Leviton 5-Port Gigabit User's Manual
Contents
1. cord s other end to the intended port in a Category 5e or greater Voice amp Data Module which is already wired to the wall location 47611 5GB 3 Connect a patch cord from the NIC to the soon to be connected device at the wall location to complete the link Uplinking Cascading to Other Switches and Hubs Switches hubs and similar network devices are uplinked to the switch with straight through Category 5e cabling 1 Connect a Category 5e cable from the Uplink port on your network device to any port on the Switch Note 1000 Mbps is only supported in Category 5e or greater cables FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenn2. Z LEVITON Building A Connected World DI 041 47611 05A 10 100 1000 Mbps 5 Port Gigabit Ethernet Switch O O O O Ouwacr O 9099000m pn 72345 10 100 1000 Mbps 5 port Gigabit Ethern et Switch 5 Port Front Panel 5 4 3 2 1 ravoc eso 5 Port Rear Panel 59 25 Little Neck Parkway Little Neck N Y 11362 2591 USA Tech Support 800 824 3005 www leviton com Instructions for Use 10 100 1000 Mbps 5 Port Gigabit Ethernet Switch DESCRIPTION The 10 100 1000 Mbps 5 Port Gigabit Ethernet Switch is used to create a small Local Area Network LAN Patch cords connected from the Switch to structured wiring system connects network data devices throughout the home INSTALLATION To install the module into the Leviton Structured Media Center SMC simply align the mounting pins with the grid holes in the back of the SMC With the mounting pin plungers in the out position press the unit into the grid in the desired location Secure by pushing the plungers in Figure 1 Note To remove the bracket from the switch loosen the screws underneath the Switch and bracket combination then slide the units apart Front Panel Figure 2 A Power Illuminates green when powered up B LNK ACT LED LINK illuminates solid green when the port is connected to an ethernet or fast ethernet connection Activity illuminates blinking green when data is being transmitted or recei
3. a e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help IMPORTANT INSTRUCTIONS 1 Read and understand all instructions Follow all warnings and instructions marked on the product 2 Do not use this product near water e g near a tub wash basin kitchen sink or laundry tub in a wet basement or near a swimming pool 3 Never push objects of any kind into this product through openings as they may touch dangerous voltages 4 SAVE THESE INSTRUCTIONS SAFETY INFORMATION 1 Never install communications wiring or components during a lightning storm 2 Never install communications components in wet locations unless the components are designed specifically for use in wet locations 3 Never touch uninsulated wires or terminals unless the wiring has been disconnected at the network interface 4 Use caution when installing or modifying communications wiring or components 5 To prevent electrical shock each opening must be filled with a module g LEVITON Building A Connected World 59 25 Little Neck Parkway Little Neck N Y 11362 2591 USA Tech Support 800 824 3005 www Leviton com DI 041 47611 05A LEVITON ARTWORK SPECIFICATIONS e Artwork No Rev Level pj 041 47611 05A e Color s 1 over 1 1 Black 2 3 4 5 6 e Font Fami
4. lies Helvetica e Material Type 50 Ib offset Gauge e Coating L Aqueous Gloss Blister Coating Wax Free Inks DOCUMENTATION e ECO No N A e Art Revision Description e Artist HSZ Date _03 05 07 The information in this document is the exclusive PROPRIETARY property of LEVITON MANUFACTURING COMPANY INC It is disclosed with the understanding that acceptance or review by the recipient constitutes an undertaking by the recipient 1 to hold this information in strict confidence and 2 not to disclose duplicate copy modify or use the information for any purpose other than that for which disclosed Copyright 1997 Leviton Mfg Co Inc Unpublished All Rights Reserved FOLD SCHEME 8 5 4 25 FINAL Fold Line
5. ved C 10 100 1000 LED Illuminates green when a 10 Mbps 100 Mbps or 1000 Mbps connection is made Rear Panel Figure 2 A RJ 45 Ports Switch is equipped with 5 RJ 45 ports designed to make 10 100 1000 Ethernet connections B Auto detect Uplink Use any port to cascade additional switches hubs or routers C Power Supply Port Connect the provided 12 VDC Power Supply to the Switch MAKING NETWORK CONNECTIONS 10 100 1000 Mbps is a specification for Ethernet networks based on twisted pair cabling The maximum length of a segment for 10 100 1000 Mbps networks is 100 meters The cable and connectors are commonly referred to as a Category 5e or greater patch cord and RJ 45 connectors respectively To establish 10 100 1000 Mbps connections you will need the following equipment e Twisted pair Category 5e or greater patch cord for switch to NIC network interface card connections e Twisted pair Category 5e or greater patch cord for switch to switch connections usually referred to as switch cascading Note An 10 100 1000 Mbps network card is also required for Gigabit operation Note In order to achieve 1000 Mbps Speed the connected devices must support 1000 Mbps networking speeds Establishing Connections 1 Ensure that both the Switch and the soon to be connected device are in the POWER OFF mode 2 Plug one end of a patch cord into an available 10 100 1000 Mbps Switch port Connect that
Download Pdf Manuals
Related Search