Lanzar Car Audio OPTIDRIVE OPTIMC90 User's Manual
Contents
1. Lanz ar OP TIo SUVE 1600 6Sred Brooklyn N 1TIZOZ 2 si 0X0 0 220 Ole USER S MANUAL anzar OP Tht Ve OPTIMC90 700 WATT MOTORCYCLE ATV SNOWMOBILE MOUNT 4 CHANNEL AMPLIFIER W DUAL HANDLEBAR MOUNT ALUMINUM DIECAST WEATHERPROOF SPEAKERS W MP3 IPOD INPUT amp USB CHARGER WWW LANZAR COM Installation Instructions Congratulations on your purchase of this Lanzar OP TIDRIVE Series premier amplified speaker system Like all Lanzar products this motorcycle system has been thoroughly tested to ensure consistent reliable performance under some rigorous conditions Our systems were designed to with stand water moisture heat and direct sun exposure We pride ourselves in customer satisfaction If you should have any questions regarding the installation and or operation of your Lanzar OPTIDRIVE Series motorcycle speaker system which is not covered in this manual please contact your Lanzar Dealer or lanzar Technical Support What is Included Upon un packing your new Lanzar OPTIDRFIVE Series audio system please check to ensure you have all the included parts Step 1 Install shaped clamp Item 2 Z shaped clamp Item 3 threaded on to the bottom of each speaker enclosure Item 1 Use the provided bolts item 14 Step 2 Bolt each speaker with its mount to the handlebar of the vehicle Hardware included will allow for mounting on to 1 diameter and smaller h2. Aluminum with shinny chromed Speaker housing Dimensions 3 25 W x 3 25 H x4 375 L E Micro amplifier with harness amp universal mount included Amp dimension 3 5 W x1 375 H x3 L E USB charge included Dimensions 2 5 W x1 75 H x 1 5 L E Radio MP3 Mount Dimensions 3 5 L x 0 625 W x 3 125 H e 1 Universal 12 Volt Wire Harness Connection
3. with Image 9 9 with Image 1 Pair of 350 Watt Stereo Chrome 1 12 Volt Direct Plug for Compatible Speaker Enclosures with Speaker Wires Motorcycles 1 Pair of Handlebar Speaker 1 Enclosure Shape Clamp 1 USB Charger Power Source 1 Pair of Handlebar Music Source 2 1 Adjustable Rotary Volume Mount Z Shape Clamp 2 Control 3 5 mm Interface O This wire should be connected 12 Volt power source Sains D 5 a Step 7 pai to neck area of motorcycle and plug into harness Use Item 13 wire ties to sav Step 8 Bolt amplifier on Motorcycle with provided Bolt item 15 Best if mounted directly to 1 Universal chrome Handlebar Mp3 Audio D i frame out of reach from direct heat or crash bar Mount with 6 Black Wire Tie Lockable Straps Step 9 Attach Velcro strips Item 12 one side to our Universal Bracket Item 5 the other 2 Black Industrial Velcro Pitt to your MP3 player audio source Step 10 Connect 3 5mm male connection into Audio device and opposite side into Micro Amplifier 1 Amplifier 12 Volt Ground Blue Spade Terminal 2 Screws for Speaker Specifications 9 T E 3 motorcycle speaker E Frequency Response 220Hz 21KHZ 1 Amplifier 12 Volt Blue Male T 1 Screw Washer and Nut for Amplifier d voice coil 4 ohm Impedance E SPL 85 dB 1W 1M E
4. andlebars Project each speaker at desired listening level for best performance Step 3 Secure speaker wires either through handlebars for a custom look or use Item 13 wire ties to secure to the handlebars Step 4 Bolt the rotary volume control Item 11 to the handlebars using the vehicle provided hardware Then run 3 5 mm connection down to desired amplifier location Use Item 13 wire ties to secure to the handlebars Have 3 5 mm male connection close to mount The Connector that comes pre installed on the amplifier wire harness Item 8 was designed to allow for direct plug in for most American Motorcycles Item 9 If mounting on a metric or universal vehicle this harness will not be used and replaced with the terminals connectors provided in the enclosed parts bag according to the installation instructions Items 6 7 amp 8 Follow wire instructions as shown in Diagram A Be sure to match the proper polarity for all connections The polarity for the speaker terminals solid color wire wire with stripe Blue wire 12 Volt Positive terminal trigger wire Black wire 12 Volt Ground to chassis of vehicle Step 5 Bolt the Universal Handlebar MP3 Audio Mount Item 5 using provided black industrial velcro adhesive strips Item 12 Remove bolt from existing switch housing on motorcycle and secure to bracket Step 6 Bolt the USB Charger Power Source Item 10 using vehicle provided hardware Part Part
Download Pdf Manuals
Related Search