gap at the top GB Mounting the dust filter The supplied dust filter prevents that dirt enters the motor compart ment reducing the refrigeration performance Therefore always install the dust filter 1 Pull the bottom freezer drawer right out 2 Remove the protective film from the dust filter Insert the filter at the bottom pr
9. orwards the compres sor mounting plate must be touching the anti tipping bracket Anti tipping bracket Compressor mounting plate 8 Connect the hose to the shut off tap Open the shut off tap and check the system for leakage Important After the ice maker has been switched on the water supply system must be bled See the section Bleeding the ice maker in the operating instructions 15 16 Levelling the appliance 1 Adjust the height of the appliance at the front by twisting the adjustable feet A F 27 Use the open ended spanner provided Caution The front feet of the ap pliance must be firmly placed on the floor 2 Adjustthe height ofthe appliance atthe rear by turning the adjusting bars 2 Turn the adjusting bars clock wise until the compressor mount ing plate touches the anti tipping bracket Adjusting the front of the drawer If required the front of the freezer drawers can be adjusted Transfer the screws shown in the illustration on the left and right sides of the freezer drawer individually to the long slots below Tighten the screws in the front of the drawer once it is in the right position Side view of the freezer drawer pulled out Fasten the appliance in the recess Fasten the appliance in the recess through the upper and lower hinges of the refrigerator doors Use 2 screws for each hinge screws 4 x 16 mm
Download Pdf Manuals
Related Search