Liebherr HCS 20 User's Manual
Contents
1. Savar Installation Instructions For Fully Integrated NoFrost Of I Combined Refrigerator Freezers Instructions de montage Pour le r frig rateurs cong lateurs combin s NoFrost encastr s D Ill pour une utilisation int gr e _ Instrucciones de instalacion Para combinados frigorifico congelador NoFrost incorporados para uso integrado Parlez vous fran ais Voir page 15 Habla espanol V ase pagina 29 IMPORTANT PLEASE READ AND FOLLOW THESE INSTRUCTIONS These instructions contain Warning and Caution statements This information is important for safe and efficient installation Always read and follow all Warning and Caution statements D Z WARNING Ea Warning indicates a potentially hazardous situation which if not avoided could result in death or serious injury es CAUTION SSSR Caution indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury IMPORTANT This highlights information that is especially relevant to a problem free installation Make sure incoming voltage is the same as the unit rating To reduce the risk of fire electric shock or personal injury install2. Figure 2 Please allow for door swing clearance at locations next to a wall 3 1 2 89 mm Figure 2 Unit Venting Figure 3 HCS 20 appliances do not require any ventilation openings in the cabinet The required airflow is directed through the toe kick area Figure 3 It is important to use the provided cover grille for the ventilation opening This opening must not be covered with a cabinet base PLANNING INFORMATION Cabinet Opening Dimensions Figure 4 Electrical outlet I A IMPORTANT Do not install the shut off valve behind the appliance c E a D 15 3 8 Water line opening B 24 3 4 629 mm Water supply line C 80 2032 mm a 1 He A gt IMPORTANT IMPORTANT At 24 cabinets the water line opening must be in the The free length of the water supply line must be at least 31 1 2 800 mm when the tube comes out of the location as shown in Figure 4 At cabinets deeper than 24 there is room to fit the pipe behind the appliance and the wall so there are no requirements for the water line lead out position prescribed opening
3. 10 Before mounting the door panels 10 Mounting the attachment brackets onto the door panels ccseeeeseen esses 11 Mounting the refrigerator door panels 12 13 Mounting the ventilation grille 14 INSTALLATION GUIDELINES Area Requirements Verify the following e Floors can support refrigerators weight plus approximately 1200 pounds 544 kg of food weight e Finished kitchen floor height is level Refrigerator must be shimmed level if the floor heights are not equal to make sure air vents are not obstructed e Remove anything attached to rear or side walls that can obstruct refrigerator opening e Cutout dimensions are accurate e Electrical outlet is in correct location Do not install this refrigerator freezer next to any other refrigerator Installing this refrigerator freezer next to any other refrigerator or freezer can cause condensation or cause damage to the appliance Electrical Requirement If codes require a separate grounding circuit to be used have a qualified electrician install the circuit ees WARNING SSSR Do not ground to a gas pipe Check with a qualified electrician if you are not sure the appliance is properly grounded Do not have a fuse in the neutral or grounding circuit es WARNING SSSR ELECTRICAL SHOCK HAZARD e Electrically ground refrigerator e Do not use an extension cord e Failure to follow these instructions could result in fire or
4. electrical shock ees WARNING SSSR ELECTROCUTION HAZARD Electrical Grounding Required This appliance is equipped with a three prong grounding polarized plug for your protection against possible shock hazards e DO NOT remove the round grounding prong from the plug e DO NOT use a two prong grounding adapter e DO NOT use an extension cord to connect power to the unit ees CAUTION SSSR To protect the refrigerator from possible damage allow the appliance to stand 1 2 to 1 hour in place before turning the electricity on This allows the refrigerant and system lubrication to reach equilibrium Customer s Responsibility A 115 Volt 60 Hz 15 Amp fused electrical supply is required We recommend using a dedicated circuit for this appliance to prevent electrical overload Follow the National Electrical Code and local codes and ordinances when installing the receptacle Blocking For Safety The anti tip bracket must be installed to prevent the unit from tipping after it is installed Refer to Blocking For Safety Unit Venting Do not restrict the air flow Air flow must be provided for the unit to operate PLANNING INFORMATION Unit Dimensions Figure 1 ls HN Lt A 3 17 32 90 mm B 79 13 16 2027 mm C 35 13 16 910 mm D 3 1 2 89 mm E 24 7 32 615 mm G 42 7 16 1078 mm H 39 7 16 1002 mm Figure 1 Door swing clearence
5. BLOCKING FOR SAFETY Mounting the anti tipping device on concrete floors Figure 5 6 Secure the appliance in place so it does not tip for ward when the fully stocked doors are opened The anti tipping bracket is provided with the appliance Wall 1 Mark the center line of the appliance on the back wall Align the anti tipping bracket center to this line ees WARNING SSSR Be sure that there is no plumbing or electrical wiring located in this area which screws or drills could damage 2 Drill a 3 8 diameter hole in any position as shown in Figure 4 using a carbide drill bit Wall Plate The depth of the holes must exceed the overall g length of the anchors provided Figure 5 Clean the holes after drilling 3 Attach washer and screw on hex nut to the end of each anchor Drive in all 3 anchors Align the bracket center to the center line on the back wall again Fasten the anchors by turning the hex nut 4 Fasten bracket with 3 screws 1 4 x 2 1 8 into the wall plate Figure 6 Wall Plate Figure 6 BLOCKING FOR SAFETY Mounting the anti tipping device on wooden floors Figure 7 1 Mark the center line of the appliance on the back wall Align the anti tipping bracket center to this line ees WARNING SSSR Be sure that there is no plumbing or electrical wiring located in this area which screws or drills could damage 2 Fasten bracket to the wooden floor using 5 scr
6. SSSR To prevent the appliance from tipping forward the leveling feet D Figure 14 must have contact with the floor 4 Align refrigerator with sides of kitchen cabinets by adjusting leveling feet and the supports 27 mm wrench A deB i 5 mm socket Figure 14 Cover plate for 84 cabinets In the panel set for 84 cabinets the plate provided can be used to cover the space between aplliance housing and cabinet top Screw the cover plate on the appliance housing using two screws M5 x 15 Figure 15 Figure 15 Fasten the appliance in the recess Figure 16 Fasten the appliance in the recess through the upper and lower hinges of the refrigerator doors Use 2 screws for each hinge Figure 16 screws 4 x 16 mm Figure 16 10 INSTALLATION Mounting the attachment brackets onto the door panels The refrigerator door panels comes in a separate package delivered with the appliance 1 Unscrew the upper attachment brackets of both 3 Fasten the attachment bracket onto the panel refrigerator doors Figure 17 for the right refrigerator door using 4 x 16 mm screws Figure 19 Figure 17 2 Remove cover plate of both panels Figure 18 3 Fasten the attachment bracket onto the panel for Replace this cover plate once attachment of the the left refrigerator door using 4 x 16 mm screws pa
7. ation work and electrical wiring must be done by a qualified electrician in accordance with all applicable codes and standards including fire rated construction TO THE INSTALLER It is very important that the guidelines and instructions are followed in the manual to ensure proper installation and operation of the unit The Installation Guidelines section contains important information for making sure the installation is correct Read and understand all the information in Installation Guidelines and in this manual before the unit is installed es CAUTION SSSR Always wear protective devices such as protective gloves and eye shields when installing the appliance Also use hearing protection when drilling holes into concrete floors Contents Page Planning Information Unit dimensions 4 Unit Venting sers radins 4 Cabinet opening dimensions ssesesase1 5 Blocking For Safety Mounting the anti tipping device on concrete TOONS x2sincesiaceaaceiteeyesecnaacddinetetendacsseurcetedcraags teins 6 Mounting the anti tipping device on wooden TOONS rennais 7 Mounting the anti tipping device in cabinets deeper than 24 3 4 7 Ice Maker Safety instructions and warnings 8 Water connection 8 Connection to the water supply 9 Installation Leveling the refrigerator 10 Fasten the appliance in the recess
8. d injury or damage do not forget to secure the soft stop device with the retaining clamp 10 Fasten the refrigerator panel with three screws 4 x 16 mm at the bottom Figure 26 Figure 25 Aa Figure 28 Figure 26 13 INSTALLATION Mounting the ventilation grille Figure 29 30 1 Pull out the bottom freezer drawer 2 Remove the blue protection film from the dust filter provided and insert the filter into its opening in the toe kick area as shown in Figure 29 Figure 29 3 Mount the ventilation grille as shown in Figure 30 IMPORTANT Only use the ventilation grille provided with the appliance This grille is required for proper operation of the appliance The ventilation opening must not be covered with a cabinet base Failure to use the supplied grille can result in product failure and will void the warranty Figure 30 14
9. ews 1 4 x 2 1 8 Drill pilot holes if neces sary 3 Fasten bracket with 3 screws 1 4 x 2 1 8 into the wall plate Figure 7 Wall Plate Mounting the anti tipping device in cabinets deeper than 24 3 4 Figure 8 To ensure the compressor mounting plate reaches the anti tipping bracket at cabinets deeper than 24 a wooden spacer must be mounted between the appliance back and the wall The anti tipping bracket will be fastened to the floor downwards and to the spacer backwards es WARNING SSSR Be sure the wooden spacer is fastened securely to the floor Depth of spacer depending on clearence between appliance and wall 1 1 2 24 3 4 Figure 8 ICEMAKER IceMaker The icemaker for a combined refrigerator freezer is located in the freezer compartment It must be connected to the water supply to function properly These instructions only refer to the installation of the icemaker Please refer to the Use and Care Manual provided with the appliance for operation instructions The combined refrigerator freezer must be level for the icemaker to function properly Safety Instructions and Warnings Do not install the water connection while the combined refrigerator freezer is connected to an electrical outlet The connection to the water supply may only be made by a trained and licensed plumber The water quality must comply wit
10. h the drink ing water regulations for the geographical area where the appliance is located Water Connection The water pressure must be between 21 8 87 0 psi 1 5 6 bar Use a 1 4 OD copper line to connect the water supply to the solenoid valve This is not sup plied with the refrigerator Figure 9 A shut off valve such as the saddle valve illus trated here must be installed between the hose line and the main water supply so the water sup ply can be stopped if necessary Do not install the shut off valve behind the refrigeration unit Figure 9 e If you have hard water we recommend you install a water softener Also a filter must be installed if the water contains solids such as sand All equipment and devices used to supply the water to the appliance must comply with the cur rent regulations for your geographical area Cover strips Figure 10 Before connection to the water supply the cover strips provided must be fitted to the appliance It is necessary because the appliance will be moved into its recess Remove the cover band from the strips and stick them to the left and right front edge of the appli ance housing Figure 10 Figure 10 ICEMAKER Connection to the Water Supply 1 Install the shut off valve water filter and auto matic shut off device as required The solenoid valve has a Metric R3 4 male con nector A R3 4 metr
11. ic to a 1 4 OD adapter is supplied with the icemaker Move the appliance towards the final position and leave a gap of approx 30 behind Insert the water supply line into its intended opening at the back of the appliance Figure 11 Move the power supply line to the area of the electrical outlet es WARNING SSSR Do not connect to the electrical outlet before the installation is completed and the water line is connected to the solenoid valve Push the appliance slowly to the back wall until the compressor mounting plate makes contact with the anti tipping bracket Figure 12 es WARNING SSSR To prevent the appliance from tipping forward the compressor mounting plate must have contact with the anti tipping bracket Figure 12 The water line is visible at the front of the appli ance Screw the OD adapter onto the solenoid valve and connect the water line with the adapt er Figure 13 Open the shut off valve for the water supply and check the entire water system for leaks Anti tipping bracket Compressor mounting plate Figure 12 Figure 13 INSTALLATION Leveling the Refrigerator Figure 14 1 The height can be adjusted in front by twisting the leveling feet 2 Twist the adjusting bolt to set up the back of the refrigerator 3 Rotate leveling feet until firmly in place against the floor es WARNING
12. nels is complete Figure 20 Figure 18 Figure 20 11 INSTALLATION Mounting the refrigerator door panels Figures 21 28 1 Open the left refrigerator door and suspend the 5 Close the door and check the height of the panel on the adjusting bolts Figure 21 panel 2 Screw on the hex nuts to the adjusting bolts and 6 Align the panel in its vertical position if tighten temporarily Figure 21 necessary Loosen the hex nuts and turn the adusting bolts using a screwdriver for slotted screws Figure 23 7 Check the vertical position of the panel again and tighten the hex nuts finally Figure 23 Figure 21 g 3 Loosen the three cross head screws of the To make it possible to fasten the refrigerator bracket and move the panel to the left until it panel at the bottom the soft stop cylinder must be makes contact with the center rail Figure 22 dismantled 8 Stick a small screwdriver under the retaining 4 Tighten the three cross head screws Figure 22 clamp and lever out Figure 24 Figure 24 Figure 22 12 INSTALLATION 9 Grasp the soft stop cylinder and pull down 11 Extend the soft stop cylinder and connect with Figure 25 the ball stud Figure 27 ees CAUTION SSSR The soft stop cylinder retracts in the detached state Figure 27 12 Attach the retaining clamp to the ball housing of the soft stop cylinder Figure 28 es CAUTION SSSR To avoi
Download Pdf Manuals
Related Search