LG LRE3023SB User's Manual
Contents
1. 6 PREPARE TO INSTALL THE RANGE INSTALLATION DRAWINGS O NOTE SAVE FOR THE USE OF THE LOCAL ELECTRICAL INSPECTOR CLEARANCES AND DIMENSIONS Figure 1 To install range refer to the following Figure 1 For installation in CANADA a Free standing range is not to be installed closer than 15 32 12mm from any adjacent surface N CAUTION ACAUTION e Make sure that the wall covering countertop e Cabinet storage space located above the and cabinets around the range can with surface units should be avoided stand the heat up to 194 F generated by e Install a range hood that projects horizontally the range a minimum of 5 inches beyond the bottom Discoloration delamination or melting may of the cabinets if cabinet storage is to be occur provided This range has been designed to comply with The risk of burns or fire by reaching over the the maximum allowable wood cabinet tem heated surface elements can be reduced peratures of 194 F 3 7 6cm 24 60 9cm 3 7 6cm 25 N orma Hi 63 5cm counter Acceptable top depth a electrical i o outlet area E 76 2cm l l 30 76 2cm Minimum i 6 15 2cm p 36 Count o SF Wy ee 91 4cm top height 15 ee S 38 1cm J Cabinet opening 7 o OoOo y O n 36 91 4cm 30 76 2cm gt A 30 76 2 cm For U S2. LG Life s Good INSTALLATION MANUAL ELECTRIC RANGE Please read these instructions thoroughly before installing and operating the range LRE O ool LRESOZ 35l LRE30255B LRE 9D LRE3025SW LRE3023SW i ee MN Printed on 100 Recycled Paper MFL57205804 www lg com m Z O m T T TONVdSS 2 TABLE OF CONTENTS TABLE OF CONTENTS SAFETY Before You Begin Important Safety Instructions mw w W Prepare to Install the Range PREPARE TO INSTALL RANGE rn Oo Installation Drawings Ni ELECTRICAL CONNECTIONS Electrical Connection Requirements Connect Range Cord 3 Wire Connection With a Power Supply Cord 4 Wire Connection With a Power Supply Cord 3 Wire Connection Conduit 4 Wire Connection Conduit O OO 0 ON N 11 INSTALL THE RANGE 11 Anti Tip Device Installation 11 Final Installation SAFETY 3 BEFORE YOU BEGIN Remove all tape and packing materials before using the range m Z T L Dispose of all plastic bags after unpacking the range Never allow children to play with packing materials You can download the installation and owner s manual at http www lg com IMPORTANT SAFETY INSTRUCTIONS Read and follow all instructions before using your oven to prevent the risk of fire electric shock personal injury or damage when using the range This guide does not cover all possible c
3. 8 9 cm 3 wire 1 3 8 2 5cm 0 9 cm 1 3 g 2 5cm 0 9 cm l at Conduit 7 connection plate 31 2 8 9 cm 3 wire FIg URE 10 Second install conduit as shown in Figure 6 For conduit installations after purchasing a strain relief insert it in the conduit hole 1 s Then install the conduit through the body of strain relief and fasten the Strain relief with its ring Reinstall the bracket For conduit connections If the wire in the conduit is copper it must be 8 or 10 AWG wiring If the wire in the conduit is aluminum it must be 6 or 8 AWG wiring 1 Loosen the lower 3 screws from the terminal block Refer to Figure 11 2 Insert the bare wire white neutral end through the center terminal block opening Do not remove ground strap connections 3 Insert the two side bare wire ends into the lower left and the lower right terminal block opening Tighten the 3 screws securely into the terminal block approximately 35 50 IN LB 4 Refer to page 11 3 wire connection Red Terminal Conduit connection plate FIgURE 11 m Z T L 10 ELECTRICAL CONNECTIONS 4 WIRE CONNECTION CONDUIT 7 Follow the instructions under Install the conduit as follows on page 8 to correctly install the strain relief DO NOT install the conduit without a strain relief Loosen the 2 lower left and right screws from the terminal block Refer to Figure 12
4. Remove the lower 2 center screws Remove ground strap and discard as shown in Figure 12 Do not discard any screws Attach the ground bare wire end to range frame and secure it in place with the ground screw Refer to figure 12 Insert the bare wire white neutral end through the center terminal block opening Insert the two side bare wire ends into the left and the right terminal block opening Tighten the 3 screws securely into the terminal block approximately 35 50 IN LB Refer to page 11 4 wire connection Black White Red Terminal i y liae a Pek ellos AT iy ft Wire gt 3 Ground 8 7 strap T gt Remove ground strap and discard Conduit connection plate I I I I I FIgURE 12 INSTALL THE RANGE 1 Replace the access cover on the back of the range To replace the wire cover insert the two tabs into the openings located below the opening and tighten the three screws J Access cover ANTI TIP DEVICE INSTALLATION A WARNING e Any person should not step or sit on the oven door You should install the Anti Tip Brackets supplied with the range The range could be tipped and injury might result from spilled hot liquid food or the range itself Ifthe range is pulled away from the wall for cleaning service or any other reason ensure that the Anti Tip Device is properl
5. A 30 76 2 cm 31 78 7 cm For CANADA FIgURE 1 FIgURE 2 MINIMUM DIMENSIONS Figure 2 30 76 2 cm minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet or 24 60 9 cm minimum when bottom of wood or metal cabinet is protected by not less than 1 4 6 4 cm flame retardant millboard covered with not less than no 28 MSG sheet steel 0 015 0 381 mm stainless steel 0 024 0 610 mm aluminum or 0 020 0 508 mm copper 15 38 1 cm minimum between countertop and adjacent cabinet bottom ELECTRICAL CONNECTIONS T ELECTRICAL CONNECTION REQUIREMENTS This appliance must be installed and grounded on a branch circuit by a qualified technician in accordance with the National Electrical code ANSI NFPA NO 70 latest edition All wiring should conform to Local and NEC This range requires a single phase 3 wire A C 120 208V or 120 240V 60Hz electrical system Use only a 3 conductor or a 4 conductor UL listed range cord with closed loop terminals open end spade lugs with upturned ends or similar termination DO NOT install the power cord without a strain relief A range cord rated at 40 amps with 120 240 minimum volt range is required If a 50 amp range cord is used it should be marked for use with 138 diameter connection openings This appliance may be connected by means of conduit or power cord If conduit is being used go to page 7 for 3 wire conduit
6. 7 7 5 e minal block Power cord outlet 2 a fp Q Cord Conduit connection a Drawer body plate FIgURE 4 Access cover The Cord Conduit connection plate is used for the installation of power cord or conduit For power cord install it with the connection plate as INSTALLED For conduit remove the connection plate located below the rear of the drawer body and use the conduit hole 1 1 8 instead of power cord hole 1 3 8 Refer to Figure 5 and 6 13 s Cord 1 s Conduit Remove the Conduit connection plate FIg URE 5 Cord conduit connection Strain relief Conduit Assemble the strain relief hole Cord Strain relief Reinstall the Cord Conduit connection plate FIg URE 6 m Z 9 T L 8 ELECTRICAL CONNECTIONS 3 WIRE CONNECTION WITH A POWER SUPPLY CORD A WARNING e The middle neutral or ground wire of a 3 wire power cord or a 3 wire conduit has to be connected to the middle post of the main terminal block The remaining two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block Failure to do so can result in electrical shock severe personal injury or death Install the power cord as follows For pow
7. connections or page 8 for 4 wire conduit connections A WARNING e New branch circuit installations 1996 NEC for mobile homes recreational vehicles and installations where local codes do not allow grounding through the neutral wire require a 4 conductor UL listed range cord or 4 wire conduit connection e Power supply cord and plug should not be modified If it will not fit the outlet have a proper outlet Installed by a qualified electrician e Using an extension cord to connect the power is prohibited The way to connect the power cord and plug directly is strongly recommended e Electrical ground is required on this appliance e You should make sure that the power cord is not pinched by the range or heavy objects Failure to do so can result in serious burns or electrical shock Specified power supply cord kit rating Range rating watts Specified Diameter inches of Range rating of power connection Opening 120 240 volts 120 208 volts supply cord kit Power cord Conduit 3 wire 3 wire amperes 8 750 16 500 7 801 12 500 40 or 50A 1 3 8 1 1 3 16 501 22 500 12 501 18 500 50 13 4 13 8 3 4 Wire electrical wall Receptacle a 4 Wire receptacle 14 50R 3 Wire receptacle 10 50R FIg URE 3 CONNECT RANGE CORD The Rear Access cover must be removed Loosen the three screws with a screwdriver The terminal block will then be accessible e
8. ction block The 4th ground wire must be connected to the frame of the range with the ground screw Failure to do so can result in electrical shock severe personal injury or death Install the power cord as follows For power cord installations Hook the strain relief over the power cord hole 1 located below the rear of lower oven Insert the power cord through the strain relief and tighten it Refer to Figure 7 DO NOT install the power cord without a strain relief 1 Remove the lower 3 screws from the terminal block and retain them Refer to Figure 9 2 Remove ground strap and discard as show in in Figure 9 3 Insert the ground screw into the power cord ground wire terminal ring and secure it to the range frame 4 Insert the 3 screws through each power cord terminal ring and into the lower terminals of the terminal block Make sure that the center wire white neutral is connected to the center lower position of the terminal block 5 Tighten 3 screws securely into the terminal block 4 wire connection Ground strap Remove ground strap and discard Ground screw Conduit connection plate FIgURE 9 3 WIRE CONNECTION CONDUIT Install the conduit as follows Remove the Conduit connection plate from the rear of lower oven and rotate it as shown in Figure 5 The conduit hole 1 s must be used First prepare the conduit wires as shown in Figure 10 4 wire 31 2
9. e properly installed and the range will not tip forward Turn on electrical power Check the range for proper operation as described in owner s manual m Z 9 T IL 12 MEMO LG Life s Good LG Customer Information Center For inquires or comments visit www lg com or call 1 800 243 0000 USA Consumer User 1 888 542 2623 CANADA Register your product Online Printed in Korea
10. er cord installations Hook the strain relief over the power cord hole 13 s located below the rear of lower oven Insert the power cord through the strain relief and tighten it Refer to Figure 7 DO NOT install the power cord without a strain relief 1 Remove the lower 3 screws from the terminal block and retain them Refer to Figure 8 2 Insert the 3 screws through each power cord terminal ring and into the lower terminals of the terminal block Make sure that the center wire white neutral is connected to the center lower position of the terminal block 3 Tighten 3 screws securely into the terminal block Do not remove the ground strap connections 4 Refer to page 11 Separate Strain Relief before installation Assemble the strain relief NG to the 1 s opening in Conduit connection plate ie 3 connection plate Conduit connection plate FIg URE 8 o wren ELECTRICAL CONNECTIONS 9 4 WIRE CONNECTION WITH A POWER SUPPLY CORD A WARNING e Only a 4 conductor power supply cord kit rated 120 240 volts 50 amperes and marked for use with ranges with closed loop connectors or open end spade lugs with upturned ends shall be used The middle neutral wire of the power cord or 4 wire conduit has to be connected to the middle post of the main terminal block The other two wires of the power cord or conduit have to be connected to the outside posts of the main terminal conne
11. n cover covering the rear of oven Failure to do so can result in serious damage to power cord The damage causes serious burns and electric shock The middle neutral or ground wire of a 3 wire power cord or a 3 wire conduit has to be connected to the middle post of the main terminal block The remaining two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block Failure to do so can result in electrical shock severe personal injury or death Only a 4 conductor power supply cord kit rated 120 240 volts 50 amperes and marked for use with ranges with closed loop connectors or open end spade lugs with upturned ends shall be used The middle neutral wire of the power cord or 4 wire conduit has to be connected to the middle post of the main terminal block The other two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block The 4th ground wire must be connected to the frame of the range with the ground screw Failure to do so can result in electrical shock severe personal injury or death A CAUTION e You should put on gloves during the installation procedure Failure to do so can result in bodily injury e You should make sure that the wall covering countertop and cabinets around the range can withstand the heat up to 194 F generated by the range Discoloration delamination or melting may occur This
12. onditions that may occur For further assistance contact your service agent or manufacturer you and others All safety messages will follow the safety alert symbol with either the word WARNING or This is the safety alert symbol This symbol alerts you to potential hazards that can cause personal injury to CAUTION AWARNING This symbol will alert you to hazards or unsafe practices which could cause serious bodily harm or death Z CAUTION This symbol will alert you to hazards or unsafe practices which could cause bodily injury or property damage A WARNING e The information in this manual should be followed exactly A fire or electrical shock may result causing property damage personal injury or death Do not step or sit on the oven door Install the Anti Tip Brackets supplied with the range The range could be tipped and injury might result from spilled hot liquid food or the range itself If the range is pulled away from the wall for cleaning service or any other reason ensure that the Anti Tip de vice is properly reengaged when the range is pushed back against the wall Install the Anti Tip Brackets Achild or adult can be killed when the range is tipped 1 According to the Anti Tip Bracket Template install 2 Anti Tip Brackets to the floor and wall Anti Tips will fasten the range by holding the range s 2 legs of the rear side and the Anti Tip Bracket Template lets you know proper locati
13. ons of Anti Tip Brackets easily 2 Engage the range to the Anti Tip Brackets by putting the range s 2 legs into each Anti Tip Bracket 3 Re engage the Anti Tip Brackets if you can move the range except for range s front direction 4 See installation instructions for details refer to the page 11 Failure to do so can result in death or serious burns to children or adults You should use two or more people to move and install range Excessive Weight Hazard Failure to do so can result in back or other injury You never pull or push any handles of door to move and install range Failure to do so can result in serious damage to the door of the range New branch circuit installations 1996 NEC for mobile homes recreational vehicles and installations where local codes do not allow grounding through the neutral wire require a 4 conductor UL listed range cord or 4 wire conduit connection 4 SAFETY A WARNING Power supply cord and plug should not be modified If it will not fit the outlet have a proper outlet Installed by a qualified electrician Using an extension cord to connect the power is prohibited The way to connect the power cord and plug directly is strongly recommended Electrical ground is required on this appliance You should make sure that the power cord is not pinched by the range or heavy objects Failure to do so can result in serious burns or electrical shock e You never remove the protectio
14. range has been designed to comply with the maximum allowable wood cabinet temperatures of 194 F e Cabinet storage space located above the surface units should be avoided e You should install a range hood that projects horizontally a minimum of 5 inches beyond the bottom of the cabinets If cabinet Storage is to be provided The risk of burns or fire by reaching over the heated surface elements can be reduced e You should not install the range in the humid place Splashing the range with water or any electrolyte can result in electrical shock e You should not let cooking grease or flammable material accumulate in or near the range Failure to do so can result in serious burns SAFETY 5 A WARNING e The information in this manual should be followed exactly A fire or electrical shock may result causing property damage personal injury or death A WARNING e Any person should not step or ye sit on the oven door You should ax he supplied with the range The range could be tipped and injury might result from spilled hot k liquid food or the range itself If the range is pulled away from the other reason ensure that the Anti Tip Device is properly reengaged when the range is pushed back against the wall Broiling beyond install the Anti Tip Brackets wall for cleaning service or any recommended cooking times A CAUTION e You should put on gloves during the installation procedu
15. re Failure to do so can result in bodily injury NOTE e Read all instructions contained in these installation instructions before installing range e Remove all packing materials from the oven compartments before connecting the electrical supply to the range e Observe all governing codes and ordinances e Be sure to leave these instructions with the consumer O NOTE Keep these instructions with your owner s manual for future reference e As when using any appliance generating heat there are certain safety precautions you should follow e Be sure your range is installed and grounded properly by a qualified installer or service technician e Make sure the wall coverings around the range can withstand the heat generated by the range e To eliminate the need to reach over the surface elements cabinet storage space above the elements should be avoided PREPARE TO INSTALL THE RANGE TOOLS NEEDED Da Phillips Screwdriver Un Flat blade Screwdriver CA 1 4 Nut Driver e Pliers 3 y Tape Measure Safety Glasses CCS Pencil PARTS PROVIDED Anti Tip Brackets 2 TOY Lag Bolts 12 Template 1 AAAA AAA ARE AALS EIA ie OC Sel Anchor Sleeves 12 For Anti Tip Bracket Mounted on Concrete Floors and Walls N UL Approved 40 or 50 AMP Strain Relief For Conduit 4 Wire Cord OR 3 Wire Cord Installations Only m Z T L
16. y reengaged when the range is pushed back against the wall Broiling beyond recommended cooking times Anti tip bracket a Screw must enter wood 77 7777 or concrete j ff gt _ gt Z Wall plate NNNNANNNA NNN ANNAANNNNNNANY 1 Locate the brackets using the template Anti tip brackets are packaged with the template The instructions include necessary information to complete the installation Read and follow range installation instruction sheet template 2 Level the range Level the range by adjusting the leveling legs with a wrench Lower n range s Leg ae leveler Use a level to check your adjustments Place the level diagonally on the oven rack and check each direction for level First check direction ievel After check direction C If the level doesn t show level on the rack adjust the leveling legs with a wrench FINAL INSTALLATION Move range close enough to the opening to plug into the receptacle e Slide range into position insuring that both back legs slide under the anti tip brackets Range should sit flush against the back wall when properly installed Carefully attempt to tip range forward to insure that the anti tip brackets are engaged properly If properly installed the anti brackets will prevent the range from being tipped If the range can be tipped reinstall the range until the brackets ar
Download Pdf Manuals
Related Search