LG E2341V User's Manual
Contents
1. Recommend Mode m HDMI Timing Display Modes Resolution Horizontal Freq kHz Vertical Freq Hz 1 480P 31 50 60 2 576P 31 25 50 3 720P 37 50 50 4 720P 45 00 60 5 1080i 28 12 50 6 1080i 33 75 60 7 1080P 56 25 50 8 1080P 67 50 60 Indicator On Mode Blue Sleep Mode Blue blinking Off Mode Off Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device 1 Place the monitor with its front facing downward on a soft cloth l 2 Remove the Stand Body and Stand Base from product in correct direction as shown in the picture Installing the Wall mount plate 3 Install the Wall mount plate Wall mount plate Separate purchase This is stand type or wall mount type and is connectable with Wall mount plate Please refer to the installation guide for more details which is provided when Wall mount plate is purchased Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores lt Screw Mounting Interface Dimension gt Hole spacing 75 mm x 75 mm NOTE a VESA compatible only with respect to screw mounting interface dimensions and mounting screw specifications a Please use VESA standard as below 784 8 mm and under 30 9 inch Wall Mount Pad Thickness 2 6 mm Screw 6 4 0 mm x Pitch 0 7 mm x Length 10 mm 787 4 mm and above 31 02. LG Life s Good OWNER S MANUAL LCD MONITOR Please read this manual carefully before operating your set and retain it for future reference LCD MONITOR MODEL E22 41V E2341V E2341VG E2441V www lg com Important Precautions This unit has been engineered and manufactured to ensure your personal safety however improper use may result in potential electrical shock or fire hazards In order to allow the proper operation of all safeguards incorporated in this display observe the following basic rules for its installation use and servicing On Safety Use only the power cord supplied with the unit In case you use another power cord make sure that it is certified by the applicable national standards if not being provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authorized repair service provider for a replacement The power supply cord is used as the main disconnection device Ensure that the socket outlet is easily accessible after installation Operate the display only from a power source indicated in the specifications of this manual or listed on the display If you are not sure what type of power supply you have in your home consult with your dealer Overloaded AC outlets and extension cords are dangerous So are frayed power cords and broken plugs They may result in a shock or fire hazard Call your service technician for replacement As
3. Do you see a CHECK This message appears when the signal cable SIGNAL CABLE between your PC and your display is not message on the connected Check the signal cable and try again screen Do you see a OSD LOCKED message on the screen Do you see OSD e You can secure the current control settings LOCKED when you so that they cannot be inadvertently changed push MENU button You can unlock the OSD controls at any time by pushing the MENU button for several seconds the message OSD UNLOCKED will appear Troubleshooting Display image is incorrect Display Position is incorrect On the screen background vertical bars or stripes are visible Any horizontal noise appearing in any image or characters are not clearly portrayed e Press the AUTO button to automatically adjust your display image to the ideal setting e Press the AUTO button to automatically adjust your display image to the ideal setting e Press the AUTO button to automatically adjust your display image to the ideal setting e Check Control Panel gt Display gt Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting Set the color setting higher than 24 bits true color IMPORTANT a Check Control Panel gt Display gt Settings and see if the frequency or the resolution were changed If yes readjust the video card to the r
4. NO SUPER ENERGY SAVING gt RESET YES TOTAL POWER REDUCTION How much power is saved during using the monitor TOTAL CO2 REDUCTION Change the TOTAL POWER REDUCTION to CO2 On Screen Display OSD Selection and Adjustment NOTE SAVING DATA W h p22 inch 23 inch 24 inch Saving Data depends on the Panel So those values should be different from each panel and panel vendor LG accumulate those values using integrated function with 10 minutes broadcast v ideo signal LED Saving means that how much power can be saved using WLED Panel instead of CCFL panel SUPER Saving means that how much power can be more saved using SUPER E NERGY SAVING function Troubleshooting Check the following before calling for service No image appears Is the power cord of the e Check and see if the power cord is connected display connected properly to the power outlet Is the power indicator Press the Power button light on Is the power indicator e If the display is in power saving mode try moving flickering the mouse or pressing any key on the keyboard to bring up the screen e Try to turn on the PC Do you see an OUT OF This message appears when the signal from the RANGE message on PC video card is out of horizontal or vertical the screen frequency range of the display See the Specifications section of this manual and configure your display again
5. inch Please use VESA standard wall mount pad and screws Life s Good Make sure to read the Safety Precautions before using the product Keep the OWNER S MANUAL CD in an accessible place for furture reference The model and serial number of the SET is ENERGY STAR is a set of power saving located on the back or one side of the SET guidelines issued by the U S Environmental Record it below should you ever need service Protection Agency EPA As an ENERGY STAR Partner LGE U S A lnc has determined that this product meets the ENERGY STAR guidelines for energy efficiency MODEL SERIAL
6. d phone cable installed properly e Check sound format Not supply to compressed sound format Specifications E2241V 54 6 cm 21 5 inch Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 54 6 cm 0 248 mm x 0 248 mm Pixel pitch Horizontal Freq 30 kHz to 83 kHz Automatic Vertical Freq Analog Digital 56 Hz to 75 Hz Automatic HDMI 56 Hz to 61 Hz Automatic Input Form Separate Sync Digital Signal Input 15 pin D Sub Connector DVI D connector Digital HDMI TYPE A Connector Input Form Analog 0 7 Vp p 75 ohm Digital HDMI VESA 1920 x 1080 60 Hz Recommend VESA 1920 x 1080 60 Hz 3 0 x lt DDC 2B Digital HDMI DDC2B On Mode 24 W Typ Sleep Mode lt 0 3 W Off Mode lt 0 3 W With Stand Without Stand Heigh 38 80 cm 15 27 inch Height 32 20 cm 12 67 inch Depth 16 60 cm 6 54 inch Depth 5 80 cm 2 28 inch Weight excl packing 2 9 kg 6 39 Ib I I I Width 50 90 cm 19 80 inch Width 50 90 cm 19 80 inch I I Tilt 5 to 15 AC 100 240 V 50 60 Hz 1 0 A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type NOTE a Information in this document is subject to change without notice Specifications Horizontal Freq Vertical F
7. e AUTO button on the MONITOR SETUP OSD Only Analog Mode This will automatically adjust your display image to the ideal settings for the current screen resolution size display mode The best display mode is E2241V E2341V E2341VG E2441V 1920 x 1080 When two input signals at least are connected you can select the input signal D SUB DVI HDMI you want When only one signal is connected it is automatically detected The default setting is D Sub Exit the OSD On Screen Display Use this button to turn the display on or off The power indicator stays blue if the display is running properly On Mode If the display is in Sleep Mode the power indicator is blinking blue On Screen Display OSD Control Adjustment Screen Adjustment Making adjustments to the image size position and operating parameters of the display is quick and easy with the On Screen Display Control system A short example is given below to familiarize you with the use of the controls The following section is an outline of the available adjustments and selections you can make using the OSD To make adjustments in the On Screen Display follow these steps BRIGHTNESS ORIGINAL RATIO e COLOR TEMP PRESET Press the discretionary Button then the main menu of the OSD appears To access a control use the corresponding Buttons Use the lt gt V Buttons to adjust the image to the desired level U
8. e sure to use a screen saver on the product Burn in and related problems are not covered by the warranty on this product Do not shock or scratch the front and sides of the screen with metallic objects Otherwise it may cause damage to the screen Make sure the panel faces forward and hold it with both hands to move If you drop the product the damaged product can cause electric shock or fire Contact an authorized the service center for repair Avoid high temperatures and humidity Important Precautions On Cleaning a Unplug the display before cleaning the face of the display screen a Use a slightly damp not wet cloth Do not use an aerosol directly on the display screen because over spraying may cause electrical shock a When cleaning the product unplug the power cord and scrub gently with a soft cloth to prevent scratching Do not clean with a wet cloth or spray water or other liquids directly onto the product An electric shock may occur Do not use chemicals such as benzene paint thinners or alcohol Spray water onto a soft cloth 2 to 4 times and use it to clean the front frame wipe in one direction only Too much moisture may cause staining On Repacking a Do not throw away the carton and packing materials They make an ideal container in which to transport the unit When shipping the unit to another location repack it in its original material On Disposal D
9. ecommend resolution a If the recommended resolution optimal resolution is not selected letters may be blurred and the screen may be dimmed truncated or biased Make sure to select the recommend resolution The setting method can differ by computer and O S Operation System and resolution mentioned above may not be supported by the video card performance In this case please ask to the computer or the video card manufacturer Troubleshooting Display image is incorrect The screen color is e Check if the signal cable is properly connected mono or abnormal and use a screwdriver to fasten if necessary e Make sure the video card is properly inserted in the slot e Set the color setting higher than 24 bits true color at Control Panel Settings The screen blinks e Check if the screen is set to interlace mode and if yes change it to the recommend resolution Do you see an Unrecognized monitor Plug amp Play VESA DDC monitor found message Have you installed the e Be sure to install the display driver from the display display driver driver CD or diskette that comes with your display Or you can also download the driver from our web site http www lg com e Make sure to check if the video card supports Plug amp Play function The Audio function is not working Picture OK amp No sound Check whether volume is 0 e Check sound muted e HDMI cable installed properly e Hea
10. electing and adjusting an item using the OSD system Listed below are the icons icon names and icon descriptions of the all items shown on the Menu Press the SUPER ENERGY SAVING Button then the main menu of the OSD appears Menu Name Sub menus SUPER ENERGY SAVING ON OFF RESET TOTAL POWER REDUCTION 20W cons TOTAL CO2 REDUCTION 16g EXIT Exit Button lt P Adjust Decrease Increase Tip Restart to select sub menu NOTE s OSD On Screen Display menu languages on the monitor may differ from the manual On Screen Display OSD Selection and Adjustment Main menu Sub menu SUPER ENERGY SAVING oe ON OFF TOTAL POWER REDUCTION 20W ON RESET TOTAL CO2 REDUCTION 16g OFF ON OFF RESET TOTAL POWER REDUCTION 20W TOTAL CO2 REDUCTION 16g SUPER ENERGY SAVING RESET RESET ON OFF TOTAL POWER REDUCTION 20W TOTAL CO2 REDUCTION 16g Exit Exit a lt 4 P Move Select another sub menu OK Select Description Turn on the SUPER ENERGY SAV ING function When current setting value is ON the SUPER SAVING color is green Turn off the SUPER ENERGY SAV ING function Now the monitor is LED SAVING function When current setting value is OFF the SUPER SAVING color is gray Clear the TOTAL POWER REDUC TION and TOTAL CO2 REDUCTION values SUPER ENERGY SAVING RESET LETEI
11. ertical Freq Analog Digital 56 Hz to 75 Hz Automatic HDMI 56 Hz to 61 Hz Automatic Input Form Separate Sync Digital Signal Input 15 pin D Sub Connector DVI D connector Digital HDMI TYPE A Connector Input Form Analog 0 7 Vp p 75 ohm Digital HDMI VESA 1920 x 1080 60 Hz Recommend VESA 1920 x 1080 60 Hz z pe gt x lt DDC 2B Digital HDMI DDC 2B On Mode 25 W Typ Sleep Mode lt 0 3 W Off Mode lt 0 3 W With Stand Without Stand Width 56 93 cm 22 41 inch Height 41 91 cm 16 50 inch Depth 17 93 cm 7 05 inch Weight excl packing 4 0 kg 8 81 Ib Width 56 93 cm 22 41 inch Height 35 43 cm 13 94 inch Dept 5 93 cm 2 33 inch Tilt 5 to 15 AC 100 240 V 50 60 Hz 1 2 A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type NOTE a Information in this document is subject to change without notice E2441V Preset Modes Resolution E DSUB DVI Timing Display Modes Resolution OONOTLRWN 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 1050 1920 x 1080 31 468 31 469 37 500 37 879 46 875 48 363 60 123 67 500 63 981 79 976 65 290 67 500 Horizontal Freq kHz Vertical Freq Hz Polarity H V
12. long as this unit is connected to the AC wall outlet it is not disconnected from the AC power source even if the unit is turned off Do not Open the Display There are no user serviceable components inside a There are Dangerous High Voltages inside even when the power is OFF a Contact your dealer if the display is not operating properly To Avoid Personal Injury a Do not place the display on a sloping shelf unless properly secured a Use only a stand recommended by the manufacturer a Do not drop an object on or apply impact to the product Do not throw any toys or objects on the product screen It can cause injury to human problem to product and damage the display To Prevent Fire or Hazards a Always turn the display OFF if you leave the room for more than a short period of time Never leave the display ON when leaving the house a Keep children from dropping or pushing objects into the display s cabinet openings Some internal parts carry hazardous voltages a Do not add accessories that have not been designed for this display a When the display is to be left unattended for an extended period of time unplug it from the wall outlet a In the presence of thunder and lightning never touch the power cord and signal cable because it can be very dangerous It can cause electric shock Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord and do not place the display where
13. ly if input resolution is lower than monitor ratio 16 9 PRESET Select the screen color an al e WARM Set the screen to warm color temperature a warm e MEDIUM Set the screen to medium color temperature e COOL Set the screen to cool color temperature USER le RED Set your own red color levels GREEN Set your own green color levels BLUE Set your own blue color levels Exit Exit lt P VY Move Select another sub menu On Screen Display OSD Selection and Adjustment Main menu Sub menu Description CONTRAST To adjust the contrast of the screen LANGUAGE FACTORY RESET BLACK LEVEL Only HDMI input You can set the offset level If you select HIGH the screen will be bright and if you select LOW the screen will be dark only for HDMI input Offset As the criteria for video signal it is the darkest screen the monitor can show LANGUAGE To choose the language in which the control names are displayed ca LANGUAGE 4 ENGLISH 1 17 _ gt FACTORY RESET 4 gt Restore all factory default settings except LANGUAGE Press the lt d gt buttons to reset immediately a Exit Exit lt gt V Move Select another sub menu On Screen Display OSD Selection and Adjustment mm YOU were introduced to the procedure of s
14. nnects the monitor for the first time this function automatically adjusts the display to optimal settings for individual input signals AUTO Function When you encounter problems such as blurry screen blurred letters screen flicker or tilted screen while using the device or after changing screen resolution press the AUTO function button to improve resolution Control Panel Functions Front Panel Controls For D SUB and DVI input MONITOR SETUP Fae amp lt SUPER MENU ENERGY AUTO SAVING MONITOR SETUP INPUT EXIT HA A ad I SUPER MENU ENERGY VOLUME INPUT EXIT SAVING 1 MENU Button OSD LOCKED OSD UNLOCKED OSD LOCKED UNLOCKED This function allows you to lock the current control settings so that they cannot be inadvertently changed Press and hold the MENU button for several seconds The message OSD LOCKED should appear You can unlock the OSD controls at any time by pushing the MENU button for several seconds The message OSD UNLOCKED should appear Control Panel Functions 2 SUPER ENERGY SAVING Button AUTO Button For D SUB and DVI input PROCESSING AUTO IMAGE ADJUSTMENT VOLUME Button Only for HDMI input O INPUT Button SOURCE Hot key 5 EXIT Button Power Button amp Power Indicator Use this button to enter SUPER ENERGY SAVING menus For more information refer to page 15 AUTO IMAGE ADJUSTMENT When adjusting your display settings always press th
15. o not dispose of this product with general household waste Disposal of this product must be carried out in accordance to the regulations of your local authority Accessories Thank for selecting LGE products Please make sure the following items are included with your monitor If any items are missing contact your dealer DVI D Signal Cable 15 pin D Sub Signal Cable This feature is not available in all To set it up this signal cable may be countries attached to this product before shipping out NOTE a This accessories may look different from those shown here a User must use shielded signal interface cables D sub 15 pin cable DVI D cable with ferrite cores to maintain standard compliance for the product Connecting the Display a Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Connecting the stand 1 Place the monitor with its front facing downward on a soft cloth 2 Assemble the stand Body into the 3 Assemble the Stand Base Front product in the correct direction as shown in Rear into the Stand Body in the the picture Make sure you push it until you correct direction hear it click Stand Base 4 Use a coin on the back of the stand base and turn the screw clockwise to tighten 5 Once assembled take the monitor up carefully and face the front side Important This illustration depict
16. req Input Form Signal Input Input Form Recommend z ped gt x lt On Mode Sleep Mode Off Mode With Stand E2341V E2341VG 58 4 cm 23 inch Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 58 4 cm 0 265 mm x 0 265 mm Pixel pitch 30 kHz to 83 kHz Automatic Analog Digital 56 Hz to 75 Hz Automatic HDMI 56 Hz to 61 Hz Automatic Separate Sync Digital 15 pin D Sub Connector DVI D connector Digital HDMI TYPE A Connector Analog 0 7 Vp p 75 ohm Digital HDMI VESA 1920 x 1080 60 Hz VESA 1920 x 1080 60 Hz DDC 2B Digital HDMI DDC 2B 28 W Typ lt 0 3 W lt 0 3 W Without Stand Width 54 60 cm 21 49 inch Height 40 70 cm 16 02 inch Depth 20 20 cm 7 95 inch Width 54 60 cm 21 49 inch Height 34 20 cm 13 46 inch Depth 5 7 cm 2 24 inch Weight excl packing Tilt 5 to 15 AC 100 240 V 50 60 Hz 1 0 A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type NOTE a Information in this document is subject to change without notice Specifications 60 97 cm 24 inch Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 60 97cm 0 277 mm x 0 277 mm Pixel pitch Horizontal Freq 30 kHz to 83 kHz Automatic V
17. s the general model of connection Your monitor may differ from the items shown in the picture Do not carry the product upside down holding only the stand base The product may fall and get damaged or injure your foot Connecting the Display Disassembling the stand 1 Puta cushion or soft cloth on aflat 2 Place the monitor face Down on the surface cushion or soft cloth 3 Remove the Stand Body and Stand 4 Use a coin on the back of the Stand Base from product in correct Base and turn the screw anticlock direction as shown in the picture wise to loosen Connecting the Display Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Positioning your display After installation adjust the angle as shown below 1 Adjust the position of the panel in various ways for maximum comfort Tilt Range 5 to 15 AN Do not touch or press the screen when adjusting the angle of the monitor a When adjusting the angle of the screen do not put your finger s in between the head of the monitor and the stand body You can hurt your finger s ERGONOMIC a It is recommended that in order to maintain an ergonomic and comfortable viewing position the forward tilt angle of the monitor should not exceed 5 degrees Connecting the Display E2241V E2341V E2341VG E2441V Connecting with the PC 1 Before setting up the monitor ensure that
18. se the Button to select other sub menu items 9 Press the EXIT Button to exit from the OSD On Screen Display OSD Selection and Adjustment The following table indicates all the On Screen Display control adjustment and setting menus Main menu Sub menu Supported input Description BRIGHTNESS COLOR TEMP PRESET USER NOTE The order of icons may differ depending on TE D SUB Analog signal input DVI D Digital signal input EN HDMI signal SIE To adjust the brightness of the screen To customize the color of the screen To adjust the contrast of the screen To adjust the black level of the screen To customize the screen status for a user s operating i environment TJ Tum on the SUPER ENERGY SAVING function Turn off the SUPER ENERGY SAVING function i Initialize the SUPER ENERGY 1 SAVING and set to OFF mode the model 12 17 On Screen Display OSD Selection and Adjustment Main menu Sub menu Description BRIGHTNESS To adjust the brightness of the screen BRIGHTNESS gt 100 m1 WIDE gt gt gt w ORIGINAL RATIO 4 e COLOR TEMP 4 PRESET 4 PRESET WARM WIDE Switch to full screen mode according to input image signal BRIGHTNE gt 100 ORIGINAL RATIO WIDE 1 2 gt g ae ORIGINAL Change the input image signal ratio to original This function works on
19. the power cord is subject to damage Do not use this display near water such as near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation If these openings are blocked built up heat can cause failures which may result in a fire hazard Therefore NEVER a Block the bottom ventilation slots by placing the display on a bed sofa rug etc Place the display in a built in enclosure unless proper ventilation is provided Cover the openings with cloth or other material a Place the display near or over a radiator or heat source Do not rub or strike the Active Matrix LCD with anything hard as this may scratch mar or damage the Active Matrix LCD permanently Do not press the LCD screen with your finger for a long time as this may cause some afterimages Some dot defects may appear as Red Green or Blue spots on the screen However this will have no impact or effect on the display performance If possible use the recommended resolution to obtain the best image quality for your LCD display If used under any mode except the recommended resolution some scaled or processed images may appear on the screen However this is characteristic of the fixed resolution LCD panel Leaving a fixed image on the screen for a long time may cause damage to the screen and cause image burn in Mak
20. the power to the monitor the computer system and other attached devices is turned off 2 Connect signal input cable and power cord 2 in order then tighten the screw of the signal cable Connect DVI D Digital signal Cable Connect HDMI Cable Connect D sub Analog signal Cable NOTE a This is a simplified representation of the rear view a This rear view represents a general model your display may differ from the view as shown ss When using a D Sub signal input cable connector for Macintosh gt MAC Mac adapter For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector Connect the signal input cable and tighten Varies according to model it up by turning in the direction of the arrow Sa Q D SUB DVI D HDMI as shown in the figure Wall outlet type TT O Set Top Box DVD Video w Video Game Console HDMI is optimized on the AV equipment Not supported PC T Pc SI gt Pc A Headphone Speaker 3 Press the power button on the front panel to turn the power on When monitor power is turned on the Self Image Setting Function is executed automatically Only Analog Mode Gy z 2 J PROCESSING SELF IMAGE SETTING Power Button NOTE Self Image Setting Function This function provides the user with optimal display settings When the user co
Download Pdf Manuals
Related Search