Lantronix Switch EDS1100 User's Manual
Contents
1. Firmware Version Build Date Serial Number Uptime Permanent Config Network Settings Interface Link MAC Address Host IP Address Default Gateway Domain Primary DNS Secondary DNS Line Settings Line 1 Line 2 Tunneling Tunnel 1 Tunnel 2 Lantronix EDS2100 9 9 9 9T9 Oct 27 2009 11 16 13 22 0 days 02 28 38 Saved eth0 10 Mbps Full 10 Mbps Full 00 20 4a 9d 00 80 lt None gt 172 19 205 52 255 255 0 0 lt None gt lt None gt lt None gt lt None gt RS232 9600 None 8 1 None RS232 9600 None 8 1 None Connect Accept Mode Mode Disabled Waiting Disabled Waiting CONFIGURATION USING WEB MANAGER CONTINUED LANTRONIX EVOLUTION OS Copyright Lantronix Inc 2007 2009 All rights reserved 2 Use the menu to navigate to sub pages and configure the EDS WWW LANTRONIX COM 11 1 14 10 9 15 45 AM EDS2100 Power blue TX Serial 1 green RX Serial 1 yellow TX Serial 2 green RX Serial 2 yellow Diagnostic EDS1100 Power blue TX Serial green RX Serial yellow Diagnostic 09276LTX_QSG_1100_ 2100 7 indd 15 16 D Quick Start Guide EDS1100 2100 LEDS MEANING ON EDS is receiving power Blinking EDS is transmitting data on serial port 1 Blinking EDS is receiving data on serial port 1 Blinking EDS is transmitting data on serial port 2 Blinking EDS is receiving data on serial port 2 ON EDS firmware has c2. USING THE DEVICEINSTALLER UTILITY CONTINUED Note f the unit already has an IP address e g DHCP has assigned an IP address click the Search x icon and select the unit from the list of Lantronix device servers on the local network 2 Click the Assign IP icon e Assign IP 7 3 If prompted enter the hardware address on the product label and click Next Device Identification Enter the hardware address of the device This is typically printed on the back panel of the device in the Form 12 34 56 78 94 BC O0 20 44 41 135 D9 4 Select Assign a specific IP address and click Next 5 Enter the IP address The Subnet mask displays automatically based on the IP address if desired you may change it On a local network you can leave the Default gateway blank all zeros Click Next 09276LTX_QSG_1100 2100 7 indd 9 10 USING THE DEVICEINSTALLER UTILITY CONTINUED IP Settings Please Fill in the IP address subnet and gateway to assign the device The subnet will be Filled in automatically as you type but please verify it For accuracy Incorrect values in any of the below Fields can make it impossible For your device to communicate and can cause network disruption IP address 172 19 205 52 eno 2 0 0 Subnet mask Default gateway 0 0 0 0 6 Click the Assign button and wait several seconds until a confirmation message displays Click Finish 7 Click the Close button to close the dial
3. D 00 80 39 9 9 9 9T9 Online 172 19 205 52 Statically 255 255 0 0 0 0 0 0 2 True True True 23 True 80 True Step 4 Complete the Configuration Once the unit is in the device list you can complete the configuration e To use a web interface Web Manager double click the unit in the list and click the Web Configuration tab See Configuration Using Web Manager on page 10 e To use a Command Line Interface double click the unit in the list and click the Telnet Configuration tab Note Please see your product s User Guide and Command Reference for detailed instructions on configuration WWW LANTRONIX COM 9 1 14 10 9 15 44 AM Quick Start Guide EDS1100 2100 CONFIGURATION USING WEB MANAGER In this Quick Start Guide we briefly describe how to configure the EDS using Web Manager Lantronix s browser based configuration tool For detailed information on Web Manager configuration and on other methods please see the User Guide for your product 1 Perform one of the following steps e Using Devicelnstaller select the unit select the Web Configuration tab and click Go Open a web browser and enter the IP address of the EDS to open Web Manager 2 Enter your User Name default is admin and Password default is PASS The EDS Web Manager window displays 09276LTX_QSG_1100_2100_7 indd 13 14 EDS2100 Powered by Evolution 0S Device Status Product Information Product Type
4. international adapters Power Cord Restraint PINOUTS RS 232 Pin Assignment RS 232 Pin Assignment TX out DTR out out CTS RX D RTS in Tx in RTS out CTS in EDS1100 EDS2100 09276LTX_QSG_1100 2100 7 indd 5 6 QUICK CONNECT Complete the following steps in order Refer to the numbers in the figure below 1 Connect a serial device to your unit 2 Connect an Ethernet cable to the RJ45 port of the unit 3 Supply power to your unit using the power cord that was included in the packaging 4 Supply power to the serial device 10 100 BASE T Ethernet Serial Device WWW LANTRONIX COM 1 14 10 9 15 42 AM 09276LTX_QSG_1100 2100 7 indd 7 8 D Quick Start Guide EDS1100 2100 IP ADDRESSING Your unit must have a unique IP address on your network The IP address can be assigned automatically or you can assign it manually DHCP Many networks use an automatic method of assigning an IP address called DHCP If you are unsure whether your network uses DHCP check with your systems administrator The EDS looks for a DHCP server when it first powers up You can use the Devicelnstaller graphical user interface to search the network if your unit has been assigned an IP address by the DHCP server If the EDS does not acquire an IP or you do not use DHCP you must assign a fixed IP address using the serial port of the EDS FIXED IP ADDRESS In most installations a fixed IP address
5. is desirable The systems administrator generally provides the IP address The IP address must be within a valid range unique to your network and in the same subnet as your PC You will need the following information before you set up the unit as described in this Quick Start Guide IP Address Subnet Mask Gateway The following section describes assigning an IP address using Devicelnstaller Note For detailed instructions on assigning the IP address using the serial port please see the User Guide or the EDS Video Tutorial on the Lantronix web site QUICK SETUP USING THE DEVICEINSTALLER UTILITY Step 1 Install Devicelnstaller To use the Devicelnstaller utility first install it from the downloads page on the Lantronix web site 1 Download the latest version of Devicelnstaller from http www lantronix com downloads 2 Run the executable to start the installation process 3 Respond to the installation wizard prompts When prompted to select an installation type select Typical Note For more information about Devicelnstaller see the Devicelnstaller Online Help Step 2 Configure Network Settings To assign an IP address manually 1 dick Start gt Programs gt Lantronix gt Devicelnstaller gt Devicelnstaller If your PC has more than one network adapter a message displays Select an adapter and click OK WWW LANTRONIX COM 5 1 14 10 9 15 43 AM Quick Start Guide EDS1100 2100
6. og box and return to the main window WWW LANTRONIX COM FA 1 14 10 9 15 44 AM Quick Start Guide EDS1100 2100 USING THE DEVICEINSTALLER UTILITY CONTINUED Step 3 Add the Unit to the Device List Now add the unit to the list of similar Lantronix devices on the network so that you can manage and configure it To perform this step click the Search icon x Devicelnstaller locates the unit and adds it to the list To view the current configuration double click the unit in the list S Lantronix Devicelnstaller 4 2 0 5B2 File Edit View Device Tools Help po Search Exclude e Assign IP Va Upgrade Fal Lantronix Devices 41 device s Device Details Web Configuration Telnet Configuration Local Area C tion 172 19 100 176 aia Loea Aea oreca ret Reload Details i EDS1100 firmware v9 9 Property B EDS2100 firmware v9 9 Name e 172 19 205 52 Group i EDS32PR firmware v4 1 Comments ag EDS 4100 firmware v4 1 Device Family EDS USING THE DEVICEINSTALLER UTILITY CONTINUED E EPS H E Intellibox E MatchPort a SCS 09276LTX_QSG_1100_2100_7 indd 11 12 Type ID Hardware Address Firmware Version Extended Firmware Version Online Status IP Address IP Address was Obtained Subnet Mask Gateway Number of Ports Supports Configurable Pins Supports Email Triggers Telnet Enabled Telnet Port Web Enabled Web Port Firmware Upgradable EDS2100 E3 00 20 44 9
7. ompleted booting Blinking 1x sec EDS firmware is booting Blinking 2x sec EDS is writing a file to flash Blinking 4x sec EDS is compacting the file system Blinking 5x sec EDS is restoring factory defaults ON EDS is receiving power Blinking EDS is transmitting data on the serial port Blinking EDS is receiving data on the serial port ON EDS firmware has completed booting Blinking 1x sec EDS firmware is booting Blinking 2x sec EDS is writing a file to flash Blinking 4x sec EDS is compacting the file system Blinking 5x sec EDS is restoring factory defaults CONTACT For questions and technical support please check our online knowledge base at www lantronix com support Lantronix 167 Technology Drive Irvine CA 92618 USA Phone 949 453 3990 or Fax 949 450 7249 www lantronix com WWW LANTRONIX COM 13 1 14 10 9 15 45 AM
8. senphzaes en Sey sa EDS1100 2100 EDS1100 2100 Quick Start Guide LANTRONIX 2010 Copyright Lantronixisa trademark of Lantronix AII rights reserved 900537 Rexa ovio M 09276LTX_QSG_1100 2100 7 indd 1 2 1 14 10 9 15 35 AM EDS1100 2100 QUICK START GUIDE CONTENTS Winata A CIB OX e sealer ret teree tan E beanie etn mene Seer eee a einer 2 PNEUS e te E oa eee an E EEEE nan 2 EDS1100 2100 Oul Glo a fat element a ee eee er E ee 3 IPAGE S MOn E Ae A EE cine ohn ne anne ene onnr eae incr nN 4 Quick Setup Using the Devicelnstaller Utility 4 23 22 2 22209 0 2 5 se sse ons 5 9 Configuration Using Web WManaGehe sesso es ce 10 11 BE Severe eee E Se ace tnd ode de Sol tee Ba rae Maaideran Tats So en 12 COMICE E E E scat eae ee ane E 13 09276LTX_QSG_1100_2100_7 indd 3 4 1 14 10 9 15 39 AM Quick Start Guide EDS1100 2100 The EDS products allow serial devices to connect and communicate over an Ethernet network This Quick Start Guide will step you through hardware installation and initial configuration of your EDS1100 or EDS2100 WHAT S IN THE BOX In addition to the EDS1100 or EDS2100 the box contains the following items EDS1100 PART COMPONENT DESCRIPTION 500 163 R DB25M to DB9F serial cable 520 090 R Power Cube 100 240VAC with international adapters Power Cord Restraint EDS2100 PART COMPONENT DESCRIPTION 500 164 R DB9F to DB9F serial cable 520 090 R Power Cube 100 240VAC with
Download Pdf Manuals
Related Search