Home

Lantronix Network Hardware 2100 User's Manual

1. IntelliBox l O 2100 Command Reference 20 34 49 1 About This Guide This guide describes how to configure the IntelliBox I O 2100 using the Command Line Interface CLI and or Extensible Markup Language XML It is written for software developers and system integrators Chapter Summaries This table lists and summarizes each chapter and appendix Chapter 2 Overview Gives an overview of CLI and XML Chapter 3 Command Line Interface Lists commands and describes how to use CLI to configure the IntelliBox Chapter 4 Configuration Using XML Lists XCR groups and items and describes how to use XCRs to configure the IntelliBox Chapter 5 Commands and Levels Provides an index of the CLI Command Hierarchy with Conventions hyperlinks to the corresponding command details The table below lists and describes the conventions used in this book Bold text Italic text Brackets Angle Brackets lt gt Pipe Warning Note Caution Screen Font Courier New Default parameters Required values for parameters Optional parameters Possible values for parameters Choice of parameters Warning Means that you are in a situation that could cause equipment damage or bodily injury Before you work on any equipment you must be aware of the hazards involved with electrical circuitry and familiar with standard practices for preventing accidents Note Means take notice Notes contain helpful sugges
2. Exits to the EventTrak level Changes to the command level for EventTrak Match con figuration Removes the EventTrak ping address Sets the EventTrak output control to exclusive so if the activity is to Sets the EventTrak output control to be Logical Or so it may be combined Sets the EventTrak ping address to be used when the activity is to send rss trace ping responses disable Turns off RSS tracing of EventTrak ping responses rss trace ping responses enable rss trace steps disable rss trace steps enable rss trace triggers enable show show history IntelliBox l O 2100 Command Reference rss trace triggers disable Turns on RSS tracing of ping responses received by this EventTrak task Turns off RSS tracing of EventTrak task steps Turns on RSS tracing of each step taken by an EventTrak task Turns off RSS tracing of EventTrak task triggers Turns on RSS tracing of triggers emitted by this EventTrak task Displays the current configuration Displays the last 20 commands entered during the current CLI session 90 step lt etter gt task lt number gt write ack limit lt packets gt auto show stats clear counters clrscrn default ack limit default send data exit no clear counters resets disable resets enable send data expedited send data standard show show history show stats write break duration lt milliseconds gt clrscrn default break duration default termi
3. Sets local port used to send email alerts to random Removes the file name so the message body will be empty 53 5 Commands and Levels Removes To address for email alerts no trigger overriding domain lt domain gt priority high priority low priority normal priority urgent priority very low replyto lt email address gt send server port lt number gt show show history show log show statistics subject lt string gt to lt email addresses gt trigger lt xio1 xio2 gt lt high low gt write auto show statistics cc lt email addresses gt chem lt number gt clear log clear mail counters clrscrn exit file lt file gt rom lt email address gt local port lt number gt ocal port random no cc no clear mail counters no file no from no overriding domain no replyto no subject no to no trigger overriding domain lt domain gt IntelliBox l O 2100 Command Reference Disables the trigger to send an email Sets a domain name that will be used when connecting to an SMTP server to Displays the last 20 commands entered during the current CLI session Specifies input name and voltage level to trigger sending an email Stores the current configuration in permanent memory Specifies a text file the contents of which will be the mes sage body Sets local port used to send email alerts to random Removes the file name so the message body will be empty Sets a d
4. instance is the telnet session number state local port totals state host severity to log messages failed messages send IntelliBox l O 2100 Command Reference baud parity none even odd data bits stop bits 1 2 flow control none hardware software local port remote ip address remote port duration local port remote ip address remote port duration active waiting disabled uptime bytes in bytes out enable disable 44 4 Configuration Using XML retransmission connections errors in resets segments telnet state local port totals last connection tftp state creation downloaded uploaded not found errors last client IntelliBox l O 2100 Command Reference algorithm vanj timeout minimum timeout maximum maximum open active open passive failed resets established out retransmitted active waiting disabled uptime bytes in bytes out local ip address local port remote ip address remote port enabled disabled enabled disabled read write unknown ip address port 45 4 Configuration Using XML tunnel aggregate Attribute of instance is a number current connect connections As many as present current accept connections As many as present IntelliBox l O 2100 Command Reference completed connects completed accepts disconnects dropped connects dropped accepts octets from serial
5. missed frame errors 39 4 Configuration Using XML ip state enabled disabled default ttl forwarded route discards in receives header errors address errors unknown protocols discarded delivered out requests discards discards no route reassembly timeout needed SUCCESS failures fragments needed failures SUCCESS ip sockets ip socket protocol UDP TCP rx queue tx queue local address local port remote address remote port state IntelliBox l O 2100 Command Reference 40 4 Configuration Using XML line receiver Attribute of instance is a number transmitter line levels line lt number gt within group buffer headers puffer pool cluster pool IntelliBox l O 2100 Command Reference bytes breaks parity errors framing errors overrun errors no receive buffer errors queued bytes flow control n a stop go bytes breaks queued bytes flow control n a stop go cts asserted not asserted rts asserted not asserted dsr asserted not asserted dtr asserted not asserted total free used max used cluster size total free used max used 41 4 Configuration Using XML line With no instance Within group line on instance Ipd Attribute of instance is a number memory state protocol baud rate parity data bits stop bits flow control xon char xoff char jobs printed bytes printed current client ip address
6. a number continued state admin username admin password name protocol ssh username remote address remote port user delete realm type user Attribute of instance is the user name IntelliBox l O 2100 Command Reference upon advance clear receive buffer upon advance send line upon advance send data upon advance send file name upon advance send trigger upon advance rss upon advance rss title name password telnet ssh enable disable Default enable Default admin Value is SECRET hidden from user view Default telnet Default 0 Deletes an HTTP Authentication URI user The value element is used to specify the user for deletion 24 http server icmp input output Attribute of instance is a number state port secure port secure protocols max timeout max bytes logging state max log entries log format state input output direction control rss trace transitions IntelliBox l O 2100 Command Reference 4 Configuration Using XML enable disable amp 60 None amp 62 amp 60 None amp 62 ssl3 tls1 0 tls1 1 enable disable enable disable output input force closed force open normal enable disable Default enable Default 80 Default 443 May contain zero one or more of the values separated by commas Default ssl3 tls1 0 tls1 1 Default 10 seconds Default 40960 Defau
7. no output output lt text gt show show history write clrscrn default packing mode default threshold default timeout exit no send character no trailing character packing mode disable packing mode send character packing mode timeout send character lt control gt show show history IntelliBox l O 2100 Command Reference 5 Commands and Levels Clears the screen Requires exclusive control of the output for connect mode connection Exits to the next higher level Requires exclusive control of the output for connect mode connection Does not require exclusive control of the output for con nect mode connection Discontinues enabling any output while the connect mode connection is up Selects an output to enable while the connect mode con nection is up Shows the current configuration Displays the last 20 commands entered during the current CLI session Stores the current configuration in permanent memory Clears the screen Requires exclusive control of the output for accept mode connection Exits to the next higher level Requires exclusive control of the output for accept mode connection Does not require exclusive control of the output for accept mode connection Discontinues enabling any output while the accept mode connection is up Selects an output to enable while the accept mode con nection is up Shows the current configuration Displays the last 20 commands entered dur
8. sage body Sets the From address for email alerts Sets local port used to send email alerts Sets local port used to send email alerts to random Removes the Cc addresses for email alerts Restores the email counters to the aggregate values Removes the file name so the message body will be empty 52 no from no overriding domain no replyto no subject no to no trigger overriding domain lt domain gt priority high priority low priority normal priority urgent priority very low replyto lt email address gt send server port lt number gt show show history show log show statistics subject lt string gt to lt email addresses gt trigger lt xio1 xio2 gt lt high low gt write auto show statistics cc lt email addresses gt chem lt number gt clear log clear mail counters clrscrn exit file lt file gt from lt email address gt ocal port lt number gt local port random no cc no clear mail counters no file no from no overriding domain no replyto no subject IntelliBox l O 2100 Command Reference 5 Commands and Levels Sets a domain name that will be used when connecting to an SMTP server to Displays the last 20 commands entered during the current CLI session Specifies input name and voltage level to trigger sending an email Stores the current configuration in permanent memory Specifies a text file the contents of which will be the mes sage body
9. Trak task rss trace steps disable Turns off RSS tracing of EventTrak task steps rss trace steps enable rss trace triggers disable rss trace triggers enable show show history step lt etter gt task lt number gt write activity none activity output lt number gt activity ping clrscrn default activity efault description default output control description lt text gt exit match lt number gt no ping address output control exclusive output control logical or ping address lt text gt Turns on RSS tracing of each step taken by an EventTrak task Turns off RSS tracing of EventTrak task triggers Turns on RSS tracing of triggers emitted by this EventTrak task Displays the current configuration Displays the last 20 commands entered during the current CLI session Changes to the command level for EventTrak Task Step configuration Changes to the command level for EventTrak Task confi guration Stores the current configuration in permanent memory Sets the EventTrak task activity to None Sets the EventTrak task activity to control the designated output pin Sets the EventTrak task activity to send a ping once per second Clears the screen Sets the default EventTrak task activity which is None Removes the description of an EventTrak control task Sets the default EventTrak output control which is Exclu sive Sets the description of an EventTrak control task It will appear in
10. XML engine In both cases the device server filesystem is not accessed The file intellibox_io xcr is not read from or written to the file system See FTP in the ntelliBox l O 2100 User Guide Best Practices You can import or export an entire XCR or just a portion of it by specifying the group name and or group instances In the examples below import and export operations are performed from the CLI on the local filesystem and require a XCR on the local filesystem The Web Manager provides the same functionality Caution Using Microsoft Word to edit and save an XCR will change the format of the file and make it incompatible with Evolution OS This is true even if the file is saved as Plain Text txt or an XML Document xml Notepad a third party text editor or a specialized XML editor should be used instead Importing The following syntax can be used to import configurations from a file xcr import lt file gt xcr import lt file gt lt groups and or group instances gt The first line imports all groups specified in the XML config record named in lt file gt Any filename is valid and the file name and extension are not important Caution The filename intellibox_io xcr is not acceptable because performing a FTP get on that name produces the current configuration and does not perform an FTP from the filesystem Also the filename intellibox_io xsr is not acceptable because performing an FTP get on that name produces
11. a number number timeout milliseconds case sensitive rss trace matches task description Attribute of instance is activity a number ping address output control rss trace steps rss trace triggers rss trace ping responses IntelliBox l O 2100 Command Reference no yes amp 60 None amp 62 none ping output exclusive logical or enable disable enable disable enable disable 22 4 Configuration Using XML event trak step Attribute of Attribute of instance is instance is a a number number continued IntelliBox l O 2100 Command Reference name amp 60 None amp 62 activity advance upon advance timeout value advance timeout units fallback timeout value fallback timeout units fallback timeout enabled fallback if input high to low fallback if input low to high fallback if matched string fallback if trigger a fallback if trigger b fallback if output data present fallback if accepted connection fallback if accepted disconnection fallback if ping response upon fallback send trigger upon advance send email upon advance email subject 23 4 Configuration Using XML event trak Attribute of instance is a number continued ftp server host Attribute of instance is a number http authentication uri Attribute of instance is the URI step Attribute of instance is
12. allow file creation enable clear counters clrscrn exit no clear counters show show history state disable state enable write accept auto show statistics clear accept counters clear aggregate counters clear all counters clear connect counters IntelliBox l O 2100 Command Reference 5 Commands and Levels Disables echoing of characters received on the line back to the line Enables echoing of characters received on the line back to the line Exits to the configuration level On the login connect menu removes the menu item allow ing the user to exit On the login connect menu inserts the menu item allow ing the user to exit Enters the line level Disables the login connect menu so a user will get the CLI immediately Enables the login connect menu so a user will get the menu rather than the Enters the configure Ipd level Removes the configured send break character Shows the layout of the connect menu with current set tings Sets the optional send break character Displays the current configuration Displays the last 20 commands entered during the current CLI session Prohibits the TFTP server from creating files on the file system Displays the last 20 commands entered during the current CLI session Disables the TFTP server Enables the TFTP server Stores the current configuration in permanent memory 93 5 Commands and Levels clrscrn Clears the screen connect Enters the co
13. close the CLI session If Line Command Mode is specified as Always a new session starts immediately To view the current configuration at any level Type show To view the list of commands available at the current level Type the question mark Items within lt gt e g lt string gt are required parameters To view the available commands and explanations Type the asterisk To view the list of commands available for a partial command Type the partial command followed by the question mark For example lt tunnel 1 gt echo displays a list of all echo commands at the tunnel level To view available commands and their explanations for a partial command Type the partial command followed by the asterisk For example lt tunnel 1 gt echo displays a list of all echo commands and descriptions at the tunnel level To view the last 20 commands entered at the CLI Type show history IntelliBox l O 2100 Command Reference 10 3 Command Line Interface Using Keyboard Shortcuts and CLI One useful shortcut built into Evolution OS is that the complete text of a command does not have to be entered to issue a command Typing just enough characters to uniquely identify a command then hitting enter can be used as a short cut for a command For example at the enable level sh can be used for the show command Tab Completion is also available Typing the first few characters of a command then hitting
14. current client port last client ip address last client port main heap internal buffer heap IntelliBox l O 2100 Command Reference condition total memory available memory fragments allocated blocks condition total memory available memory fragments allocated blocks enable disable none ppp tunnel Any value from 300 to 230400 even none odd 1 2 hardware none software clean corrupt clean corrupt 42 4 Configuration Using XML modbus local slave modbus tcp server Attribute of instance is permanent or additional processes protocol stack within group buffer pool query port rss totals state local port totals process Attribute of instance is a number buffer headers cluster pool status last connection out url data IntelliBox l O 2100 Command Reference pdus in pdus out exceptions down up binding no port uptime pdus in pdus out connections cpu stack used stack size thread name total free used max used cluster size total free used max used enabled disabled ip address port discoveries unknown queries erroneous packets discovery replies errors entries bytes 43 4 Configuration Using XML sessions ssh syslog line Attribute of instance is a number ssh Attribute of instance is the ssh session number telnet Attribute of
15. default dtr dtr asserted while connected tr continuously asserted dtr unasserted show history write IntelliBox l O 2100 Command Reference 5 Commands and Levels Show system information Trace route to destination Displays the last 20 commands entered during the current CLI session Display the RSS Feed status Stores the current configuration in permanent memory Sets the size of the buffer for data read from the serial port Clears the screen Restores the default buffer size Restores default DTR control asserted while connected Asserts DTR whenever a connect or accept mode tunnel connection is active Displays the last 20 commands entered during the current CLI session Stores the current configuration in permanent memory Sets the size of the buffer for data read from the serial port Clears the screen Restores the default buffer size Restores default DTR control asserted while connected Asserts DTR whenever a connect or accept mode tunnel connection is active Displays the last 20 commands entered during the current CLI session Stores the current configuration in permanent memory 83 clrscrn community ro lt string gt community rw lt string gt contact lt string gt efault description description lt string gt exit host lt ip address gt host lt ip address gt lt ip address gt ocation lt string gt name lt string gt no community ro no community rw no contact no
16. gt lt group list gt xcr import lt file gt lt group list gt xsr dump xsr export lt file gt xsr list lt line gt lt enable gt auto show processes chem lt number gt clear query port counters clrscrn connect device exit io kill ssh lt session gt line lt line gt no clear interfaces counters no clear xsr counters nslookup lt host gt ping lt host gt lt count gt reload secret xcr dump secret xcr export lt file gt show show hosts show interfaces show processes show xsr ssh lt optClientUsername gt lt host gt ssl telnet lt host gt lt port gt tunnel lt line gt xcr dump xcr export lt file gt xcr import lt file gt xer list xsr dump lt group list gt xsr export lt file gt lt group list gt See the Chapter 5 Commands and Levels at the end of this document for a complete list of levels commands and descriptions IntelliBox l O 2100 Command Reference 13 4 Configuration Using XML The device server provides an Extensible Markup Language XML interface that you can use to configure device server devices Every configuration setting that can be issued from the device server Web Manager and CLI can be specified using XML The device server can import and export configuration settings as an XML document known as an XML Configuration Record XCR An XCR can be imported or exported via the CLI a Web browser FTP or the device server filesystem An XCR
17. is a current step number step name filesystem filesystem entries IntelliBox l O 2100 Command Reference product type serial number firmware version uptime permanent config saved unsaved sent sent with retries time log total free used max used cluster size total free used max used size available clean available dirty used total used data busy file count directory count system count open count lock count share count 35 4 Configuration Using XML filesystem continued ftp hardware http http log banks status admin username connections last client cpu hardware id memory state ports max timeout max bytes logging entry Attribute of instance is a number totals IntelliBox l O 2100 Command Reference current firmware begin firmware end firmware erase cycles bank a begin bank a end bank a erase cycles bank b begin bank b end bank b erase cycles running inactive admin rejected accepted ip address port type speed hardware id flash size ram size enabled disabled entries bytes entries bytes 36 4 Configuration Using XML icmp in out inputs and outputs xio1 xio2 Relay IntelliBox l O 2100 Command Reference messages messages discarded errors destination unreachable time exceeded messages parameter problems source quench requests redirects ping requests ping r
18. lt configgroup gt Importing and Exporting an XML Configuration File An XCR can be imported or exported using the following methods e Filesystem XCRs can be saved to the device server file system and imported or accessed as needed See Best Practices o Guide r the Filesystem Browser section in the ntelliBox I O 2100 User CLI XCRs can be imported captured or exported dumped directly to a Telnet SSH or serial line CLI session Capturing an XCR can be started by pasting a valid XCR directly into the CLI prompt Evolution OS IntelliBox l O 2100 Command Reference immediately processes the configuration record changing any 17 4 Configuration Using XML settings specified This can be done on any level including the root Special tags in the XML allow for providing root and enable level passwords so that this can also be done at the password prompt Web browser Web Manager can be used to import and export an XCR to the device server file system It can also be used to import an XCR from an external source such as your local hard drive FTP The device server FTP server can export and import XCRs when an FTP get or put command on the filename intellibox_io xcr is requested On export FTP get of intellibox_io xcr the FTP server obtains the current XCR from Evolution OS and sends it as a file On import FTP put of intellibox_io xcr the FTP server processes the file by sending it directly to the
19. match 2 2 e match 3 config eventtrak match 2 3 e task 1 config eventtrak task 2 1 e task 2 config eventtrak task 2 2 e task 3 config eventtrak task 2 3 e ftp config ft e host 1 config host 1 e host 2 config host 2 e http config htt e icmp config icmp e if 1 config if ethO e link config ethernet ethO e ip config ip e ip filter config filter e ipd 1 _ config lpd 1 e ipd 2 config lpd 2 e modbus modbus uery port config query_port e rss config rss e snmp config snm e syslog config sysloq e tcp config tcp e terminal 1 config terminal 1 e terminal 2 config terminal 2 e terminal network config terminal network e tftp config tft e udp config udp e device device e filesystem filesystem e io iO IntelliBox l O 2100 Command Reference 5 Commands and Levels line 1 line 1 line 2 line 2 lod Ipd ssh ssh ssl ssl tunnel 1 tunnel 1 e accept tunnel accept 1 e output select tunnel accept output select 1 e connect tunnel connect 1 e output select tunnel connect output_ select 1 disconnect tunnel disconnect 1 modem tunnel modem 1 packing tunnel packing 1 e serial tunnel serial 1 e tunnel 2 tunnel 2 e accept tunnel accept 2 e output select tunnel accept outoput select 2 e connect tunnel connect 2 e output select tunnel connect output_ select 2 disconnect tunnel disconnect 2 modem tunnel modem 2 packing tunnel packing 2 seri
20. takes the name attribute and must contain one or more value elements For example the line group might have parameters such as baud rate data bits and parity A value may specify the value of a configuration parameter It may contain the name attribute In this example a value of 9600 might be specified for baud rate 7 may be specified for data bits and even may be specified for parity A name attribute identifies the group item or value It is always quoted as are all XML attributes For example a group that contains serial port parameters has the name line An instance attribute identifies which of several instances is being addressed It is always quoted For example the serial port name in the line configgroup has the instance 1 to indicate serial port 1 or 2 to specify serial port 2 The following figures show examples of XML configuration records and the use of the lt configrecord gt lt configgroup gt lt configitem gt and lt value gt XML elements Figure 4 3 XML Group Example lt xml version 1 0 standalone yes gt lt configrecord gt lt configgroup name serial command mode instance 1 gt lt configitem name mode gt lt value gt disable lt value gt lt configitem gt lt configgroup gt lt configrecord gt Figure 4 4 XML Example of Multiple Named Values lt xml version 1 0 standalone yes gt lt configgroup name
21. tcp aes protocol telnet rss trace connections disable rss trace connections enable show show history show status tcp keep alive lt milliseconds gt write add lt P address gt lt MAC address gt clrscrn default timeout exit remove lt P address gt remove all show show cache show history timeout lt seconds gt write auto show statistics cc lt email addresses gt chem lt number gt clear log clear mail counters clrscrn exit file lt file gt from lt email address gt local port lt number gt local port random no cc no clear mail counters no file IntelliBox l O 2100 Command Reference 5 Commands and Levels Uses TCP protocol with AES encryption for accept mode tunneling Uses Telnet protocol with IAC for accept mode tunne ling Disables RSS Trace of accept mode connections Enables RSS Trace of accept mode connections Displays the current configuration Displays the last 20 commands entered during the current CLI session Displays tunnel accept status Enables TCP keep alive for accept mode tunneling and sets the timer Stores the current configuration in permanent memory Adds an entry to the ARP table mapping an IP address to a MAC address Displays the last 20 commands entered during the current CLI session Sets the ARP cache timeout Stores the current configuration in permanent memory Specifies a text file the contents of which will be the mes
22. the current status and does not get anything from the filesystem In the second line Instance follows group with a colon see the third example on the next page Multiple groups are separated with a comma Any white space requires the list of groups to be quoted Only the named groups get imported even if the XCR contains additional XCR groups IntelliBox l O 2100 Command Reference 18 4 Configuration Using XML The following syntax can be used to export configurations to a file on the device server s file system xcr export lt file gt xcr export lt file gt lt groups and or group instances gt The same guidelines above regarding importing configurations also apply to exporting configurations If no groups are specified then the export command will export all configuration settings to the file If instances are specified after the groups only those group instances are written If no instance is specified all instances of that group are written Exporting The following example exports only the accept mode tunneling settings for line 1 to the file tunnel_1 xcr on the device server filesystem xcr export tunnel_l xcr tunnel accept 1 The following example exports only the connect mode tunneling settings for all ports to the file tunnel_all xcr on the device server filesystem xcr export tunnel_all xcr tunnel connect The following example imports only the settings for line 2 from a X
23. to connect to the host Displays the current configuration Displays the last 20 commands entered during the current CLI session Sets the username for logging into the host via SSH Stores the current configuration in permanent memory Creates a new HTTP server authentication directive Sets an HTTP server authentication directive to the Basic Access Sets an HTTP server authentication directive to the Digest Access Sets the authentication type for an HTTP server authenti cation directive to Sets the authentication type for an HTTP server authenti cation directive to SSL Sets the authentication type for an HTTP server authenti cation directive Sets the authentication type for an HTTP server authenti cation directive Creates or modifies a user for an HTTP server authentica tion directive Sets the HTTP counters to zero Clears the HTTP server log Clears the screen Restores the HTTP Server log format string to its default value Restores the default maximum number of HTTP Server log entries Resets the default maximum bytes the HTTP Server will accept when receiving Resets the default maximum time the HTTP Server will wait when receiving Resets the HTTP Server port to its default value Resets the HTTP Server SSL port to its default value Deletes an existing HTTP Server authentication directive Deletes an existing user for an HTTP Server authentica tion directive Returns to the config level Disable
24. to send an email alert upon establishing email disconnect lt number gt exit flush serial disable flush serial enable kill connection local port lt number gt no aes decrypt key no aes encrypt key no email connect no email disconnect no remote address no remote port no ssh username no tcp keep alive output select protocol ssh protocol ssl protocol tcp protocol tcp aes protocol telnet protocol udp protocol udp aes reconnect time lt milliseconds gt remote address lt text gt remote port lt number gt show show history show status ssh username lt text gt tcp keep alive lt milliseconds gt write IntelliBox l O 2100 Command Reference Sets an email profile to use to send an email alert upon closing Returns to the tunnel level Characters already in the serial data buffer are retained upon establishing Flushes the serial data buffer upon establishing a connect mode tunneling Disconnects the active connect mode tunneling connec tion Sets a specific port for use as the local port Removes the connect tunnel AES decrypt key Removes the connect tunnel AES encrypt key Discontinues sending email alerts upon establishing a connect mode tunnel Discontinues sending email alerts upon closing a connect mode tunnel Removes the remote host address used to establish tunneling connections Removes the remote port used to establish tunnel con nections Uses TCP protocol with AES encry
25. to the command level for UDP configuration and status Stores the current configuration in permanent memory Sets the connect tunnel AES decrypt key with up to 16 bytes Sets the connect tunnel AES decrypt key with up to 16 bytes Sets the connect tunnel AES encrypt key with up to 16 bytes Sets the connect tunnel AES encrypt key with up to 16 bytes Forwards tunnels network data in connect mode tunne ling Discards all data coming in from the connect mode tunnel before forwarding Forwards tunnels serial data in connect mode tunneling Discards all data coming in from the serial interface before forwarding Clears the screen Enables the tunneling server to always establish tunneling 57 5 Commands and Levels oo econnestionss connect mode any character connect mode disable connect mode modem control asserted connect mode modem emulation connect mode start character default connect mode default local port efault protocol default reconnect time default tcp keep alive email connect lt number gt email disconnect lt number gt exit flush serial disable flush serial enable kill connection ocal port lt number gt no aes decrypt key no aes encrypt key no email connect no email disconnect no remote address no remote port no ssh username no tcp keep alive output select protocol ssh protocol ssl protocol tcp protocol tcp aes protocol telnet protocol udp IntelliBox l O
26. 0 Command Reference terminal type login connect menu exit connect menu send break break duration echo state allow file creation accept mode local port protocol tcp keep alive aes encrypt key aes decrypt key flush serial block serial block network password email connect email disconnect password prompt 4 Configuration Using XML enable disable enable disable enable disable enable disable enable disable disable always any character start character modem control asserted modem emulation amp 60 None amp 62 tcp ssh telnet tcp aes ssl amp 60 None amp 62 enable disable enable disable enable disable enable disable amp 60 None amp 62 amp 60 None amp 62 Default UNKNOWN Default disable Default disable Accepts a control character for example amp 60 control amp 62 A represents control A Default 500 milliseconds Default enable Default enable Default disable Default always Default lt None gt Default tcp Default 45000 milliseconds Value is SECRET hidden from user view Value is SECRET hidden from user view Default disable Default disable Default disable Value is SECRET hidden from user view Default disable Default lt None gt Default lt None gt 31 tunnel connect Attribute of instance is a number tunnel disconnect Attrib
27. 2100 Command Reference Enables the tunneling server to establish a tunneling con nection when a Disables connect mode tunneling Enables the tunneling server to make tunneling connec tions when the modem Enables modem emulation for connect mode tunneling Enables connect mode tunneling when the configured start character Restores the default connect mode as disable Uses a random port number as the local port for establish ing tunneling Restores the default protocol as TCP Restores the default reconnect time value for connect mode tunneling Restores the default 45 second connect mode TCP keep alive timeout Sets an email profile to use to send an email alert upon establishing Sets an email profile to use to send an email alert upon closing Returns to the tunnel level Characters already in the serial data buffer are retained upon establishing Flushes the serial data buffer upon establishing a connect mode tunneling Disconnects the active connect mode tunneling connec tion Sets a specific port for use as the local port Removes the connect tunnel AES decrypt key Removes the connect tunnel AES encrypt key Discontinues sending email alerts upon establishing a connect mode tunnel Discontinues sending email alerts upon closing a connect mode tunnel Removes the remote host address used to establish tunneling connections Removes the remote port used to establish tunnel con nections Uses TCP
28. CR named factory_config xcr on the device server filesystem If factory_config xcr has other configuration settings they are ignored xcr import factory_config xcr line 2 The following example imports only line settings for all ports from a configuration record on the device server filesystem named foobar xcr xcr import foobar xcr line To import only disconnect mode tunneling settings for port 1 and serial line settings for port 2 from an XML configuration record named production xcr that contains these settings and possibly more issue the following command xcr import production xcr tunnel disconnect 1 line 2 The following example imports all tunneling settings and line settings for all serial ports from a file named xcr_file xcr import xcr_file tunnel accept tunnel connect tunnel disconnect tunnel modem tunnel packing tunnel serial tunnel start tunnel stop line The following example exports only accept mode tunneling settings on serial port 1 and line settings on serial port 2 to a file named tunnel_config_t1_l2 xcr on the device server filesystem xcr export tunnel_config_t1_12 xcr tunnel accept 1 line 2 The following example exports connect mode tunneling and line settings for all ports to the file tunnel_config xcr on the device server filesystem xcr export tunnel_config xcr tunnel line Passwords in the XML File If you log in to a device server to which y
29. LANTRONIX IntelliBox I O 2100 Command Reference Part Number 900 475 Revision B March 2012 Copyright and Trademark 2012 Lantronix All rights reserved No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of Lantronix Printed in the United States of America Ethernet is a trademark of XEROX Corporation UNIX is a registered trademark of The Open Group Windows is a trademark of Microsoft Corporation Contacts Lantronix Corporate Headquarters 167 Technology Drive Irvine CA 92618 USA Toll Free 800 526 8766 Phone 949 453 3990 Fax 949 450 7249 Technical Support Online www lantronix com support Sales Offices For a current list of our domestic and international sales offices go to the Lantronix web site at www lantronix com about contact Disclaimer The information in this guide may change without notice The manufacturer assumes no responsibility for any errors that may appear in this guide For the latest revision of this product document please check our online documentation at www lantronix com support documentation Revision History May 2007 A Initial Document March 2012 B Updated for firmware v1 4 0 0 R2 IntelliBox l O 2100 Command Reference 2 Table of Contents a 3 List of Figures 4 List of Tables 5 About This Guide 6 Chapter Summaries 6 Conventions 6 Additional Documentation 7 2 Overview XML Ar
30. ad of gt and the Web Manager is inaccessible These serve as an important indication that the device boot processes has been temporarily halted To complete the boot process terminate the serial CLI session with the exit command IntelliBox l O 2100 Command Reference 9 3 Command Line Interface To configure the Lantronix device server locally using a serial port connect a terminal or a PC running a terminal emulation program to one of the device server s serial ports Configure the terminal for 9600 baud 8 bit no parity 1 stop bit and no flow control 1 Power off the device Press and hold down the exclamation point key Power on the device After about ten seconds the exclamation point will display on the terminal or PC screen Type xyz within 5 seconds to display the CLI prompt Navigating the CLI Hierarchy The CLI is organized into a hierarchy of levels Each level has a group of commands for a specific purpose For example to configure a setting for the FTP server one would navigate to the FTP level which is under the configuration level To move to a different level Enter the name of the level from within its parent level For example to enter the tunnel level type tunnel lt number gt at the enable prompt This displays lt enable gt tunnel lt number gt To exit and return to one level higher Type exit and press the Enter key Typing exit at the login level or the enable level will
31. age no name parity even parity none parity odd protocol Ipd IntelliBox l O 2100 Command Reference Uses hardware RTS CTS flow control on the line Does not provide flow control on the line Uses software xon xoff characters flow control on the line Prevents the user defined serial boot string from being used to enter Clears the signon message displayed at boot time and when entering Applies Line Printer Daemon LPD protocol on the line 71 protocol Ipd or tunnel protocol modbus ascii protocol modbus rtu protocol none protocol tunnel reassert show show command mode show history show line show statistics state disable state enable stop bits 1 stop bits 2 terminal lt ine gt terminal network termination disable termination enable tunnel lt line gt write xoff char lt control gt xon char lt control gt clrscrn default duplex default speed uplex auto duplex full duplex half show history speed 10 speed 100 speed auto write auto show lt line gt clrsern exit IntelliBox l O 2100 Command Reference 5 Commands and Levels Applies Modbus RTU protocol on the line Displays the last 20 commands entered during the current CLI session Enables 120 ohm line termination in RS485 half duplex mode Enters the tunnel level Stores the current configuration in permanent memory Sets the xoff character for use with software flow control on this line Sets the xon c
32. al tunnel serial 2 Table 5 1 Commands and Levels accept mode always Enables the tunneling server to always accept tunneling connections accept mode any character Enables the tunneling server to accept tunneling connec tions only when a accept mode disable Disables accept mode tunneling accept mode modem control asserted Enables the tunneling server to accept tunneling connec tions when the modem accept mode modem emulation Enables modem emulation for accept mode tunneling accept mode start character Enables accept mode tunneling when the configured start character aes decrypt key lt hexadecimal gt Sets the accept tunnel AES decrypt key with up to 16 bytes aes decrypt key text lt fext gt Sets the accept tunnel AES decrypt key with up to 16 bytes aes encrypt key lt hexadecimal gt Sets the accept tunnel AES encrypt key with up to 16 bytes aes encrypt key text lt fext gt Sets the accept tunnel AES encrypt key with up to 16 bytes block network disable Forwards tunnels network data in accept mode tunne ling IntelliBox l O 2100 Command Reference 49 5 Commands and Levels block network enable Discards all data coming in from the accept mode tunnel before forwarding block serial disable block serial enable clrscrn default accept mode efault protocol default tcp keep alive email connect lt number gt email disconnect lt number gt exit flush serial disable flush serial enable kill
33. aximum allowed concurrent incoming SSH sessions Changes to the command level for ARP configuration and status Removes an entry from the DNS Cache Change to menu level for CLI configuration and status Clears the screen 56 eventtrak lt number gt exit tp ost lt number gt if lt instance gt ip filter kill ssh lt session gt kill telnet lt session gt Ipd lt line gt modbus query port show show history snmp syslog tcp terminal lt line gt terminal network tftp udp write aes decrypt key lt hexadecimal gt aes decrypt key text lt text gt aes encrypt key lt hexadecimal gt aes encrypt key text lt text gt block network disable block network enable block serial disable block serial enable clrsern connect mode always IntelliBox l O 2100 Command Reference 5 Commands and Levels Changes to the command level for EventTrak configura tion Changes to the command level for ICMP configuration and status Changes to the interface configuration level Changes to the command level for IP configuration and status Kills Telnet session with index from show sessions Displays the last 20 commands entered during the current CLI session Enters the snmp level Enters the syslog level Changes to the command level for TCP configuration and status Enters the configure terminal level Enters the configure terminal level for the network Enters the tftp level Changes
34. can contain many configuration settings or just a few For example it might change all of the configurable parameters for a device server or it may only change the baud rate for a single serial line Using XCRs is a straightforward and flexible way to manage the configuration of multiple device server devices XML Configuration Record Document Type Definition An XML document type definition DTD is a description of the structure and content of an XML document It verifies that a document is valid XCRs are exported using the DTD shown in Figure 4 1 Figure 4 1 DTD for XCRs lt DOCTYPE configrecord lt ELEMENT configrecord configgroupt gt lt ELEMENT configgroup configitemt gt lt ELEMENT configitem valuet gt lt ELEMENT valu PCDATA gt lt ATTLIST configrecord version CDATA IMPLIED gt lt ATTLIST configgroup name CDATA IMPLIED gt lt ATTLIST configgroup instance CDATA IMPLIED gt lt ATTLIST configitem name CDATA IMPLIED gt lt ATTLIST value name CDATA IMPLIED gt The device server DTD rules state the following The XML document element is a lt configrecord gt element This is the root element A lt configrecord gt must have one or more lt configgroup gt elements and can have a version attribute e A lt configgroup gt must have one or more lt configitem gt elements and can
35. ce to RS485 in full duplex mode Sets the line interface to RS485 in half duplex mode 69 ine lt line gt Ipd lt line gt name lt text gt no clear line counters no command mode no command mode serial string no command mode signon message no name arity even parity none parity odd protocol Ipd protocol Ipd or tunnel protocol modbus ascii protocol modbus rtu protocol none protocol tunnel reassert show show command mode show history show line show statistics state disable state enable stop bits 1 stop bits 2 terminal lt line gt terminal network termination disable termination enable tunnel lt line gt write xoff char lt control gt xon char lt control gt auto show statistics baud rate lt bits per second gt clear line counters clrscrn command mode always IntelliBox l O 2100 Command Reference 5 Commands and Levels Prevents the user defined serial boot string from being used to enter Clears the signon message displayed at boot time and when entering Applies Line Printer Daemon LPD protocol on the line Applies Modbus ASCII protocol on the line Displays the last 20 commands entered during the current CLI session Enables 120 ohm line termination in RS485 half duplex mode Enters the tunnel level Stores the current configuration in permanent memory Sets the xoff character for use with software flow control on this line Sets the xon character for use with sof
36. chitecture and Device Control 8 Command Line Interface 8 Command Line Interface 9 Configuration Using Telnet 9 Configuration Using Serial Ports 9 Serial Command Mode 9 Serial Recovery 9 Navigating the CLI Hierarchy 10 Using Keyboard Shortcuts and CLI 11 Understanding the CLI Level Hierarchy 11 4 Configuration Using XML 14 XML Configuration Record Document Type Definition 14 Quick Tour of XML Syntax 15 Declaration 15 Element Start and End Tags 15 Element Attributes 15 Record Group Item and Value Tags 16 Importing and Exporting an XML Configuration File 17 Best Practices 18 Importing 18 Exporting 19 Passwords in the XML File 19 XML Configuration Groups 20 XML Status Record Groups and Items 34 5 Commands and Levels 48 IntelliBox l O 2100 Command Reference 3 List of Figures Figure 3 1 CLI Level Hierarchy Figure 3 2 Login Level Commands Figure 3 3 Enable Level Commands Figure 4 1 DTD for XCRs Figure 4 2 XML Example Figure 4 3 XML Group Example Figure 4 4 XML Example of Multiple Named Values Figure 4 5 XML Example of Multiple Items Figure 4 6 XML Example with Multiple Groups Figure 4 7 XML Example of Supplying Passwords IntelliBox l O 2100 Command Reference 12 12 13 14 15 16 16 17 17 20 List of Tables Table 4 8 XCR Groups Table 4 9 XSR Groups and Items Table 5 1 Commands and Levels
37. com groups enable disable cpm group delete name delete http authentication enable disable Deletes existing uris http authentication uris before importing new ones http authentication uri name Deletes the delete specified http authentication uri reboot enable disable Reboots after importing XML Status Record Groups and Items Table 4 9 lists the supported XML Status Record XSR groups and items These groups and items show the status of the device in XML form and can only be exported The XSR schema differs slightly from the XCR groups and items in that the XSR allows groups within groups Currently the only XSR groups that contain any sub groups are buffer pools and tunnel The buffer pools group has the following sub groups e Protocol stack Ethernet driver Line The tunnel group has the following sub groups e Tunnel Modem Table 4 9 XSR Groups and Items arp entry ip address Gates of instance is mac address ethO age type dynamic static buffer pool this group contains other groups ethernet driver line protocol stack IntelliBox l O 2100 Command Reference 34 4 Configuration Using XML device product info email success Attribute of instance is a number failed queued email log entry Attribute of instance is a number ethernet driver buffer headers Within group buffer pool cluster pool eventtrak task description Attribute of instance
38. connection local port lt number gt no aes decrypt key no aes encrypt key no email connect no email disconnect no local port no tcp keep alive output select password protocol ssh protocol ssl protocol tcp protocol tcp aes protocol telnet rss trace connections disable rss trace connections enable show show history show status tcp keep alive lt milliseconds gt write IntelliBox l O 2100 Command Reference Forwards tunnels serial data in accept mode tunneling Discards all data coming in from the serial interface before forwarding Clears the screen Restores the default accept mode as always Restores the default protocol as TCP Restores the default 45 second accept mode TCP keep alive timeout Sets an email profile to use to send an email alert upon establishing Sets an email profile to use to send an email alert upon closing Returns to the tunnel level Characters already in the serial data buffer are retained upon establishing Flushes the serial data buffer upon establishing an accept mode tunneling Discontinues sending email alerts upon establishing an accept mode tunnel Discontinues sending email alerts upon closing an accept mode tunnel Uses the default port number as the local port for accept mode tunneling Uses TCP protocol with AES encryption for accept mode tunneling Uses Telnet protocol with IAC for accept mode tunne ling Disables RSS Trace of accept mode connec
39. control Sets the default EventTrak output control which is Exclu sive description lt text gt Sets the description of an EventTrak control task It will appear in exit Exits to the EventTrak level IntelliBox l O 2100 Command Reference 88 5 Commands and Levels match lt number gt Changes to the command level for EventTrak Match con figuration no ping address Removes the EventTrak ping address output control exclusive Sets the EventTrak output control to exclusive so if the activity is to output control logical or Sets the EventTrak output control to be Logical Or so it may be combined ping address lt text gt Sets the EventTrak ping address to be used when the activity is to send rss trace ping responses disable Turns off RSS tracing of EventTrak ping responses rss trace ping responses enable Turns on RSS tracing of ping responses received by this EventTrak task rss trace steps disable Turns off RSS tracing of EventTrak task steps rss trace steps enable Turns on RSS tracing of each step taken by an EventTrak task rss trace triggers disable Turns off RSS tracing of EventTrak task triggers rss trace triggers enable Turns on RSS tracing of triggers emitted by this EventTrak task show Displays the current configuration show history Displays the last 20 commands entered during the current CLI session step lt etter gt Changes to the command level for EventTrak Task Step configuration task lt
40. cted and provides access to high level status a few diagnostic commands and the enable level Further device information and configuration are accessed via the enable level The enable level can also be password protected and is the gateway to full configuration and management of the device server There are commands for gathering and effecting all elements of device status and configuration as well as commands that take you to additional levels For instance tunnel specific status and configuration is found under the tunnel level and network specific status and configuration commands are found under the configuration level An overview of the levels in the IntelliBox is presented in Figure 3 1 IntelliBox l O 2100 Command Reference 11 3 Command Line Interface Figure 3 1 CLI Level Hierarchy login enable chom lt number gt configure device filesystem io line lt line gt Ipd ssh ssl arp cli eventtrak match number lt number gt task lt number gt ftp host lt number gt tunnel lt line gt http icmp accept if 1 j ethernet link connect ip disconnect ip filter modem Ipd lt number gt packing modbus serial query port rss snmp syslog tcp termina
41. ctions Enables TCP keep alive for connect mode tunneling and sets the timer Stores the current configuration in permanent memory Sets the connect tunnel AES decrypt key with up to 16 bytes Sets the connect tunnel AES decrypt key with up to 16 bytes Sets the connect tunnel AES encrypt key with up to 16 bytes Sets the connect tunnel AES encrypt key with up to 16 bytes Forwards tunnels network data in connect mode tunne ling Discards all data coming in from the connect mode tunnel before forwarding Forwards tunnels serial data in connect mode tunneling Discards all data coming in from the serial interface before forwarding Clears the screen Enables the tunneling server to always establish tunneling connections Enables the tunneling server to establish a tunneling con nection when a Disables connect mode tunneling Enables the tunneling server to make tunneling connec tions when the modem Enables modem emulation for connect mode tunneling Enables connect mode tunneling when the configured start character Restores the default connect mode as disable Uses a random port number as the local port for establish ing tunneling Restores the default protocol as TCP Restores the default reconnect time value for connect mode tunneling Restores the default 45 second connect mode TCP keep alive timeout 59 5 Commands and Levels email connect lt number gt Sets an email profile to use
42. ddress gt secondary dns lt P address gt show show history show status write get lt io gt no rss trace lt input gt rss trace lt input gt set lt io gt as input set lt io gt as output set lt output gt force closed set lt output gt force open set lt outout gt normal show show history auto show stats clear counters clrscrn default multicast time to live exit multicast time to live lt hops gt no clear counters show show history show stats write IntelliBox l O 2100 Command Reference Displays the last 20 commands entered during the current CLI session Show interface status Stores the current configuration in permanent memory Displays the last 20 commands entered during the current CLI session Continuously shows IP statistics Clears the screen Restores the default IP multicast time to live which is one hop Displays the last 20 commands entered during the current CLI session Shows IP statistics Stores the current configuration in permanent memory 68 5 Commands and Levels add lt ip address gt lt subnet mask gt Adds an entry to the IP filter table clrscrn exit remove lt ip address gt lt subnet mask gt show show history write auto show statistics baud rate lt bits per second gt clear line counters clrscrn command mode always command mode echo serial string disable command mode echo serial string enable command mode serial strin
43. e is a number tunnel serial Attribute of instance is a number tunnel start Attribute of instance is a number tunnel stop Attribute of instance is a number echo pluses echo commands verbose response response type error unknown commands incoming connection connect string display remote ip packing mode timeout threshold send character trailing character dtr buffer size start character echo stop character echo IntelliBox l O 2100 Command Reference 4 Configuration Using XML enable disable enable disable enable disable text numeric enable disable disabled automatic manual enable disable disable timeout send character asserted while connected continuously asserted unasserted truport enable disable enable disable Default disable Default enable Default enable Default text Default disable Default disabled Default disable Default disable Default 1000 milliseconds Default 512 bytes Accepts a control character for example amp 60 control amp 62 A represents control A Default lt control gt M Accepts a control character for example amp 60 control amp 62 A represents control A Default asserted while connected import export import export import export import export 33 4 Configuration Using XML xml import restore factory control configuration delete
44. e host to the default value Sets the IP address of the remote host to connect to when this host is Sets the remote port used to connect to the host Displays the current configuration Displays the last 20 commands entered during the current CLI session Sets the username for logging into the host via SSH Stores the current configuration in permanent memory Clears the screen Restores the default value of the protocol Telnet Sets the remote port used to connect to the host to the default value 65 no remote address no ssh username protocol ssh protocol telnet remote address lt text gt remote port lt number gt show show history ssh username lt text gt write auth lt uri gt lt realm gt auth type lt uri gt basic auth type lt uri gt digest auth type lt uri gt none auth type lt uri gt ssl auth type lt uri gt ssl basic auth type lt uri gt ssl digest auth user lt uri gt lt user gt lt password gt clear counters clear log clrscrn default log format default log max entries default max bytes default max timeout default port default ssl port delete auth lt uri gt delete auth user lt uri gt lt user gt exit log disable log enable log format lt string gt max bytes lt bytes gt IntelliBox l O 2100 Command Reference 5 Commands and Levels Sets the IP address of the remote host to connect to when this host is Sets the remote port used
45. e of instance is a number modbus query port IntelliBox l O 2100 Command Reference name interface termination state protocol baud rate parity data bits stop bits flow control xon char xoff char banner binary soj eoj formfeed convert newline soj text eoj text queue name tcp server state additional port response timeout state 4 Configuration Using XML rs232 rs485 half duplex rs485 full duplex enable disable enable disable none tunnel ppp Ipd even none odd 7 8 1 2 none hardware software enable disable enable disable enable disable enable disable enable disable enable disable enable disable amp 60 None amp 62 Default Default disable Default depends on instance Default Default 9600 bits per second Default none Default 8 Default 1 Default none Accepts a control character for example amp 60 control amp 62 A represents control A Default lt control gt Q Accepts a control character for example amp 60 control amp 62 A represents control A Default lt control gt S Default enable Default disable Default disable Default disable Default disable Default disable Default disable Default lt None gt Default 3000 milliseconds 27 serial command mode Attribute of instance is a number snmp IntelliBox l O 2100 Command Reference feed p
46. ect menu inserts the menu item allow ing the user to exit Enters the line level Disables the login connect menu so a user will get the CLI immediately Enables the login connect menu so a user will get the menu rather than the Enters the configure Ipd level Removes the configured send break character Shows the layout of the connect menu with current set 91 5 Commands and Levels SiG O SSC S SC S send break lt control gt Sets the optional send break character Displays the current configuration show history terminal lt line gt terminal network terminal type lt text gt tunnel lt line gt write break duration lt milliseconds gt clrscrn default break duration default terminal type echo disable echo enable exit exit connect menu disable exit connect menu enable line lt line gt login connect menu disable login connect menu enable Ipd lt line gt no send break preview connect menu send break lt control gt show show history terminal lt line gt terminal network terminal type lt text gt tunnel lt line gt write break duration lt milliseconds gt clrscrn default break duration default terminal type IntelliBox l O 2100 Command Reference Displays the last 20 commands entered during the current CLI session Sets how long a break should last when it is being sent to the line Clears the screen Restores the break duration to the default value 500 m
47. eference 5 Commands and Levels Sets the product long name displayed in command mode and the Web interface Sets the product short name displayed in command mode and the Web interface Show system information Displays information about the various buffer pools Displays memory utilization by code files Displays differences in memory utilization by code files or line reference Displays information about the hardware Displays the last 20 commands entered during the current CLI session Show system information Displays memory utilization by line reference for one code file Does not flush serial data upon closing a tunneling con nection Flushes serial data buffer when a tunneling connection is closed Does not watch the modem control pin to disconnect Watches the modem control pin and disconnects if it is not asserted Disables disconnect after timeout feature for tunneling sessions Displays the current configuration Displays the last 20 commands entered during the current CLI session Disconnects when no data has been received on the line serial port for the Stores the current configuration in permanent memory 61 character stop disable character stop enable clrscrn exit flush serial disable flush serial enable modem control disable modem control enable no timeout show show history timeout lt milliseconds gt write auto show interfaces auto show processes auto s
48. enable show show history string binary lt binary gt IntelliBox l O 2100 Command Reference Sets EventTrak monitoring to be case sensitive requiring an exact match Clears the screen Sets the default EventTrak monitoring case sensitivity which is not case Restores the default EventTrak monitoring timeout Exits to the EventTrak level Changes to the command level for EventTrak Match con figuration Removes the EventTrak monitoring match string Removes the EventTrak wildcard character Turns off RSS tracing of EventTrak string matches Turns on RSS tracing to post each time EventTrak matches the string Displays the current configuration Displays the last 20 commands entered during the current CLI session Sets the EventTrak monitoring match string allowing for binary characters Sets the EventTrak monitoring match string Changes to the command level for EventTrak Task confi guration Sets the EventTrak monitoring timeout milliseconds Old data that might Sets the EventTrak monitoring wildcard character Where it is placed in the Stores the current configuration in permanent memory Sets EventTrak monitoring to be insensitive to case so either a or A will Sets EventTrak monitoring to be case sensitive requiring an exact match Clears the screen Sets the default EventTrak monitoring case sensitivity which is not case Restores the default EventTrak monitoring timeout Exits to the EventTrak l
49. entTrak level Changes to the command level for EventTrak Match con figuration 76 no string no wildcard 5 Commands and Levels Removes the EventTrak monitoring match string Removes the EventTrak wildcard character rss trace matches disable Turns off RSS tracing of EventTrak string matches rss trace matches enable Turns on RSS tracing to post each time EventTrak matches the string show Displays the current configuration show history Displays the last 20 commands entered during the current CLI session string binary lt binary gt Sets the EventTrak monitoring match string allowing for binary characters string set lt text gt Sets the EventTrak monitoring match string task lt number gt Changes to the command level for EventTrak Task confi guration timeout milliseconds lt number gt Sets the EventTrak monitoring timeout milliseconds Old data that might wildcard lt text gt Sets the EventTrak monitoring wildcard character Where it is placed in the write Stores the current configuration in permanent memory case sensitive no Sets EventTrak monitoring to be insensitive to case so either a or A will case sensitive yes Sets EventTrak monitoring to be case sensitive requiring an exact match clrscrn Clears the screen default case sensitive Sets the default EventTrak monitoring case sensitivity which is not case default timeout milliseconds Restores the default EventTrak monitoring timeout ex
50. eplies timestamp requests timestamp replies address mask requests address mask replies messages messages discarded errors destination unreachables time exceeded messages parameter problems source quench requests redirects ping requests ping replies timestamp requests timestamp replies address mask requests address mask replies configured as state control configured as state control configured as state control 37 4 Configuration Using XML interface Attribute of instance is ethO generic ethernet Present only for etho arp default gateway network mask domain mac address hostname ip address last change mtu primary dns secondary dns IntelliBox l O 2100 Command Reference status errors speed duplex encapsulation type timeout no link link up disabled unknown error text none 10 100 full half ARPA ARPA 38 4 Configuration Using XML interface transmit Attribute of instance is ethO Continued receive IntelliBox l O 2100 Command Reference octets unicast non unicast discards errors broadcast packets multicast packets filtered packets deferred multiple retries one retry underflows late collisions retry errors carrier lost errors octets unicast non unicast discards errors broadcast packets multicast packets filtered packets unknown protocol framing errors overflows crc errors
51. er gt no client user lt user gt command no host dsa no host rsa no host user lt user gt show show client server lt server gt show client user lt user gt show history Displays the last 20 commands entered during the current CLI session authoriy generate dsa show history Displays the last 20 commands entered during the current CLI session Stores the current configuration in permanent memory clrscrn Clears the screen IntelliBox l O 2100 Command Reference 85 5 Commands and Levels default ical por default remote por ost lt P address gt ocal por lt numbers ie no level remote port lt number gt show history Displays the last 20 commands entered during the current CLI session state disable Disables syslog logging state enable Enables syslog logging write Stores the current configuration in permanent memory activity none Sets the EventTrak task activity to None activity output lt number gt Sets the EventTrak task activity to control the designated output pin activity ping Sets the EventTrak task activity to send a ping once per second clrscrn Clears the screen default activity Sets the default EventTrak task activity which is None efault description Removes the description of an EventTrak control task default output control Sets the default EventTrak output control which is Exclu sive description lt text gt Sets the description of an EventTrak control task It will appear in
52. ersist max entries mode echo serial string serial string signon message wait time state read community write community system contact system name system description system location traps 4 Configuration Using XML enable disable enable disable enable disable state enable disable primary destination secondary destination Default disable Default disable Default 100 Default enable Value is SECRET hidden from user view Default public Value is SECRET hidden from user view Default private Default lt Default gt Default lt Default gt Default enable 28 ssh client ssh command mode ssh server delete known hosts known host delete known host Attribute of instance is required for the known host name delete client users client user Attribute of instance is required for the user name state port max sessions host rsa keys host dsa keys delete authorized users authorized user delete authorized user Attribute of instance is required for the authorized user name IntelliBox l O 2100 Command Reference 4 Configuration Using XML enable disable name public rsa key public dsa key enable disable password remote command public rsa key private rsa key public dsa key private dsa key enable disable public key private key public key private key name password public rsa key public dsa ke
53. evel Changes to the command level for EventTrak Match con figuration Removes the EventTrak monitoring match string Removes the EventTrak wildcard character Turns off RSS tracing of EventTrak string matches Turns on RSS tracing to post each time EventTrak matches the string Displays the current configuration Displays the last 20 commands entered during the current CLI session Sets the EventTrak monitoring match string allowing for binary characters 75 string set lt text gt task lt number gt timeout milliseconds lt number gt wildcard lt text gt write case sensitive no case sensitive yes clrsern default case sensitive default timeout milliseconds exit match lt number gt no string no wildcard rss trace matches disable rss trace matches enable show show history string binary lt binary gt string set lt text gt task lt number gt timeout milliseconds lt number gt wildcard lt text gt write case sensitive no case sensitive yes clrsern default case sensitive default timeout milliseconds exit match lt number gt IntelliBox l O 2100 Command Reference 5 Commands and Levels Sets the EventTrak monitoring match string Changes to the command level for EventTrak Task confi guration Sets the EventTrak monitoring timeout milliseconds Old data that might Sets the EventTrak monitoring wildcard character Where it is placed in the Stores the current c
54. exit Exits to the EventTrak level match lt number gt Changes to the command level for EventTrak Match con figuration no ping address Removes the EventTrak ping address output control exclusive Sets the EventTrak output control to exclusive so if the activity is to output control logical or Sets the EventTrak output control to be Logical Or so it may be combined ping address lt text gt Sets the EventTrak ping address to be used when the activity is to send rss trace ping responses disable Turns off RSS tracing of EventTrak ping responses rss trace ping responses enable Turns on RSS tracing of ping responses received by this EventTrak task rss trace steps disable Turns off RSS tracing of EventTrak task steps rss trace steps enable Turns on RSS tracing of each step taken by an EventTrak task rss trace triggers disable Turns off RSS tracing of EventTrak task triggers rss trace triggers enable Turns on RSS tracing of triggers emitted by this EventTrak task show Displays the current configuration show history Displays the last 20 commands entered during the current IntelliBox l O 2100 Command Reference 86 5 Commands and Levels SL session step lt etter gt Changes to the command level for EventTrak Task Step configuration task lt number gt Changes to the command level for EventTrak Task confi guration write Stores the current configuration in permanent memory activity none Sets the EventTrak
55. formfeed disable Disables the printer from anche to the next page at the end of each formfeed enable Forces the printer to advance to the next page at the end of each print job Ends the current print job on this Ipd line lpd lt line gt Enters the configure Ipd level Removes the end of job string Removes the queue name Removes the start of job string queue name lt tex gt Sets the name of the queue that this Ipd line belongs to Displays the current configuration show history Displays the last 20 commands entered during the current CLI session show Statistics Displays statistics and status information for this Ipd line soj disable Disables sending the start of job string after each print job case sensitive no Sets EventTrak monitoring to be insensitive to case so IntelliBox l O 2100 Command Reference 74 5 Commands and Levels either aor A wil case sensitive yes clrsern default case sensitive default timeout milliseconds exit match lt number gt no string no wildcard rss trace matches disable rss trace matches enable show show history string binary lt binary gt string set lt text gt task lt number gt timeout milliseconds lt number gt wildcard lt text gt write case sensitive no case sensitive yes clrsern default case sensitive default timeout milliseconds exit match lt number gt no string no wildcard rss trace matches disable rss trace matches
56. fundamental building block for the future growth of Machine to Machine M2M networks Evolution supports XML configuration records that make configuring the device server easy for users and administrators XML configuration records are easy to edit with a a standard text editor or an XML editor For a brief overview of XML see Chapter 4 Configuration Using XML It provides rules on basic XML syntax a guide to the specific XML tags used and a guide to using XML configuration records Command Line Interface Making the edge to enterprise vision a reality Evolution OS uses industry standard tools for configuration communication and control For example the Evolution OS uses a command line interface CLI whose syntax is very similar to that used by data center equipment such as routers and hubs For details of the CLI see Chapter 5 Commands and Levels It provides an index of the CLI Command Hierarchy with links to the corresponding command details The CLI provides commands for configuring monitoring and controlling the device server IntelliBox l O 2100 Command Reference 8 3 Command Line Interface This chapter describes accessing the IntelliBox by using Telnet SSH or serial ports to configure the IntelliBox navigating the Command Line Interface CLI typing keyboard shortcuts and moving between the levels It contains the following sections Configuration Using Telnet Configuration Using Serial Ports Na
57. g command mode serial string lt string gt command mode serial string binary lt string gt command mode signon message lt string gt command mode signon message binary lt string gt command mode wait time lt milliseconds gt data bits 7 data bits 8 default baud rate default data bits default flow control default interface default parity efault protocol default stop bits default xoff char default xon char exit flow control hardware flow control none flow control software interface rs232 interface rs485 full duplex interface rs485 half duplex IntelliBox l O 2100 Command Reference Displays the last 20 commands entered during the current CLI session Stores the current configuration in permanent memory Disables user defined serial boot string to be echoed in the CLI Enables user defined serial boot string to be echoed in the CLI Enables user to enter a custom string at boot time to enter command mode Sets a string that can be entered at boot time to enter command mode Sets a binary string that can be entered at boot time to enter command mode Sets an ASCII sign on message that is sent from the seri al port when the Sets a binary sign on message that is sent from the serial port when the Uses hardware RTS CTS flow control on the line Does not provide flow control on the line Uses software xon xoff characters flow control on the line Sets the line interface to RS232 Sets the line interfa
58. ggers rss trace triggers enable Turns on RSS tracing of triggers emitted by this EventTrak task show Displays the current configuration show history Displays the last 20 commands entered during the current CLI session step lt etter gt Changes to the command level for EventTrak Task Step configuration task lt number gt Changes to the command level for EventTrak Task confi guration write Stores the current configuration in permanent memory activity none Sets the EventTrak task activity to None activity output lt number gt Sets the EventTrak task activity to control the designated output pin IntelliBox l O 2100 Command Reference 87 5 Commands and Levels activity ping Sets the EventTrak task activity to send a ping once per second clrscrn Clears the screen default activity Sets the default EventTrak task activity which is None efault description Removes the description of an EventTrak control task default output control Sets the default EventTrak output control which is Exclu sive description lt text gt Sets the description of an EventTrak control task It will appear in exit Exits to the EventTrak level match lt number gt Changes to the command level for EventTrak Match con figuration no ping address Removes the EventTrak ping address output control exclusive Sets the EventTrak output control to exclusive so if the activity is to output control logical or Sets the EventTrak outpu
59. gt lt port gt tftp put ascii lt source file gt lt destination file gt lt host gt tftp put ascii lt source file gt lt destination file gt lt host gt lt port gt IntelliBox l O 2100 Command Reference 64 file gt lt host gt lt port gt touch lt file gt admin password lt string gt admin username lt string gt clear counters clrscrn default admin password default admin username exit no clear counters show show history state disable state enable write clrscrn efault protocol default remote port exit host lt number gt name lt text gt no name no remote address no ssh username protocol ssh protocol telnet remote address lt tfext gt remote port lt number gt show show history ssh username lt text gt write clrscrn default protocol default remote port exit host lt number gt name lt text gt no name IntelliBox l O 2100 Command Reference 5 Commands and Levels Create a file Resets the FTP password to the default PASS Resets the FTP username to the default admin Returns to the config level Unzeros FTP counters Displays the FTP settings and statistics Displays the last 20 commands entered during the current CLI session Disables the FTP server Enables the FTP server Stores the current configuration in permanent memory Clears the screen Restores the default value of the protocol Telnet Sets the remote port used to connect to th
60. haracter for use with software flow control on this line Clears the screen Restores the default duplex setting which is auto Restores the default speed setting which is auto negotiate Displays the last 20 commands entered during the current CLI session Continuously displays Ipd status for the specified line Clears the screen Exits to the enable level 72 kill lt line gt show lt line gt show history banner disable banner enable binary disable binary enable capture disable capture enable clrscrn convert newline disable convert newline enable eoj disable eoj enable eoj text binary lt binary gt eoj text set lt text gt exit formfeed disable formfeed enable ill line lt line gt Ipd lt line gt no eoj text no queue name no soj text queue name lt text gt show show history show statistics soj disable soj enable soj text binary lt binary gt soj text set lt text gt terminal lt line gt terminal network test print lt number of lines gt tunnel lt line gt IntelliBox l O 2100 Command Reference 5 Commands and Levels Kills the current print job on the specified line Displays Ipd status for the specified line Displays the last 20 commands entered during the current CLI session Disables printing banner for all print jobs Only print the banner when a Enables printing banner for all print jobs Treats print job as ascii text Filters out all
61. have name and instance attributes A lt configitem gt element must have one or more lt value gt elements and can have a name attribute A lt value gt element can have only data and can have a name attribute The name attribute identifies a group item or value It is always a quoted string The instance attribute identifies the specific option like the serial port number The instance attribute is always a quoted string IntelliBox l O 2100 Command Reference 14 4 Configuration Using XML Notes The name for each lt configgroup gt specified with the name attribute is the group name listed in the Web Manager XCR groups or with the xcr list CLI command See the IntelliBox l O 2100 User Guide for more information about the Web Manager XCR groups An empty or missing lt value gt element in each present lt configgroup gt clears the setting to its default Quick Tour of XML Syntax Declaration The first line lt xml version 1 0 standalone yes gt is called the XML declaration It is required and indicates the XML version in use normally version 1 0 The remainder of the file consists of nested XML elements some of which have attributes and content Element Start and End Tags An element typically consists of two tags start tag and an end tag that surrounds text and other elements element content The start tag consists of a name surrounded by angle brackets for example lt co
62. host lt ip address gt no host lt ip address gt lt ip address gt no location no name server disable server enable show show history traps disable traps enable write client server lt server gt client server lt server gt lt key gt client user lt user gt lt command gt 5 Commands and Levels Displays the last 20 commands entered during the current CLI session Disables the sending of SNMP trap messages Enables the sending of SNMP trap messages Stores the current configuration in permanent memory Set Client Server RSA or DSA key Set Client Server RSA or DSA key Set Client User command and RSA or DSA keys client user lt user gt lt password gt lt command gt Set Client User with password command and optional RSA or DSA keys client us Set Client User with password command and RSA or er lt user gt lt password gt lt command gt lt public gt lt private gt DSA keys arec exit ost ost lt key gt host lt public gt lt private gt host generate dsa 1024 host generate dsa 512 IntelliBox l O 2100 Command Reference 84 5 Commands and Levels host user lt user gt lt password gt lt public gt Sets Host username password and either a RSA or DSA public key host user lt user gt lt password gt lt public gt lt public gt Sets Host username password and both RSA and DSA public keys no client server lt server gt dsa no client server lt server gt rsa no client user lt us
63. how xsr chem lt number gt clear interfaces counters clear query port counters clear xsr counters clrscrn configure connect connect line lt line gt device disable exit ilesystem kill line lt line gt kill ssh lt session gt kill telnet lt session gt line lt line gt no clear interfaces counters no clear query port counters no clear xsr counters nslookup nslookup lt host gt IntelliBox l O 2100 Command Reference 5 Commands and Levels Does not flush serial data upon closing a tunneling con nection Flushes serial data buffer when a tunneling connection is closed Does not watch the modem control pin to disconnect Watches the modem control pin and disconnects if it is not asserted Disables disconnect after timeout feature for tunneling sessions Displays the current configuration Displays the last 20 commands entered during the current CLI session Disconnects when no data has been received on the line serial port for the Stores the current configuration in permanent memory Kills Telnet session with index from show sessions 62 ping lt host gt ping lt host gt lt count gt ping lt host gt lt count gt lt timeout gt reload reload factory defaults secret xcr dump secret xcr dump lt group list gt secret xcr export lt file gt secret xcr export lt file gt lt group list gt show show history show hosts show ibio2100 show interfaces show ip soc
64. ing the current CLI session Stores the current configuration in permanent memory Disables packing Data is sent to the network when re ceived Sets packing mode to accumulate data and transmit it upon receiving the Sets packing mode to accumulate data and transmit it after a specified Sets the send character for packing mode Displays the current configuration Displays the last 20 commands entered during the current 81 5 Commands and Levels oo session threshold lt bytes gt timeout lt milliseconds gt trailing character lt control gt write clrscrn default packing mode default threshold default timeout exit no send character no trailing character packing mode disable packing mode send character packing mode timeout send character lt control gt show show history threshold lt bytes gt timeout lt milliseconds gt trailing character lt control gt write show history state disable state enable write clrscrn enable exit ping lt host gt ping lt host gt lt count gt ping lt host gt lt count gt lt timeout gt show show history IntelliBox l O 2100 Command Reference Sets the threshold byte count If the queued data reach es this threshold Sets the timeout value for packing mode in milliseconds Sets the trailing character for packing mode Stores the current configuration in permanent memory Disables packing Data is sent to the network when re ce
65. isplays the last 20 commands entered during the current CLI session Clears the screen Requires exclusive control of the output for connect mode connection Exits to the next higher level Requires exclusive control of the output for connect mode connection Does not require exclusive control of the output for con nect mode connection Discontinues enabling any output while the connect mode connection is up Selects an output to enable while the connect mode con nection is up Shows the current configuration Displays the last 20 commands entered during the current CLI session Stores the current configuration in permanent memory Clears the screen Requires exclusive control of the output for accept mode connection Exits to the next higher level Requires exclusive control of the output for accept mode connection Does not require exclusive control of the output for accept mode connection Discontinues enabling any output while the accept mode connection is up Selects an output to enable while the accept mode con nection is up Shows the current configuration Displays the last 20 commands entered during the current CLI session Stores the current configuration in permanent memory 80 clrsern default mode exit mode exclusive control mode logical or no output output lt text gt show show history write clrsern default mode exit mode exclusive control mode logical or
66. it Exits to the EventTrak level match lt number gt Changes to the command level for EventTrak Match con figuration no string Removes the EventTrak monitoring match string ae I IEEE wildcard e e the EventTrak wildcard character rss trace matches rss trace matches disable Turns off RSS Turns off RSS tracing of EventTrak string matches of EventTrak string matches rss trace matches enable Turns on RSS tracing to post each time EventTrak matches the string Displays the current configuration show history Displays the last 20 commands entered during the current CLI session string binary lt binary gt Sets the EventTrak monitoring match string allowing for binary characters string set lt text gt Sets the EventTrak monitoring match string task lt number gt Changes to the command level for EventTrak Task confi guration timeout milliseconds lt number gt Sets the EventTrak monitoring timeout milliseconds Old data that might wildcard lt text gt Sets the EventTrak monitoring wildcard character Where it is placed in the Stores the current configuration in permanent memory case sensitive no Sets EventTrak monitoring to be insensitive to case so IntelliBox l O 2100 Command Reference 77 5 Commands and Levels either aor A wil case sensitive yes clrsern default case sensitive default timeout milliseconds exit match lt number gt no string no wildcard rss trace matches disable rss trace
67. ived Sets packing mode to accumulate data and transmit it upon receiving the Sets packing mode to accumulate data and transmit it after a specified Sets the send character for packing mode Displays the current configuration Displays the last 20 commands entered during the current CLI session Sets the threshold byte count If the queued data reach es this threshold Sets the timeout value for packing mode in milliseconds Sets the trailing character for packing mode Stores the current configuration in permanent memory Clears the screen Returns to the config level Displays statistics and information about the query port Displays the last 20 commands entered during the current CLI session Disables response to 77FE requests Permits response to 77FE requests Stores the current configuration in permanent memory Ping destination n times with x timeout in seconds Show system information Displays the last 20 commands entered during the current CLI session 82 show ibio2100 trace route lt host gt clear rss clrscrn default max entries exit feed disable eed enable max entries lt number gt persist disable persist enable show show history show status write buffer size lt bytes gt clrscrn default buffer size default dtr dtr asserted while connected tr continuously asserted tr unasserted show history write buffer size lt bytes gt clrscrn default buffer size
68. kets show processes show sessions show xsr ssh 5 Commands and Levels Ping destination n times with x timeout in seconds Dump specified XML configuration containing secrets to the console Save XML configuration containing secrets to a file Save specified XML configuration containing secrets to a local file Show system information Displays the last 20 commands entered during the current CLI session ssh lt optClientUsername gt lt host gt Begin SSH session on network ssh lt optClientUsername gt lt host gt lt port gt Begin SSH session on network sl mers he SSL configuration level telnet lt host gt telnet lt host gt lt port gt trace route lt host gt tunnel lt line gt write xcr dump xcr dump lt group list gt xcr export lt file gt xcr export lt file gt lt group list gt xcr import lt file gt xcr import lt file gt lt group list gt xcr list xsr dump xsr dump lt group list gt xsr export lt file gt xsr export lt file gt lt group list gt xsr list clrscrn eventtrak lt number gt exit IntelliBox l O 2100 Command Reference Clears the screen Changes to the command level for EventTrak configura tion Exits to the configuration level 63 match lt number gt show history task lt number gt write clrsern eventtrak lt number gt exit match lt number gt show history task lt number gt write cat lt file gt cd lt direct
69. l lt number gt tftp udp Commands at the login level shown in Figure 3 2 do not affect current configuration settings and are not displayed initially If you type lt gt you will see the login sub commands These commands provide diagnostic and status information only Figure 3 2 Login Level Commands gt clrscrn exit ping lt host gt lt count gt show show ibio2100 IntelliBox l O 2100 Command Reference enable ping lt host gt ping lt host gt lt count gt lt timeout gt show history trace route lt host gt 12 3 Command Line Interface To configure the you must be in the enable level and any of its sub levels Figure 3 3 shows the enable level commands Figure 3 3 Enable Level Commands gt enable lt enable gt auto show interfaces auto show xsr clear interfaces counters clear xsr counters configure connect lin disable filesystem kill line lt line gt kill telnet lt session gt lpd no clear query port counters nslookup ping lt host gt ping lt host gt lt count gt lt timeout gt reload factory defaults secret xcr dump lt group list gt secret xcr export lt file gt lt group list gt show history show ibio2100 show ip sockets show sessions ssh ssh lt optClientUsername gt lt host gt lt port gt telnet lt host gt trace route lt host gt write xcr dump lt group list gt xcr export lt file
70. l encoded form for greater than Table 4 8 XCR Groups arp delete ip address Remove an entry from the ARP table Specify the entry by its IP address arp entry ip address mac address timeout Default 60 seconds IntelliBox l O 2100 Command Reference 20 device email Attribute of instance is a number ethernet Attribute of instance is ethO login password enable level password quit connect line cpu speed short name long name serial number firmware version to cc from reply to subject message file overriding domain server port local port priority trigger input name level speed duplex IntelliBox l O 2100 Command Reference 4 Configuration Using XML amp 60 Random amp 62 urgent high normal low very low xio1 xio2 high low auto 10 100 auto half full Value is SECRET hidden from user view Value is SECRET hidden from user view Accepts text containing control characters for example amp 60 control amp 62 A represents control A Default lt control gt L Read only Read only Multiple addresses may be separated with semicolons Multiple addresses may be separated with semicolons Default 25 Default lt Random gt Default normal Default auto Default auto 21 4 Configuration Using XML event trak match string Attribute of Attribute of instance is wildeard instance is a
71. ling Enables accept mode tunneling when the configured start character Sets the accept tunnel AES decrypt key with up to 16 bytes Sets the accept tunnel AES decrypt key with up to 16 bytes Sets the accept tunnel AES encrypt key with up to 16 bytes Sets the accept tunnel AES encrypt key with up to 16 bytes Forwards tunnels network data in accept mode tunne ling Discards all data coming in from the accept mode tunnel before forwarding Forwards tunnels serial data in accept mode tunneling Discards all data coming in from the serial interface before forwarding Clears the screen Restores the default accept mode as always Restores the default protocol as TCP Restores the default 45 second accept mode TCP keep alive timeout Sets an email profile to use to send an email alert upon establishing Sets an email profile to use to send an email alert upon closing Returns to the tunnel level Characters already in the serial data buffer are retained upon establishing Flushes the serial data buffer upon establishing an accept mode tunneling Discontinues sending email alerts upon establishing an accept mode tunnel Discontinues sending email alerts upon closing an accept mode tunnel Uses the default port number as the local port for accept mode tunneling Disables the accept mode TCP keep alive timeout Enters the next lower level 51 password protocol ssh protocol ssl protocol tcp protocol
72. liseconds Old data that might Sets the EventTrak monitoring wildcard character Where it is placed in the Stores the current configuration in permanent memory Kills modbus connection selected by index from show connections Displays the last 20 commands entered during the current CLI session Displays statistics Disables the Modbus TCP Server Enables the Modbus TCP Server 78 5 Commands and Levels display remote ip disable The incoming RING has nothing following it display remote ip enable The incoming RING is followed by the IP address of the caller echo commands disable Does not echo modem commands echo commands enable Echoes modem commands echo pluses disable Does not echo the characters when entering modem command mode echo pluses enable Echoes the characters when entering modem com mand mode incoming connection manual Wait for an ATA command before answering an incoming network connection no connect string Removes optional CONNECT string information for mod em emulation reassert Asserts tunnel modem status with current configured val ues response type numeric Uses numeric type responses response type text Uses text type responses show Displays the current configuration show history Displays the last 20 commands entered during the current CLI session status Displays tunnel modem status verbose response disable verbose response enable write Does not send Modem Resp
73. lt enable Default 50 Default h t Ar S B Referer i User Agent i Default enable 25 interface Attribute of instance is eth0 ip ip filter IntelliBox l O 2100 Command Reference bootp dhcp ip address default gateway hostname domain dhcp client id primary dns secondary dns multicast time to live delete entries filter delete filter entry 4 Configuration Using XML enable disable enable disable amp 60 None amp 62 amp 60 None amp 62 amp 60 None amp 62 amp 60 None amp 62 enable disable ip address net mask ip address net mask Default disable Default enable Accepts an IP address and mask as either 1 IP address only 192 168 1 1 gets a default mask 2 CIDR 192 168 1 1 24 or 3 Explicit mask 192 168 1 1 255 255 255 0 Accepts in IP address in dotted notation like 192 168 1 1 Set the identity of the client device Accepts in IP address in dotted notation like 192 168 1 1 Accepts in IP address in dotted notation like 192 168 1 1 Default 1 hops If enabled deletes any existing entries before adding filter entry Deletes a specific IP filter entry Deletes a specific IP filter entry If configured is a specific IP address If configured is a specific net mask 26 line Attribute of instance is a number Ipd Attribut
74. matches enable show show history string binary lt binary gt string set lt text gt task lt number gt timeout milliseconds lt number gt wildcard lt text gt write additional port lt number gt clrscrn efault response timeout exit kill connection lt index gt no additional port response timeout lt milliseconds gt show show connections show history show statistics tcp server state disable tcp server state enable clrscrn connect string lt text gt default incoming connection default response type IntelliBox l O 2100 Command Reference Sets EventTrak monitoring to be case sensitive requiring an exact match Clears the screen Sets the default EventTrak monitoring case sensitivity which is not case Restores the default EventTrak monitoring timeout Exits to the EventTrak level Changes to the command level for EventTrak Match con figuration Removes the EventTrak monitoring match string Removes the EventTrak wildcard character Turns off RSS tracing of EventTrak string matches Turns on RSS tracing to post each time EventTrak matches the string Displays the current configuration Displays the last 20 commands entered during the current CLI session Sets the EventTrak monitoring match string allowing for binary characters Sets the EventTrak monitoring match string Changes to the command level for EventTrak Task confi guration Sets the EventTrak monitoring timeout mil
75. nal type echo disable echo enable exit exit connect menu disable exit connect menu enable ine lt line gt login connect menu disable login connect menu enable lpd lt line gt no send break preview connect menu IntelliBox l O 2100 Command Reference 5 Commands and Levels Changes to the command level for EventTrak Task Step configuration Changes to the command level for EventTrak Task confi guration Stores the current configuration in permanent memory Sets the number of packets that must be received before an ACK is forced Does not send TCP RSTs upon connection to unused ports Sends TCP RSTs upon connection to unused ports Sets TCP to send data whenever the window is sufficient ly open for improved Sets TCP to send data in accordance with standards Displays the current configuration Displays the last 20 commands entered during the current CLI session Shows TCP statistics Stores the current configuration in permanent memory Sets how long a break should last when it is being sent to the line Clears the screen Restores the break duration to the default value 500 ms Sets the default terminal type UNKNOWN Disables echoing of characters received on the line back to the line Enables echoing of characters received on the line back to the line Exits to the configuration level On the login connect menu removes the menu item allow ing the user to exit On the login conn
76. nfigrecord gt The end tag consists of the same name surrounded by angle brackets but with a forward slash preceding the name for example lt configrecord gt The element content can also contain other child elements Element Attributes The XML element attributes that are name value pairs included in the start tag after the element name The values must always be quoted using single or double quotes Each attribute name should appear only once in an element Figure 4 2 shows an XML example which consists of a declaration first line nested elements with attributes and content Figure 4 2 XML Example lt xml version 1 0 standalone yes gt lt configrecord gt lt configgroup name serial command mode instance 1 gt lt configitem name mode serial string gt lt value gt disable lt value gt lt configitem gt lt configgroup gt lt configrecord gt The Evolution OS uses the attributes in the following subsections to label the group configuration settings IntelliBox l O 2100 Command Reference 15 4 Configuration Using XML Record Group Item and Value Tags A lt configgroup gt Is a logical grouping of configuration parameters and must contain one or more lt configitem gt elements It must have a name attribute and may have an instance attribute A lt configitem gt is a specific grouping of configuration parameters relevant to its parent group An item
77. nnect level for this tunnel disconnect Enters the disconnect level for this tunnel echo start character disable Disables forwarding tunneling of the start character echo start character enable Enables forwarding tunneling of the start character echo stop character disable Disables forwarding tunneling of the stop character echo stop character enable Enables forwarding tunneling of the stop character ine lt line gt ind lt ine gt modem no clear aggregate counters packing show show history Displays the last 20 commands entered during the current CLI session show statistics show connection statistics stop character lt string gt T accept crs echo start character disable Disables forwarding tunneling of the start character echo start character enable Enables forwarding tunneling of the start character Disables forwarding tunneling of the stop character echo stop character enable Enables forwarding tunneling of the stop character exit ine lt line gt Ipd lt line gt IntelliBox l O 2100 Command Reference 94 modem no clear accept counters no clear aggregate counters no clear all counters no clear connect counters no start character no stop character acking show show history show statistics start character lt string gt stop character lt string gt terminal lt ine gt terminal network tunnel lt line gt write auto show stats clear counters clrscrn exit no clear counter
78. non ascii cha racters and Treats print job as binary Sends data byte for byte to the printer Redirects serial output back to the line Redirects serial output from the line to this CLI session Clears the screen Disables converting single new line and carriage return characters to Enables converting single new line and carriage return characters to Disables the printer from advancing to the next page at the end of each Forces the printer to advance to the next page at the end of each print job Displays the last 20 commands entered during the current CLI session Displays statistics and status information for this Ipd line Disables sending the start of job string after each print job 73 5 Commands and Levels write Str the current configuration in permanent memory banner disable Disables printing banner for all print jobs Only print the banner when a Enables printing banner for all print jobs binary disable Treats print job as ascii text Filters out all non ascii cha racters and binary enable Treats print job as binary Sends data byte for byte to the printer capture disable Redirects serial output back to the line capture enable Redirects serial output from the line to this CLI session Clears the screen convert newline disable Disables converting single new line and carriage return characters to convert newline enable Enables converting single new line and carriage return characters to
79. number gt Changes to the command level for EventTrak Task confi guration write Stores the current configuration in permanent memory activity none Sets the EventTrak task activity to None activity output lt number gt Sets the EventTrak task activity to control the designated output pin activity ping Sets the EventTrak task activity to send a ping once per second clrscrn Clears the screen default activity Sets the default EventTrak task activity which is None efault description Removes the description of an EventTrak control task default output control Sets the default EventTrak output control which is Exclu sive description lt text gt Sets the description of an EventTrak control task It will appear in exit Exits to the EventTrak level match lt number gt Changes to the command level for EventTrak Match con figuration no ping address Removes the EventTrak ping address output control exclusive Sets the EventTrak output control to exclusive so if the activity is to output control logical or Sets the EventTrak output control to be Logical Or so it may be combined ping address lt text gt Sets the EventTrak ping address to be used when the activity is to send rss trace ping responses disable Turns off RSS tracing of EventTrak ping responses rss trace ping responses enable Turns on RSS tracing of ping responses received by this IntelliBox l O 2100 Command Reference 89 5 Commands and Levels Event
80. octets from network connect connection time accept connection time connect dns address changes connect dns address invalids local ip address local port remote ip address remote port uptime octets from serial octets from network connect dns address changes connect dns address invalids local ip address local port remote ip address remote port uptime octets from serial octets from network 46 4 Configuration Using XML tunnel modem within group echo commands enable stunner disable verbose response enable disable response type text numeric error unknown commands disable enable incoming connection disabled automatic manual udp in unknown ports in datagrams in errors out datagrams xsr out bytes lines elements errors IntelliBox l O 2100 Command Reference 47 5 Commands and Levels Click the level in the tree structure and it will take you to the command list for that level root e enable enable e chem 1 chem 1 chem 2 chem 2 chem 3 chem 3 chem 4 chem 4 configure config e arp config arp e cli config cli e eventtrak 1 config eventtrak 1 e match 1 config eventtrak match 1 1 match 2 config eventtrak match 1 2 match 3 config eventtrak match 1 3 task 1 config eventtrak task 1 1 task 2 config eventtrak task 1 2 e task 3 config eventtrak task 1 3 e eventtrak 2 config eventtrak 2 e match 1 config eventtrak match 2 1 e match 2 config eventtrak
81. og show statistics subject lt string gt to lt email addresses gt trigger lt xio1 xio2 gt lt high low gt write clear ssh counters clear telnet counters clrscrn default quit connect line enable level password exit login password no clear ssh counters no clear telnet counters quit connect line lt string gt show history show ssh show telnet ssh disable ssh enable ssh max sessions lt number gt ssh port lt number gt telnet disable telnet enable telnet max sessions lt number gt telnet port lt number gt write clear host lt host gt clrsern IntelliBox l O 2100 Command Reference 5 Commands and Levels Displays the last 20 commands entered during the current CLI session Specifies input name and voltage level to trigger sending an email Stores the current configuration in permanent memory Sets the SSH counters to zero Sets the Telnet counters to zero Clears the screen Restores the default string used to quit the connect line command Sets or removes the enable level password by challenging and prompting Exits to the configuration level Sets or removes the CLI login password by challenging and prompting Restores the IP SSH counters to the aggregate values Restores the IP Telnet counters to the aggregate values Sets the string used to quit the connect line command Displays the last 20 commands entered during the current CLI session Sets the m
82. omain name that will be used when connecting to an SMTP server to 54 priority high priority low priority normal priority urgent priority very low replyto lt email address gt send server port lt number gt show show history show log show statistics subject lt string gt to lt email addresses gt trigger lt xio1 xio2 gt lt high low gt write auto show statistics cc lt email addresses gt chem lt number gt clear log clear mail counters clrscrn exit file lt file gt from lt email address gt ocal port lt number gt ocal port random no cc no clear mail counters no file no from no overriding domain no replyto no subject no to no trigger overriding domain lt domain gt priority high priority low priority normal priority urgent IntelliBox l O 2100 Command Reference 5 Commands and Levels Displays the last 20 commands entered during the current CLI session Specifies input name and voltage level to trigger sending an email Stores the current configuration in permanent memory Specifies a text file the contents of which will be the mes sage body Sets local port used to send email alerts to random Removes the file name so the message body will be empty Sets a domain name that will be used when connecting to an SMTP server to 55 priority very low replyto lt email address gt send server port lt number gt show show history show l
83. onfiguration in permanent memory Sets EventTrak monitoring to be insensitive to case so either a or A will Sets EventTrak monitoring to be case sensitive requiring an exact match Clears the screen Sets the default EventTrak monitoring case sensitivity which is not case Restores the default EventTrak monitoring timeout Exits to the EventTrak level Changes to the command level for EventTrak Match con figuration Removes the EventTrak monitoring match string Removes the EventTrak wildcard character Turns off RSS tracing of EventTrak string matches Turns on RSS tracing to post each time EventTrak matches the string Displays the current configuration Displays the last 20 commands entered during the current CLI session Sets the EventTrak monitoring match string allowing for binary characters Sets the EventTrak monitoring match string Changes to the command level for EventTrak Task confi guration Sets the EventTrak monitoring timeout milliseconds Old data that might Sets the EventTrak monitoring wildcard character Where it is placed in the Stores the current configuration in permanent memory Sets EventTrak monitoring to be insensitive to case so either a or A will Sets EventTrak monitoring to be case sensitive requiring an exact match Clears the screen Sets the default EventTrak monitoring case sensitivity which is not case Restores the default EventTrak monitoring timeout Exits to the Ev
84. onse Codes Sends Modem Response Codes out on the Serial Line Stores the current configuration in permanent memory cls connect string lt text gt default incoming connection default response type display remote ip disable display remote ip enable The incoming RING is followed by the IP address of the caller echo commands disable Does not echo modem commands echo commands enable Echoes modem commands echo pluses disable Does not echo the characters when entering modem command mode echo pluses enable Echoes the characters when entering modem com mand mode IntelliBox l O 2100 Command Reference 79 incoming connection manual no connect string reassert response type numeric response type text show show history status verbose response disable verbose response enable write clrsern default mode exit mode exclusive control mode logical or no output output lt text gt show show history write clrsern default mode exit mode exclusive control mode logical or no output output lt text gt show show history write IntelliBox l O 2100 Command Reference 5 Commands and Levels Wait for an ATA command before answering an incoming network connection Removes optional CONNECT string information for mod em emulation Asserts tunnel modem status with current configured val ues Uses numeric type responses Uses text type responses Displays the current configuration D
85. ory gt clrscrn compact cp lt source file gt lt destination file gt dump lt file gt Is lt directory gt mkdir lt directory gt mv lt source file gt lt destination file gt pwd rm lt file gt rmdir lt directory gt show show history show tree 5 Commands and Levels Changes to the command level for EventTrak Match con figuration Displays the last 20 commands entered during the current CLI session Changes to the command level for EventTrak Task confi guration Stores the current configuration in permanent memory Clears the screen Changes to the command level for EventTrak configura tion Exits to the configuration level Changes to the command level for EventTrak Match con figuration Displays the last 20 commands entered during the current CLI session Changes to the command level for EventTrak Task confi guration Stores the current configuration in permanent memory Displays the last 20 commands entered during the current CLI session Show all files and directories from current directory tftp get ascii lt source file gt lt destination file gt lt host gt Get an ascii file using TFTP tftp get ascii lt source file gt lt destination file gt lt host gt lt port gt Get an ascii file using TFTP tftp get binary lt source file gt lt destination file gt lt host gt Get a binary file using TFTP tftp get binary lt source file gt lt destination file gt lt host
86. ou will be pasting an XCR you do not need to include passwords in the file because you are already logged into the device However if you send an XCR to one or more devices that are password protected you can include the appropriate passwords in the XCR and skip the login steps IntelliBox l O 2100 Command Reference 19 4 Configuration Using XML The xml paste passwords lt configgroup gt name is used with the passwords lt configitem gt name and cli login and cli enable level values to specify the passwords to use when the device has been configured with password protection The password value is clear text To protect the password establish an SSH connection to the device server Figure 4 7 shows an example Figure 4 7 XML Example of Supplying Passwords lt To supply passwords when importing via cli capture gt lt configgroup name xml paste passwords gt lt configitem name passwords gt lt value name cli login gt lt value gt lt value name cli enable level gt lt value gt lt configitem gt lt configgroup gt XML Configuration Groups Table 4 8 lists the Intellibox XCR groups in alphabetical order This table indicates the various group items as well as some possible value names and options Note Any instance of amp 60 in the table may be read as lt the html encoded form for less than and any instance of amp 62 may be read as gt the htm
87. protocol with AES encryption for connect mode tunneling Uses Telnet protocol with IAC for connect mode tunne ling Uses UDP protocol for connect mode tunneling 58 protocol udp aes reconnect time lt milliseconds gt remote address lt text gt remote port lt number gt show show history show status ssh username lt text gt tcp keep alive lt milliseconds gt write aes decrypt key lt hexadecimal gt aes decrypt key text lt text gt aes encrypt key lt hexadecimal gt aes encrypt key text lt text gt block network disable block network enable block serial disable block serial enable clrsern connect mode always connect mode any character connect mode disable connect mode modem control asserted connect mode modem emulation connect mode start character default connect mode default local port default protocol default reconnect time default tcp keep alive IntelliBox l O 2100 Command Reference 5 Commands and Levels Uses UDP protocol with AES encryption for connect mode tunneling Sets the reconnect time value for tunneling connections established by the Sets the remote host to establish tunneling connections with Sets the remote port to use for connect mode tunneling Displays the current configuration Displays the last 20 commands entered during the current CLI session Displays tunnel connect status Sets the SSH user name for use when establishing tunne ling conne
88. ption for connect mode tunneling Uses Telnet protocol with IAC for connect mode tunne ling Uses UDP protocol for connect mode tunneling Uses UDP protocol with AES encryption for connect mode tunneling Sets the reconnect time value for tunneling connections established by the Sets the remote host to establish tunneling connections with Sets the remote port to use for connect mode tunneling Displays the current configuration Displays the last 20 commands entered during the current CLI session Displays tunnel connect status Sets the SSH user name for use when establishing tunne ling connections Enables TCP keep alive for connect mode tunneling and sets the timer Stores the current configuration in permanent memory 60 auto show tlog auto show upload clrscrn cpu speed lt mhz gt efault cpu speed default long name default short name exit long name lt name gt short name lt name gt show show buffer pool show codefile memory show delta memory show hardware information show history show ibio2100 show linereference memory lt code filename gt show memory show task memory show task state show tlog show upload write character stop disable character stop enable clrscrn exit flush serial disable flush serial enable modem control disable modem control enable no timeout show show history timeout lt milliseconds gt write IntelliBox l O 2100 Command R
89. s Sets the default terminal type UNKNOWN Disables echoing of characters received on the line back to the line Enables echoing of characters received on the line back to the line Exits to the configuration level On the login connect menu removes the menu item allow ing the user to exit On the login connect menu inserts the menu item allow ing the user to exit Enters the line level Disables the login connect menu so a user will get the CLI immediately Enables the login connect menu so a user will get the menu rather than the Enters the configure Ipd level Removes the configured send break character Shows the layout of the connect menu with current set tings Sets the optional send break character Displays the current configuration Displays the last 20 commands entered during the current CLI session Sets how long a break should last when it is being sent to the line Clears the screen Restores the break duration to the default value 500 ms Sets the default terminal type UNKNOWN 92 echo disable echo enable exit exit connect menu disable exit connect menu enable line lt line gt login connect menu disable login connect menu enable lpd lt line gt no send break preview connect menu send break lt control gt show show history terminal lt line gt terminal network terminal type lt text gt tunnel lt line gt write allow file creation disable
90. s show history show stats write IntelliBox l O 2100 Command Reference 5 Commands and Levels Displays the last 20 commands entered during the current CLI session Displays the last 20 commands entered during the current CLI session Shows UDP statistics Stores the current configuration in permanent memory 95
91. s HTTP server logging Enables HTTP server logging Sets the log format string for the HTTP server using the following Sets the maximum number of bytes the HTTP server ac 66 5 Commands and Levels oo oeps when receiving max timeout lt seconds gt no clear counters port lt number gt server disable server enable show show auth show history show log show statistics ssl port lt number gt ssl3 disable ssl3 enable tls1 0 disable tls1 0 enable tls1 1 disable tls1 1 enable write auto show stats clear counters clrscrn exit no clear counters show show history show stats state disable state enable write ootp disable bootp enable clear host lt string gt clrscrn default gateway lt P address gt dhcp client id binary lt binary gt hcp client id set lt text gt dhcp disable dhcp enable hcp renew domain lt text gt IntelliBox l O 2100 Command Reference receiving a request Displays the last 20 commands entered during the current CLI session Continuously shows ICMP statistics Displays the last 20 commands entered during the current CLI session Sets the configurable gateway IP address to the default value 67 5 Commands and Levels Exits to the config level hostname lt text gt ip address lt ip address cidr gt ink no default gateway no dhcp client id no domain no hostname no ip address no primary dns no secondary dns primary dns lt P a
92. ssh server lt configitem name host rsa keys gt lt value name public key gt lt value gt lt value name private key gt lt value gt lt configitem gt lt configgroup gt IntelliBox l O 2100 Command Reference 16 4 Configuration Using XML Figure 4 5 XML Example of Multiple Items lt xml version 1 lt va lt configgroup name email lt configitem name lue gt john doe somewhere com gt lt value gt lt configitem gt lt configitem name 0 standalone yes gt instance 1 gt to gt w from gt lt va lt configgroup gt lue gt evolution intellibox com gt lt value gt lt configitem gt Figure 4 6 XML Example with Multiple Groups lt xml version 1 0 standalone yes gt lt configgroup name ftp server gt lt configitem name state gt lt value gt enable lt value gt lt configitem gt lt configitem name admin username gt lt value gt admin lt value gt lt configitem gt lt configitem name admin password gt lt value gt lt configured and ignored gt lt value gt lt configitem gt lt configgroup gt lt configgroup name tftp server gt lt configitem name state gt lt value gt enable lt value gt lt configitem gt lt configitem name allow file creation gt lt value gt disable lt value gt lt configitem gt
93. t control to be Logical Or so it may be combined ping address lt text gt Sets the EventTrak ping address to be used when the activity is to send rss trace ping responses disable Turns off RSS tracing of EventTrak ping responses rss trace ping responses enable Turns on RSS tracing of ping responses received by this EventTrak task rss trace steps disable Turns off RSS tracing of EventTrak task steps rss trace steps enable Turns on RSS tracing of each step taken by an EventTrak task rss trace triggers disable Turns off RSS tracing of EventTrak task triggers rss trace triggers enable Turns on RSS tracing of triggers emitted by this EventTrak task show Displays the current configuration show history Displays the last 20 commands entered during the current CLI session step lt etter gt Changes to the command level for EventTrak Task Step configuration task lt number gt Changes to the command level for EventTrak Task confi guration write Stores the current configuration in permanent memory activity none Sets the EventTrak task activity to None activity output lt number gt Sets the EventTrak task activity to control the designated output pin activity ping Sets the EventTrak task activity to send a ping once per second clrscrn Clears the screen default activity Sets the default EventTrak task activity which is None efault description Removes the description of an EventTrak control task default output
94. task activity to None activity output lt number gt Sets the EventTrak task activity to control the designated output pin activity ping Sets the EventTrak task activity to send a ping once per second clrscrn Clears the screen default activity Sets the default EventTrak task activity which is None efault description Removes the description of an EventTrak control task default output control Sets the default EventTrak output control which is Exclu sive description lt text gt Sets the description of an EventTrak control task It will appear in exit Exits to the EventTrak level match lt number gt Changes to the command level for EventTrak Match con figuration no ping address Removes the EventTrak ping address output control exclusive Sets the EventTrak output control to exclusive so if the activity is to output control logical or Sets the EventTrak output control to be Logical Or so it may be combined ping address lt text gt Sets the EventTrak ping address to be used when the activity is to send rss trace ping responses disable Turns off RSS tracing of EventTrak ping responses rss trace ping responses enable Turns on RSS tracing of ping responses received by this EventTrak task rss trace steps disable Turns off RSS tracing of EventTrak task steps rss trace steps enable Turns on RSS tracing of each step taken by an EventTrak task rss trace triggers disable Turns off RSS tracing of EventTrak task tri
95. the lt tab gt key displays the first command that begins with those characters Hitting the lt tab gt key again displays the next command that begins with the original characters typed You can press lt Enter gt to execute the command or you can backspace to edit any parameters The following key combinations are allowed when configuring the device server using the CLI Ctrl a place cursor at the beginning of a line Ctrl b backspace one character Ctrl d delete one character Ctrl e place cursor at the end of the line Ctrl f move cursor forward one character Ctrl k delete from the current position to the end of the line Ctrl I redraw the command line Ctrl n display the next line in the history Ctrl p display the previous line in the history Ctrl u delete entire line and place cursor at start of prompt Ctrl w delete one word back Ctrl z a shortcut for the exit command Esc b move cursor back one word gt gt gt FF o Esc f move cursor forward one word Understanding the CLI Level Hierarchy The CLI hierarchy is a series of levels Arranging commands in a hierarchy of levels provides a way to organize and group similar commands provide different levels of security and reduce the complexity and number commands and options presented to a user at one time When you start a command line session you begin at the login level This level can be password prote
96. tions Enables RSS Trace of accept mode connections Displays the current configuration Displays the last 20 commands entered during the current CLI session Displays tunnel accept status Enables TCP keep alive for accept mode tunneling and sets the timer Stores the current configuration in permanent memory 50 accept mode always accept mode any character accept mode disable accept mode modem control asserted accept mode modem emulation accept mode start character aes decrypt key lt hexadecimal gt aes decrypt key text lt text gt aes encrypt key lt hexadecimal gt aes encrypt key text lt text gt block network disable block network enable block serial disable block serial enable clrscrn default accept mode default protocol default tcp keep alive email connect lt number gt email disconnect lt number gt exit flush serial disable flush serial enable kill connection ocal port lt number gt no aes decrypt key no aes encrypt key no email connect no email disconnect no local port no tcp keep alive output select IntelliBox l O 2100 Command Reference 5 Commands and Levels Enables the tunneling server to always accept tunneling connections Enables the tunneling server to accept tunneling connec tions only when a Disables accept mode tunneling Enables the tunneling server to accept tunneling connec tions when the modem Enables modem emulation for accept mode tunne
97. tions information or references to material not covered in the publication Caution Means you might do something that could result in faulty equipment operation or loss of data CLI terminal sessions and examples of CLI input IntelliBox l O 2100 Command Reference 6 Additional Documentation 1 About This Guide Visit the Lantronix web site at www lantronix com support documentation for the latest documentation and the following additional documentation IntelliBox I O 2100 User Guide Devicelnstaller Online Help Secure Com Port Redirector User Guide Com Port Redirector Quick Start and Online Help IntelliBox l O 2100 Command Reference Information about the IntelliBox hardware testing the IntelliBox and integrating the IntelliBox device into your product Instructions for using the Lantronix Windows based utility to locate the IntelliBox and to view its current settings Instructions for using the Lantronix Windows based utility to create secure virtual com ports Instructions for using the Lantronix Windows based utility to create virtual com ports 2 Overview Evolution OS is the Lantronix cutting edge operating system that supports three convenient configuration methods Web Manager Command Line Interface CLI and Extensible Markup Language XML For more information about the Web Manager see the ntelliBox l O 2100 User Guide at the Lantronix website XML Architecture and Device Control XML is a
98. tware flow control on this line 70 5 Commands and Levels command mode echo serial string disable Disables user defined serial boot string to be echoed in the CLI command mode echo serial string enable Enables user defined serial boot string to be echoed in the CLI command mode serial string Enables user to enter a custom string at boot time to enter command mode command mode serial string lt string gt Sets a string that can be entered at boot time to enter command mode command mode serial string binary lt string gt Sets a binary string that can be entered at boot time to enter command mode command mode signon message lt string gt Sets an ASCII sign on message that is sent from the seri al port when the command mode signon message binary lt string gt Sets a binary sign on message that is sent from the serial port when the command mode wait time lt milliseconds gt Sets boot up wait time for command mode serial string data bits 7 data bits 8 default baud rate default data bits default flow control default interface default parity default protocol default stop bits default xoff char default xon char exit flow control hardware flow control none flow control software interface rs232 interface rs485 full duplex interface rs485 half duplex ine lt line gt Ipd lt line gt name lt text gt no clear line counters no command mode no command mode serial string no command mode signon mess
99. ute of instance is a number IntelliBox l O 2100 Command Reference connect mode remote address remote port local port protocol ssh username tcp keep alive aes encrypt key aes decrypt key reconnect time flush serial block serial block network email connect email disconnect output select stop character modem control timeout flush serial output mode 4 Configuration Using XML disable always any character start character modem control asserted modem emulation amp 60 Random amp 62 tcp udp ssh telnet tcp aes udp aes ssl amp 60 None amp 62 enable disable enable disable enable disable amp 60 None amp 62 amp 60 None amp 62 logical or exclusive control enable disable enable disable Default disable Default lt Random gt Default tcp Username must correspond to a configured ssh client user Default 45000 milliseconds Value is SECRET hidden from user view Value is SECRET hidden from user view Default 15000 milliseconds Default disable Default disable Default disable Default lt None gt Default lt None gt Accepts a control character for example amp 60 control amp 62 A represents control A Default disable Default 0 milliseconds Default disable 32 tunnel modem Attribute of instance is a number tunnel packing Attribute of instanc
100. vigating the CLI Hierarchy Using Keyboard Shortcuts and CLI Understanding the CLI Level Hierarchy Refer to Chapter 5 Commands and Levels for a complete list of levels commands and descriptions Configuration Using Telnet To access and configure the device server by using a Telnet session over the network you must first establish a Telnet connection You can also establish a Telnet connection by clicking the Telnet Configuration tab in Devicelnstaller See the Devicelnstaller Online Help for more information available on our website www lantronix com support downloads To access the IntelliBox by using Telnet perform the following steps 1 Click Start gt Run The Run dialog box displays 2 Type cmd in the dialog box and press OK 3 Type telnet x x x x x x x x is the IP address The IntelliBox is online when the command prompt gt displays You are at the root level of the CLI Note Depending on the level of security a password may be required Configuration Using Serial Ports Serial Command Mode The serial port can be configured to operate in command mode permanently or to be triggered under specified conditions See the line lt line gt Level command description for more information Serial Recovery In this mode the normal boot process is interrupted allowing recovery from unknown or incorrect configuration settings While the back door is active the CLI prompt is changed to gt gt inste
101. y If enabled deletes any existing hosts before adding known host Specify the known host to delete If enabled deletes any existing client users before adding client user 29 syslog tcp telnet command mode IntelliBox l O 2100 Command Reference RSA certificate DSA certificate delete all cas state host local port remote port severity log level resets ack limit send data state port max sessions 4 Configuration Using XML enable disable enable disable none emergency alert critical error warning notice information debug enable disable standard expedited enable disable Enter the text of the certificate Enter the text of the private key If configured and not exporting secrets exports only a placeholder Enter the text of the certificate Enter the text of the private key If configured and not exporting secrets exports only a placeholder If enabled deletes any existing trusted cas before adding trusted ca Default disable Default 514 Default 514 Default none Default enable Number of packets received before an ACK is forced Default 3 packets Default standard Default enable Default 23 Default 3 30 terminal Attribute of instance is either network or a number tftp server tunnel accept Attribute of instance is a number IntelliBox l O 210

Lantronix Network Hardware 2100 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents