Home

Lenovo 6437 User's Manual

Contents

1. V ServeRAID controllerJ8 J9 E Hard disc drive backplane Bn J8 If you have other devices to install do so now Otherwise go to Completing the installation on page 24 Installing an IBM Remote Supervisor Adapter II SlimLine Install an optional Remote Supervisor Adapter II SlimLine in the Remote Supervisor Adapter Il SlimLine connector on the system board See the illustration in FSystem board optiona device connectors on page dor the locaton of the connector After the Remote Supervisor Adapter II SlimLine is installed the systems management port on the rear of the server is active Important When the optional Remote Supervisor Adapter II SlimLine is installed in the server you can install only a half length adapter in expansion slot 1 Notes 1 When you start the server for the first time after you install a Remote Supervisor Adapter II SlimLine the startup process will take several minutes longer than a typical startup Earlier versions of the Remote Supervisor Adapter II SlimLine might not work in this server See enove conlaccessores on information about the supported Remote Supervisor Adapter II SlimLine versions To install a Remote Supervisor Adapter II SlimLine complete the following steps
2. ae 20 Emn es 88888885859 Hd 205228 L HR BEES EI 88 050808 inn Eun IB The installation procedure is the same for any of these drives The illustrations in this procedure show 3 5 inch SAS drives To install a hot swap hard disk drive complete the following steps Note If you have only one hard disk drive install it in the left or upper left drive bay Chapter 2 Installing optional devices 17 Attention To avoid damage to the hard disk drive connectors make sure that the cover is in place and fully closed whenever you install or remove a hard disk drive 1 AN gr ox Read the safety information that begins on page v and Make sure that the server cover is in place and fully closed Remove the filler panel from the bay Store it in a safe place for possible future use Attention To maintain proper system cooling do not operate the server for more than 10 minutes without either a drive or filler panel installed in each bay Open the drive tray handle H Gently push the drive assembly into the bay until the drive stops Close the drive tray handle Check the hard disk drive status LED to make sure that the hard disk drive is operating correctly If the amber hard disk drive status LED for a drive is lit continuously that drive is faulty and must be
3. fthe server passes the video diagnostics the video is good see Solving undetermined problems in the Hardware Maintenance Manual Trained service technician only If the server fails the video diagnostics replace the system board 50 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action The monitor has screen jitter or the screen image is wavy unreadable rolling or distorted uF If the monitor self tests show that the monitor is working correctly consider the location of the monitor Magnetic fields around other devices such as transformers appliances fluorescent lights and other monitors can cause screen jitter or wavy unreadable rolling or distorted screen images If this happens turn off the monitor Attention Moving a color monitor while it is turned on might cause screen discoloration Move the device and the monitor at least 305 mm 12 in apart and turn on the monitor Notes a To prevent disket
4. Problem determination Trained personnel are available to assist you with determining a hardware problem and deciding what action is necessary to fix the problem Hardware repair If the problem is caused by hardware under warranty trained Service personnel are available to provide the applicable level of service Engineering Change management There might be changes that are required after a product has been sold Lenovo or your reseller will make selected Engineering Changes ECs available that apply to your hardware These items are not covered by the warranty Replacement or use of parts not manufactured for or by Lenovo or non warranted Lenovo parts dentification of software problem sources Configuration of BIOS as part of an installation or upgrade Changes modifications or upgrades to device drivers Installation and maintenance of network operating systems NOS Installation and maintenance of application programs Refer to the safety and warranty information that is provided with your computer for a complete explanation of warranty terms You must retain your proof of purchase to obtain warranty service For a list of service and support phone numbers for your country or region go to http www lenovo com support and click Support phone list or refer to the safety and warranty information provided with your computer Note Phone numbers are subject to change without notice If the number for you
5. Do not leave open space above or below an installed server in your rack cabinet To help prevent damage to server components always install a filler panel to cover the open space and to help ensure proper air circulation See the documentation that comes with the rack cabinet for more information 3 Connect the cables and power cords See Connecting the cables on page 25 for more information 4 Update the server configuration See Updating the server configuration on page 26 26 for more information Installing the cover To install the cover place it into position and slide it forward Connecting the cables The following illustrations show the locations of the input and output connectors on the front and rear of the server Front e HO ABD wees Se E 6 USB 1 connector H USB 2 connector Chapter 2 Installing optional devices 25 Rear 9 200000000 L lo AA50G00000 Ses o anann 000 DOODOODOODOOODODODOODOO You Ethernet 1 connector Ethernet 2 connector Video connector Serial connector Power cord connector BH Systems management connector USB 3 connector an USB 4 connector ou fen must turn off the server before you connect or disconnect cables See the documentation that comes with any external devices for additional cabling instructions It might be easier for you to route cables before you connect
6. Do not allow your necktie or scarf to hang inside the server 12 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Remove jewelry such as bracelets necklaces rings and loose fitting wrist watches Remove items from your shirt pocket such as pens and pencils that might fall into the server as you lean over it Avoid dropping any metallic objects such as paper clips hairpins and screws into the server Handling static sensitive devices Attention Static electricity can damage the server and other electronic devices To avoid damage keep static sensitive devices in their static protective packages until you are ready to install them To reduce the possibility of damage from electrostatic discharge observe the following precautions Limit your movement Movement can cause static electricity to build up around you The use of a grounding system is recommended For example wear an electrostatic discharge wrist strap if one is available Always use an electrostatic discharge wrist strap or other grounding system when you work inside the server with the power on Handle the device carefully holding it by its edges or its frame Do not touch solder joints pins or exposed circuitry Do not leave the device where others can handle and damage it While the device is still in its static protective package touch it to an unpainted metal surface on the outside of the server for at least 2 seconds This d
7. For information about configuring the integrated Gigabit Ethernet controllers see the User s Guide 26 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Chapter 3 Server controls LEDs and power This chapter describes the controls and light emitting diodes LEDs and how to turn the server on and off Front view The following illustration shows the controls light emitting diodes LEDs and connectors on the front of the server WZ Bare e xj P Power on LED Power control button Reset button Hard disk drive activity LED Locator LED O B System Error LED USB 1 connector USB 2 connector CD drive activity LED CD eject button EE goong Power on LED When this LED is lit and not flashing it indicates that the server is turned on When this LED is flashing it indicates that the server is turned off and still connected to an ac power source When this LED is off it indicates that ac power is not present or the power supply or the LED itself has failed Note If this LED is off it does not mean that there is no electrical power in the server The LED might be burned out To remove all electrical power from the server you must disconnect the power cord from the electrical outlet Power control button Press this button to turn the server on and off manually A power control button shield comes installe
8. N 22 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Remote Supervisor Adapter II Mounting bracket SlimLine Mounting bracket aO Mounting bracket retention latch Read the safety information that begins on page v and Installation guidelines Turn off the server and peripheral devices and disconnect the power cord and all external cables Remove the cover If you have installed an optional PCI X riser card assembly disconnect the riser card power cable from the riser card assembly Grasp the riser card assembly at the front and rear edges and lift to remove it from the server Place the riser card assembly on a flat static protective surface Put the protective plastic cover that came with the adapter on the Remote Supervisor Adapter II SlimLine Turn the Remote Supervisor Adapter II SlimLine so that the keys on the connector align correctly with the connector on the system board Chapter 2 Installing optional devices 23 10 11 At a downward angle insert the free end of the adapter under the tab on the mounting bracket aligning the holes in the adapter with the posts on the mounting bracket Rotate the rear of the adapter into the rear mounting bracket aligning the holes in the adapter with the posts on the rear mounting bracket Press the Remote Supervisor Adapter II SlimLine firmly into the connector and make sure that all tabs on both mounting brackets se
9. Set and change the startup characteristics of the server and the order of startup devices startup drive sequence Set and change settings for advanced hardware features View and clear the event and error logs Change interrupt request IRQ settings Resolve configuration conflicts To start the Configuration Setup Utility program complete the following steps 1 2 3 Turn on the server When the message Press F1 for Configuration Setup is displayed press F1 If an administrator password has been set you must type the administrator password to access the full Configuration Setup Utility menu Follow the instructions on the screen See the User s Guide that is on the ThinkServer Documentation DVD for more information about using the Configuration Setup Utility program Using the LSI Logic Configuration Utility program Use the LSI Logic Configuration Utility program to configure hot swap hard disk drives that are connected to the SAS SATA controller Important If the server is a simple swap SATA model that contains a SATA RAID back plate you can use the LSI Logic Configuration Utility program to configure the simple swap SATA hard disk drives If you install an optional RAID controller in the server such as the ServeRAID MR10i controller use the configuration software that comes with the adapter to configure the hard disk drives To start the LSI Logic Configuration Utility program complete the following steps
10. 1 2 4 5 Turn on the server When the prompt Press CTRL C to start LSI Logic Configuration Utility is displayed press Ctrl C If you have set an administrator password you are prompted to type the password Use the arrow keys to select the adapter SAS controller for which you want to change settings Use the Help function to see instructions and available actions for this screen If you select SAS Topology or Advanced Adapter Properties additional screens are displayed To change the settings of the selected items follow the instructions on the screen Press Enter to save your changes 34 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Using the baseboard management controller The baseboard management controller provides basic environmental monitoring functions for the server If an environmental condition exceeds a threshold or if a system component fails the baseboard management controller lights LEDs to help you diagnose the problem and also records the error in the BMC system event log The baseboard management controller also provides command line interface remote server management capabilities through the Avocent SMBridge management utility program The command line interface provides direct access to server management functions through the Intelligent Platform Management Interface IPMI protocol Use the command line interface to issue commands to control the server power view sys
11. Maximum 0 55 kVA Notes 1 Power consumption and heat output vary depending on the number and type of optional features that are installed and the power management optional features that are in use 2 These levels were measured in controlled acoustical environments according to the procedures that are specified by the American National Standards Institute ANSI 12 10 and ISO 7779 and are reported in accordance with ISO 9296 Actual sound pressure levels in a given location might exceed the average stated values because of room reflections and other nearby noise sources The declared sound power levels indicate an upper limit below which a large number of computers will operate 3 There is no keyboard connector or mouse connector on the server You can connect a USB keyboard and USB mouse to the server by using the USB connectors 4 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Major components of the server Blue on a component indicates touch points where you can grip the component to remove it from or install it in the server open or close a latch and so on Orange on a component or an orange label on or near a component indicates that the component can be hot swapped which means that if the server and operating system support hot swap capability you can remove or install the component while the server is running Orange can also indicate touch points on hot swap components See the
12. Locate the documentation that comes with the hard disk drive and follow those instructions in addition to the instructions in this chapter Note The ID for an installed hard disk drive is on the front of the server next to the bay that contains the drive Chapter 2 Installing optional devices 15 Table 2 Locations of hard disk drive IDs 3 5 inch drive model servers EY Bo Emm Seen 2 I ca 188 J 2 5 inch drive model servers ird ponon BO nmi eRe D TERRE REDIO mm Feng EIER l cz JRR BE E PE Attention To avoid damage to the hard disk drive connectors make sure that the cover is in place and fully closed whenever you install or remove a hard disk drive Installing a simple swap Serial ATA hard disk drive Attention Simple swap hard disk drives are not hot swappable Disconnect all power from the server before you remove or install a simple swap hard disk drive To install a simple swap Serial ATA hard disk drive complete the following steps Note If you have only one hard disk drive install it in the left drive bay SATA hard disk drive back plate Hard disk drive assembly BH Filler panel Attention To avoid damage to the hard disk drive connectors make sure t
13. USB devices However you must turn off the server before performing any steps that involve removing or installing adapter cables or non hot swap optional devices or componenis Blue on a component indicates touch points where you can grip the component to remove it from or install it in the server open or close a latch and so on Orange on a component or an orange label on or near a component indicates that the component can be hot swapped which means that if the server and operating system support hot swap capability you can remove or install the component while the server is running Orange can also indicate touch points on hot swap components See the instructions for removing or installing a specific hot swap component for any additional procedures that you might have to perform before you remove or install the component When you are finished working on the server reinstall all safety shields guards labels and ground wires For a list of supported optional devices for the server see http www lenovo com System reliability guidelines To help ensure proper cooling and system reliability make sure that the following requirements are met Each of the drive bays has a drive or a filler panel and electromagnetic compatibility EMC shield installed in it If the server has redundant power each of the power supply bays has a power supply installed in it There is adequate space around the server to allow the server coo
14. and the reset button does work the server does not start Note The power control button will not function until 20 seconds after the server has been connected to ac power 1 Make sure that the power control button is working correctly a Disconnect the server power cords b Reconnect the power cords c Press the power control button d If the server does not start disconnect the server power cords and reseat the operator information panel cables then repeat steps 1b through 1c If the problem remains replace the operator information panel 2 Make sure that The ac power cord is correctly connected to the server and to a working electrical outlet The server contains the correct type of DIMMs The DIMMs are correctly seated Trained service technician only The microprocessor is correctly installed 3 If you just installed an optional device remove it and restart the server If the server now starts you might have installed more devices than the power supply supports 4 Reseat the following components a DIMMs b Trained service technician only Power supply cables to all internal components c Trained service technician only Power connector on the system board 5 Replace the following components one at a time in the order shown restarting the server each time a DIMMs b Trained service technician only Power supply c Trained service technician only System board 6 See
15. current and energy levels are present inside any component that has this label attached There are no serviceable parts inside these components If you suspect a problem with one of these parts contact a service technician Statement 26 A CAUTION Do not place any object on top of rack mounted devices This server is suitable for use on an IT power distribution system whose maximum phase to phase voltage is 240 V under any distribution fault condition Safety Xi Xii ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Chapter 1 Introduction This Installation Guide contains instructions for setting up your Lenovo ThinkServer RS110 Types 6435 6436 6437 and 6438 server and basic instructions for installing some optional devices More detailed instructions for installing optional devices are in the User Guide on the Lenovo ThinkServer Documentation DVD which comes with the server This document contains information about Setting up and cabling the server Starting and configuring the server Installing some optional devices Solving problems If firmware and documentation updates are available you can download them from the Lenovo Web site The server might have features that are not described in the documentation that comes with the server and the documentation might be updated occasionally to include information about those features or technical updates might be available to provide addi
16. MICH SM TWET Remarque Cette marque s applique uniquement aux pays de l Union Europ enne et la Norvege L etiquette du syst me respecte la Directive europ enne 2002 96 EC en mati re de D chets des Equipements Electriques et Electroniques DEEE qui d termine les dispositions de retour et de recyclage applicables aux syst mes utilis s travers Appendix B Notices 63 l Union europ enne Conform ment la directive ladite tiquette pr cise que le produit sur lequel elle est appos e ne doit pas tre jet mais tre r cup r en fin de vie In accordance with the European WEEE Directive electrical and electronic equipment EEE is to be collected separately and to be reused recycled or recovered at end of life Users of EEE with the WEEE marking per Annex IV of the WEEE Directive as shown above must not dispose of end of life EEE as unsorted municipal waste but use the collection framework available to customers for the return recycling and recovery of WEEE Customer participation is important to minimize any potential effects of EEE on the environment and human health due to the potential presence of hazardous substances in EEE For proper collection and treatment contact your local Lenovo representative Battery return program This product may contain a lithium or lithium ion battery Consult your user manual or service manual for specific
17. Make sure that installed does not work The device is designed for the server see http www lenovo com accessories You followed the installation instructions that came with the device and the device is installed correctly You have not loosened any other installed devices or cables You updated the configuration information in the Configuration Setup Utility program Whenever a device is changed you must update the configuration 2 Reseat the device that you just installed 3 Replace the device that you just installed An optional device that used to Make sure that all of the cable connections for the device are secure work does not work now i 1 j 2 f the device comes with test instructions use those instructions to test the device 3 Reseat the failing device 4 Replace the failing device 52 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Power problems Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which componenis are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action The power control button does not work
18. Ordinance for Work with Visual Display Units Das Produkt ist nicht f r den Einsatz an Bildschirmarbeitspl tzen im Sinne 2 der Bildschirmarbeitsverordnung geeignet Electronic emissions notices Federal Communications Commission FCC statement Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits Lenovo is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment Unauthorized changes or modifications could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference
19. and align it with the expansion slot in the riser card assembly then press the adapter firmly into the expansion slot Adapter bracket Tab Expansion slot bracket B Adapter Important Make sure that the U shaped opening in the metal adapter bracket engages the tab on the expansion slot bracket Follow the cabling instructions if any that come with the adapter Reinstall the riser card assembly Make sure that the riser card assembly is fully seated in the riser card connectors on the system board If you have installed an optional PCI X riser card assembly in the server reconnect the riser card power cable to the riser card assembly If you are installing a ServeRAID MR10i controller 2 5 inch drive models only complete the following steps Chapter 2 Installing optional devices 21 a Disconnect the existing SAS SATA controller signal cable from the hard disk drive backplane and from the controller then remove the cable from the server b Route the ServeRAID MR10i signal cable as shown in the following illustration and connect it to the hard disk drive backplane p PS Ss S Soll pi
20. are installed note the following Do not remove the covers Removing the covers of the laser product could result in exposure to hazardous laser radiation There are no serviceable parts inside the device Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure A DANGER Some laser products contain an embedded Class 3A or Class 3B laser diode Note the following Laser radiation when open Do not stare into the beam do not view directly with optical instruments and avoid direct exposure to the beam A Class 1 Laser Product Laser Klasse 1 Laser Klass 1 Luokan 1 Laserlaite Appareil A Laser de Classe 1 Safety IX Statement 4 A gt 18 kg 39 7 Ib gt 32 kg 70 5 Ib gt 55 kg 121 2 Ib CAUTION Use safe practices when lifting Statement 5 AA CAUTION The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device The device also might have more than one power cord To remove all electrical current from the device ensure that all power cords are disconnected from the power source AA 2 7 mp m Dep m X ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Statement 8 AA CAUTION Never remove the cover on a power supply or any part that has the following label attached Hazardous voltage
21. connect the monitor cable directly to the correct connector on the rear of the server 2 Make sure that The server is turned on If there is no power to the server see Power The monitor cables are connected correctly The monitor is turned on and the brightness and contrast controls are adjusted correctly Only a single beep sounds when the server is turned on Important In some memory configurations the 3 3 3 beep code might sound during POST followed by a blank monitor screen If this occurs and the Boot Fail Count option in the Start Options of the Configuration Setup Utility program is enabled you must restart the server three times to reset the configuration settings to the default configuration the memory connector or bank of connectors is enabled 3 Make sure that the correct server is controlling the monitor if applicable 4 Make sure that damaged BIOS code is not affecting the video see Recovering from BIOS update failure in the Hardware Maintenance Manual 5 See Solving undetermined problems in the Hardware Maintenance Manual The monitor works when you 1 Make sure that turn on the server but the Screen goes blank when you start some application programs You installed the necessary device drivers for the application The application program is not setting a display mode that is higher than the capability of the monitor 2 Run video diagnostics see the Hardware Maintenance Manual
22. customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Error code Description Action 162 Invalid configuration information or CMOS random access memory RAM checksum failure 1 Run the Configuration Setup Utility program select Load Default Settings and save the settings Reseat the battery Replace the battery 4 Trained service technician only Replace the system board 163 The time of day has not been set Run the Configuration Setup Utility program set the date and time and save the settings 164 Memory size has changed 1 Run the Configuration Setup Utility program then exit saving the configuration settings 2 Reseat the DIMMs 184 Power on password damaged 1 Run the Configuration Setup Utility program select Load Default Settings and save the settings Reseat the battery Replace the following components one at a time in the order shown restarting the server each time a Battery b Trained service technician only System board 187 VPD serial number not set 1 Reseat the optional Remote Supervisor Adapter II SlimLine 2 Trained service technician only Replace the system board 189 Three attempts were made to access the server with an
23. incorrect password Restart the server and enter the administrator password then run the Configuration Setup Utility program and change the power on password Chapter 5 Solving problems 39 Table 4 Abbreviated list of POST error codes continued Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Error code Description Action 289 A failing DIMM was disabled 1 Make sure that the DIMM is installed correctly see Installing a memory module on page 14 2 Reseat the DIMM 3 Replace the DIMM 178x Fixed disk error Note x is the drive that has the error 1 Run the hard disk drive diagnostic tests on drive x see Running the diagnostic programs in the Hardware Maintenance Manual on the ThinkServer Documentation DVD 2 Reseat the following components depending on the server model Hot swap models Hard disk drive x Simple swap models a Hard disk drive x b Hard disk drive x cable 3 Replace the following components one at a time depending on the server model in the or
24. instructions for removing or installing a specific hot swap component for any additional procedures that you might have to perform before you remove or install the component The following illustration shows the major components in the server Note The illustrations in this document might differ slightly from your hardware Chapter 1 Introduction 5 3 5 inch models Riser card assembly SAS SATA controller some models System board SAS SATA backplane some models SATA simple swap back panel some models Power supply Fans 3 5 inch drive cage BED BEE SE 6 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide 2 od fed n fed le gt ojoj 3 gt wln o Bezel 3 5 inch hot swap hard disk drive some models CD DVD drive Operator information panel assembly CD DVD interface card Fans Air baffle Microprocessor m m Fico 3 5 inch simple swap SATA hard disk drive some models Simple swap SATA filler panel Hot swap hard disk drive filler 22 Heat exchanger retention module Heat exchanger assembly DIMM Chapter 1 Introduction 7 2 5 inch models BEG 55 Riser card assembly SAS SATA controller some models System board 2 5 inch hard disk drive backplane Power supply Fans 2 5 inch drive cage 2 5 inch drive hard disk drive 2 5 inch filler panel Bezel 8 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide 2 ad feed Weed
25. processor is shut down however the server can respond to requests from the service processor the baseboard management controller such as a remote request to turn on the server Turning on the server Approximately 20 seconds after the server is connected to ac power the power control button becomes active and one or more fans might start running to provide cooling while the server is connected to power You can turn on the server and start the operating system by pressing the power control button The server can also be turned on in any of the following ways f a power failure occurs while the server is turned on the server will restart automatically when power is restored f your operating system supports the systems management software for an optional Remote Supervisor Adapter II SlimLine the systems management software can turn on the server f your operating system supports the Wake on LAN feature the Wake on LAN feature can turn on the server Note When 4 GB or more of memory physical or logical is installed some memory is reserved for various system resources and is unavailable to the operating system The amount of memory that is reserved for system resources depends on the operating system the configuration of the server and the configured PCI optional devices Turning off the server When you turn off the server and leave it connected to ac power the server can respond to requests from the service pro
26. that the memory configuration has changed 14 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide To install a DIMM or l complete the following steps 1 Read the safety information that begins on page VJand Installation guidelines on page 11 2 Turn off the server and peripheral devices and disconnect the power cord and all external cables Remove the cover Attention To avoid breaking the retaining clips or damaging the DIMM connectors open and close the clips gently 3 Open the retaining clip on each end of the DIMM connector 4 Touch the static protective package that contains the DIMM to any unpainted metal surface on the outside of the server Then remove the DIMM from the package 5 Turn the DIMM so that the keys align correctly with the slot 6 Insert the DIMM into the connector by aligning the edges of the DIMM with the slots at each end of the DIMM connector Firmly press the DIMM straight down into the connector by applying pressure on both ends of the DIMM simultaneously The retaining clips snap into the locked position when the DIMM is firmly seated in the connector If there is a gap between the DIMM and the retaining clips the DIMM has not been correctly inserted open the retaining clips remove the DIMM and then reinsert it If you have other devices to install do so now Otherwise go to Completing the installation on page 24 Installing a hard disk drive
27. the devices to the server Cable identifiers are printed on the cables that come with the server and devices Use these identifiers to connect the cables to the correct connectors If the server comes with an installed operating system see the documentation that comes with the operating system for additional cabling instructions There is no keyboard connector or mouse connector on the server You can connect a USB keyboard and USB mouse to the server by using the USB connectors Updating the server configuration When you start the server for the first time after you add or remove an internal optional device or external SAS device you might receive a message that the configuration has changed The Configuration Setup Utility program starts automatically so that you can save the new configuration settings For more information see Chapter 4 Configuring the server on page 31 Some optional devices have device drivers that you must install For information about installing device drivers see the documentation that comes with each device If the server has a RAID configuration that uses the SAS SATA controller with integrated RAID and you have installed or removed a hard disk drive you might have to reconfigure the disk arrays If the server has an optional RAID adapter and you have installed or removed a hard disk drive see the documentation that comes with the RAID adapter for information about reconfiguring the disk arrays
28. 000 bytes Total user accessible capacity can vary depending on operating environments Maximum internal hard disk drive capacities assume the replacement of any standard hard disk drives and population of all hard disk drive bays with the largest currently supported drives that are available from Lenovo Maximum memory might require replacement of the standard memory with an optional memory module Lenovo makes no representation or warranties regarding non Lenovo products and services including but not limited to the implied warranties of merchantability and fitness for a particular purpose These products are offered and warranted solely by third parties 62 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Lenovo makes no representations or warranties with respect to non Lenovo products Support if any for the non Lenovo products is provided by the third party not Lenovo Some software might differ from its retail version if available and might not include user manuals or all program functionality Waste electrical and electronic equipment WEEE notices This unit must be recycled or discarded according to applicable local and national regulations Lenovo encourages owners of information technology IT equipment to responsibly recycle their equipment when it is no longer needed Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products Information on Lenovo
29. 8 vi Antes de instalar este producto lea la informaci n de seguridad Las sakerhetsinformationen innan du installerar den har produkten Important Each caution and danger statement in this document is labeled with a number This number is used to cross reference an English language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document For example if a caution statement is labeled Statement 1 translations for that caution statement are in the Safety Information document under Statement 1 Be sure to read all caution and danger statements in this document before you perform the procedures Read any additional safety information that comes with the server or optional device before you install the device ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Statement 1 AA DANGER Electrical current from power telephone and communication cables is hazardous To avoid a shock hazard Do not connect or disconnect any cables or perform installation maintenance or reconfiguration of this product during an electrical storm Connect all power cords to a properly wired and grounded electrical outlet Connect to properly wired outlets any equipment that will be attached to this product When possible use one hand only to connect or disconnect signal cables Never turn on any equipment when there is evi
30. If a USB hub is in use disconnect the USB device from the hub and connect it directly to the server 3 Move the mouse or pointing device cable to another USB connector 4 Replace the following components one at a time in the order shown restarting the server each time a Mouse or pointing device b Only if the problem occurred with a front USB connector Internal cables to the operation information panel c Only if the problem occurred with a front USB connector Operator information panel Trained service technician only System board 2 48 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Memory problems Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which componenis are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action The amount of system memory that is displayed is less than the amount of installed physical memory ilc Make sure that No error LEDs are lit on the operator information panel The memory modules are seated correctly You have installed the correct type of memory see Installing a memory module
31. Solving undetermined problems in the Hardware Maintenance Manual The server does not turn off 1 Determine whether you are using an Advanced Configuration and Power Interface ACPI or a non ACPI operating system If you are using a non ACPI operating system complete the following steps a Press Ctrl Alt Delete b Turn off the server by pressing the power control button for 5 seconds c Restart the server d If the server fails POST and the power control button does not work disconnect the ac power cord for 20 seconds then reconnect the ac power cord and restart the server 2 If the problem remains or if you are using an ACPl aware operating system The server unexpectedly shuts down and the LEDs on the operator information panel are not lit suspect the system board Call for service Chapter 5 Solving problems 53 Serial device problems Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which componenis are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action The number of serial ports that 4 Make sure that are identified by the operating Each port is assigned a uni
32. T detects a problem during startup other beep codes might occur Use the following beep code descriptions to help diagnose and solve problems that are detected during startup Note See the Hardware Maintenance Manual on the ThinkServer Documentation DVD for more information about the POST beep codes One beep POST was completed successfully without detecting any errors Other beep codes See the Hardware Maintenance Manual on the ThinkServer Documentation DVDD for information about other beep codes Lenovo 2008 Portions IBM Corp 2008 37 POST error codes The following table provides an abbreviated list of the error codes that might appear during POST See the Hardware Maintenance Manual on the ThinkServer Documentation DVD for more information about the POST error codes To check for updated technical information complete the following steps Note Changes are made periodically to the Lenovo Web site The actual procedure might vary slightly from what is described in this document T 2 Go to http www lenovo com support Enter your product number machine type and model number or select Servers from the Select your product list Select Servers from the Brand list From Family list select ThinkServer RS110 and click Continue Click User s guides and manuals for documentation Table 4 Abbreviated list of POST error codes Follow the suggested actions in the order in which they are listed in the Action col
33. ThinkServer RS 110 Types 6435 6436 6437 and 6438 lenovo Installation Guide ThinkServer RS 110 Types 6435 6436 6437 and 6438 lenovo Installation Guide Note Before using this information and the product it supports read the general information in Appendix B Notices on page 61 and the Warranty and Support Information document on the Lenovo ThinkServer Documentation DVD First Edition October 2008 Copyright Lenovo 2008 Portions Copyright International Business Machines Corporation 2008 All rights reserved LENOVO products data computer software and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C F R 2 101 with limited and restricted rights to use reproduction and disclosure LIMITED AND RESTRICTED RIGHTS NOTICE If products data computer software or services are delivered pursuant a General Services Administration GSA contract use reproduction or disclosure is subject to restrictions set forth in Contract No GS 35F 05925 Contents Safety Chapter 1 Introduction The Lenovo ThinkServer Documentation DVD Hardware and software requirements Notices and statements in this document Features and specifications Major components of the server System board optional device connectors Chapter 2 Installing optional devices Installation guidelines RA System reliability guidelines Working ins
34. alled or that a 19990305 error code is displayed indicating that an operating system was not found but the server is otherwise working correctly If the server is not working correctly see Chapter 5 Solving problems on page 37 for diagnostic information Observe good housekeeping in the area where you are working Place removed covers and other parts in a safe place f you must start the server while the cover is removed make sure that no one is near the server and that no tools or other objects have been left inside the server Do not attempt to lift an object that you think is too heavy for you If you have to lift a heavy object observe the following precautions Make sure that you can stand safely without slipping Distribute the weight of the object equally between your feet Use a slow lifting force Never move suddenly or twist when you lift a heavy object To avoid straining the muscles in your back lift by standing or by pushing up with your leg muscles Make sure that you have an adequate number of properly grounded electrical outlets for the server monitor and other devices Back up all important data before you make changes to disk drives Have a small flat blade screwdriver available Lenovo 2008 Portions IBM Corp 2008 11 You do not have to turn off the server to install or replace hot swap fans redundant hot swap ac power supplies or hot plug Universal Serial Bus
35. and 2 this device must accept any interference received including interference that may cause undesired operation Industry Canada Class A emission compliance statement This Class A digital apparatus complies with Canadian ICES 003 Appendix B Notices 65 Avis de conformit la r glementation d Industrie Canada Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada Australia and New Zealand Class A statement Attention This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures United Kingdom telecommunications safety requirement Notice to Customers This apparatus is approved under approval number NS G 1234 J 100003 for indirect connection to public telecommunication systems in the United Kingdom European Union EMC Directive conformance statement This product is in conformity with the protection requirements of EU Council Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non recommended modification of the product including the fitting of non Lenovo option cards This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to CISPR 22 European Standard EN 55022 T
36. ard do not work See http www lenovo com accessories for keyboard compatibility 2 Make sure that The keyboard cable is securely connected The server and the monitor are turned on 3 Move the keyboard cable to a different USB connector 4 Replace the following components one at a time in the order shown restarting the server each time a Keyboard b Only if the problem occurred with a front USB connector Internal cables to the operation information panel c Only if the problem occurred with a front USB connector Operator information panel 2 Trained service technician only System board Chapter 5 Solving problems 47 Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action The USB mouse or USB 1 Make sure that ointing device does not work i f P 9 The mouse is compatible with the server See http www lenovo com The mouse or pointing device USB cable is securely connected to the server and the device drivers are installed correctly The server and the monitor are turned on 2
37. battery information The battery must be recycled or disposed of properly Recycling facilities may not be available in your area For information on disposal or batteries outside the United States go to http www lenovo com lenovo environment or contact your local waste disposal facility For Taiwan Please recycle batteries HERE For the European Union Notice This mark applies only to countries within the European Union EU Batteries or packaging for batteries are labeled in accordance with European Directive 2006 66 EC concerning batteries and accumulators and waste batteries and accumulators The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union This label is applied to various batteries to indicate that the battery is not to be thrown away but rather reclaimed upon end of life per this Directive Les batteries ou emballages pour batteries sont tiquet s conform ment aux directives europ ennes 2006 66 EC norme relative aux batteries et accumulateurs en usage et aux batteries et accumulateurs us s Les directives d terminent la marche suivre en vigueue dans l Union Europ enne pour le retour et le recyclage des batteries et accumulateurs us s Cette tiquette est appliqu e sur diverses batteries pour indiquer que la batterie ne doit pas tre mise au rebut mais plut t r cup r e en fin de cycle de vie selon cette norme In acc
38. blem situations 2 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Attention These notices indicate potential damage to programs devices or data An attention notice is placed just before the instruction or situation in which damage might occur Caution These statements indicate situations that can be potentially hazardous to you A caution statement is placed just before the description of a potentially hazardous procedure step or situation Danger These statements indicate situations that can be potentially lethal or extremely hazardous to you A danger statement is placed just before the description of a potentially lethal or extremely hazardous procedure step or situation Features and specifications The following information is a summary of the features and specifications of the server Depending on the server model some features might not be available or some specifications might not apply Racks are marked in vertical increments of 4 45 cm 1 75 inches Each increment is referred to as a unit or U A 1 U high device is 1 75 inches tall Chapter 1 Introduction 3 Table 1 Features and specifications Microprocessor One Intel LGA 775 single core dual core or quad core depending on the server model Single core Celeron 440 or later Dual core Core 2 Duo E4600 or Xeon E3110 or later Quad core Xeon 3300 series Notes 1 Use the Configuration Setup Utility pro
39. bootable found operating system is installed 2 Run the hard disk drive diagnostic tests 3 Reseat the following components a Hard disk drive b CD or DVD drive and cables c Trained service technician only System board 4 Replace the components listed in step 3 one at a time in the order shown restarting the server each time 19990650 AC power has been restored 1 Check the power cables 2 Check for interruption of the power supply 44 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Troubleshooting tables Use the troubleshooting tables to find solutions to problems that have identifiable symptoms See the Hardware Maintenance Manual on the Lenovo ThinkServer Documentation DVD for more detailed troubleshooting information If you cannot find a problem in these tables run the diagnostic programs see Running the diagnostic programs in the Hardware Maintenance Manual If you have just added new software or a new optional device and the server is not working complete the following steps before you use the troubleshooting tables 1 Check the system error LED on the operator information panel see Chapter 3 Server controls LEDs and power on page 27 2 Remove the software or device that you just added 3 Run the diagnostic tests to determine whether the server is running correctly 4 Reinstall the new software or new device CD or DVD drive problems Follow t
40. cessor such as a remote request to turn on the server While the server remains connected to ac power one or more fans might continue to run To remove all power from the server you must disconnect it from the power source Some operating systems require an orderly shutdown before you turn off the server See your operating system documentation for information about shutting down the operating system Chapter 3 Server controls LEDs and power 29 Statement 5 AA CAUTION The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device The device also might have more than one power cord To remove all electrical current from the device ensure that all power cords are disconnected from the power source AA 20a 1S The server can be turned off in any of the following ways You can turn off the server from the operating system if your operating system supports this feature After an orderly shutdown of the operating system the server will be turned off automatically You can press the power control button to start an orderly shutdown of the operating system and turn off the server if your operating system supports this feature If the operating system stops functioning you can press and hold the power control button for more than 4 seconds to turn off the server If an optional Remote Supervisor Adapter II SlimLine is installed in the server
41. che Vertraglichkeit von Betriebsmitteln EMVG fr her Gesetz Uber die elektromagnetische Vertr glichkeit von Ger ten Dies ist die Umsetzung der EU Richtlinie 2004 108 EG fr her 89 336 EWG in der Bundesrepublik Deutschland Zulassungsbescheinigung laut dem Deutschen Gesetz ber die elektromagnetische Vertr glichkeit von Betriebsmitteln EMVG vom 20 Juli 2007 fr her Gesetz ber die elektromagnetische Vertr glichkeit von Ger ten bzw der EMV EG Richtlinie 2004 108 EC fr her 89 336 EWG f r Ger te der Klasse A Dieses Ger t ist berechtigt in bereinstimmung mit dem Deutschen EMVG das EG Konformit tszeichen CE zu f hren Verantwortlich f r die Konformit tserkl rung nach Paragraf 5 des EMVG ist die Lenovo Deutschland GmbH Gropiusplatz 10 D 70563 Stuttgart Informationen in Hinsicht EMVG Paragraf 4 Abs 1 4 Das Ger t erf llt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A Nach der EN 55022 Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen in diesem Fall kann vom Betreiber verlangt werden angemessene Ma nahmen durchzuf hren und daf r aufzukommen Nach dem EMVG Ger te d rfen an Orten f r die sie nicht ausreichend entst rt sind nur mit besonderer Genehmigung des Bundesministers f r Post und Telekommunikation oder des Bundesamtes f r Post und Telekommunikation betrieben werden Die Genehmigung wird erteilt wenn
42. ctivity 28 Ethernet activity 28 Ethernet link 28 hard disk drive activity 27 locator 27 power on 27 system error 27 LEDs front 27 rear 28 locator LED 27 M major components 5 memory installing 14 order of installation 14 specifications 4 memory module installation 14 specifications 14 memory problems 49 microprocessor problems 49 type 4 monitor problems 50 mouse problems 48 N noise emissions 4 notes 2 notes important 62 notices and statements 2 O online documentation 1 online publications 1 optional device problems 52 optional device connectors 9 order of installation memory modules 14 P pointing device problems 48 power problems 53 requirement 4 supply 4 power control button 27 button shield 27 power cord connector 28 power on LED 27 power on self test POST error messages 38 problems CD ROM DVD ROM drive 45 hard disk drive 46 intermittent 47 keyboard 47 memory 49 microprocessor 49 monitor 50 optional devices 52 power 53 serial port 54 software 55 solving 37 USB port 56 video 56 R reset button 27 riser card connector location 9 removing 20 slots 9 S SAS hard disk drives installing 17 hot swap drives 4 hot swap models 4 SATA hot swap 4 hot swap hard disk drives installing 17 simple swap 4 simple swap hard disk drives installing 16 serial connector 28 serial port problems 54 serial attached SCSI See SAS server configuring 32 simple
43. cure the adapter in place Attention Incomplete insertion might cause damage to the server or the adapter If a three quarter length adapter is installed in expansion slot 1 on the riser card assembly remove it You can replace it with a half length adapter if you choose to do so Reinstall the riser card assembly Make sure that the riser card assembly is fully seated in the riser card connectors on the system board If you have installed an optional PCI X riser card assembly reconnect the riser card power cable to the riser card assembly See the documentation that comes with the Remote Supervisor Adapter II SlimLine for information about installing the firmware and configuring the adapter Create a backup copy of the configuration so that if you have to replace the adapter in the future you can restore the configuration If you have other devices to install do so now Otherwise go to Completing the installation Completing the installation To complete the installation complete the following steps 1 2 Install the cover See Installing the cover on page 25 for more information Install the server in the rack cabinet See the Rack Installation Instructions that come with the server for detailed information about how to install the server in a rack cabinet 24 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Attention Install the server only in a rack cabinet that has perforated doors
44. d around the button to prevent the server from being turned off accidentally You can remove this disk shaped shield if you prefer Reset button Press this button to reset the server and run the power on self test POST You might have to use a pen or the end of a straightened paper clip to press the button Hard disk drive activity LED When this LED is flashing it indicates that a hard disk drive is in use Locator LED This LED can be lit remotely by the system administrator to aid in visually locating the server System error LED When this LED is lit it indicates that a system error has occurred An LED on the system board might also be lit to help isolate the error See Chapter 5 Solving problems on page 37 for additional information Lenovo 2008 Portions IBM Corp 2008 27 USB connectors Connect a USB device to either of these connectors CD eject button Press this button to release a CD from the CD drive CD drive activity LED When this LED is lit it indicates that the CD drive is in use Rear view The following illustration shows the LEDs on the rear of the server 9 EHEHEHERUEOR 2 5AAS00000000000 oogog gt gt BEBE Er O00 G0000000000000000 Ethernet 1 activity LED Ethernet 2 activity LED BH Ethernet 1 link LED 4 Ethernet 2 link LED Ethernet activity LED This LED is on each Ethernet connector When this LED is lit it indicat
45. dence of fire water or structural damage Disconnect the attached power cords telecommunications systems networks and modems before you open the device covers unless instructed otherwise in the installation and configuration procedures Connect and disconnect cables as described in the following table when installing moving or opening covers on this product or attached devices To Connect To Disconnect 1 Turn everything OFF 1 Turn everything OFF 2 First attach all cables to devices 2 First remove power cords from outlet 3 Attach signal cables to connectors 3 Remove signal cables from connectors 4 Attach power cords to outlet 4 Remove all cables from devices 5 Turn device ON Safety vii Statement 2 A CAUTION When replacing the lithium battery use only the battery recommended by the manufacturer If your system has a module containing a lithium battery replace it only with the same module type made by the same manufacturer The battery contains lithium and can explode if not properly used handled or disposed of Do not Throw or immerse into water Heat to more than 100 C 212 F Repair or disassemble Dispose of the battery as required by local ordinances or regulations Viii ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Statement 3 A CAUTION When laser products such as CD ROMs DVD drives fiber optic devices or transmitters
46. der shown restarting the server each time Hot swap models a Hard disk drive x b Hard disk drive backplane c Trained service technician only System board Simple swap models a Hard disk drive x b Hard disk drive x cable c Trained service technician only System board 180x A PCI adapter requested a resource that is not available 40 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Run the Configuration Setup Utility program and make sure that the resources that are needed by the PCI adapter are available Table 4 Abbreviated list of POST error codes continued Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Error code Description Action 1962 A hard disk drive does not contain a valid boot sector 1 Make sure that a startable operating system is installed 2 Run the hard disk drive diagnostic tests 3 Reseat the following components a Hard disk drive b Hard disk drive backplane cable or back plate cables 4 Replace the following components one at a ti
47. e or imply that only that Lenovo product program or service may be used Any functionally equivalent product program or service that does not infringe any Lenovo intellectual property right may be used instead However it is the user s responsibility to evaluate and verify the operation of any other product program or service Lenovo may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to Lenovo United States Inc 1009 Think Place Building One Morrisville NC 27560 U S A Attention Lenovo Director of Licensing LENOVO PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication Lenovo may make improvements and or changes in the product s and or the program s described in this publication at any time without notice The products described in this d
48. e that the server supports the microprocessor Trained service technician only Make sure that the microprocessor is seated correctly Trained service technician only Replace the microprocessor Chapter 5 Solving problems 49 Monitor problems Some monitors have their own self tests If you suspect a problem with your monitor see the documentation that comes with the monitor for instructions for testing and adjusting the monitor Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action Testing the monitor 1 Make sure that the monitor cables are firmly connected 2 Try using a different monitor on the server or try testing the monitor on a different server 3 Run the diagnostic programs see the Hardware Maintenance Manual If the monitor passes the diagnostic programs the problem might be a video device driver 4 Trained service technician only Replace the system board The screen is blank 1 If the server is attached to a KVM switch bypass the KVM switch to eliminate it as a possible cause of the problem
49. ed We gt efje e 73 Exc E53 E83 ES eS px um CD DVD drive 3 5 inch hot swap hard disk drive some models Operator information panel assembly Fans Air baffle Microprocessor Heat exchanger retention module Heat exchanger assembly DIMM System board optional device connectors The following illustration shows the connectors for user installable optional devices n T TI Bin TIM BIB E en ra ul H 7 see Ba L m Mg p SAS SATA T controller b card i B u o o tB m yp is ej Ln Other systems management Dm DIMM 3 connector connector Remote Supervisor Adapter II DIMM 2 connector SlimLine connector Battery connector H DIMM 1 connector SAS SATA controller connector g Riser card connector DIMM 4 connector BES N The following illustration shows the locations of the PCI Express slots on the riser card assembly PCI Express x8 slot 1 H PCI Express x8 slot 2 Chapter 1 Introduction 9 10 rhinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Chapter 2 Installing opt
50. es that there is activity between the server and the network Ethernet link LED This LED is on each Ethernet connector When this LED is lit it indicates that the Ethernet controller is connected to the network The following illustration shows the connectors on the rear of the server DBBOBBOBEB AG50G00000 288 QUOUOOUROSo00050o 000 00000000000000000 Ethernet 1 connector Ethernet 2 connector Video connector Serial connector Power cord connector Systems management connector USB 3 connector USB 4 connector SENSE EBSEE Power cord connector Connect the power cord to this connector Serial connector Connect a 9 pin serial device to this connector Video connector Connect a monitor to this connector Ethernet connector Use either of these connectors to connect the server to a network Ethernet connector 1 supports Serial over LAN SOL USB connector Connect a USB device to either of these connectors 28 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Systems management connector Connect the server to a network for systems management information control This connector is active only if you have installed a Remote Supervisor Adapter II SlimLine and it is used only by the Remote Supervisor Adapter II SlimLine Server power features When the server is connected to an ac power source but is not turned on the operating system does not run and all core logic except for the service
51. from the Select your product list 3 Select Servers from the Brand list 4 From Family list select ThinkServer RS110 and click Continue Chapter 4 Configuring the server 35 36 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Chapter 5 Solving problems This chapter provides basic troubleshooting information to help you solve some common problems that might occur while you are setting up the server If you cannot locate and correct a problem by using the information in this chapter see Appendix A Getting help and technical assistance on page 57 the Hardware Maintenance Manual on the ThinkServer Documentation DVD Diagnostic tools overview The following tools are available to help you diagnose and solve hardware related problems POST beep codes The power on self test beep codes indicate the detection of a problem One beep indicates successful completion of POST with no errors More than one beep indicates that POST detected a problem Error messages also appear during startup if POST detects a hardware configuration problem See POST beep codes and the Hardware Maintenance Manual on the ThinkServer Documentation DVD for more information Troubleshooting charts These charts list problem symptoms and actions to correct the problems See Troubleshooting tables on page 45 for more information POST beep codes POST emits one beep to signal successful completion If POS
52. gram to determine the size of the L2 cache type and speed of the microprocessor and speed of the front side bus 2 Intel Virtualization Technology VT is not available on the Celeron 440 or the Core 2 Duo E4600 however these microprocessors can run paravirtualization Memory Minimum Two 512 MB DIMMs Maximum 8 GB Type PC2 5300 667 MHz ECC DDR II unbuffered SDRAM DIMMs Slots Four dual inline Supports 512 MB 1 GB and 2 GB DIMMs Drives Ultrabay Enhanced CD or CD DVD Expansion bays One of the following configurations Two 3 5 inch slim high bays for hard disk drives Hot swap models Supports maximum of two serial attached SCSI SAS drives or two serial ATA SATA drives Simple swap models Supports maximum of two SATA drives Four 2 5 inch small form factor SFF hot swap bays for hard disk drives Supports a maximum of four 2 5 inch SAS drives Expansion slots Two PCI Express x8 slots one low profile and one 3 4 length full height Low profile slot supports x4 electrical Video controller ATI ES1000 video on system board 16 MB DDR II video memory Power supply 351 watt 110 or 220 V ac auto sensing Size Height 43 mm 1 75 inches 1 U Depth 559 mm 22 inches Width 440 mm 17 32 inches Maximum weight 12 7 kg 28 Ib depending on your configuration Integrated functions Two Broadcom NetXtreme GB Ethernet controllers on the
53. half length adapter in the PCI X slot The optional Remote Supervisor Adapter II SlimLine can be installed only in the dedicated connector on the system board cee syster Board optionaldeviee connectors on page 9 for the location of the connector To install the Remote Supervisor Adapter II SlimLine soe instsling an IBM Remote Supervisor Adapter II SlimLine on page 22 The server uses a rotational interrupt technique to configure PCI Express adapters so that you can install PCI Express adapters that do not support sharing of interrupts 18 _ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide An optional ServeRAID MR10i controller provides RAID level 5 support to the 2 5 inch hot swap drives and supports an external storage enclosure A ServeRAID MR10i controller supports the 2 5 inch hard disk drives without modification An optional SAS HBA Controller adapter enables you to connect external storage devices such as SAS or SATA hard disk drives or tape drives to a simple swap SATA model server The server scans the PCI slots to assign system resources The scan sequence is related to the startup sequence If you have not changed the default startup sequence the server scans the PCI slots in the following order the integrated Ethernet controllers 1 and 2 then the drives that are connected to the SAS SATA controller then PCI Express slots 1 and 2 Expansion slot cover Bn Expansion slot BE Ada
54. hat the cover is in place and fully closed whenever you install or remove a hard disk drive 1 Read the safety information that begins on page vjand Installation guidelines on page 11 2 Make sure that the server cover is in place and fully closed 3 Turn off the server and peripheral devices and disconnect the power cord and all external cables 4 Remove the filler panel from the bay 5 Pull the loops of the tray toward each other and slide the drive into the server until the drive connects to the back panel 16 rhinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide 6 Insert the filler panel into the bay to cover the drive Notes 1 If a RAID controller or adapter is installed you might have to reconfigure the disk arrays after you install hard disk drives See your RAID controller or adapter documentation 2 To remove a simple swap SATA drive from the bay make sure that the server is turned off and the power cord is removed then remove the filler panel pull the loops of the drive tray toward each other and pull the tray out of the bay If you have other devices to install do so now Otherwise go to Completing the installation on page 24 Installing a hot swap hard disk drive The 3 5 inch drive hot swap server models support either two SAS 3 5 inch hard disk drives or two SATA 3 5 inch hard disk drives The 2 5 inch drive hot swap server models support four 2 5 inch SAS hard disk drives
55. he limits for Class A equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment Attention This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures German Class A compliance statement Deutschsprachiger EU Hinweis Hinweis f r Ger te der Klasse A EU Richtlinie zur Elektromagnetischen Vertr glichkeit Dieses Produkt entspricht den Schutzanforderungen der EU Richtlinie 2004 108 EG fr her 89 336 EWG zur Angleichung der Rechtsvorschriften ber die elektromagnetische Vertr glichkeit in den EU Mitgliedsstaaten und h lt die Grenzwerte der EN 55022 Klasse A ein Um dieses sicherzustellen sind die Ger te wie in den Handb chern beschrieben zu installieren und zu betreiben Des Weiteren d rfen auch nur von der Lenovo empfohlene Kabel angeschlossen werden Lenovo bernimmt keine Verantwortung f r die Einhaltung der Schutzanforderungen wenn das Produkt ohne Zustimmung der Lenovo ver ndert bzw wenn Erweiterungskomponenten von Fremdherstellern ohne Empfehlung der Lenovo gesteckt eingebaut werden Deutschland 66 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Einhaltung des Geseizes Uber die elektromagnetische Vertraglichkeit von Betriebsmittein Dieses Produkt entspricht dem Gesetz Uber die elektromagnetis
56. he operating system or program Using the documentation Information about your Lenovo system and preinstalled software if any or optional device is available in the documentation that comes with the product That documentation can include printed documents online documents readme files and help files Most of the documentation for your server is on the ThinkServer Documentation DVD provided with your server See the troubleshooting information in your system documentation for instructions for using the diagnostic programs The troubleshooting information or the diagnostic programs might tell you that you need additional or updated device drivers or other software Lenovo maintains pages on the World Wide Web where you can get the latest technical information and download device drivers and updates To access these pages go to http www lenovo com support and follow the instructions Lenovo 2008 Portions IBM Corp 2008 57 Getting help and information from the World Wide Web On the World Wide Web the Lenovo Web site has up to date information about Lenovo systems optional devices services and support For general information about Lenovo products or to purchase Lenovo products go_to For support on Lenovo products go to support Calling for service During the warranty period you can get help and information by telephone through the Customer Support Center These services are available during the warranty period
57. he suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action The CD or DVD drive is not recognized il Make sure that All cables and jumpers are installed correctly The signal cable and connector are not damaged and the connector pins are not bent All damaged parts are repaired or replaced The correct device driver is installed for the CD or DVD drive Run the CD CD RW or DVD drive diagnostic programs Reseat the following components a CD or DVD drive b CD or DVD interface board cable Replace the following components one at a time in the order shown restarting the server each time a CD or DVD drive b CD or DVD drive interface board cable c CD or DVD interface board d Trained service technician only System board A CD or DVD is not working correctly Ponn Clean the CD or DVD Run the CD or DVD drive diagnostic programs Reseat the CD or DVD drive Replace the CD or DVD drive Chapter 5 Solving problems 45 Follow the suggested actions in the order in which they are listed in
58. ich they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action A problem occurs only occasionally and is difficult to diagnose 1 Make sure that All cables and cords are connected securely to the rear of the server and attached devices When the server is turned on air is flowing from the fan grille If there is no airflow the fan is not working This can cause the server to overheat and shut down 2 Check the system error logs see Using the Configuration Setup Utility program on page 34 ogram on page 34 USB keyboard mouse or pointing device problems Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action All or some keys on the keybo
59. ide the server with the power on Handling static sensitive devices Removing the cover Installing a memory module Installing a hard disk drive Installing a simple swap Serial ATA hard disk drive Installing a hot swap hard disk drive Installing an adapter Installing an IBM Remote Supervisor Adapter II SlimLine Completing the installation Installing the cover Connecting the cables Updating the server configuration Chapter 3 Server controls LEDs and power Front view Eu scu RES Rear view Server power features Turning on the server Turning off the server Chapter 4 Configuring the server Using the ThinkServer EasyStartup program Using ThinkServer EasyManage products Using the Configuration Setup Utility program Using the LSI Logic Configuration Utility program Using the baseboard management controller Configuring the Gigabit Ethernet controllers Chapter 5 Solving problems Diagnostic tools overview POST beep codes POST error codes Troubleshooting tables CD or DVD drive problems General problems Hard disk drive problems Intermittent problems USB keyboard mouse or pointing device problems Memory problems Lenovo 2008 Portions IBM Corp 2008 Microprocessor problems Monitor problems Optional device problems Power problems Serial device problems EasyStartup problems Software problems Universal Serial Bus USB device problems Video pr
60. ilable go to http www lenovo com support click Warranty and follow the instructions on the screen For technical assistance with the installation of or questions related to Service Packs for your preinstalled Microsoft Windows product refer to the Microsoft Product Support Services Web site at http www support microsoft com directory or you can contact the Customer Support Center Some fees might apply Purchasing additional services During and after the warranty period you can purchase additional services such as support for hardware operating systems and application programs network setup and configuration upgraded or extended hardware repair services and custom installations Service availability and service name might vary by country or region For more information about these services go to the Lenovo Web site at http www lenovo com Lenovo product service FE Lenovo hk BA 7A W T HAR EEL BE BR BI Abr a Be SET BEC i rI ARISES FE 0800 000 700 Appendix A Getting help and technical assistance 59 60 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Appendix B Notices Lenovo may not offer the products services or features discussed in this document in all countries Consult your local Lenovo representative for information on the products and services currently available in your area Any reference to a Lenovo product program or service is not intended to stat
61. imated through extrapolation Actual results may vary Users of this document should verify the applicable data for their specific environment The following terms are trademarks of Lenovo in the United States other countries or both Lenovo Lenovo logo ThinkServer The following terms are trademarks of International Business Machines Corporation in the United States other countries or both IBM Wake on LAN ServeRAID Intel is a trademark or registered trademarks of Intel Corporation in the United States other countries or both Microsoft and Windows are trademarks of Microsoft Corporation in the United States other countries or both Adobe and PostScript are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States other countries or both Other company product or service names may be trademarks or service marks of others Important notes Processor speed indicates the internal clock speed of the microprocessor other factors also affect application performance CD or DVD drive speed is the variable read rate Actual speeds vary and are often less than the possible maximum When referring to processor storage real and virtual storage or channel volume KB stands for 1024 bytes MB stands for 1 048 576 bytes and GB stands for 1 073 741 824 bytes When referring to hard disk drive capacity or communications volume MB stands for 1 000 000 bytes and GB stands for 1 000 000
62. ional devices This chapter provides basic instructions for installing optional hardware devices in the server These instructions are intended for users who are experienced with setting up Lenovo server hardware Installation guidelines Before you install optional devices read the following information Read the safety information that begins on page v and the guidelines in Handling static sensitive devices on page 13 This information will help you work safely When you install your new server take the opportunity to download and apply the most recent firmware updates This step will help to ensure that any known issues are addressed and that your server is ready to function at maximum levels of performance To download firmware updates for your server complete the following steps Note Changes are made periodically to the Lenovo Web site The actual procedure might vary slightly from what is described in this document 1 Go to http www lenovo com support 2 Enter your product number machine type and model number or select Servers from the Select your product list 3 Select Servers from the Brand list 4 From Family list select ThinkServer RS110 and click Continue 5 Click Downloads and drivers to download firmware updates Before you install optional hardware make sure that the server is working correctly Start the server and make sure that the operating system starts if an operating system is inst
63. keine elektromagnetischen St rungen zu erwarten sind Auszug aus dem EMVG Paragraph 3 Abs 4 Dieses Genehmigungsverfahren ist nach Paragraph 9 EMVG in Verbindung mit der entsprechenden Kostenverordnung Amtsblatt 14 93 kostenpflichtig Anmerkung Um die Einhaltung des EMVG sicherzustellen sind die Ger te wie in den Handb chern angegeben zu installieren und zu betreiben Japanese Voluntary Control Council for Interference VCCI statement TORE FRUERBEFER BER EHE AZ VCCI DEE CE 2472AA T amp SES H XE C CORE t KER TERN TB CBR MEENSRCFCEPHVET TORA CIRAD EITHER ET BEJERKENDLIEDHVUET Appendix B Notices 67 Taiwanese Class A warning statement SAME ef RAG Bae oe gt FE AE XE IP BH BF gt T he ik ASAT HE a OLE gt RA GERE RRR ub iu FAH RK Chinese Class A warning statement Fs B Jt 39 A RP sh HERR SE AT Ab iu G R D JA ESC RRIROLT REAR FR TT GOE Korean Class A warning statement o AAE APSLE AANAYSES 9 77 o9u ua ES ASAE NYE S454 uten ver UT Ba FE FUIRRE DFE 743827 Dar 7 aud 68 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Index A adapter installing 18 types supported 18 assistance getting 57 attention notices 2 baseboard management controller BMC functions 35 log 35 bays 4 beep codes 37 C caution statements 2 CD drive problems 45 CD eject button 28 CD DVD drive activity LED 28 problems 45 specification 4 Configuration Setup U
64. ling system to work properly Leave approximately 50 mm 2 0 in of open space around the front and rear of the server Do not place objects in front of the fans For proper cooling and airflow replace the server cover before you turn on the server Operating the server for extended periods of time more than 30 minutes with the server cover removed might damage server components You have followed the cabling instructions that come with optional adapters You have replaced a failed fan within 48 hours You have replaced a hot swap drive within 2 minutes of removal You do not operate the server without the air baffles installed Operating the server without the air baffles might cause the microprocessors to overheat Working inside the server with the power on Attention Static electricity that is released to internal server components when the server is powered on might cause the server to halt which could result in the loss of data To avoid this potential problem always use an electrostatic discharge wrist strap or other grounding system when you work inside the server with the power on You might be instructed to turn on the server while the cover is off to look at system board LEDs Follow these guidelines when you work inside a server that is turned on Avoid wearing loose fitting clothing on your forearms Button long sleeved shirts before you work inside the server do not wear cuff links while you are working inside the server
65. lowing components one at a time in the order shown restarting the server each time a Trained service technician only Microprocessor b Trained service technician only System board 00019701 Microprocessor x is not functioning or failed the built in self test Make sure that microprocessor x is installed correctly If the problem remains call for service 01298001 No update data for microprocessor 1 1 Update the BIOS code again see the Hardware Maintenance Manual on the ThinkServer Documentation DVD 2 Trained service technician only Reseat the microprocessor 3 Trained service technician only Replace the microprocessor 01298101 Bad update data for microprocessor 1 1 Update the BIOS code again see the Hardware Maintenance Manual on the ThinkServer Documentation DVD 2 Trained service technician only Reseat the microprocessor 3 Trained service technician only Replace the microprocessor 42 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Table 4 Abbreviated list of POST error codes continued Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step i
66. m media The operating system Make sure that the server supports the operating system If it does either no logical drive cannot be installed the is defined RAID servers or the EasyStartup program is not installed Run the option is not available EasyStartup program and make sure that setup is complete Software problems Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action You suspect a software 1 To determine whether the problem is caused by the software make sure that problem The server has the minimum memory that is needed to use the software For memory requirements see the information that comes with the software If you have just installed an adapter or memory the server might have a memory address conflict The software is designed to operate on the server Other software works on the server The software works on another server 2 If you received any error messages when using the software see the information that comes with the software for a description of the messages and suggested solution
67. me in the order shown restarting the server each time a Hot swap models Hard disk drive cable b Hard disk drive c Hard disk drive backplane or back plate d Trained service technician only System board 5962 Internal CD DVD drive configuration changed An expected CD or DVD drive was not detected 1 Run the Configuration Setup Utility program and load the default settings see Configuration Setup Utility program on page 34 2 Reseat the following components a DVD drive cable b DVD drive 3 Replace the following components one at a time in the order shown restarting the server each time a DVD drive cable b DVD drive c Trained service technician only System board Chapter 5 Solving problems 41 Table 4 Abbreviated list of POST error codes continued Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Error code Description Action 00012000 Processor machine check error 1 Trained service technician only Reseat the microprocessor 2 Replace the fol
68. n column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action Not all drives are recognized by the hard disk drive diagnostic test Remove the drive indicated on the diagnostic tests then run the hard disk drive diagnostic test again If the remaining drives are recognized replace the drive that you removed with a new one The server stops responding during the hard disk drive diagnostic test Remove the hard disk drive that was being tested when the server stopped responding and run the diagnostic test again If the hard disk drive diagnostic test runs successfully replace the drive that you removed with a new one A hard disk drive was not detected while the operating System was being started A hard disk drive passes the diagnostic test but the problem remains Reseat all hard disk drives and cables then run the hard disk drive diagnostic tests again See Solving undetermined problems in the Hardware Maintenance Manual 46 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Intermittent problems Follow the suggested actions in the order in wh
69. no pro itajte Sigurnosne Upute P ed instalac tohoto produktu si p e t te p ru ku bezpe nostn ch instrukc L s sikkerhedsforskrifterne for du installerer dette produkt Lees voordat u dit product installeert eerst de veiligheidsvoorschriften Ennen kuin asennat t m n tuotteen lue turvaohjeet kohdasta Safety Information Avant d installer ce produit lisez les consignes de s curit Vor der Installation dieses Produkts die Sicherheitshinweise lesen Mpv ykaraotrjoete ro TIPOI V aut LABAOTE TIG M NPOPOPIEG aop Aeiaq safety information mmean mami ns 183p AT 1810 PINNU 397 A term k telep t se el tt olvassa el a Biztons gi el r sokat Prima di installare questo prodotto leggere le Informazioni sulla Sicurezza HRMOMBORMI HERRE BRA HEN HSS So AH ta ASS ACMA IIpez na ce uHcTas mpa OBO IIPoAyKT rrpouurajre uHubopManmjara 3a 6es6e mocr Les sikkerhetsinformasjonen Safety Information for du installerer dette produktet Przed zainstalowaniem tego produktu nale y zapozna sie z ksi k Informacje dotycz ce bezpiecze stwa Safety Information Antes de instalar este produto leia as Informa es sobre Seguran a llepen ycTaHoBKO nponykra NPOYTUTE UHCTPYKLIUM no TEXHUKE 6ezonacHocTn Pred in tal ciou tohto zariadenia si pe taje Bezpe nostn predpisy Pred namestitvijo tega proizvoda preberite Varnostne informacije Lenovo 2008 Portions IBM Corp 200
70. o start the EasyStartup DVD do the following 1 Insert the EasyStartup DVD and restart the server If the EasyStartup program 2 Follow the instructions on the screen and continue to the main interface 3 When you arrive at the Home screen do any of the following Click Compatibility notes to view detailed information about the operating systems and server configurations supported by that version of the EasyStartup program Click User Guide to view an overview of the various functions provided by that version of the EasyStartup program Click Hardware list to view a list of hardware detected by the ThinkServer EasyStartup program Click Install operating system to begin the process of creating a response file and installing the operating system As part of this procedure you will be given the opportunity to include the ThinkServer EasyUpdate program and the ThinkServer EasyManage products ThinkServer EasyManage Core Server or ThinkVantage EasyManage Remote Client as part of the installation process You also can provide one or more command line based instructions to be run at the end of the operating system installation process Click About to view version information and legal notices To use the EasyStartup DVD to install an operation system using a preexisting response file do the following 1 Insert the EasyStartup DVD and restart the server If the EasyStartup program 2 Follow the instructions on the screen until you get
71. oblems Appendix A Getting help and technical assistance Before you call p Se M euet Using the documentation Getting help and information from the World Wide Web Calling for service Sik cer rubo ute veh ie ee Using other services e Purchasing additional services Lenovo product service Appendix B Notices Trademarks Important notes Waste electrical and electronic equipment WEEE notices Battery return program German Ordinance for Work gloss statement Electronic emissions notices ox we deo Federal Communications Commission FCC statement Industry Canada Class A emission compliance statement Avis de conformit la r glementation d Industrie Canada Australia and New Zealand Class A statement United Kingdom telecommunications safety requirement European Union EMC Directive conformance statement German Class A compliance statement Japanese Voluntary Control Council for Interference VCCI statement Taiwanese Class A warning statement Chinese Class A warning statement Korean Class A warning statement Index iV ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Safety Before installing this product read the Safety Information Ag aD del Gang iial Ida us 5 J Antes de instalar este produto leia as Informac es de Seguranga ERAT in ZA wi Safety Information GEHE S KEKE DAT SAHNE RATA gt Prije instalacije ovog produkta obavez
72. ocument are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons The information contained in this document does not affect or change Lenovo product specifications or warranties Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties All information contained in this document was obtained in specific environments and is presented as an illustration The result obtained in other operating environments may vary Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you Any references in this publication to non Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites The materials at those Web sites are not part of the materials for this Lenovo product and use of those Web sites is at your own risk Any performance data contained herein was determined in a controlled environment Therefore the result obtained in other operating environments may vary significantly Some measurements may have been made on development level systems and there is no guarantee that these measurements will be the same on generally available systems Furthermore some measurements may have been Lenovo 2008 Portions IBM Corp 2008 61 Trademarks est
73. ogram also provides compatibility notes to help you determine what server configurations and operating systems are supported by that specific version of the program The ThinkServer EasyStartup program also enables you to save the response file on a USB device or diskette for reuse and an option that enables you to install an operating systems using the saved response This option is useful if you intend to install the same operating system on similarly configured ThinkServer servers Notes 1 If you intend to implement a RAID make sure your storage controller or RAID adapter is configured correctly before you use the ThinkServer EasyStartup program to install the operating system 2 f you are using any external storage devices or fiber channels use the utilities provided with the device You also will have to provide the device drivers for these devices and install them after the EasyStartup program finishes installing the operating system 3 The EasyStartup DVD requires that you have a DVD drive that is configured as your first device in the startup sequence Use the Configuration Setup Utility program to view or change your startup sequence See Using the Configuration Setup Utility program on page 34 4 To install an operating system you need the operating system installation disc CD or DVD and the associated product key if one was provided 32 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide T
74. on page 14 All banks of memory are enabled The server might have automatically disabled a memory bank when it detected a problem Check the system event error log for error message 289 see Using the Configuration Setup Utility program on page 34 if a DIMM was disabled by a systems management interrupt SMI replace the DIMM Run memory diagnostics see Running the diagnostic programs in the Hardware Maintenance Manual Add one pair of DIMMs at a time making sure that the DIMMs in each pair match Reseat the DIMMs Replace the following components one at a time in the order shown restarting the server each time a DIMMs b Trained service technician only System board Microprocessor problems Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action The server emits a continuous beep during POST indicating that the microprocessor is not working correctly T Correct any errors that are indicated by the LEDs see System board LEDs in the Hardware Maintenance Manual Make sur
75. or additional information about Lenovo and Lenovo products what to do if you experience a problem with your system and whom to call for service if it is necessary Before you call Before you call make sure that you have taken these steps to try to solve the problem yourself Check all cables to make sure that they are connected Check the power switches to make sure that the system and any optional devices are turned on Use the troubleshooting information in your system documentation and use the diagnostic tools that come with your system Information about diagnostic tools is in the Hardware Maintenance Manual on the ThinkServer Documentation DVD that comes with your system e Go to the Lenovo support Web site at http www lenovo com support to check for technical information hints tips and new device drivers or to submit a request for information You can solve many problems without outside assistance by using the information available on the Lenovo support site or by following the troubleshooting procedures that Lenovo provides in the documentation that is provided with your Lenovo product The documentation that comes with Lenovo systems also describes the diagnostic tests that you can perform Most systems operating systems and programs come with documentation that contains troubleshooting procedures and explanations of error messages and error codes If you suspect a software problem see the documentation for t
76. ordance with the European Directive 2006 66 EC batteries and accumulators are labeled to indicate that they are to be collected separately and recycled at end of life The label on the battery may also include a chemical symbol for the metal 64 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide concerned in the battery Pb for lead Hg for mercury and Cd for cadmium Users of batteries and accumulators must not dispose of batteries and accumulators as unsorted municipal waste but use the collection framework available to customers for the return recycling and treatment of batteries and accumulators Customer participation is important to minimize any potential effects of batteries and accumulators on the environment and human health due to the potential presence of hazardous substances For proper collection and treatment go to http www lenovo com lenovo environment For California Perchlorate material special handling may apply See http www dtsc ca gov hazardouswaste perchlorate The foregoing notice is provided in accordance with California Code of Regulations Title 22 Division 4 5 Chapter 33 Best Management Practices for Perchlorate Materials This product part may include a lithium manganese dioxide battery which contains a perchlorate substance German Ordinance for Work gloss statement The product is not suitable for use with visual display work place devices according to clause 2 of the German
77. product recycling offerings can be found on Lenovo s Internet site at http www lenovo com lenovo environment Esta unidad debe reciclarse o desecharse de acuerdo con lo establecido en la normativa nacional o local aplicable Lenovo recomienda a los propietarios de equipos de tecnologia de la informacion TI que reciclen responsablemente sus equipos cuando stos ya no les sean tiles Lenovo dispone de una serie de programas y servicios de devoluci n de productos a fin de ayudar a los propietarios de equipos a reciclar sus productos de TI Se puede encontrar informaci n sobre las ofertas de reciclado de productos de Lenovo en el sitio web de Lenovo hitp www lenovo com lenovo environment Notice This mark applies only to countries within the European Union EU and Norway This appliance is labeled in accordance with European Directive 2002 96 EC concerning waste electrical and electronic equipment WEEE The Directive determines the framework for the return and recycling of used appliances as applicable throughout the European Union This label is applied to various products to indicate that the product is not to be thrown away but rather reclaimed upon end of life per this Directive ER IOI It ELBEBLU NATI IBEINTDABMENET I D RS IE EU ra ENST o BER T PER IR 2002 96 EC WEEE OF SV M 5 Yv C WET COMPS EU RENZ HHT 5 EN 2 Aka D BIN EU FI IN DEF EREDT EP IOF NIUE EHEAR o RRCA o CHIE RMT OVER HDI EE Af 5 XE 5 7 5 f amp OM
78. pter H Riser card assembly Adapter support bracket Dm Expansion slot 2 Chapter 2 Installing optional devices 19 To install an adapter complete the following steps 1 Read the safety information that begins on page M and Installation guidelines on page 11 2 Turn off the server and peripheral devices and disconnect the power cord and all external cables Remove the cover 3 If you have installed an optional PCI X riser card assembly disconnect the riser card power cable f from the riser card assembly 4 Grasp the riser card at the front and rear edges and lift to remove the riser card assembly El Place the riser card assembly on a flat static protective surface 5 Remove the expansion slot cover on the slot that you intend to use Attention PCI expansion slot covers must be installed on all vacant slots This maintains the electronic emissions characteristics of the server and ensures proper cooling of server components 6 Follow the instructions that come with the adapter to set any jumpers or switches 20 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Ne 10 11 Attention When you install an adapter make sure that it is completely and correctly seated in the expansion slot in the riser card Incomplete insertion might cause damage to the riser card system board or the adapter when you turn on the server Carefully grasp the adapter by its top edge or upper corners
79. que address in the Configuration Setup Utility system is less than the number program and none of the serial ports is disabled of installed serial ports The serial port adapter if one is installed is seated correctly 2 Reseat the serial port adapter 3 Replace the serial port adapter A serial device does not work 4 Make sure that The device is compatible with the server The serial port is enabled and is assigned a unique address Bay device is connected to the correct connector see 2 Reseat the following components a Failing serial device b Serial cable 3 Replace the following components one at a time in the order shown restarting the server each time a Failing serial device b Serial cable c Trained service technician only System board EasyStartup problems Table 5 EasyStartup DVD Follow the suggested actions in the order in which they are listed in the Action Column until the problem is resolved See the Hardware Maintenance Manual on the Documentation DVD to determine which components are customer replaceable units CRU s and which fields are field replacable units FRU s If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action The EasyStartup DVD will not start bootable CD or DVD drive Make sure that the server supports the EasyStartup program and has a s
80. r country or region is not provided contact your Lenovo reseller or Lenovo marketing representative If possible be at your computer when you call Have the following information available Machine type and model Serial numbers of our hardware products Description of the problem Exact working of any error messages Hardware and software configuration information 58 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Using other services If you travel with a Lenovo notebook computer or relocate your computer to a country where your desktop notebook or server machine type is sold your computer might be eligible for International Warranty Service which automatically entitles you to obtain warranty service throughout the warranty period Service will be performed by service providers authorized to perform warranty service Service methods and procedures vary by country and some services might not be available in all countries International Warranty Service is delivered through the method of service Such as depot carry in or on site service that is provided in the servicing country Service centers in certain countries might not be able to service all models of a particular machine type In some countries fees and restrictions might apply at the time of service To determine whether your computer is eligible for International Warranty Service and to view a list of the countries where service is ava
81. rains static electricity from the package and from your body Remove the device from its package and install it directly into the server without setting down the device If it is necessary to set down the device put it back into its static protective package Do not place the device on the server cover or ona metal surface Take additional care when you handle devices during cold weather Heating reduces indoor humidity and increases static electricity Removing the cover To remove the cover complete the following steps 1 Read the safety information that begins on page v and Installation guidelines 2 Turn off the server and all attached devices 3 Disconnect all external cables and power cords Chapter 2 Installing optional devices 13 4 Press the cover release button fj 5 Slide the cover back approximately 1 27 cm 0 5 inches then lift it off the server Attention For proper cooling and airflow replace the cover before you turn on the server Operating the server for extended periods of time more than 30 minutes with the cover removed might damage server components Installing a memory module The following notes describe the types of dual inline memory modules DIMMs that the server supports and other information that you must consider when installing DIMMs The server supports 512 MB 1 GB and 2 GB DIMMs for a maximum of 8 GB of system memory See http www lenovo com accessories for a li
82. replaced If the green hard disk drive activity LED is flashing the drive is being accessed If you have other devices to install do so now Otherwise go to Completing the installation on page 24 Installing an adapter The following notes describe the types of adapters that the server supports and other information that you must consider when you install an adapter Locate the documentation that comes with the adapter and follow those instructions in addition to the instructions in this section If you have to change switch settings or jumper settings on the adapter follow the instructions that come with the adapter The adapter slots are on the riser card assembly You must first remove the riser card assembly to access the adapter slots The two PCI Express slots on the riser card assembly support PCI Express x8 1 0a adapters You can install one full height three quarter length adapter in expansion slot 1 and one low profile half length adapter in expansion slot 2 Note When the optional Remote Supervisor Adapter II SlimLine is installed in the server you can install only a half length adapter in expansion slot 1 If you have installed an optional PCI X riser card assembly in the server you can install a full height three quarter length PCI X 64 133 MHz adapter in the PCI X slot on the riser card assembly Note When the optional Remote Supervisor Adapter II SlimLine is installed in the server you can install only a
83. s preceded by Trained service technician only that step must be performed only by a trained service technician Error code Description Action 19990301 Hard disk drive boot sector error 1 Reseat the following components depending on the server model Hot swap models a Hard disk drive b SAS SATA controller Simple swap models a Hard disk drive b Hard disk drive cable Replace the following components one at a time depending on the server model in the order shown restarting the server each time Hot swap models a Hard disk drive b Hard disk drive backplane c SAS SATA controller Trained service technician only System board Simple swap models a Hard disk drive b Hard disk drive cable c Trained service technician only System board Chapter 5 Solving problems 43 Table 4 Abbreviated list of POST error codes continued Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Error code Description Action 19990305 An operating system was not 1 Make sure that a
84. s to the problem 3 Contact your place of purchase of the software Chapter 5 Solving problems 55 Universal Serial Bus USB device problems Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action A USB device does not work 1 Make sure that The correct USB device driver is installed The operating system supports USB devices 2 Make sure that the USB configuration options are set correctly in the Configuration Setup Utility program menu see the User s Guide for more information 3 If you are using a USB hub disconnect the USB device from the hub and connect it directly to the server Video problems See Monitor problems on page 50 56 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Appendix A Getting help and technical assistance If you need help service or technical assistance or just want more information about Lenovo products you will find a wide variety of sources available from Lenovo assist you This section contains information about where to go f
85. st of memory modules that you can use with the server The amount of usable memory will be reduced depending on the system configuration A certain amount of memory must be reserved for system resources Use the system summary in the Configuration Setup Utility program to view the total amount of installed memory and the amount of configured memory see Using the Configuration Setup Utility program on page 34 The server comes with one 512 MB or 1 GB DIMM installed in DIMM connector 1 and an identical DIMM the same size speed type and technology installed in DIMM connector 3 If you install a pair of DIMMs in DIMM connectors 2 and 4 the size speed type and technology of the DIMMs that you install in DIMM connectors 2 and 4 must match each other However they do not have to be the same size speed type and technology as the DIMMs that are installed in DIMM connectors 1 and 3 You can use compatible DIMMs from various manufacturers in the same pair Install only double data rate II DDR Il PC2 5300 unbuffered synchronous dynamic random access memory SDRAM with error correcting code ECC DIMMs These DIMMs must be compatible with the latest PC2 5300 SDRAM unbuffered DIMM specification If you install a pair of 2 GB DIMMs and a pair of other size DIMMs the 2 GB DIMMs must be installed as the first pair in DIMM connectors 1 and 3 When you restart the server after you add or remove a DIMM a message is displayed indicating
86. swap Serial ATA hard disk drive 16 size 4 slot locations PCI Express 9 slots 4 software problems 55 solving problems 37 70 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide specifications 3 Standby mode 29 statements and notices 2 support web site 57 system board connectors 28 system board connectors 9 system error LED 27 systems management connector 29 T temperature 4 trademarks 62 troubleshooting chart 45 turning off the server 29 turning on the server 29 T V gloss statement 65 U Universal Serial Bus USB problems 56 USB connector 28 utility program BMC 35 Configuration Setup 34 LSI Logic Configuration Utility program 34 V video connector 28 video controller 4 W web site publication ordering 57 support 57 Web site Lenovo support 1 11 35 38 weight 4 Index 71 72 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide lenovo Part Number 46U0855 Printed in USA 1P P N 46U0855
87. system board with Wake on LAN support Serial port Four USB ports two on front and two on rear of server Systems management port if an optional Remote Supervisor Adapter II SlimLine is installed Hard disk controllers Serial ATA SATA controller simple swap SATA models Serial attached SCSI SAS controller with integrated RAID hot swap SAS SATA models that supports RAID levels 0 1 1E Environment Air temperature Server on 10 to 35 C 50 0 to 95 0 F altitude O to 914 4 m 3000 ft Server on 10 to 32 C 50 0 to 89 6 F altitude 914 4 m 3000 ft to 2133 6 m 7000 ft Server off 10 to 43 C 50 0 to 109 4 F maximum altitude 2133 6 m 7000 ft Shipping 40 to 60 C 40 to 140 F maximum altitude 2133 6 m 7000 ft Humidity Server on 8 to 80 Server off 8 to 80 Acoustical noise emissions Sound power idling 6 5 bel maximum Sound power operating 6 5 bel maximum Heat output Approximate heat output in British thermal units Btu per hour Minimum configuration 341 Btu per hour 100 watts Maximum configuration 1024 Btu per hour 300 watts Electrical input Sine wave input 50 60 Hz required Input voltage low range Minimum 100 V ac Maximum 127 V ac Input voltage high range Minimum 200 V ac Maximum 240 V ac Approximate input kilovolt amperes KVA Minimum 0 102 kVA
88. t swap hard disk drive model 3 5 inch drives SATA simple swap hard disk drive model 3 5 inch drives and a SAS hot swap model with 2 5 inch hard disk drives are also available This illustration might differ slightly from your hardware For a list of supported optional devices for the server see http www lenovo com See the Rack Installation Instructions document for complete rack installation and removal instructions The Lenovo ThinkServer Documentation DVD The Lenovo ThinkServer Documentation DVD contains documentation for the server in Portable Document Format PDF Hardware and software requirements The Lenovo ThinkServer Documentation DVD requires the following minimum hardware and software Microsoft Windows XP Windows 2000 or Red Hat Linux 100 MHz microprocessor e 32 MB of RAM Adobe Acrobat Reader 3 0 or later or xpdf which comes with Linux operating systems Notices and statements in this document The caution and danger statements in this document are also in the multilingual Safety Information document which is on the Lenovo ThinkServer Documentation DVD Each statement is numbered for reference to the corresponding statement in the Safety Information document The following notices and statements are used in this document Note These notices provide important tips guidance or advice Important These notices provide information or advice that might help you avoid inconvenient or pro
89. tartable If the startup boot sequence settings have been changed make sure that the CD or DVD drive is first in the startup sequence If more than one CD or DVD drive is installed make sure that only one drive is set as the primary drive Start the CD from the primary drive The ServeRAID Manager program cannot view all installed drives or the operating system cannot be installed Make sure that the hard disk drive is connected correctly Make sure that the SAS hard disk drive cables are securely connected 54 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Table 5 EasyStartup DVD continued Follow the suggested actions in the order in which they are listed in the Action Column until the problem is resolved See the Hardware Maintenance Manual on the Documentation DVD to determine which components are customer replaceable units CRU s and which fields are field replacable units FRU s If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action The operating system Make more space available on the hard disk installation program continuously loops The EasyStartup Make sure that the operating system media is supported by the EasyStartup program program will not start the See the EasyStartup DVD label for a list of supported operating system versions operating syste
90. te drive read write errors make sure that the distance between the monitor and any external diskette drive is at least 76 mm 3 in b Non Lenovo monitor cables might cause unpredictable problems 2 Reseat the following components Monitor cable Remote Supervisor Adapter II SlimLine if one is installed 3 Replace the following components one at a time in the order shown restarting the server each time a Monitor cable b Monitor c Remote Supervisor Adapter II SlimLine if one is installed d Trained service technician only System board Wrong characters appear on the f the wrong language is displayed update the BIOS code with the correct screen language 2 Reseat the monitor cable 3 Replace the following components one at a time in the order shown restarting the server each time a Monitor b Trained service technician only System board Chapter 5 Solving problems 51 Optional device problems Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action An optional device that was just
91. tem information and identify the server You can also save one or more commands as a text file and run the file as a script Configuring the Gigabit Ethernet controllers The Ethernet controllers are integrated on the system board They provide an interface for connecting to a 10 Mbps 100 Mbps or 1 Gbps network and provide full duplex FDX capability which enables simultaneous transmission and reception of data on the network If the Ethernet ports in the server support auto negotiation the controllers detect the data transfer rate 10BASE T 100BASE TX or 1000BASE T and duplex mode full duplex or half duplex of the network and automatically operate at that rate and mode Note The Ethernet controller for Ethernet connector 1 supports Serial over LAN SOL You do not have to set any jumpers or configure the controllers However you must install a device driver to enable the operating system to address the controllers For device drivers and information about configuring the Ethernet controllers see the Broadcom NetXtreme II Gigabit Ethernet Software CD that comes with the server To find updated information about configuring the controllers complete the following steps Note Changes are made periodically to the Lenovo Web site The actual procedure might vary slightly from what is described in this document 1 Go to http www lenovo com support 2 Enter your product number machine type and model number or select Servers
92. the server can be turned off from the Remote Supervisor Adapter II SlimLine user interface The integrated systems management processor mini BMC can turn off the server as an automatic response to a critical system failure You can turn off the server through a request from the service processor 30 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Chapter 4 Configuring the server Lenovo provides a number of programs to assist you with getting your server up and running quickly ThinkServer EasyStartup program This program simplifies the process of installing the operating system and devices drivers It is on the ThinkServer EasyStartup DVD provided with your server For details see Using the ThinkServer EasyStartup program on page Configuration Setup Utility program This program enables you to configure hardware settings and preferences in the BIOS For details see Using the Configuration Setup Utility program on page RAID configuration programs Adaptec RAID HOSTRaid Configuration Utility program This program is part of the BIOS code on models that have an integrated ServeRAID 8e Adaptec HostRAID controller LSI Configuration Utility This program is part of the BIOS code on models with an optional LSI storage controller with RAID capability Broadcom Gigabit Ethernet Utility program Use this program to configure the network as a startable bootable device or specify where the net
93. the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action The CD or DVD drive tray is not working Make sure that the server is turned on 2 Insert the end of a straightened paper clip into the manual tray release opening 3 Reseat the CD or DVD drive 4 Replace the CD or DVD drive General problems Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Symptom Action A cover lock is broken an LED is not working or a similar problem has occurred If the part is a CRU replace it If the part is a FRU the part must be replaced by a trained service technician Hard disk drive problems Follow the suggested actions in the order in which they are listed in the Actio
94. tility program 34 configuring hot swap SAS or SATA devices 34 SAS SATA controller 34 the server 32 configuring hardware 31 connectors 28 front 25 optional devices 9 rear 26 controller Ethernet configuring 26 35 type 4 hard disk drive 4 SAS 4 SATA 4 video 4 cover installing 25 removing 13 D danger statements 2 DIMMs connector locations 15 supported 4 display problems 50 documentation CD 2 drives 4 DVD drive problems 45 Lenovo 2008 Portions IBM Corp 2008 E electrical input 4 environment 4 error messages POST 38 error symptoms CD ROM drive DVD ROM drive 45 general 46 hard disk drive 46 intermittent 47 keyboard USB 47 memory 49 microprocessor 49 monitor 50 mouse USB 47 optional devices 52 pointing device USB 47 power 53 serial port 54 software 55 USB port 56 Ethernet activity LED 28 connector 28 controller 4 configuring 26 link LED 28 expansion bays 4 expansion slots 4 F features 3 filler panel 12 firmware updates 1 G getting help 57 gloss statement Germany 65 H hard disk drive activity LED 27 hot swap SATA 17 installing 16 problems 46 removing 17 SAS 16 17 SCSI See SAS SerialATA 16 heat output 4 help getting 57 humidity 4 69 important notices 2 installation order memory modules 14 installing adapters 18 cover 25 DIMMs 14 hard disk drives 15 integrated controllers 4 functions 4 intermittent problems 47 L LED cd drive a
95. tional information that is not included in the server documentation To check for updates complete the following steps Note Changes are made periodically to the Lenovo Support Web site The actual procedure might vary slightly from what is described in this document 1 Go to http www lenovo com support 2 Enter your product number machine type and model number or select Servers from the Select your product list 3 Select Servers from the Brand list 4 From Family list select ThinkServer RS110 and click Continue The server comes with an EasyStartup DVD to help you configure the hardware install device drivers and install the operating system The server comes with a limited warranty You can obtain up to date information about the server and other Lenovor products at http www lenovo com thinkserver Record information about the server in the following table You will need this information when you register the server with Lenovo Product name ThinkServer RS110 Machine type ThinkServer RS110 Types 6435 6436 6437 and 6438 Model number Serial number Key serial number Key manufacturer Key phone number The model number and serial number are on the ID label on the bezel as shown in the following illustration Lenovo 2008 Portions IBM Corp 2008 1 Note This illustration shows a serial attached SCSI SAS hot swap hard disk drive model 3 5 inch drives A Serial ATA SATA ho
96. tions for RAID arrays continued Server configuration RAID array configuration before operating system is installed RAID array management after operating system is installed ServeRAID MR10i adapter installed 2 5 inch drive models only WebBIOS Configuration Utility Ctrl H during server startup BIOS Configuration Setup Utility WebBIOS Configuration Utility Ctrl H during server startup MegaCLI command line interface program Ctrl A during server startup ServerGuide For more information about these programs see Configuring the server in the User Guide on the ThinkServer Documentation DVD Using the ThinkServer EasyStartup program The ThinkServer EasyStartup program simplifies the process of installing the operating system and devices drivers by performing the following tasks Detects installed hardware devices Guides you through the process of creating a response file Prepares the hard disk for installation Prompts you to insert the operating system installation disc Initiates an unattended installation of the operating system and device drivers for most adapters and devices The program is contained on the ThinkServer EasyUpdate disc provided with your server If you did not receive an EasyStartup DVD with your server you can download an ISO image of the DVD from The program has a built in help system and User Guide to answer any questions you might have The pr
97. to the Start option screen 3 When the Start option screen is displayed do the following a Insert the USB device or diskette that contains the response file b Select Install the operating system using a preexisting response file c Click OK 4 Follow the remaining instructions on the screen to complete the procedure Using ThinkServer EasyManage products ThinkServer EasyManage Core Server provides centralized hardware and software inventory management and secure automated system management through a single console The ThinkServer EasyManage Agent enables other computers and servers to be managed by the centralized console You can install the ThinkServer EasyManage Core Server program from the ThinkServer EasyManage CD or you can download and install the program from After one instance of the ThinkServer EasyManage Core Server has been installed you can use the ThinkServer EasyManage Agent installer to install the agent on other servers and clients on the network Also the EasyServer EasyStartup program provides an option to install these products as part of the operating system installation process Chapter 4 Configuring the server 33 Using the Configuration Setup Utility program The Configuration Setup Utility program is part of the BIOS You can use it to perform the following tasks View configuration information View and change assignments for devices and I O ports Set the date and time Set and change passwords
98. umn until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units CRU and which components are field replaceable units FRU If an action step is preceded by Trained service technician only that step must be performed only by a trained service technician Error code Description Action 062 Three consecutive boot failures 1 Update the system firmware to the latest level see the Hardware Maintenance Manual on the ThinkServer Documentation DVD using the default configuration 2 Trained service technician only Replace the system board 101 Tick timer internal interrupt failure Trained service technician only Replace the system board 102 Internal timer channel 2 test Trained service technician only failure Replace the system board 151 Real time clock error Reseat the battery 2 Replace the following components one at a time in the order shown restarting the server each time a Battery b Trained service technician only System board 38 ThinkServer RS110 Types 6435 6436 6437 and 6438 Installation Guide Table 4 Abbreviated list of POST error codes continued Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved See the parts listing in the Hardware Maintenance Manual to determine which components are
99. work startup option is displayed in the startup sequence For additional information see Enabling the Broadcom Gigabit Ethernet Utility program on pagg Configuring the Gigabit Ethernet controllers on page 35 Baseboard management controller SMBridge management utility program Use these programs to configure the baseboard management controller download firmware updates download SDR FRU updates and remotely manage a network ThinkServer EasyManage products ThinkServer EasyManage Core Server and ThinkServer EasyManage Remote Client work together to provide centralized hardware and software inventory management and secure automated system management through a single console See Using ThinkServer EasyManage products on page 33 The following table lists the different server configurations and the applications that are available for configuring and managing RAID arrays Table 3 Configuration and management applications for RAID arrays Server configuration RAID array configuration before operating system is installed RAID array management after operating system is installed Integrated SATA and no SAS controller card installed None None SAS SATA controller card LSI 1064 installed LSI Logic Configuration Utility Ctrl C during server startup ServerGuide MegaRAID Storage Manager Lenovo 2008 Portions IBM Corp 2008 31 Table 3 Configuration and management applica

Download Pdf Manuals

Related Search

Related Contents

dreamGEAR 17 In 1 Bundle Pak for DS Lite  Paradyne Phone Filter 6035 User's Manual  DVR User Manual - SPYMICRO CCTV & Surveillance Technologies  LASER VET 1000  - Rüegg  "user manual"  RHONA M-344 - Pinturas Isaval  User`s Manual  DS 9DVF3 • DS 12DVF3 DS 14DVF3 • DS 18DVF3  DSC 9047 Quick Reference Guide  

Copyright © All rights reserved. Failed to retrieve file