Home

Liebert AccuVar User's Manual

1. 280 3 Separately Derived System The TVSS shall be connected on the load side of the first overcurrent device in a separately derived system Disconnect Switch If Provided All SPD units must still be connected to the load side of the main service disconnect or load side of a protected circuit s disconnecting means Surge Voltage Ratings To obtain the suppression voltage ratings SVRs as obtained by Underwriters Laboratory Incorporated in accordance with the Standard for Safety Transient Voltage Surge Suppressors TVSS Standard 1449 Second Edition dated August 15 1996 marked on this product the wire size listed for each product must be utilized to connect the unit to your facilities power grid Connections made with conductors other than the wire size listed may result in different SVRs Circuit Ampacity Limitations Representative samples of these products have been investigated by Underwriters Laboratories Incorporated to withstand without exposing live circuits or components at system voltages and fault currents ranging from 14 000 AIC up to 200 000 AIC as described in the Standard for Safety Transient Voltage Surge Suppressor TVSS Standard 1449 Second Edition dated August 15 1996 Verify each products fault current rating on the individual installation pages that follow Liebert TVSS Units SL 22085 Rev 2 11 2006 0 Liebert Surge Suppression Systems VOLTAGE RATINGS AND POWER SOURCE CONFIG
2. 80 LM060 LM080 5A 150A 4 1 0 40 Amp LM100 LM150 5A 175A 15A 100A 14 2 0 14 2 40 LM200 LM250 15A 175A 14 2 0 100 Amp Ava 155 34 Wc 30Amp LPM 100 2 PowerSure LPM 1PM1002 30 30 12 Provided LPM 160 Surge Voltage Ratings obtain the suppression voltage ratings SVRs as obtained by Underwriters Laboratory Incorporated in accordance with the Standard for Safety Transient Voltage Surge Suppressors TVSS Standard 1449 Second Edition dated August 15 1996 marked on this product the suggested wire size must be utilized to connect the unit to your facilities power grid Connections made with conductors other than the size provided may result in different SVRs 6 Connection to Form contacts shall be with 18 22 AWG The ratings of the Form contacts are 5 amps at 250 maximum with a power factor of 1 0 For additional information on Interceptor Il connections see page 15 7 Apply power The surge protectoris fully operational when the GREEN LEDs on the modules and the front door of enclosure are illuminated If the GREEN LEDs are extinguished or a RED LED is illuminated check to ensure that power is applied to the SPD If an abnormal indication is present remove power to the SPD and contact Liebert Emerson Network Power Surge Protection at 1 800 288 6169 or 1 607 724 2484 8 Periodically monitor the status of the L
3. IM EEEE dd 5 System Groundingiand EE n 6 SPD MOMONA aat tech re re Rate ER PD ebbe ere RE e NL diane RU RE Re d 6 TROUBLESHOOTING SERVICING MAINTENANCE s esses hh nen 7 Troubleshooting aee prr pne PUE EHE UN UT ASW PROMIS MU eI REPE WI EUR A downed uma RIS Red 7 Servicing RE CREE OPERI NR Y Kus IY DER Ea Rau 7 Ese PER 7 Preventative Maintenance Inspection and Cleaning sese eee 7 PRODUCT INSTALLATIONS 1 15 om th Ra eere tia T VAEN EE E TAR REE RETO de Coa ERA ETE E ERE 8 Typical Parallel Installation Type SI H SS LM ACV LPM amp 1 mee 8 Active Tracking Filter Type F Series vet eae pa e rre qr vo A RR EI I ERIU EDUC HU REA ER TERRAARIO ve 10 PanelG ard Series Type LPGE Series edo prre X A NE RR MEE RAMS EUN 12 Accu amp uide SEES ACG iiiter ert i NE RE ds 13 DIMENSIONAL INFORMATION 9x gr ree px DERE erie tna EE E FUE REN NES VER PORE 15 Int rceptorl Seres Type Sl 2 15 Hybrid Advantage Series EIE Y wield VEE E EEEE E Ane Era d 16 AccuVar I Ea ERE hanson E E Eae sea m PEE 16 Active T
4. Manual Liebert TVSS Units SL 22085 Rev 2 11 2006 Factory Setting 9 Liebert Surge Suppression Systems Active Tracking Filter Series Type F lt Large Bezel 2 0 Max Options Small Bezel 50 Max No Options Typical Cabinet Data 30 to 400Amps Typical Cabinet Data 800 to 4000Amps Current Dimensions Inches Rating XXX VOLTAGE Application D E FxxxN L30 Single Phase 9 0 21 25 10 0 FxxxS30 Split Phase 9 0 25 25 14 0 FxxxD30 Three Phase Delta 9 0 25 25 14 0 FxxxY30 Three Phase Wye 9 0 25 25 14 0 FxxxN L60 Single Phase 9 0 21 25 10 0 FxxxS60 Split Phase 9 0 25 25 14 0 FxxxD60 Three Phase Delta 9 0 25 25 14 0 FxxxY60 Three Phase Wye 9 0 25 25 14 0 FxxxN L100 Single Phase 9 0 25 25 14 0 FxxxS100 Split Phase 9 0 31 25 18 0 FxxxD100 Three Phase Delta 9 0 31 25 18 0 FxxxY100 Three Phase Wye 9 0 31 25 18 0 FxxxN L225 Single Phase L N 9 0 25 25 14 0 Fxxx 225 Split Phase 9 0 31 25 18 0 FxxxD225 Three Phase Delta 9 0 31 25 18 0 FxxxY225 Three Phase Wye 9 0 31 25 18 0 FxxxD400 Three Phase Delta 12 0 49 25 30 0 400 Three Phase Wye 12 0 49 25 30 0 Current Model Dimensions Inches Rating XXX VOLTAGE Application c FxxxD800 Three Phase Delta 48 0 12 0 FxxxY800 Three Phase Wye 48 0 12 0 FxxxD1200 Three Phase Delta 48 0 20 0 FxxxY1200 Three Phase Wye 48 0 20 0 FxxxD2000 Three Phase Delta 48 0 20 0 FxxxY2000 Three Phase Wye 48 0 20 0 FxxxD4000 Thr
5. a worst case need for the panel or switchgear end our SPD will be much less than 5 feet We recommend cutting the pigtail to the shortest length possible A CAUTION Caution Pigtails must be supported if pulling AccuGuide assembly through conduit Grip only the blue coaxial cable body when pulling the assembly through conduit Do not pull AccuGuide assembly using the pigtails or damage may occur Installation Operation and Maintenance Manual 14 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Alarm Contacts X2 Pin 1 Normally Open Pin 2 Common i Pin 3 Normally Closed Liebert Hi o Surge Suppression Systems Dimensional Information Interceptor Il Series Type SI Phase L1 A 5 Breaker for Panel Service Panel for Loads to be Protected N Dedicated Neutral Buss Disconnect Optional Ground Buss C Recommended Wire Entrance W Liebert Hi o 1 840 Interceptor Il Type SI Wire Range Dimensions Inches Suggested Allowable Suggested CNS EE Range 5016 16 5032 S1040 16 16 17 25 10 0 44 15A 175A 14 2 0 SI050 5100 TOOA UD E Interceptor Il Type 3 with Rotary EGE Dimensions Inches Suggested Leia Allowable Allowable Wire Size reaker ee des w Tes a Hn age SI016 28 51032 51040 20 16 21 25 10 0 44 58 80 4 15A 175 14
6. is fully operational when the GREEN LEDs are illuminated Ifthe GREEN LEDs are extinguished check to ensure that power is applied to the SPD If an abnormal indication is present remove power to the SPD and contact Liebert Emerson Network Power Surge Protection at 1 800 288 6169 or 1 607 724 2484 12 Periodically monitor the status of the LEDs Reduced protection exists if the GREEN LEDs are extinguished Please contact Liebert Emerson Network Power Surge Protection at 1 800 288 6169 or 1 607 724 2484 13 The protection modules in these SPDs are replaceable contact Liebert Emerson Network Power Surge Protection for replacement Installation Operation and Maintenance Manual 12 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems Liebert AccuGuide Series Type ACG SPD Interconnect Assembly Installation Instructions All electrical connections shall be installed by a qualified licensed electrician All wiring must comply with the National Electrical Code NEC and applicable local codes National Electrical Code NEC Considerations The National Electrical Code Article 240 21 details specific tap rules that should be considered before installation NEC 240 21 Location in Circuit Over current protection shall be provided in each ungrounded circuit conductor and shall be located at the point where the conductors receive their supply except as specified in 240 21 A through C No conductor supplied under
7. s business General Liebert Corporation products and systems are in our opinion the finest available We take pride in our products and are pleased that you have chosen them Under certain circumstances we offer with our products the following Ten Year Warranty Against Defects in Material and Workmanship Please read your Warranty carefully This Warranty sets forth our responsibilities in the unlikely event of defect and tells you how to obtain performance under this Warranty TEN YEAR LIMITED WARRANTY AGAINST DEFECTS IN MATERIAL AND WORKMANSHIP LIEBERT PRODUCTS COVERED Interceptor Transient Voltage Surge Suppressors Interceptor Active Tracking Filters Hybrid Advantage Transient Voltage Surge Suppressors AccuVar Transient Voltage Surge Suppressors and Type SS Transient Voltage Surge Suppressors Terms of Warranty As provided herein the Liebert product is warranted to be free of defects in material and workmanship for a period of ten 10 years from the date of product shipment from Liebert The shipment date will be determined only from the Liebert bill of lading If any part or portion of the Liebert product fails to conform to the warranty within the warranty period Liebert at its option will furnish new or factory remanufactured parts for repair or replacement of that part or portion Warranty Extends to First Purchaser for Use Non transferable This Warranty is extended to the first person firm association or corpora
8. should be read before starting installation These instructions do not replace national or local electrical codes Check applicable electrical codestoensure compliance Installation ofthe Liebert SPD system should only be performed by qualified personnel UNPACKING AND INSTALLATION Unpacking and Preliminary Inspection 1 Inspect the shipping crate s for damage or signs of mishandling before unpacking the unit 2 Remove any securing bands and cardboard packing and inspect the unit for any obvious shipping damages 3 Ifany damageasaresultofshippingisobserved immediately file a claim with the shipping agency and forward a copy to your local Liebert Sales Representative Handling Considerations Larger units are bolted to a shipping palletto facilitate handling by forklift or pallet jack Check the size and weight Refer to the cabinet data furnished with the unit Storage The unit should be stored in a clean dry environment Storage temperature range is 55 C 67 F to 85 C 185 F Care should be taken to avoid condensation All packing and shipping materials should be left intact until the unit is ready for final installation If the unit has been stored for an extended period of time the unit should be cleaned and carefully inspected before placing into service Location Considerations Environment The unit is designed for operation indoors in ambient temperatures of 40 C 40 F to 60 C 140 F with a relati
9. submittal drawings for typical mounting dimensions and weight Warnings Defined Danger Indicates an imminently ADANGER hazardous situation that if not avoided will result in death or serious injury This signal word is to be limited to the most extreme situations Warning Indicates a potentially hazardous situation that if not avoided could result in death or serious injury Caution Indicates a potentially hazardous situation that if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices A CAUTION Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems ELECTRICAL CONNECTIONS All electrical connections should be installed by a qualified licensed electrician only All wiring must comply with the National Electrical Code NEC and applicable local codes VERIFY THAT ALL POWER CIRCUITS ARE DE ENERGIZED AND LOCKED OUT BEFORE MAKING ELECTRICAL CONNECTIONS Voltage Ratings and Power Source Configurations A CAUTION Before making connections to the unit verify that the unit model number and nameplate voltage rating are appropriate for connection to the intended power source See the chart on page 4 for voltage rating applications with typical power source configurations Parallel Connection see Figures on page 5 EQUIPMENT PERFORMANCE For maximum system performance the unit must be located as close to the protected circ
10. the provisions of 240 21 A through G shall supply another conductor under those provisions except through an over current protective device meeting the requirements of 240 4 A Branch Circuit Conductors Branch circuit tap conductors meeting the requirements specified in 210 19 shall be 9 q permitted to have over current protection located as specified in that section B Feeder Taps Conductors shall be permitted to be tapped without over current protection at the tap to a feeder as specified in 240 21 B 1 through 5 1 Taps Not Over 3 m 10 ft Long Where the length of the tap conductors does not exceed 3 m 10 ft and the tap conductors comply with all of the following 1 The Ampacity of the tap conductors 25 Amps in our case is a Not less than the combined computed loads on the circuits supplied by the tap conductors and b Not less than the rating of the device supplied by the tap conductors or not less than the rating of the over current protective device at the termination of the tap conductors 2 The tap conductors do not extend beyond the switchboard panelboard disconnecting means or control devices they supply 3 Except at the point of connection to the feeder the tap conductors are enclosed in a raceway which shall extend from the tap to the enclosure of an enclosed switchboard panelboard or control devices or to the back of an open switchboard 4 For field installations where the tap conduct
11. will be determined only from the Liebert bill of lading If any part or portion of the Liebert product fails to conform to the warranty within the warranty period Liebert at its option will furnish new or factory remanufactured parts for repair or replacement of that part or portion rran ten r fi on rable This Warranty is extended to the first person firm association or corporation for whom the Liebert product specified herein is originally installed for use the User in the fifty United States or Canada This Warranty is not transferable or assignable without the prior written permission of Liebert nment of W nties Liebert assigns to User any warranties which are made by manufacturers and suppliers of components of the Liebert product and which are assignable but Liebert makes NO REPRESENTATIONS as to the effectiveness or extent of such warranties assumes NO RESPONSIBILITY for any matters which may be warranted by such manufacturers or suppliers and extends no coverage under this warranty to such components Dr ri Liebert warrants for the period and on the terms of the Warranty set forth herein that the Liebert product will conform to the certified drawings if any applicable thereto to Liebert s final invoices and to applicable Liebert product brochures and manuals current as of the date of product shipment Descriptions Liebert does not control the installation and use of any Liebert product Accordingly it is understoo
12. 11 2006 0 Liebert Surge Suppression Systems PowerSure Medium Exposure Series Type LPM 100 2 nest Service Panel ase for Loads to Phase L3 C be Protected Disconnect Main Breaker for Dedicated Neutral Buss Optional Ground Buss 6 000 9 v Unit is supplied from the factory with a minimum length of 18 of 12 wire for connection It is recommended that a 30A circuit breaker be used for installation Unit is equipped with Summary Alarm Contacts The 18 wires are designated as follows Phase A Phase B Phase C Service YELLOW Normally Open ORANGE COMMON 4 000 gt BLUE Normally Closed 0 500 ij 0 375 3 500 8 750 8 000 9 31 4X Ground Buss Neutral Buss Unit is supplied from the factory with a minimum length of 18 of 10 wire for connection It is recommended that a 30A circuit breaker be used for installation Dedicated Disconnect Optional Disconnect Main Breaker for Panel Service Panel for Loads to be Protected Phase L3 C Phase L2 B PhaseL1 A Installation Operation and Maintenance Manual 20 Liebert TVSS Units 51 22085 Rev 2 11 2006 Surge Suppression Systems 9 Liebert PowerSure Low Exposure Series Type LPL PhaseL1 A Phase L2 B Phase L3 C Service Panel for Loads to g 188 4X be Protected Disconnect Main Breaker for Panel Neutral Buss 1 2 O
13. 2 0 51050 sno 8 924 a o 88 755 E431 Installation Operation and Maintenance Manual 15 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems Hybrid Advantage Series Type H r Phase L1 A Service Panel for p Phase L2 B Loads to be Protected Phase L3 C Disconnect Main Breaker for Dedicated Neutral Buss Disconnect Optional Ground Buss Recommended Wire Entrance 1 CF 1625 Hybrid Advantage Suggested Suggested Allowable Allowable ths etes mme Wire Range 29 16 9 10 56 re __ 15A 150A M14 1 0 3 420 9 o44 amp soa sa Msasa 14 2 0 333 24 24 9 2525 18 0 44 13115 soa 4 15A 175A 14 2 0 a 3e 2 9 pus 53 2 175 14 20 AccuVar Series Type ACV amp All Service Panel for Loadsto be Protected N Phase Hie Disconnect Main Breaker for Panel Dedicated Neutral Buss E Disconnect Optional Ground Buss Slots Will Accept 8 32 Screws 1 2 Flexible Conduit 9 00 Minimum Trim to Fit 4 125 Alarm Enable Disable Feature Audible Alarm AccuVar Series Alarm ENABLED Alarm DISABLED AccuVar Series Jumper Alarm Jumper Alarm Suggested Allowable Wiese Breaker enable AWG Range 9 Installation Operation and Maintenance
14. 6 or 4 AWG pigtails for connection to the service and to the surge protective device SPD Gauge of the pigtail is based on the SPD lug size See chart below for units and acceptable wire ranges An additional 10 gauge grounding conductor is provided with the AccuGuide assembly for use as an equipment ground Interceptor II Units Acceptable Wire Range All Units No Disconnect 14 2 0 SI016 025 With Disconnect 8 1 0 51032 100 With Disconnect 14 2 0 LM Units Acceptable Wire Range All Units No Disconnect 14 2 LM060 080 With Disconnect 8 1 0 LM100 250 With Disconnect 14 2 0 Conduit The AccuGuide assembly is sold without conduit If conduit housing is required the following conduit and fitting sizes apply No of Conductors Conduit Size in 1 Coax Cable 1 GND 1 2 Coax Cable 1 GND 1 1 4 3 Coax Cable 1 GND 1 1 4 4 Coax Cable 1 GND 11 4 5 Coax Cable 1 GND 11 2 6 Coax Cable 1 GND 11 2 7 Coax Cable 1 GND 11 2 Equipment Performance The ideal SPD installation locates the suppression as close to the protected bus as possible This product was designed to address those instances when a close installation is not possible However while the voltage drop experienced with an AccuGuide assembly is significantly reduced care should be taken to keep connection lengths to a minimum Each end of the AccuGuide assembly is shipped with five foot pigtails The length is offered as
15. All defective products and component parts replaced under this Warranty become the property of Liebert Warranty Performance of Component Manufacturers It is Liebert s practice consistent with its desire to remedy Warranty defects in the most prompt and effective manner possible to cooperate with and utilize the services of component manufacturers and their authorized representatives in the performance of work to correct defects in the product components Accordingly Liebert may utilize third parties in the performance of Warranty work including repair or replacement hereunder where in Liebert s opinion such work can be performed in less time with less expense or in closer proximity to the Liebert product Installation Operation and Maintenance Manual 25 Liebert TVSS Units SL 22085 Rev 2 11 2006 0 Liebert Items Not Covered By Warranty THIS WARRANTY DOES NOT COVER DAMAGE OR DEFECT CAUSED BY misuse improper application wrong or inadequate electrical current or connection negligence inappropriate on site operating conditions corrosive atmosphere repair by non Liebert designated personnel accident in transit tampering alterations a change in location or operating use exposure to the elements Acts of God theft or installation contrary to Liebert s recommendations or specifications or in any event if the Liebert serial number has been altered defaced or removed Notwithstanding the foregoing the following Acts of God are
16. E Surge Protection For Business Critical Continuity Interceptor Il SAD Hybrid Advantage Type SS LM AccuVar PowerSure LPM LPL Series ATF Series PanelGuard Extension AccuGuide Products Installation Operation and Maintenance Manual Hutt SURGE SUPPRESSION s 9 Liebert EMERSON Network Power 0 Liebert Surge Suppression Systems LIEBERT SURGE PROTECTIVE DEVICE INSTALLATION OPERATION AND MAINTENANCE MANUAL TABLE OF CONTENTS UNPACKING AND INSTALLATION hx ERR rk hA E Ee almEYOREIEDHE EAE ETE 2 U packing and Preliminary sx unn ken m es Bete ee ROERIRET agave E RE nese a RN ERR C UR E Peer 2 Handling Considerations s ROI Oeo d EP AR Uere 2 M C eT 2 Location Gonsidenations ss AE OU ETE EDD 2 Door Closing Ad usttrients Sega DH DUE 2 Warnings qq DAR RE Kea 2 ELECTRICAL CONNECTIONS gt Re R3 mese a rE CR ot anes Goes Ee eh EIE ERI E E ERES 3 Voltage Ratings and Power Source Configurations 3 Parallel Corinection ER Rae 3 Voltage Ratings and Power Source Configurations mmm 4 Typical Parallel Connections nce ro RE PNE
17. EDs Reduced protection exists if the GREEN LEDs are extinguished or the RED LED is illuminated Please contact Liebert Emerson Network Power Surge Protection at 1 800 288 6169 or 1 607 724 2484 9 The protection modules in these SPDs may be replaceable contact Liebert Emerson Network Power Surge Protection for replacement Note ACV LPM amp LPL units do not have replaceable modules Installation Operation and Maintenance Manual 9 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems Liebert Active Tracking Filter Series Type F Surge Protective Device SPD Installation Instructions 1 Ampacity The filter s maximum continuous current Ampere rating must be greater than or equal to the protected load s full load amps or overcurrent protection Circuit Breaker rating 2 Insure that all power is removed before beginning installation A qualified licensed electrician shall install all electrical connections 3 The SPD is provided in a NEMA 3R NEMA 4 NEMA 4X or NEMA 12 enclosure The SPD is suitable for use in indoor NEMA 12 or outdoor NEMA 3R 4 4X installations 4 Determine where the SPD is to be mounted Punch or cut proper hole size in the side of the SPD closest to the knockout to be utilized in the service panel Wall Mounted Units Drill mounting holes in wall at location picked for SPD next to service panel using mounting dimension from the tables on page 17 Mount surge suppressor
18. LLOWED WHEN SERVICING THIS UNIT TO PREVENT RISK OF ELECTRICAL SHOCK TURN OFF AND LOCK OUT ALL POWER SOURCES TO THE UNIT BEFORE SERVICING UNIT For servicing assistance contact your local Liebert Sales Representative or Liebert at 800 288 6169 or 607 724 2484 Installation Operation and Maintenance Manual Corrective Maintenance The Liebert SPD is designed for years of trouble free operation However even the most reliable equipment may fail under abnormal conditions Diagnostic indicators are provided to indicate when the unit needs replacement see individual SPD operation of this manual for details To ensure continuity of surge protection failed units should be replaced at the earliest convenient service opportunity When replacing surge modules other components should be inspected for damage and replaced if necessary Standard electrical troubleshooting procedures should be used to isolate problems other than failed surge current diverter modules When replacing components for continued proper operation and safety replace only with identically rated components Please contact factory for information on replacement parts Preventative Maintenance Inspection and Cleaning Periodic system inspections cleaning and connection checks are recommended to ensure reliable system performance and continued surge transient protection It is difficult to establish a schedule for preventative maintenancesinceconditionsvaryf
19. R S SOLE AND EXCLUSIVE REMEDY IS REPAIR OR REPLACEMENT OF THE LIEBERT PRODUCT AS SET FORTH HEREIN IF USER S REMEDY IS DEEMED TO FAIL OF ITS ESSENTIAL PURPOSE BY A COURT OF COMPETENT JURISDICTION LIEBERT S RESPONSIBILITY FOR PROPERTY LOSS OR DAMAGE SHALL NOT EXCEED THE NET PRODUCT PURCHASE PRICE IN NO EVENT SHALL LIEBERT ASSUME ANY LIABILITY FOR INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND WHATSOEVER INCLUDING WITHOUT LIMITATION LOST PROFITS BUSINESS INTERRUPTION OR LOSS OF DATA WHETHER ANY CLAIM IS BASED UPON THEORIES OF CONTRACT NEGLIGENCE STRICT LIABILITY TORT OR OTHERWISE Miscellaneous NO SALESPERSON EMPLOYEE OR AGENT OF LIEBERT IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY Warranty terms may be modified if at all only in a writing signed by a Liebert officer Liebert obligations under this warranty are conditioned upon Liebert timely receipt of full payment of the product purchase price and any other amounts due Liebert reserves the right to supplement or change the terms of this Warranty in any subsequent warranty offering to User or others n the event that any provision of this Warranty should be or becomes invalid and or unenforceable during the warranty period the remaining terms and provisions shall continue in full force and effect This Warranty shall be governed by and construed under the laws of the State of Ohio without reference to the conflict of laws principles t
20. T OR PART THEREOF DOES NOT EXTEND THE ORIGINAL WARRANTY PERIOD Limitations e THIS WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE e USER S SOLE AND EXCLUSIVE REMEDY IS REPAIR OR REPLACEMENT OF THE LIEBERT PRODUCT AS SET FORTH HEREIN e USER S REMEDY IS DEEMED TO FAIL ITS ESSENTIAL PURPOSE BY A COURT OF COMPETENT JURISDICTION LIEBERT S RESPONSIBILITY FOR PROPERTY LOSS OR DAMAGE SHALL NOT EXCEED THE NET PRODUCT PURCHASE PRICE IN NO EVENT SHALL LIEBERT ASSUME ANY LIABILITY FOR INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND WHATSOEVER INCLUDING WITHOUT LIMITATION LOST PROFITS BUSINESS INTERRUPTION OR LOSS OF DATA WHETHER ANY CLAIM IS BASED UPON THEORIES OF CONTRACT NEGLIGENCE STRICT LIABILITY TORT OR OTHERWISE Miscellaneous SALESPERSON EMPLOYEE OR AGENT OF LIEBERT IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY Warranty terms may be modified if at all only in a writing signed by a Liebert officer e Liebert obligations under this warranty are conditioned upon Liebert timely receipt of full payment of the product purchase price and any other amounts due Liebert reserves the right to supplement or change the terms of this Warranty in any subsequent warranty offering to User or others In the event that any provision of this Warranty should be or becomes invalid and or unenforce
21. URATIONS Nominal Operating Volt Model Voltage Cod Source Configurations NR ME ed Edo Maximum Continuous Found inpart number Single Phase L N 2 W G 100 100 150 LN 120Nor 120 L 120 N or 120 120 N or 120 L 230 N or 230 N L 277 N or 277 347 Nor 347 Single Phase L L 2 W 11 L 208L or 208 L 240L or 240 L 400L or 400 12 B 4801 480 L 600L or 600 Single Phase 3 W 120 120 L1 N 240 277 240 277 L2 G 347 Three Phase Delta 3 W G 208 A 240 380 400 415 480 600 Three Phase Delta Hi Leg 4 B 120 240 120 120 240 120 aN 240 480 240 240 480 240 Three Phase Wye 4W G Three Phase Wye 3 W G No Neutral A B Note 1 For other voltages or source configurations consult factory Installation Operation and Maintenance Manual 4 Liebert TVSS Units 51 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems Typical Parallel Connections without Internal Rotary Disconnect s seyd JennaN To Protected Transient Ground Protected Safety Panel Wire should be Ground less than 5 feet and straight as possible Loads Liebert Surge Protective Device Typical Parallel Connections with Internal Rotary Disconnect punosy s seyd Pro
22. able during the warranty period the remaining terms and provisions shall continue in full force and effect Warranty shall be governed by and construed under the laws of the State of Ohio without reference to the conflict of laws principles thereof This Warranty represents the entire agreement between Liebert and User with respect to he subject matter herein and supersedes all prior or contemporaneous oral or written communications representations understandings or agreements relating tothis subject Installation Operation and Maintenance Manual 28 Liebert TVSS Units SL 22085 Rev 2 11 2006 Liebert Corporation 1050 Dearborn Drive P O Box 29186 Columbus OH 43229 800 877 9222 Phone US amp Canada Only 614 888 0246 Outside U S 614 841 6022 FAX Via Leonardo Da Vinci 8 Zona Industriale Tognana 35028 Piove Di Sacco PD Italy 39 049 9719 111 Phone 39 049 5841 257 FAX Emerson Network Power Asia Pacific 7 F Dah Sing Financial Centre 108 Gloucester Road Wanchai Hong Kong 852 25722201 Phone 852 28029250 FAX Liebert com Technical Support 607 724 2484 Phone 607 722 8713 FAX 800 288 6169 Toll Free While every precaution has been taken to ensure the accuracy and completeness of this literature Liebert Corporation assumes no responsibility and disclaims all liability for damages resulting from use ofthis information or for any errors or omissions 2006 Liebert Corporation All rights reserve
23. ault currents of up to 200 000 AIC as described in the Standard for Safety Transient Voltage Surge Suppressor TVSS Standard 1449 Second Edition dated August 15 1996 7 Anexternal circuit breaker is not necessary for over current protection However itis recommended thatthe SPD be connected in series with a 30A circuit breaker The SPD shall be connected in accordance with all national and local electrical codes 8 To obtain the suppression voltage ratings SVRs as obtained by Underwriters Laboratory Incorporated in accordance with the Standard for Safety Transient Voltage Surge Suppressors TVSS Standard 1449 Second Edition dated August 15 1996 marked on this product 8 AWG wire must be utilized to connect the unit to your facilities power grid Connections made with conductors other that 48 AWG may result in different SVRs 9 Connect black wires line or phase marked L1 A L2 B or L3 C the white wire neutral marked and the green wire ground marked C of the SPD using the wire range listed in the table below in accordance with the National Electric Code NEC Article 285 and all local codes To yield the best performance of the SPD within the electrical distribution system keep all conductors as short as possible and avoid sharp bends 10 Connection to the Form contacts shall be with 18 22 AWG Contacts are rated 5 amps at 250 VAC maximum with power factor of 1 0 11 Apply power The surge protector
24. covered lightning induced surges which are transients spikes or other sub cycle discontinuous events impinging on normally applied voltage as defined by reference data in the latest version of IEEE C62 41 and the Liebert product performance specifications THIS WARRANTY DOES NOT COVER shipping costs installation costs circuit breaker resetting or maintenance or service items and further except as provided herein does NOT include labor costs or transportation charges arising from the replacement of the Liebert product or any part thereof or charges to remove or reinstall same at any premises of the User THIS WARRANTY DOES NOT COVER DAMAGE OR DEFECT CAUSED BY use of the Liebert product in combination with any electrical or electronic components circuits systems assemblies or other materials not furnished by Liebert Liebert does NOT warrant the suitability for use or the results of the Liebert product in combination with the products of others THE PRODUCTS LISTED IN THIS WARRANTY ARE NOT DESIGNED FOR USE IN THE FOLLOWING APPLICATIONS i ANY NUCLEAR OR RELATED APPLICATIONS AND ii LIFE SUPPORT AND PATIENT CONNECTED AND APPLIED MEDICAL AND DENTAL APPLICATIONS REPAIR OR REPLACEMENT OF A DEFECTIVE PRODUCT OR PART THEREOF DOES NOT EXTEND THE ORIGINAL WARRANTY PERIOD limitations THIS WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE USE
25. d that the Descriptions are NOT WARRANTIES OF PERFORMANCE and NOT WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE btaining Perf This W s Within a reasonable time but in no case to exceed thirty 30 days after User s discovery of a defect User shall contact Liebert at 1 800 LIEBERT 543 2378 and request a return authorization number User shall ship the product with proof of purchase to Liebert freight prepaid Liebert products shipped to Liebert without a retum authorization number will be refused and retumed freight collect to User at Users expense Liebert products shipped by User to Licbert which have incurred freight damage due to User s improper packaging of the product will not be covered by this Warranty and any repairs or replacement parts components or products needed will be invoiced in the full current price amount and returned freight collect to User Subject to the limitations specified herein Liebert will repair or replace at its option without charge for Liebert labor or materials subsequent to its inspection and F O B Liebert s facility the Liebert produd that does not conform to the Warranty Replacement parts components or products shipped to User prior to Liebert s receipt and inspection of the product claimed to be defective shall be invoiced in the full current price amount and shipped freight collect F O B Liebert s facility Warranty coverage will be extended only after Liebert s receipt of the claimed defective pro
26. d throughout the world Specifications subject to change without notice Liebert and the Liebert logo are registered trademarks of Liebert Corporation All names referred to are trademarks or registered trademarks of their respective owners 51 22085 11 06 Rev 2 82290 Printed in USA Emerson Network Power The global leader in enabling Business Critical Continuity Emerson Network Power com E Power E Embedded Computing Outside Plant Racks and Integrated Cabinets Bl Connectivity E Embedded Power E Power Switching amp Controls Bl Services DC Power E Monitoring Precision Cooling E Surge Protection Emerson Network Power the Emerson Network Power logo and Business Critical Continuity are trademarks and service marks of Emerson Electric Co 2006 Emerson Electric Co
27. duct within thirty 30 days of shipment of any replacement parts components or products if applicable and only if Liebert s inspection discloses the claimed defect and the returned product shows no signs of treatment or use which would void the coverage of this Warranty All defective products and component parts replaced under this Warranty become the property of Liebert arra of nen H It is Liebert s practice consistent with its desire to remcdy Warranty defects in the most prompt and effective manner possible to cooperate with and utilize the services of component manufacturers and their authorized representatives in the performance of work to correct defects in the product components Accordingly Liebert may utilize third parties in the performance of Warranty work including repair or replacement hereunder where in Liebert s ophion such work can be performed in less time with less expense or incloser proximity to the Liebert product Installation Operation and Maintenance Manual 27 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Items Not Covered By Warranty THIS WARRANTY DOES NOT COVER DAMAGE OR DEFECT CAUSED BY misuse improper application wrong or inadequate electrical current or connection negligence inappropriate on site operating conditions corrosive atmosphere repair by non Liebert designated personnel accident in transit tampering alterations a change in location or operating use exposure to the elemen
28. e requires replacement an audible alarm is activated to draw attention to the fact that repair service is required to restore the system to normal operation An audible alarm disable is provided to silence the alarm The system will automatically reset itself after repair The audible alarm switch and Service LED can be tested by activating the Test switch on the system monitor panel For information on the AccuVar Series Alarm see page 16 Liebert TVSS Units 51 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems Troubleshooting Servicing Maintenance Troubleshooting If status failure indication occurs or Form C relay has changed states a qualified electrician shall first determine if the systems voltage and proper phasing exists If the SPD remains in an alarm condition once the electrician is satisfied that the electrical system and its connections are normal the unit should be repaired At this point consult the factory having available the following information Unit identification number refers to the model and serial numbers detailed on the data label and is located on the front or upper left hinge side of the enclosure Nature of problem including status of all status indicators and alarms Servicing ONLY QUALIFIED PERSONNEL SHOULD PERFORM MAINTENANCE ON THE SYSTEM HAZARDOUS VOLTAGES ARE PRESENT INSIDE THE UNIT DURING NORMAL OPERATIONS ELECTRICAL SAFETY PRE CAUTIONS MUST BE FO
29. ee Phase Delta 48 0 20 0 FxxxY4000 Three Phase Wye 48 0 20 0 NOTE Consult factory for special instructions on caseless and switchgear models Installation Operation and Maintenance Manual 17 Liebert TVSS Units SL 22085 Rev 2 11 2006 800A 1200A 2000A 4000A 9 Liebert Surge Suppression Systems Type SS Series Phase L1 Phase L2 Disconnect Main Breaker For Panel Neutral Buss PhaseA Phase B Phase C Disconnect Main Breaker For Service Panel For Loads to be Dedicated Disconnect Optional Polycarbonate Window Type SS Series Dimensions Inches Suggested Allowable sepes WIRES AWG Range renange Phase 32 1332 65 1475 10 032 26 soa m 5 175 14 2 0 Phase 1932 1732 96 1875 12 80A 4 5 aao Installation Operation and Maintenance Manual 18 Liebert TVSS Units SL 22085 Rev 2 11 2006 0 Liebert Surge Suppression Systems Type LM Series i jase Service Panel for Phas Loads to be Protected Disconnect Main Breaker for Panel Dedicated Neutral Buss C Disconnect Optional Ground Buss Recommended Wire Entrance 1 840 Max Suggested Allowable jm eed Wire Size Breaker iras AWG Range 15A 100A 14 2 Suggested Breaker Size Installation Operation and Maintenance Manual 19 Liebert TVSS Units SL 22085 Rev 2
30. est a return authorization number User shall ship the product with proof of purchase to Liebert freight prepaid Liebert products shipped to Liebert without a return authorization number will be refused and returned freight collect to User at User s expense Liebert products shipped by User to Liebert which have incurred freight damage due to User s improper packaging of the product will not be covered by this Warranty and any repairs or replacement parts components or products needed will be invoiced in the full current price amount and returned freight collect to User Subject to the limitations specified herein Liebert will repair or replace at its option without charge for Liebert labor or materials subsequent to its inspection F O B Liebert s facility the Liebert product warranted hereunder which does not conform to the Warranty Replacement parts components or products shipped to User prior to Liebert s receipt and inspection of the product claimed to be defective shall be invoiced in the full current price amount and shipped freight collect F O B Liebert s facility Warranty coverage will be extended only after Liebert s receipt of the claimed defective product within thirty 30 days of shipment of any replacement parts components or products if applicable and only if Liebert s inspection discloses the claimed defect and the returned product shows no signs of treatment or use which would void the coverage of this Warranty
31. ffset Conduit Nipple Dedicated Disconnect Ground Buss 5 700 Unit is equipped with Summary Alarm Contacts The 18 wires are designated as follows Unit is supplied from the factory with a minimum length of 18 of 12 wire for connection It is REQUIRED that a 30A circuit breaker or less be used for installation YELLOW Normally Open ORANGE COMMON BLUE Normally Closed Installation Operation and Maintenance Manual 21 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems PanelGuard Series Type LPGE Customer Supplied PanelBoard Uninsulated Ground Bar 3 Pole Conduit e Amp Collar Breaker 0 Liebert Slots for Sliding Trim S To Ensure Summary Alarm Supplied Contacts Inside LPGE Unit Module Remove Cover for Access Installation Operation and Maintenance Manual 22 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems Example Installations Installation Operation and Maintenance Manual 23 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems SURGE SUPPRESSION 3t 3 Installation Operation and Maintenance Manual 24 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems Limited Warranty This Warranty is given ONLY to purchasers who buy for commercial or industrial use in the ordinary course of each purchaser
32. hereof This Warranty represents the entire agreement between Liebert and User with respect to the subject matter herein and supersedes all prior or contemporaneous oral or written communications representations understandings or agreements relating to this subject Installation Operation and Maintenance Manual 26 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems Limited Warranty This Warranty is given ONLY to purchasers who buy for commercial or industrial use in the ordinary course of each purchaser s business eneral Liebert Corporation products and systems are in our opinion the finest available We take pride in our products and are pleased that you have chosen them Under certain circumstances we offer with our products the following Five Year Warranty Against Defects in Material and Workmanship Please read your Warranty carefully This Warranty sets forth our responsibilities in the unlikely event of defect and tells you how to obtain performance under this Warranty YEAR D WA Y AGAINST DEFE NDW HIP LIEBERT PRODUCTS COVERED PanelGuard Extension LM Series Transient Voltage Surge Suppressors AccuGuide Cable and PowerSure Panel Transient Voltage Surge Suppressors Terms of Warranty As provided herein the Liebert product is warranted to be free of defects in material and workmanship for a period of five 5 years from the date of product shipment from Liebert The shipment date
33. ked G of the SPD using the wire range listed in the table on page 12 in accordance with the National Electric Code NEC Article 285 and all local codes To yield the best performance of the SPD within the electrical distribution system avoid sharp bends 10 Connection to the Form C contacts shall be with 18 22 AWG Contacts are rated 5 amps at 250 maximum with a power factor of 1 0 11 Apply power The surge protector is fully operational when the GREEN LEDs on the modules and the front door of enclosure are illuminated If the GREEN LEDs are extinguished or the RED LED is illuminated check to ensure that power is applied to the SPD If an abnormal indication is present remove power to the SPD and contact Liebert Emerson Network Power Surge Protection at 1 800 288 6169 or 1 607 724 2484 12 Periodically monitor the status of the LEDs Reduced protection exists if the GREEN LEDs are extinguished or the RED LED is illuminated Please contact Liebert Emerson Network Power Surge Protection at 1 800 288 6169 or 1 607 724 2484 13 The protection modules in these SPDs are replaceable contact Liebert Emerson Network Power Surge Protection for replacement Installation Operation and Maintenance Manual 10 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems Typical Series Connections for Wye 4 Wire Ground or Single Phase 3 Wire Ground System Liebert Active Tracking Fi
34. ker is not necessary for over current protection for most units LPL Units require a 30A or less circuit breaker However it is recommended that the SPD be connected in series with a circuit breaker denoted in the tables below also indicated on the Dimensional Information pages in this manual The SPD shall be connected in accordance with all national and local electrical codes 5 Connect black wires line or phase marked L1 A L2 B or L3 C the white wire neutral marked N and the green wire ground marked G of the SPD using the wire range listed below To yield the best performance of the SPD within the electrical distribution system keep all conductors as short as possible and avoid sharp bends If the SPD model is a Wye configured unit 4W G and a Neutral connection is not available please contact factory Allowable Range Factory Suggested Size Circuit Breaker Size Connection Wire Size ENIM connection With Disconnect Without Disconnect Size Wire Size ith Di 5016 5025 5A 150A 14 10 60 Amp 15A 175A 4 2 0 MEME 5032 5050 15A 175A _ 75A 15A 175A 75 14 20 51060 51075 4 2 0 4 2 0 4 1 0 4 HE 111 250 60 Amp Hxoox222 320kA 15 175 4 2 0 Hybrid Advantage 10000222 320 _ ybrii antage H 33 400kA TSA 175 15A 175A 4 2 0 14 2 0 80 Amp 444 750kA 5A 175A 4 2 0 80 Amp Typessseries AllUnits 5 175 14210
35. lter System INPUT OUTPUT LN s 1 8 Neutral N To required irre Ground sedis Typical Series Connections for Delta 3 Wire Ground System Liebert Active Tracking Filter System INPUT OUTPUT br Erotected Ground D Transient q oads TERMINAL WIRE SIZE RANGE FILTER CONTINUOUS PHASE AND TRANSIENT SAFETY CURRENT RATING NEUTRAL TERMINALS GROUND TERMINAL GROUND TERMINAL 30 100 A amp 14 2 0 1 14 2 0 5 14 4 4 225 6 250 kcmil 1 14 2 0 5 10 1 0 4 400 A 6 250 kcmil 2 6 250 kcmil 2 6 250 kcmil 4 800A 2 75 x 50 Cu Busbar 3 6 250 kcmil 2 6 250 kcmil 4 1200A 2x 6 0 x 25 Cu Busbar 3 6 250 kcmil 2 6 250 kcmil 4 2000A 6 0 x 25 Cu Busbar 3 6 250 kcmil 2 6 250 kcmil 2 4000 A 5x 6 0 x 25 Cu Busbar 3 6 250 kcmil 2 6 250 kcmil 2 NOTES 1 Single lug with single connection for Input and Output 2 Single lug with dual connection for Input and Output 3 Units must be installed with Busbar s only Wire lugs are not U L approved 4 Single lug with single connection 5 Single lug with dual connection Installation Operation and Maintenance Manual Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems Liebert PanelGuard Series Type LPGE Surge Protective Device SPD Installation Instructions 1 Insure that all power is removed befo
36. ormal conditions the green LED is illuminated and the red Service LED is extinguished If the surge SPD module requires replacement the green OK LED is turned off and the red Service LED illuminated Summary Alarm Contact if applicable Summary alarm Form C 1 N O and 1 N C relay contacts may be provided for remote indication of the failed surge SPD module Contacts are rated 5 amps at 250 VAC maximum with a power factor of 1 0 For units with Summary Alarm Contacts access to the contacts are typically provided via contact terminals located on the printed circuit board mounted on the inside of the unit s cover Transient Counter if applicable Transient counters are provided for transient voltage surge monitoring The counter totalizes surges monitored since the last counter reset The transient counter monitors line transient voltages The circuit counts all surges that deviate from the line sine wave The factory setting is 30 over nominal line voltage Other settings include 50 7075 and 100 Swell Counter if applicable The swell counter monitors line to line amp line to neutral voltages It is factory set to record whenever the peak voltage on any normal mode exceeds the nominal voltage of the TVSS for more than 10ms This counter records temporary line over voltages that may result from utility switching line regulation problems etc Audible Alarm if applicable If the surge SPD modul
37. ors leave the enclosure or vault in which the tap is made the rating of the over current device on the line side of the tap conductors shall not exceed 10 times the Ampacity of the tap conductor 2 Taps Not Over 7 5 m 25 ft Long Where the length of the tap conductors does not exceed 7 5 m 25 ft and the tap conductors comply with all of the following 1 The Ampacity of the tap conductors is not less than one third of the rating of the over current device protecting the feeder conductors 75 Amp maximum in our case 2 The tap conductors terminate in a single circuit breaker or a single set of fuses that will limit the load to the Ampacity of the tap conductors This device shall be permitted to supply any number of additional over current devices on its load side 3 The tap conductors are suitably protected from physical damage or are enclosed in a raceway 3 Taps Supplying a Transformer Not Applicable 4 Taps Over 7 5 m 25 ft Long Not Applicable 5 Outside Taps of Unlimited Length Not Applicable Flexible liquid tight non metallic conduit in lengths greater than six feet must be installed in accordance with NEC 351 27 Installation Operation and Maintenance Manual 13 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems Connection The AccuGuide assembly is provided in standard lengths of 5 8 10 12 15 and 20 feet Each end of the assembly will include an additional five feet of 10 8
38. racking Filter Series Type F 2 usess repere rrr ERE Ra EE COUPER PP uda E dee xu Ries 17 SSSeries SS iis epe ce ab E REY 18 EMiSeries Type EE SE EE Henin weer wale 19 PowerSure Medium Exposure Series Type memes e nen 20 PowerSure Low Exposure Series Type 4 52 eere rre kr rr RR erre Ex xa y par ELE Y ee eee ee ee ee 21 PanelGuard Series re ER RR FE DURS See USE ERE EE MEME 22 EXAMPLE INSTALLATIONS rhe a pre RR Y CREAR Yr a eR ERE 23 WARRANTY INFORMATION Rer RR Cae eraser LOS E ERR ER 25 Year noe rid ee PAR GU E PLN RODA Ne sins Ia 25 SAGEIBIEIERISRSEERTIEEC ID LLL LLL LL S TII LE 27 Installation Operation and Maintenance Manual 1 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems INSTALLATION INSTRUCTIONS The Liebert Surge Protective Devices SPDs are high quality high energy surge current diversion systems designed to protect sensitive equipment from damaging transient voltage surges Proper installation is required for maximum system performance The installer should perform the following steps to assure a quality installation The entire installation manual
39. re beginning installation A qualified licensed electrician shall install all electrical connections 2 The unit is provided in a NEMA 1 rated industrial use enclosure and should be installed in areas only appropriate for NEMA 1 3 The unitis to be wall mounted in an area where sufficient access and working space around the cabinet can be assured See NEC Section 110 16 Position the SPD opposite the incoming feed to the panelboard For example if the panelboard is supplied through the top of its enclosure mount the SPD at the bottom of the panelboard 4 Knockouts for connection of the suppressor to the panelboard back box are provided on top bottom and sides of the unit s enclosure The diameters of the knockouts vary to accommodate conduit collar diameters of 1 2 in to 1 1 4 in The proper size busing diameter and length must be selected to protect the conductors as they transition from the SPD to the panelboard conductor and to maintain the cosmetic integrity of the Liebert LPGE Series Surge Protection Device 5 When connecting the SPD to the panelboard it is important that the panelboards interior and the SPD are protected from any metal shavings which may result An inspection and cleaning of the LPGE should be performed before applying power 6 Representative samples of this product have been investigated by Underwriters Laboratories Incorporated to withstand without exposing live circuits or components at system voltages and f
40. romsitetosite Inspections for failed surge modules using available diagnostics should be done routinely weekly or monthly Liebert TVSS Units SL 22085 Rev 2 11 2006 0 Liebert Surge Suppression Systems Typical Parallel Installations Surge Protective Devices SPD Interceptor Il Series Hybrid Advantage Series Type SS Series Type LM Series Type SI TypeH Sant tiiv son _ PowerSure Medium Exposure Series AccuVar Series PowerSure Low Exposure Series Type LPM Type ACV amp All Type LPL Suse Le Installation Instructions 1 Insure that all power is removed before beginning installation A qualified licensed electrician shall install all electrical connections 2 The SPD is provided in the enclosure type listed below NEMA 12 enclosures are suitable for use in indoor installations NEMA NEMA 4 or NEMA 4X enclosures are suitable for use in indoor or outdoor installations SPD Standard Enclosure Optional Enclosures SPD Standard Enclosure Optional Enclosures Type SI NEMA 4 NEMA 4X Type ACV All NEMA 4X N A Type H NEMA 12 4 4X Type LPM NEMA 12 NEMA 3R 4 4X Type SS NEMA 4X N A Type LPL ABS Plastic 94V 0 NEMA 1 Type LM NEMA 12 4 4X 3 Determine where the SPD is to be mounted allowing for minimum length of wire between itself and the input power terminals of the service panel Punch or cut the proper hole size in the side of the SPD closest to the knockou
41. t to be utilized in the service panel Drill mounting holes in wall at location picked for SPD next to service panel using mounting dimensions shown in the tables on the Dimensional Information pages in this manual Mount surge suppressor using the hardware listed SPD Mounting Hardware SPD Mounting Hardware Type SI Page 15 3 8 Type ACV AII Page 16 8 Type H Page 16 3 8 Type LPM Page 20 10 Type SS Page 18 1 4 Type LPL Page 21 6 Type LM Page 19 1 4 4 The SPD has obtained the short circuit current rating shown below SPD Short Circuit Current Rating SPD Short Circuit Current Rating Type SI 200 000 Symmetrical Amperes Type ACV All 200 000 Symmetrical Amperes Type H 200 000 Symmetrical Amperes Type LPM 65 000 Symmetrical Amperes Type SS 65 000 Symmetrical Amperes Type LPL 14 000 Symmetrical Amperes Type LM 200 000 Symmetrical Amperes Circuit Ampacity Limitations Representative samples of these products have been investigated by Underwriters Laboratories Incorporated to withstand without exposing live circuits or components at system voltages and fault currents of up to the rating shown above as described in the Standard for Safety Transient Voltage Surge Suppressor TVSS Standard 1449 Second Edition dated August 15 1996 Installation Operation and Maintenance Manual 8 Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert Surge Suppression Systems An external circuit brea
42. tected Loads Neutral Rotary Disconnect Phase s Transient Ground Protected Safety Panel Wire should be Ground less than 5 feet and straight as possible Installation Operation and Maintenance Manual 5 Liebert Surge Protective Device Liebert TVSS Units SL 22085 Rev 2 11 2006 9 Liebert System Grounding and Bonding The performance and safety of any SPD system is dependent on proper grounding and bonding Grounding is required for safety Correct implementation also enhances equipment performance Incorrect grounding can reduce or impede the SPD s operation All electrical circuits to the SPD must include an equipment grounding conductor as required by the NEC and local codes An insulated grounding conductoris required in addition to any metallic raceway which may be used as a grounding conductor For parallel connected SPDs the grounding conductor should be the same wire size as the associated power conductors Grounding conductors must be routed with the associated power conductors in the same raceway conduit When metallic raceways are used adequate electrical continuity must be maintained at all raceway connections particularly raceway terminations to the electrical enclosures The use of isolating bushings or other means to interrupt a metallic conduit run is a potential safety hazard and is not recommended Gro
43. tion for whom the Liebert product specified herein is originally installed for use the User in the fifty United States excluding territories or Canada This Warranty is not transferable or assignable without the prior written permission of Liebert Assignment of Warranties Liebert assigns to User any warranties which are made by manufacturers and suppliers of components of the Liebert product and which are assignable but Liebert makes NO REPRESENTATIONS as to the effectiveness or extent of such warranties assumes NO RESPONSIBILITY for any matters which may be warranted by such manufacturers or suppliers and extends no coverage under this warranty to such components Drawings Descriptions Liebert warrants for the period and on the terms of the Warranty set forth herein that the Liebert product will conform to the certified drawings if any applicable thereto to Liebert s final invoices and to applicable Liebert product brochures and manuals current as of the date of product shipment Descriptions Liebert does not control the installation and use of any Liebert product Accordingly it is understood that the Descriptions are NOT WARRANTIES OF PERFORMANCE and NOT WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE Obtaining Performance Under This Warranty Within a reasonable time but in no case to exceed thirty 30 days after User s discovery of a defect User shall contact Liebert at 1 800 LIEBERT 543 2378 and requ
44. ts Acts of God theft or installation contrary to Liebert s recommendations or specifications or in any event if the Liebert serial number has been altered defaced or removed Notwithstanding the foregoing the following Acts of God are covered lightning induced surges which are transients spikes or other sub cycle discontinuous events impinging on normally applied voltage as defined by reference data in the latest version of IEEE C62 41 and Liebert product performance specifications THIS WARRANTY DOES NOT COVER shipping costs installation costs circuit breaker resetting or maintenance or service items and further except as provided herein does NOT include labor costs or transportation charges arising from the replacement of the Liebert product or any part thereof or charges to remove a reinstall same at any premises of the User THIS WARRANTY DOES NOT COVER DAMAGE OR DEFECT CAUSED BY use of the Liebert product in combination with any electrical or electronic components circuits systems assemblies or other materials not furnished by Liebert Liebert does NOT warrant the suitability for use or the results ofthe Liebert product in combination with the products of others THE PRODUCTS LISTED IN THIS WARRANTY ARE NOT DESIGNED FOR USE IN THE FOLLOWING APPLICATIONS i ANY NUCLEAR OR RELATED APPLICATIONS AND ii LIFE SUPPORT AND PATIENT CONNECTED AND APPLIED MEDICAL AND DENTAL APPLICATIONS REPAIR OR REPLACEMENT OF A DEFECTIVE PRODUC
45. uit as practical to minimize interconnecting wiring length To reduce the wiring impedance to surge currents it is recommended thatthe phase neutral if required and ground conductors are twisted together and routed in the same raceway conduit Avoid any sharp bends in the conductors Wire Sizing With parallel connection the size of the wiring to the SPD unit is independent of the protected circuit s ampacity For suggested wire size refer to individual product sheet NEC Article 285 21 B requires surge suppressor connecting conductors to be at least 14 copper or 12 aluminum Overcurrent Protection The SPD unit conducts practically no current under normal operation and only conducts very short duration transient surge currents Installation Operation and Maintenance Manual The following is from the National Electric Code 2002 Edition 285 21 Connection Where a TVSS is installed it shall be connected as follows A Location 1 Service Supplied Building or Structure The transient voltage surge suppressor shall be connected on the load side of a service disconnect overcurrent device required in 230 91 2 Feeder Supplied Building or Structure The transient voltage surge suppressor shall be connected on the load side of the first overcurrent device at the building or structure Exception to 1 and 2 Where the TVSS is also listed as a surge arrestor the connection shall be as permitted by Article
46. unding Electrode Surge protective devices do not discharge all surges to ground earth Surge protective devices divert the surge current back to its source to complete the electrical circuit In the case of lightning whose potential is developed with respect to the earth the SPD diverts the surge current to the grounding electrode earth connection However for most transient surges that are developed by switching loads the SPD diverts the surge current back to its source without involving the grounding electrode For proper SPD performance the service entrance grounding electrode system must comply with the NEC by having all available electrodes building steel metal water pipe driven rods concrete encased electrodes etc properly bonded together and connected to the power system grounding The use of a separate grounding electrode to ground the SPD defeatsthe effectiveness ofthe SPD is a potential safety hazard may cause equipment damage is an NEC violation reference NEC 250 51 and 250 54 and is not recommended Installation Operation and Maintenance Manual Surge Suppression Systems A CAUTION FOR PROPER AND SAFE OPERATION THE NEUTRAL IF PROVIDED MUST BE RELIABLY CONNECTED TO THE NEUTRAL OF THE SOURCE FAILURE TO PROVIDE A RELIABLE NEUTRAL CONNECTION MAY RESULT IN MODULE FAILURE SPD Monitoring External Status Indicators These indicators provide a summary of the status of the surge SPD module For n
47. using 3 8 16 hardware or equivalent 5 Units up to 225 amps are suitable for short circuit current ratings up to 25 000 amps For short circuit currents up to 50 000 amps Class RK5 fuses sized up to 125 of the filter s continuous current rating are required Units rated at 400 to 800 amps are suitable for available symmetrical short circuit currents up to 50 000 amps For short circuit currents up to 100 000 amps Class Fuses sized up to 125 of the filter s continuous current rating are required Units 1200 amps and above are suitable for available symmetrical short circuit currents up to 200 000 amps 6 For best performance keep input and output wiring separated as much as practical to eliminate input to output coupling of noise and transients Do not route input and output wiring in the same raceway If practical terminate input and output raceways conduits at opposite ends of the active tracking filter enclosure input near the top and output near the bottom 7 The Liebert Active Tracking Filter System is wired in line in series with the protected load s See Figures on the following page 8 Terminals are provided inside the Liebert Active Tracking Filter System for the line phase neutral if used transient ground and equipment safety ground connections See page 11 for terminal wire size ranges 9 Connect black wires line or phase marked L1 A L2 B or L3 C the white wire neutral marked and the green wire ground mar
48. ve humidity of 0 to 95 non condensing The unit is provided in an industrial use enclosure which is dust tight and drip tight and should not be installed in areas with excessive dust corrosive vapors flammable materials or explosive atmospheres Audible Noise The audible noise of the unit is less than 40 dB at 5 feet which allows its placement within almost any room if desired Service Clearances Service clearance is needed for units with hinged doors on the front that are capable of being opened Thirty six inches 36 in 914 mm minimum is recommended Installation Operation and Maintenance Manual EQUIPMENT PERFORMANCE To maximize system performance locate unit as close as possible to protected circuit and keep inter connecting wiring less than 5 ft For optimum transient surge protection coordinated surge suppression should be applied at the service entrance and all other electrical connections to the building telephone CATV etc at known surge generating loads within the building large motors arc welders switched capacitors etc as well as at sensitive electronic loads such as computers electronic appliances solid state motor drives etc For interconnected electronicloads suchas by way of data cabling transient surge suppression should also be applied to the interconnecting wiring data cables Mounting Unit is intended to be wall mounted Refer to individual instruction sheet or unit

Liebert AccuVar User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents