LG L1972H User's Manual
Contents
1. Adjust the brightness and the contrast e If the display is in power saving mode try moving the mouse or pressing any key on the keyboard to bring up the screen e Try to turn on the PC This message appears when the signal from the PC video card is out of horizontal or vertical frequency range of the display See the Specifications section of this manual and configure your display again This message appears when the signal cable between your PC and your display is not connected Check the signal cable and try again Do you see OSD LOCKED when you push MENU button Do you see a OSD LOCKED message on the screen e You can secure the current control settings so that they cannot be inadvertently changed You can unlock the OSD controls at any time by pushing the MENU button for several seconds the message OSD UNLOCKED will appear D Troubleshooting Display Position is incorrect On the screen background vertical bars or stripes are visible Any horizontal noise appearing in any image or characters are not clearly portrayed Important Display image is incorrect Press the AUTO SET button to automatically adjust your display image to the ideal setting If the results are unsatisfactory adjust the image position using the H position and V position icon in the on screen display2. Self Image Setting Function is executed automatically eae ere Only Analog M ode PROCESSING SELF NOTE Self Image Setting Function This function provides the user with optimal display settings When the user connects the monitor for the first time this function automatically adjusts the display to optimal settings for individual input signals AUTO SET Function When you encounter problems such as blurry screen blurred letters screen flicker or tilted screen while using the device or after changing screen resolution press the AUTO SET function button to improve resolution Connecting the Display To arrange the cables 1 Insert and screw the cable holder into the hole in the back of the stand until it will not turn any more as shown in the following figure OE 2 After connecting the cables neatly arrange the cables to the Cable Holder as shown in the following figure Cable Holder Control Panel Functions Front Panel Controls ZOOMING MENU ENGINE SOURCE AUTO SET Bottom BCOMWMs MN ALYMHME SA Control Function ZOOMING At the current display Use ez Zooming Key then the display resolution is transferred to the one step low resolution Use ez Zooming Key one more the display is back to the original display Those with poor eyesight such as the elderly those who have difficulty using computers and children can enlarge text or pictures by adjusting res
3. e Press the AUTO SET button to automatically adjust your display image to the ideal setting If the results are unsatisfactory decrease the vertical bars or stripes using the CLOCK icon in the on screen display e Press the AUTO SET button to automatically adjust your display image to the ideal setting If the results are unsatisfactory decrease the horizontal bars using the PHASE icon in the on screen display Check Control Panel gt Display gt Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting Set the color setting higher than 24 bits true color a Check Control Panel gt Display gt Settings and see if the frequency or the resolution were changed If yes readjust the video card to the recommend resolution a The setting method can differ by computer and O S Operation System and resolution mentioned above may not be supported by the video card performance In this case please ask to the computer or the video card manufacturer Troubleshooting Display image is incorrect The screen color is e Check if the signal cable is properly connected mono or abnormal and use a screwdriver to fasten if necessary Make sure the video card is properly inserted in the slot Set the color setting higher than 24 bits true color at Control Panel Settings The screen blinks e Check if the screen is set to interlace mode and if yes
4. change it to the recommend resolution Have you installed the display driver Have you installed the Be sure to install the display driver from the display display driver driver CD or diskette that comes with your display Or you can also download the driver from our web site http www l ge com Do you see an Make sure to check if the video card supports Unrecognized monitor Plug amp Play function Plug amp Play VESA DDC monitor found message Specifications Display Sync Input Video Input Resolution Plug amp Play Power Consumption Dimensions amp Weight Tilt Height Range Power Input Environmental Conditions Stand Base Power cord NOTE 19 inches 48 26 cm Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 48 26 cm 0 294 mm pixel pitch Horizontal Freq Analog 30 83 kHz Automatic Digital 30 71 kHz Automatic Vertical Freq 56 75 Hz Automatic Input Form Separate TTL Positive Negative SOG Sync On Green Digital HDCP Signal Input 15 pin D Sub Connector DVI D connector Digital Input Form RGB Analog 0 7 Vp p 75 ohm Digital Max Analog VESA 1280 x 1024 75 Hz Digital VESA 1280 x 1024 60 Hz Recommend VESA 1280 x 1024 60 Hz DDC 2B On Mode 34 W Typ Sleep Mode lt 1W Off Mode lt 1W 1 Height 2 Height Width Depth Width Dept
5. your service technician for replacement Do not Open the Display a There are no user serviceable components inside a There are Dangerous High Voltages inside even when the power is OFF a Contact your dealer if the display is not operating properly To Avoid Personal Injury a Do not place the display on a sloping shelf unless properly secured a Use only a stand recommended by the manufacturer Do not drop an object on or apply impact to the product Do not throw any toys or objects on the product screen It can cause injury to human problem to product and damage the display To Prevent Fire or Hazards a Always tum the display OFF if you leave the room for more than a short period of time Never leave the display ON when leaving the house a Keep children from dropping or pushing objects into the display s cabinet openings Some intemal parts carry hazardous voltages a Do not add accessories that have not been designed for this display a When the display is to be left unattended for an extended period of time unplug it from the wall outlet a Inthe presence of thunder and lightning never touch the power cord and signal cable because it can be very dangerous It can cause electric shock Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord and do not place the display where the power cord is subject to damage Do not use this display near water such as near a batht
6. IE MOVIE For animation images in videos or movies MENUS e C SET a MENU Exit TEXT For text images Word processing etc a Move SET Select FLATRON ENGINE User Be mH wz You can manually adjust brightness ACE or RCM You can save or restore the adjusted value even USER d when using a different environment MENUS E SETHI TO UE eels Brightness Adjusts screen brightness ACE Adaptive Clarity Enhancer Selects the clarity mode RCM Real Color Management Selects the color mode Press the SET Button SSS Not applied SE Green enhance Es Flesh tone c SEHE Color Enhance ACE k Om __ 1 RCM iO JO SAVE MENUS SETE a MENU Exit a Decrease a Increase a SET Select another sub menu Select the sub menu using the SET button and save the YES value using the buttons FLATRON JENGINE H es m NORMAL This is under normal operating conditions JSER ey NORMAL MENUS SETIs Troubleshooting Check the following before calling for service No image appears Is the power cord of the display connected Is the power on and the power indicator blue or green Is the power indicator amber Do you see an OUT OF RANGE message on the screen Do you see a CHECK SIGNAL CABLE message on the screen Check and see if the power cord is connected properly to the power outlet
7. L To move image left and right VERTICAL To move image up and down fa VERTICAL QI a a MENU Exit Decrease a Increase a SET Select another sub menu On Screen Display OSD Selection and Adjustment Main menu Sub menu TRACKING TRACKING CLOCK PHASE 50 SHARPNESS PHASE AO 5 MENUS gt SETE MENU Exit Decrease Description To minimize any vertical bars or stripes visible on the screen background The horizontal screen size will also change To adjust the focus of the display This item allows you to remove any horizontal noise and clear or sharpen the image of characters Increase SHARPNESS To adjust the clearness of the screen a SET Select another sub menu Ej SETUP LANGUAGE OSD POSITION HORIZONTAL 0 16 50 er WHITE BALANCE MENUS O SET SETUP WHITE BALANCE gt NO POWER INDICATOR ON POWER MENUS gt SET amp INDICATOR MENU Exit Adjust Adjust a SET Select another sub menu FACTORY RESET To choose the language in which the control names are displayed To adjust position of the OSD window on the screen If the output of the video card is different the required specifications the color level may deteriorate due to video signal distortion Using this function the signal level is adjusted to fit into the standard output level of the video card in order t
8. T button prior to entering the On Screen Display OSD This will automatically adjust your display image to the ideal settings for the current screen resolution size display mode PROCESSING AUTO The best display mode is IMAGE ADJUSTMENT 1280 x 1024 5 Power Button Use this button to turn the display on or off This Indicator lights up as blue when the display is operating normally On Mode If the display is in Sleep Mode Energy Saving this indicator color will changes to amber O Power Indicator On Screen Display OSD Control Adjustment Screen Adjustment Making adjustments to the display s image size position and operating parameters is quick and easy with the On Screen Display Control system OSD A short example is given below to familiarize you with the use of the controls The following section is an outline of the available adjustments and selections you can make by using the OSD NOTE a Allow the display to stabilize for at least 30 minutes before making any image adjustments To make adjustments in the On Screen Display follow these steps MENU AUTO SET MENU Press the MENU button then the main menu of the OSD appears To select each item in the OSD menu use the or button When the icon you want is highlighted press the AUTO SET Button Use the buttons to adjust the image to the desired level Use the AUTO SET button to selec
9. User s Guide E L1972H Make sure to read the Important Precautions before using this product Keep the User s Guide CD in an accessible place for future reference Sec the attached label on the unit and show this information to your dealer when asking for service Important Precautions This unit has been engineered and manufactured to ensure your personal safety however improper use may result in potential electrical shock or fire hazards In order to allow the proper operation of all safeguards incorporated in this display observe the following basic rules for its installation use and servicing On Safety Use only the power cord supplied with the unit In case you use another power cord make sure that it is certified by the applicable national standards if not being provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authorized repair service provider for a replacement The power supply cord is used as the main disconnection device Ensure that the socket outlet is easily accessible after installation Operate the display only from a power source indicated in the specifications of this manual or listed on the display If you are not sure what type of power supply you have in your home consult with your dealer Overloaded AC outlets and extension cords are dangerous So are frayed power cords and broken plugs They may result in a shock or fire hazard Call
10. ding or folding the stand base Connecting the Display Folding the stand base 1 Face the front of the monitor dislpay Than gently push the monitor backwards following the sequence shown in the picture below Tilt range 1 Make sure that the angle of the panel is set for your comfort a Tilt Range 0 30 Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position the forward tilt angle of the monitor should not exceed 5 degrees Connecting the Display To adjust the height Scope of adjusting the height maximum 4 02 inches 102 mm Connecting the Display Using the Computer 1 Make sure to tum off the computer and product Connect the cable as below sketch map fom t Connect DVI Cable NOTE Connect Dsub Cable PC a This is a simplified representation of the rear view Connect Dsub Cable Mac a This rear view represents a general model your display may differ from the view as shown Power Cord 2 EA om mum 1 Signal Cable Varies according to model SJA DVI D This feature is not available in all countries o gt oq ore p MAC Mac adapter For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector 2 Press button on the side switch panel to tum the power on When monitor power is tumed on the
11. h Width x Height x Depth 1 40 88 cm 16 09 inches x 45 97 cm 18 10 inches x 23 60 cm 9 29 inches 2 40 88 cm 16 09 inches x 35 57 cm 13 93 inches x 9 70 cm 3 19 inches Net 5 2 kg 11 46 Ibs Tilt range 0 30 Height range 102 mm 4 02 inches AC 100 240V 50 60Hz 0 8A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached O Detached Wall outlet type or PC outlet type a Information in this document is subject to change without notice Preset Modes Resolution Display Modes Resolution Horizontal Freq kHz Vertical Freq Hz 1 VGA 640 x 350 31 469 70 2 VGA 720 x 400 31 468 70 3 VGA 640 x 480 31 469 60 4 VESA 640x480 37 500 75 5 VESA 800x600 37 879 60 6 VESA 800x600 46 875 75 7 MAC 832 x 624 49 725 75 8 VESA 1024x768 48 363 60 9 VESA 1024x 768 60 123 75 10 MAC 1152 x 870 68 681 75 11 VESA 1152x900 61 805 65 12 VESA 1280 x 1024 63 981 60 13 VESA 1280 x 1024 79 976 75 Recommend Mode Only Analog Mode Indicator MODE LED Color On Mode blue Sleep Mode amber Off Mode Off Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device 1 Place the monitor with its front facing downward on a soft cloth or a cushion Gently hold Cover Hinge Cap with hands as shown in the picture Then lift i
12. icons icon names and icon descriptions of the all items shown on the Menu Press the MENU Button then the main menu of the OSD appears Menu Name PICTURE CONTRAST Icons gt Om 1m 50 GAMMA 7 Om 0 Sub menus MENUS iel 5 SET Button Tip a MENU 6 Exit e Adjust Decrease Increase SET e Enter 4 Select another sub menu NOTE OSD On Screen Display menu languages on the monitor may differ from the manual On Screen Display OSD Selection and Adjustment Main menu Description DI PICTURE PICTURE BRIGHTNESS To adjust the brightness of the screen i CONTRAST To adjust the contrast of the screen CONTRAST ante GAMMA Set your own gamma value 50 0 50 NS eect On the monitor high gamma values display whitish images and low gamma MENUS O SETE values display high contrast images MENU Exit Decrease Increase a SET Select another sub menu RGB eS COLOR COLOR PRESET e SRGB Set the screen color to fit the C PRESET SRGB standard color has ok 200k specification i o e 6500K Slightly reddish white GREEN E o 9300K Slightly bluish white BLUE Se RED Set your own red color levels MENUS gt SET GREEN Set your own green color levels MENU Exit Decrease BLUE Set your own blue color levels a Increase a SET Select another sub menu POSITION POSITION HORIZONTA
13. n a Use a slightly damp not wet cloth Do not use an aerosol directly on the display screen because over spraying may cause electrical shock On Repacking Do not throw away the carton and packing materials They make an ideal container in which to transport the unit When shipping the unit to another location repack it in its original material On Disposal a The fluorescent lamp used in this product contains a small amount of mercury a Do not dispose of this product with general household waste Disposal of this product must be carried out in accordance to the regulations of your local authority Connecting the Display a Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Unfolding the stand base 1 Place the monitor with its front facing downward on a soft cloth 2 Hold the stand base and lift it up following the sequence as shown in the picture ry 3 Pull the stand base down at the same spot shown in the picture and the stand will be unfolded a 4 Place the monitor upright and adjust the stand y base to the desired angle Adjust the stand base s angle by holding the edges of the monitor gently with both hands Important a This illustration depicts the typical connection procedure Your monitor may differ from the one displayed in the pictures above a Do not touch or apply force to the monitor s screen while expan
14. o provide the optimal image Activate this function when white and black colors are present in the screen Use this function to set the power indicator on the front side of the monitor to ON or OFF If you set OFF it will go off If you set ON at any time the power indicator will automatically be turned on Restore all factory default settings except LANGUAGE Press the button to reset immediately If this does not improve the screen image restore the factory default settings If necessary perform the white balance function again This function will be enabled only when the input signal is an analog signal On Screen Display OSD Selection and Adjustment ug The OSD screen will appear when you touch the ENGINE button on the front of the monitor FLATRON ENGINE Bs USER NORMAL Sub menu Name MENUS P SET e FLATRON F EN GINE Screen when applied Screen when not applied When you execute F ENGINE two tones will appear on the screen as shown The applied screen will e NES appear on the left side whereas the non applied screen will appear on the right side Press the SET button to use the adjusted screen MOVIE MENUD E O SET Is Main menu Sub menu Description FLATRON JENGINE MOVIE This feature lets you easily select the best desired en Us A TEXT image condition optimized to the environment ambient illumination image types etc MOV
15. olution with a single touch a To use this feature please install forteManager program in the enclosed CD ROM a The resolutions at which the EZ ZOOMING operates are as follows 1280 x 1024 1024 x 768 800 x 600 The setting method can differ by O S or video card In this case Please ask to the computer or the video card manufacturer 2 MENU Button Use this button to enter or exit from the On Screen Display OSD LOCKED UNLOCKED This function allows you to lock the current control settings so oD LockeD that these settings are not inadvertently changed To lock the E OSD settings press and hold the MENU button for several seconds The message OSD LOCKED appears You can unlock the OSD settings at any time by pushing the MENU button for several seconds The message OSD UNLOCKED appears Control Panel Functions Control Function B Use these buttons to select or adjust functions in the Butons On Screen Display Button For more information refer to page A15 JENGINE pag NORMAL MENU B Button Use this button to make either D Sub or DVI SOURCE Hot key connector active This feature is used when two computers are connected to the display The default setting is D Sub AUTO SET Use this button to selection an icon in the On Screen Button Display AUTO IMAGE ADJUSTMENT When adjusting your display settings always press the AUTO SE
16. t other sub menu items Press the MENU button once to retum to the main menu to select another function Press the MENU button twice to exit from the OSD On Screen Display OSD Selection and Adjustment The following table indicates all the On Screen Display control adjustment and setting menus Main menu Sub menu AJD Reference PICTURE BRIGHTNESS To adjust the brightness CONTRAST ele contrast and gamma of the screen GAMMA e e COLOR PRESET SRGB To customize the color of 6500K the screen 9300K o RED GREEN BLUE HORIZONTAL To adjust the position of the POSITION VERTICAL r screen CLOCK To improve the clarity and TRACKING PHASE stability sharpness of the screen SHARPNESS LANGUAGE To customize the screen SETUP OSD HORIZONTAL status for a user s operating environment POSITION VERTICAL WHITE BALANCE J POWER INDICATOR FACTORY RESET ELATRON MOVIE TEXT e e To select or customize F ENGINE USER desired image settings NORMAL e Adjustable A Analog Input D Digital Input NOTE a The order of icons may differ depending on the model A11 A15 On Screen Display OSD Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system Listed below are the
17. t up and separate from the body gt Cover Hinge Cap 2 Separate the stand base by using a screwdriver Pq 3 Install the Wall mount plate Wall mount plate Separate purchase This is stand type or wall mount type and is connectable with Wall mount plate Please refer to the installation guide for more details which is provided when Wall mount plate is purchased Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores Digitally yours sana Le
18. ub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation If these openings are blocked built up heat can cause failures which may result in a fire hazard Therefore NEVER a Block the bottom ventilation slots by placing the display on a bed sofa rug etc a Place the display in a builtin enclosure unless proper ventilation is provided a Cover the openings with cloth or other material a Place the display near or over a radiator or heat source a Main power breaker is the power cord and this breaking device must be located at a location where it is easy to operate Do not rub or strike the Active M atrix LCD with anything hard as this may scratch mar or damage the Active Matrix LCD permanently Do not press the LCD screen with your finger for a long time as this may cause some afterimages Some dot defects may appear as Red Green or Blue spots on the screen However this will have no impact or effect on the display performance If possible use the recommended resolution to obtain the best image quality for your LCD display If used under any mode except the recommended resolution some scaled or processed images may appear on the screen However this is characteristic of the fixed resolution LCD panel On Cleaning Unplug the display before cleaning the face of the display scree
Download Pdf Manuals
Related Search