Land Pride FDR2572 User's Manual
Contents
1. loose bolts and pins Be sure all nuts and bolts are tight Especially make sure mower blades bolts and nuts are tight Section 1 Page 1 Be certain all guards and shields are in place and in good condition Section 5 Page 20 Lubricate the mower as needed Refer to Maintenance and Lubrication 3 Carefully raise and lower the implement to ensure that the drawbar tires and other equipment on the tractor do not contact the frame or PTO driveline 4 With the PTO disengaged and completely stopped check the mower blades for sharpness See Service Mowing Blades on page 17 IMPORTANT Do not exceed rated PTO speed of mower Excessive engine speed will cause damage to the power train components IMPORTANT Stop PTO rotation immediately if vibration occurs during operation Wait for mower to come to a complete stop Follow all tractor shut down procedures before dismounting from the tractor to check for probable causes 5 Set tractor throttle to idle or slightly above idle and slowly engage the PTO Once the Grooming Mower is running smoothly increase tractor PTO speed to 540 rpm PTO speed Stop PTO rotation immediately if vibration occurs at any time Wait for the PTO to come to acomplete stop and then dismount from the tractor to check for probable causes Transporting A CAUTION When traveling on public roads whether at night or during the day use acce2. 818 130C Caution E 818 230C Red Reflector Both Sides A DANGER GUARD MISSING DO NOT OPERATE A DANGER 818 540C Danger Guard Missing GUARD MISSING DO NOT OPERATE A DANGER 4 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Table of Contents Important Safety Information ai Vi eID Va It GUARD MISS When this is visib DO NOT OPERAT ENTANGLEMENT HAZARD can couse Serious Injury or Death Si no entiende ingles se prefiere que busque a alquien que interprete las instrucciones para usted SEE a J 818 543C Danger Guard Missing ADANGER 818 552C ROTATING DRIVELINE CONTACT CAN CAUSE DEATH Danger Rotating Driveline KEEP AWAY DO NOT OPERATE WITHOUT e All driveline guards tractor and equipment shields in place Drivelines securely attached at both ends e Driveline guards that turn freely on Driveline 818 5520 To prevent serious injury or death 818 558C Warning General ngles pida a ea para que le tr de seguridad 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 5 Table of Contents Important Safety Information Land Pride Q A DANGER gt E a Ears ROTATING BLADES KEEP AWAY To prevent serious injury or death from rotating blade contact Never allow rid
3. _ wala ONYT _ _ i Le ZININN ZININNS Transport Machinery Safely A Comply with state and local laws A Maximum transport speed for implement is 20 mph DO NOT EXCEED Never travel at a speed which does not allow adequate control of steering and stopping Some rough terrain require a slower speed A Sudden braking can cause a towed load to swerve and upset Reduce speed if towed load is not equipped with brakes A Use the following maximum speed tow load weight ratios as a guideline 20 mph when weight is less than or equal to the weight of tractor 10 mph when weight is double the weight of tractor A IMPORTANT Do not tow a load that is more than double the weight of tractor x mM f ror y Practice Safe Maintenance A Understand procedure before doing work Use proper tools and equipment refer to Operator s Manual for additional information A Work in a clean dry area A Lower the implement to the ground put tractor in park turn off engine and remove key before performing maintenance A Allow implement to cool completely A Do not grease or oil implement while it is in operation A Inspect all parts Make sure parts are in good condition amp installed properly A Remove buildup of grease oil or debris A Remove all tools and unused parts from implement before operation ne Tractors With Cabs Tractors Equipped With ROPS A There
4. Level mower Sharpen blades amp balance or replace Tractor loaded down by mower Mow at full throttle 540 PTO rpm Shift to a lower gear Clean mower 24 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Table of Contents Section 8 Appendix Torque Values Chart for Common Bolt Sizes Bolt Head Identification Bolt Head Identification Bolt Size Bolt Size Inches Grade 2 Grade 5 Grade 8 Metric Class 5 8 Class 8 8 Class 10 9 in tpi N ft Ib N ml ft lb N m ft lb mmx N ml ft Ib N m ft Ib Nr m N ml tto Ib 1 4 20 74 56 11 8 he 12 M5X0 8 4 3 jv4 28 ja5 6 Mexi f 5 516 18 h5 11 17 M8x1 25 17 12 5 16 24 17 13 9 IMsx1 l8 13 3 8 16 27 20 M1i0xX1 5 33 24 lsa 24 31 22 A C M10x0 75 39 29 7 16 14 43 32 M12 X 1 75 58 42 z16 20 49 36 M12x1 5 60 44 1 2 13 l66 49 M12 X1 o0 66 1 2 20 75 55 M14 x 2 o2 68 loie 12 95 70 150 110 M14xX1 5 99 73 loie 18 105 79 165 120 M16 X 2 145 105 5 8 11 1130 97 IM16X1 5 155 115 5 8 18 11450 110 IMi8x2 5 195 145 13 4 10 235 170 M18 x1 5 220 165 3 4 16 260 190 M20x2 5 280 205 7 8 9 225 165 M20x1 5 310 230 7 8 14 250 185 M24 X 3 480 355 j1 8 340 250 M24 X 2 525 390 j1 12 370 275 M30 x3 5 960 705 1510 1120 2100 1550 1 1 8 7 480 355 M30 x 2 1060 785 1680 1240 2320 171
5. bottom as shown Secure with existing 1 2 whiz nuts 10 Tighten nuts to 76 ft lbs of torque Assemble brackets 2 and 3 to deck with carriage bolts 4 and flange nuts 5 Insert roller 8 between brackets and install pin 1 through brackets and roller Secure with washer 6 and cotter pin 7 17713 NO Front Roller Assembly Figure 1 3 Tractor Hook Up Be certain that tractor draw bar will not interfere Move draw bar ahead or remove if required Draw bar should also be checked for clearance when unit is being raised for the first time Align lower link arms of tractor to hitch clevises on mower Insert lower hitch pins into lower ball swivels and attach linch pins Attach tractor top link to upper floating hitch on mower with pin supplied Secure with lock pin Adjust the tractor top link in or out to place the upper hitch pin vertically above the lower hitch pins as shown in Figure 1 4 to allow mower flotation Tractor Hook Up Figure 1 4 10 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Table of Contents Section 1 Assembly and Set Up Driveline Installation An additional driveline may be required if the Grooming Mower is used on more than one tractor especially if a quick hitch is used IMPORTANT It is necessary to aligning the tractor s PTO shaft level with the Grooming Mower s gearbox shaft when checking driveline minimum len
6. options 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 15 Table of Contents Section 3 Adjustments Leveling the Mower NOTE Tractor and mower should be on level Set lower hitches and upper floating hitch as shown below in Figure 3 1 _ 2 Start tractor and raise mower watching that tractor draw bar if not removed does not interfere with mower 3 Slowly lower the mower until gauge wheels touch the ground and the lower mower 3 point hitch bars are parallel to the ground in floating position Set tractor 3 point stop 4 Setpark brake and turn off tractor Remove key from ignition 5 Rotate blades parallel to direction of travel 6 Measure the clearance from the cutting edge to the ground at front and rear of the blade This measurement should be equal or have the blade at the front of the mower not more than 1 2 lower than the blade at the rear of the mower 17366 Ib HA 3 Point Hitch Figure 3 1 Cutting Height Adjustment 1 Using the tractor raise the mower off the ground and support under it with secure blocking so not to let the mower drift down during maintenance 2 Holding wheel and yoke assembly up remove quick lock pin from top of gauge wheel spindle Position full length spacers and half spacer as required All spacers on top of spindle tube allows for approximately 3 4 cutting height Adjustments range from 3 4 to a maximum of 5 1 4 i
7. read your Grooming Mower Operator s Manual properly attached your Land Pride FDR25 to your tractor and reviewed the operating checklist You should have also inspected the area where you intend to mow and cleared it of safety hazards and foreign objects If you have not yet completed all of these functions itis an absolute must that you do so now before proceeding Now that you are properly briefed and prepared its time to start the tractor and move to your starting point When transporting to your mowing site select a safe ground transport speed When traveling on roadways transport in such a manner that faster moving vehicles can easily see you and pass you safely When traveling over rough and hilly terrain reduce your speed avoid quick or sharp steering corrections Take extra care to insure that the mower doesn t come into contact with obstacles such as trees buildings or fences When you have arrived at the mowing site start the tractor raise the deck to make sure that everything is properly attached and that the driveline is not in a bind or in contact with the mounting frame Also make sure the tractor tires aren t in contact with the deck With the deck still in the raised position proceed to your starting point and lower your deck to the ground in mowing position Reduce your tractor engine rpm to idle and engage the PTO Gradually raise the tractor engine rpm to achieve the 540 rpm PTO speed Now begin mowing at a gr
8. shield at mark X dimension Cut same amount off inner shaft X1 dimension Repeat cut off procedure Y amp Y1 dimensions to cut outer driveline half f Remove all burrs and cuttings Apply multi purpose grease to the inside of the outer driveline profile and reassemble the two profiles Attach inner driveline yoke to gearbox shaft and outer driveline yoke to tractor s PTO shaft The driveline should now be moved back and forth to insure that both ends are secured to the PTO shafts Reattach any end that is loose IMPORTANT The two supplied safety chains must be attached to outer and inner driveline yoke shields and to the mower deck and tractor to keep driveline 8 shields from rotating Hook one driveline safety chain in the hole on the outer driveline yoke shield and the opposite end to the tractor Hook the second driveline safety chain in the hole on the inner driveline yoke shield and the opposite end to the mower 10 Start tractor and raise mower just enough to remove 11 support blocks used in step 4a on page 11 Slowly engage tractor s 3 point controls to lower mower Check for sufficient drawbar clearance Move drawbar ahead aside or remove if required 12 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Section 2 Operating Instructions Table of Contents Tractor Shut Down Procedure It is essential that the tractor be shu
9. the full attention of the operator Avoid wearing radio headphones while operating Nak OD A Keep Riders Off Machinery A Riders obstruct the operator s view they could be struck by foreign objects or thrown from the machine A Never allow children to operate equipment 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M Table of Contents Land Pride Important Safety Information Safety Labels by Land Pride When ordering new components make sure the correct safety labels are included in the request Your Grooming Mower comes equipped with all safety labels in 4 Refer to this section for proper label placement place They were designed to help you safely operate your To install new labels implement Read and follow their directions a Clean the area the label is to be placed 1 Keep all safety labels clean and legible b Spray soapy water on the surface where the label is to 2 Replace all damaged or missing labels To order new labels be placed go to your nearest Land Pride dealer or visit our dealer locator at landpride com 3 Some new equipment installed during repair requires safety labels to be affixed to the replaced component as specified c Peel backing from label Press firmly onto the surface Squeeze out air bubbles with the edge of a credit card ACAUTION To avoid Injury or Machine Damage Operate only wit 240 rpm PIO 818 1300 Rev B
10. 0 1 1 8 12 540 395 1210 890 1960 1440 M36 X 3 5 1730 1270 2650 1950 3660 2700 l1 1 4 7 680 500 1520 1120 2460 1820 M36 X 2 1880 1380 2960 2190 4100 3220 1 1 4 12 750 555 i6so 1240 2730 2010 l1 3 8 6 890 655 1990 1470 3230 2380 1 in tpi nominal thread dia in inches threads per inch l1 3 8 12 1o10 745 3680 2710 N m newton meters 1 1 2 6 i180 870 2640 1950 4290 3160 ft lb foot pounds 1 1 2 12 1330 980 2970 2190 4mm x pitch nominal thread dia in millimeters x thread pitch Torque tolerance 0 15 of torquing values Unless otherwise specified use torque values listed above 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 25 Table of Contents Land Pride Section 8 Appendix Notes 26 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Table of Contents Section 8 Appendix Warranty Land Pride warrants to the original purchaser that this Land Pride product will be free from defects in material and workmanship beginning on the date of purchase by the end user according to the following schedule when used as intended and under normal service and conditions for personal use Overall Unit and Drivelines One year Parts and Labor Gearbox S N 329841 5 years on Parts and Labor S N 329840 1 year on Parts and labor Belts blades friction discs in slip clutch and tires Considered wear items This Warranty is limited to the re
11. Engine 50 HP Cutting Width 72 84 Overall Width 77 89 Height 34 Length 69 75 Weight 718 812 Cutting Height 3 4 5 1 4 1 2 increments Deck Material Thickness 3 16 Blades 3 Medium lift Optional blades Low Lift High Lift or Mulching Blade Overlap 1 4 x 2 1 2 x 25 Heat Treated Alloy 1 4 x 2 1 2 x 29 Heat Treated Alloy Steel Steel Blade Spindles 1 1 4 Greasable Blade Tip Speed 18 130 FPM 17 210 FPM Hitch Category 1 Gauge Wheels 3 1 4 x 10 Solid Rubber 4 x 11 Semi Solid Caster Wheel Spindle 1 Diameter with Greasable Bushing Drive Train Driveline 540 RPM PTO Gearbox 1 2 83 Ratio Cast Iron Housing Spring Loaded Single V Belt Front Roller Heavy duty w quick coupler Optional 22 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Table of Contents Section 6 Features and Benefits FDR25 Series Rear Discharge Mowers Features Benefits 2 Key widths 72 and 84 Gearbox HP rating 15 50 HP Rear discharge The wide even dispersal of grass leaves a fine thin layer directly behind the mower vs a possible windrow to the side Keeps grass from blowing in unwanted areas Easier to mow around objects Deflectors Built in to throw material and debris down Clevis type lower Allows for easy hook up by being able to remove pins and back into clevises hitch points Float
12. Never weld a obtaining new labels from your Land Pride Dealer broken or cracked blade ALWAYS replace with a new Land Information about labels is located under Safety Labels in Pride blade to assure safety the Important Safety Information section starting on page 1 BLADE WEAR UNDERCUT OF WING TIP WARNING WORN BEYOND USE aoo MINIMUM FOR 1 4 THICK BLADE 7 32 MINIMUM FOR 5 16 THICK BLADE 7 oy WARNING WORN BEYOND USE oS 3 8 MAXIMUM WEAR WHEN SHARPENING BLEND THESE AREAS ne BLADE TYPICAL BOTH ENDS WORN OR SHARPENED BLADE LAD Inspection of Blades amp Sharpening 19928 Figure 4 1 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 17 Table of Contents Section 4 Maintenance and Lubrication Land Pride Blade Sharpening or Replacement A CAUTION ALWAYS wear eye protection and gloves when sharpening a blade 1 If the blade cutting edge is dull or nicked it should be replaced or sharpened Remove blades for replacing or sharpening by grasping the end of the blade using a rag or a thick padded glove while loosening and removing the bolt bolts that mount the blade Clean blade blade washer and mounting surface of all debris before replacing or sharpening Grind cutting edge at the same bevel as the original See Figure 4 2 Sharpen only the top of the cutting edge to maintain sharpness Blade Sharpening Fi
13. Table of Contents Grooming Mowers FDR2572 amp FDR2584 310 262M Operator s Manual A Read the Operator s manual entirely When you see this symbol the subsequent instructions and warnings are serious follow without exception Your life and the lives of others depend on it Copyright 2007 Printed 10 15 07 Cover photo may show optional equipment not supplied with standard unit Table of Contents i Important Safety Information 1 Section 4 Maintenance and Lubrication 17 Safety at All Times 2000 0055 1 Maintenance 0 cee es 17 Look For The Safety Alert Symbol 1 Service Mowing Blades 00005 18 Safety LabelS sc sinnaeer ona aenbonpanene t 4 Blade Inspection 0 000 18 Introduction cc es cc ee ee ee 7 Blade Sharpening or Replacement 18 ae V Belt Installation 2 eee 18 Application 0 0000 eee 7 Using This Manual 0 000eeeee 7 Storage re 19 Driveline Storage 00000 00 ee 19 Owner Assistance 0000 cee ee eee 7 nae Lubrication 0 ee 20 Section 1 Assembly and Set Up 8 Driveline Shaft U Joints 20 Dealer Preparations 0 00 eee eee 8 Inner Tube Bearings 0 02 21 Preparation Checklist 2 5 8 Driveline Profiles 0 0 0 0 0000 00a 21 Vent Plug Installation 8 Wheel S
14. arbox Type 1 Type of Lubrication Gear Lube EP 80 90W Check the oil level in the gearbox by either removing the dipstick on top of the gearbox or by removing the bottom plug at the rear of the box on the right hand side Add oil if necessary by removing the top dipstick Do not overfill Should your gearbox require service take it OVERFILL to your Land Pride dealer Gearbox Type 2 Unscrew top vent plug in gearbox to remove dipstick Wipe oil from dipstick and screw it back in without tightening Unscrew dipstick and check oil level mark If low fill through top plug hole in gearbox with EP 80 90W oil until oil reaches full mark on the dipstick Reinstall vent plug with dipstick and tighten Take your gearbox to a Land Pride dealer if it requires service Type of Lubrication Gear Lube EP 80 90W Quantity Fill until oil reaches full mark on dipstick IMPORTANT The Type 2 gear box is shipped with the gearbox vent plug and dipstick packaged in the Operator s Manual bag and should have been installed in the gearbox by your Land Pride dealer Please see your Land Pride dealer if the vent plug with dipstick was not included Type 2 Bearing in Blade Spindle Hubs Type of Lubrication Multi purpose Grease 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 21 Table of Contents Section 5 Specifications amp Capacities FDR25 Rear Discharge Series FDR2572 FDR2584 Maximum HP
15. ble The tapered rear design eliminates the need for rear safety chains and greatly reduces the tendency to deposit unsightly clumps of damp grass When weather conditions allow for regular and frequent mowing intervals the rear discharge feature allows for excellent cutting quality and a very well groomed finish Clippings are evenly discharged close behind the mower avoiding streets sidewalks and landscaping The FDR25 Series also features a floating 3 point system to allow for excellent contour following capabilities over hilly and uneven terrain See Section 6 Features and Benefits on page 23 for additional information Using This Manual e This Operator s Manual is designed to help familiarize you with safety assembly operation adjustments troubleshooting and maintenance Read this manual and follow the recommendations to help ensure safe and efficient operation e The information contained within this manual was current at the time of printing Some parts may change slightly to assure you of the best performance e To order a new Operator s or Parts Manual contact your authorized dealer Manuals can also be downloaded free of charge from our website at www landpride com or printed from the Land Pride Service amp Support Center by your dealer Terminology Right or Left as used in this manual is determined by facing the direction the machine will operate while in use unless otherwise stated Defi
16. d to the operator or bystanders ae DN aaa 17362 Belt Tension Figure 3 2 16 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Table of Contents Section 4 Maintenance and Lubrication Maintenance Service Mowing Blades Blade Inspection A caution seein For safety reasons each maintenance operation must be performed with tractor PTO disengaged the mower lowered completely to the ground and the tractor engine shut off with ignition key removed Proper servicing and adjustmentis the key to the long life A DANGER of any implement With careful and systematic Bent Deformed or Split Blades Should be removed from unit inspection you can avoid costly maintenance time and and discarded DO NOT attempt to straighten for reuse repair e After using the mower for several hours check all bolts A to be sure they are tight and check the tension of the WARNING drive belt Refer to Belt Tension in the Adjustments DO NOT attempt to modify blade such as hard surfacing heat section on page 16 or cold treating and or by any other method e Lubricate items as listed under Lubrication this section starting on page 20 A DANGER Blade Wear As blades wear and are sharpened the blade performance will be reduced e Replace any worn damaged or illegible safety labels by DO NOT try to straighten a blade that is bent
17. ded later Safety decals are legible and undamaged from shipment PTO shaft and loose parts bag box shipped with the Grooming Mower Vent Plug Installation Refer to Figure 1 1 IMPORTANT Series FDR16 Grooming Mowers are shipped with a red plug in the gear box to prevent loss of oil during shipping and handling This plug must be replaced with a vent plug before operating the mower A vent plug for the gearbox is included in a bag with the manual See your nearest Land Pride Dealer if vent plug is missing Remove temporary plug from top of splitter gearbox and replace with supplied vent plug with dipstick voni Rug gt Sm we Oil Level E A Plug l DO NOT OVERFILL Vent Plug Location Figure 1 1 Tractor Requirements Tractor horse power rating should be between 15 amp 50 PTO horsepower Tractors outside this horsepower range must not be used The rear power take off PTO speed must be capable 540 RPM and have a 1 3 8 6 spline A 3 Point Category hitch is required The lower 3 Point arms must be stabilized to prevent side to side movement Most tractors have sway blocks or adjustable chains for this purpose NOTE Ballast may need to be added to your tractor to maintain steering control Refer to your tractor s operator manual to determine if one needs additional ballast Protective Equipment The tractor MUST be equipped with protective equipment designed to shi
18. eld the operator from thrown objects and from tractor roll over An enclosed tractor cab with a Roll Over Protective Structure ROPS may qualify See tractors manual for type of protection your tractor has 8 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Section 1 Assembly and Set Up Table of Contents A Frame Refer to Figure 1 2 1 There are flat washers placed between the rear braces 1 and the rear hitch plates 5 for shipping Remove the flat washers and reassemble the rear braces Do not tighten bolt and nut at this time The lower holes of the A Frame 2 are bolted to the shipping crate with lag bolts for shipping Remove the lag bolts from the A Frame Loosen the 5 8 nut 6 This will allow the hitch to be rotated into to position Rotate the rear hitch braces 1 up until the lower holes of the A Frame 2 line up with the top holes of the hitch plates on the deck Secure with the 5 8 flange bolts 3 and 5 8 flange nut 4 already mounted in the holes of the front hitch plates Tighten all hardware in the rear hitch braces and A Frame 17365 Hitch Braces Assembly Figure 1 2 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 9 Table of Contents Section 1 Assembly and Set Up Land Pride Front Roller Refer to Figure 1 3 1 Remove the front two 1 2 13 x 1 1 2 GR5 hex flange serrated screws 9 and reinsert from the
19. ers especially children on tractor Do not operate with bystanders in mowing area Do not operate with deflectors guards removed Do not place hands or feet under deck when operating 81 8 555C 17360 or when engine is running 818 5550 CCC M Danger Rotating Blade d 4 THROWN OBJECT HAZARD To prevent serious injury or death from thrown object Operate only with all guards installed and in good condition Stop operation if bystanders come within several hundred feet 81 8 556C 818 556C aA Danger Thrown Object 838 270C Caution V Belt Installation FDR2572 838 116C Caution V Belt Installation FDR2584 6 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Introduction Table of Contents Land Pride welcomes you to the growing family of new product owners This implement has been designed with care and built by skilled workers using quality materials Proper assembly maintenance and safe operating practices will help you get years of satisfactory use from the machine Application Land Pride s 25 Series Rear Discharge Grooming Mower is an excellent choice for homeowners campuses parks and golf courses They are adapted for category 1 three point hitch mounting on tractors in the 15 to 50hp range They are also Quick Hitch adapta
20. gth Too long a driveline can damage tractor gearbox and driveline Do not use a PTO adaptor with a quick hitch A PTO adapter will increase strain on the tractor s PTO shaft resulting in possible damage the shaft and driveline Checking Driveline Minimum Length Refer to Figure 1 6 1 Start tractor and slowly engage 3 point controls to move lower arms until the gearbox shaft is approximately level with the tractor s PTO shaft A WARNING 2 Slide inner yoke of driveline over the gearbox shaft Damaged drivelines can cause serious injury or death and secure with locking collar 3 Slide outer yoke of driveline over the tractor PTO shaft and secure with locking collar A CAUTION Tractor PTO shield and all Grooming Mower guards must be i 2 4 in place at all times during operation maa A CAUTION Always engage parking brake shut off tractor and remove key before dismounting from tractor HIELD E J N IMPORTANT Some tractors are equipped with HI Beet g multispeed PTO ranges Be certain your tractor s RACTOR END B OUTER SHA Ra PTO is set for 540 rpm CUTER SHIELD 22009 Driveline Shortening IMPORTANT Avoid premature driveline Figure 1 6 breakdown A driveline that is operating must not a eke exceed an angle of 25 degrees up or down while 4 The driveline will require shortening if it does not fit operating the 3 point lift See Figure 1 5 below ete tractor and mower S
21. gure 4 2 HORIZONTAL 19046 O 4 O i NAIL OR SHAFT Blade Balancing Figure 4 3 NOTE Care should be taken in order not to remove any more material than necessary to sharpen blade 3 Check blade balance by positioning the blade horizontally on a nail or shaft through the center hole See Figure 4 3 If either end of the blade rotates downward grind remove metal on that end until the blade will balance The blade is properly balanced when neither end drops Balance of a blade is generally maintained by removing an equal amount of material from each end of the blade when sharpening IMPORTANT Always install blade with the cutting IMPORTANT Replace blades with Land Pride edge facing direction of rotation blades only 4 Mount blade with wing tips pointing up towards bottom of deck Reinstall blade blade washer and bolt Care should be taken when installing blade bolt not to get it cross threaded Do not exceed 55 ft lbs of torque on bolt V Belt Installation Refer to Figure 4 4 and Figure 4 5 These illustrations are also on the labels located on the top of the mower decks 1 2 Remove right and left hand belt covers Disengage belt tension by loosening eyebolt 1 and removing spring 2 from the tension chain link 3 With tension relieved from belt remove old belt from pulleys To install a new belt be sure the belt is positioned in all the pulley grooves Engage belt tensi
22. horten driveline as ollows a Raise or lower 3 point lower arms until mower and tractor PTO shafts are approximately level with each other Securely block Grooming Mower frame in this position b Set tractor in park shut tractor engine off set park DRIVELINE brake and remove switch key c Pull driveline apart into two sections as shown in Figure 1 6 Attach outer driveline universal joint to the tractor PTO shaft Attach inner driveline universal joint to the gearbox shaft Pull on each driveline section to be sure universal joints are secured to the shafts d Hold driveline sections parallel to each other to Maximum Allowable Driveline Movement determine if they are too long The inner and outer Figure 1 5 shields on each section should end approximately 1 short of reaching the universal joint shield on IMPORTANT Always check driveline minimum length during initial setup when connecting to a different tractor and when alternating between using a quick hitch and a standard 3 point hitch More than one driveline may be required to fit all applications the adjacent section see B dimension If they are too long measure 1 B dimension back from the universal joint shield and make a mark at this location on the inner and outer driveline shields 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 11 Table of Contents Section 1 Assembly and Set Up Land Pride e Cut off inner
23. ing 3 point Top and bottom hitch points float up and down which allows the mower to float over uneven terrain 5 16 Rolled front on deck Heavy front takes abuse Frame over deck design Frames takes stress out of deck by supporting it adjust in and out FDR2572 Only Solid rubber Solid rubber tires on the FDR2572 are sandwiched between the rim halves bolted in and tires with roller bearings can t go flat Roller bearings allow for a long life FDR2584 Only Semi solid Semi solid tires on the FDR2584 offer premium flotation Roller bearings allow for a long life tires with roller bearings Semi solid tires offer shock absorption Choices of blades Low medium high lift or mulching blades are available to match customer needs and specific applications High blade tip speed 72 18 130 fom For cleaner cutting and better dispersion of clippings 84 17 210 fom 1 3 8 Machined blade spindle Machined spindle for balanced performance and accuracy ball bearings for smooth and with ball bearings quiet running cast iron housing for added protection and durability and cast iron housing Top greasing spindles Assures top bearing gets grease No shields to remove Single B section Kevlar belt Simple one belt design Kevlar material adds additional strength Vacuum formed No scratching no rattling ABS belt guards Non aligned gauge wheels Rear wheels don t track behind the front wheels to
24. intenance and storage of WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury and includes hazards that are exposed when guards are removed It may also be used to alert against unsafe practices A CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices For Your Protection A Thoroughly read and understand the Safety Label section read all instructions noted on them F Shutdown and Storage A Lower machine to ground put tractor in park turn off engine and remove the key A Detach and store implements in a area where children normally do not play Secure implement by using blocks and supports 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 1 Important Safety Information Table of Contents Land Pride These are common practices that may or may not be applicable to the products described in this manual Use Safety Lights and Devices A Slow moving tractors self propelled equipment and towed implements can create a hazard when driven on public roads They are difficult to see especially at night A Flashing warning lights and turn signals are recommended whenever driving on public roads Use lights and devices provided with implement
25. lied is made with respect to this sale and all implied warranties of merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are hereby disclaimed and excluded from this sale This Warranty is not valid unless registered with Land Pride within 30 days from the date of purchase by the end user 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 27 Corporate Office PO Box 5060 Salina Kansas 67402 5060 USA www landpride com
26. mplement A Do not leave tractor or implement unattended with engine running A Dismounting from a moving tractor could cause serious injury or death A Do not stand between the tractor and implement during hitching A Keep hands feet and clothing away from power driven parts A Wear snug fitting clothing to avoid entanglement with moving parts A Watch out for wires trees etc when raising implement Make sure all persons are clear of working area A Turning tractor too tight may cause implement to ride up on wheels This could result in injury or equipment damage equipment Be Aware of Signal Words A Signal word designates a degree or level of hazard seriousness The signal words are A DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious injury This signal word is limited to the most extreme situations typically for machine components that for functional purposes cannot be guarded Look For The Safety Alert Symbol The SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken When you see this symbol be alert and carefully read the message that follows it In addition to design and configuration of equipment hazard control and accident prevention are dependent upon the awareness concern prudence and proper training of personnel involved in the operation transport ma
27. n 1 2 increments Refer to Leveling the Mower at the top of this page 3 Point Hitch Adjustments The 3 point hitch system on this mower has been designed for front to back flotation when mowing on uneven terrain Adjust the tractor s top link to place the upper hitch pin vertically above the lower hitch pins as shown in Figure 3 1 A CAUTION Engage parking brake shut off tractor remove key and disengage PTO before making any height adjustments Belt Tension Refer to Figure 3 2 Ay CAUTION Belt drive system under spring tension use care to avoid bodily harm 1 To check tension apply force at arrow A with a tension tester and deflect the belt 1 4 The force required to get this deflection should range from 7 to 10 Ibs 2 To adjust belt tension adjust eyebolt 1 as necessary This adjustment will increase or decrease the tension on spring 2 If more tension is needed than the eyebolt can adjust take the tension spring 2 to next link in the tension chain 3 3 Excessive tension on the belt may lead to premature failure of belt and drive components Excessive tension on the belt may also lead to a safety hazard to the operator or bystanders Not enough tension on the belt may lead to premature failure of the belt due to excessive slipping Ay warnine Excessive tension on the belt may lead to premature failure of belt and drive components Excessive tension on the belt may also lead to a safety hazar
28. nitions NOTE A special point of information that the operator must be aware of before continuing IMPORTANT A special point of information related to its preceding topic Land Pride s intention is that this information should be read and noted before continuing Owner Assistance The Warranty Registration card should be filled out by the dealer at the time of purchase This information is necessary to provide you with quality customer service If customer service or repair parts are required contact a Land Pride dealer A dealer has trained personnel repair parts and equipment needed to service the mower The parts on your Grooming Mower have been specially designed and should only be replaced with genuine Land Pride parts Therefore should your mower require replacement parts go to your Land Pride Dealer Serial Number Plate For prompt service always use the serial number and model number when ordering parts from your Land Pride dealer Be sure to include your serial and model numbers in correspondence also Refer to Figure 1 for the location of your serial number plate Serial Number Plate Location Figure 1 Further Assistance Your dealer wants you to be satisfied with your new Grooming Mower If for any reason you do not understand any part of this manual or are not satisfied with the service received the following actions are suggested 1 Discuss the matter with your dealership service manager making su
29. on by assembling the tension spring back on the eyebolt and tightening the eyebolt to apply tension to new belt Check the belt tension refer to Figure 3 2 on page 16 Reinstall all belt covers and secure in place with hardware FDR2572 V Belt Installation Figure 4 4 FDR2584 V Belt Installation Figure 4 5 18 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Table of Contents Section 4 Maintenance and Lubrication Storage At the end of the working season or when the mower will not be used for a long period it is good practice to clean off any dirt or grease that may have accumulated on the mower and any of the moving parts 1 Clean off any dirt or grease that may have accumulated on the Grooming Mower and moving parts Scrape off compacted dirt from the bottom of the deck and then wash the surface thoroughly with a garden hose A coating of oil may also be applied to the lower deck area to minimize oxidation Check the blades for wear and replace if necessary see Service Mowing Blades this section on page 17 Inspect the mower for loose damaged or worn parts and adjust or replace as needed Lubricate as noted in the Lubrication portion of this section starting on page 20 Store the Grooming Mower in aclean dry place The deck should be positioned on a flat surface Ensure that the deck is stable Repaint parts where paint is wo
30. ound speed of approximately 4 5mph The proper mowing speed will ultimately be determined by ground conditions desired finish common sense and good safe mowing practices by the operator Grass is best cut when it is dry Mowing in wet grass can cause plugging resulting in grass clumps behind the mower Grass should be mowed frequently as shorter clippings deteriorate faster When mowing in tall grass it is best to raise the cutting height mow the area then lower the cutting height and mow a second time After mowing approximately 50 ft stop the tractor disengage the PTO set the brake turn off the engine remove the key and dismount the tractor to see if the mower is adjusted properly If you need to dismount the tractor on a hill or incline to inspect adjust or park the mower for any reason place wheel chocks under the rear tires for added safety Once you have made necessary adjustments you may continue mowing Do not engage the PTO at high engine rpm and avoid making sharp turns if at all possible If anyone approaches while you are mowing disengage the PTO and stop the tractor With a little practice and experience you will become very good at operating your Land Pride FDR25 Rear Discharge Grooming Mower Always remember that there is no substitute for proper maintenance and good safe operating practices See Features and Benefits section or Product Specifications for additional information and performance enhancing
31. placement of any defective part by Land Pride and the installation by the dealer of any such replacement part and does not cover common wear items Land Pride reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship This Warranty does not apply to any part or product which in Land Pride s judgment shall have been misused or damaged by accident or lack of normal maintenance or care or which has been repaired or altered in a way which adversely affects its performance or reliability or which has been used for a purpose for which the product is not designed Misuse also specifically includes failure to properly maintain oil levels grease points and driveline shafts Claims under this Warranty should be made to the dealer which originally sold the product and all warranty adjustments must be made through an authorized Land Pride dealer Land Pride reserves the right to make changes in materials or design of the product at any time without notice This Warranty shall not be interpreted to render Land Pride liable for damages of any kind direct consequential or contingent to property Furthermore Land Pride shall not be liable for damages resulting from any cause beyond its reasonable control This Warranty does not extend to loss of crops any expense or loss for labor supplies rental machinery or for any other reason No other warranty of any kind whatsoever express or imp
32. r expressed or implied While every precaution has been taken in the preparation of this manual Land Pride assumes no responsibility for errors or omissions Neither is any liability assumed for damages resulting from the use of the information contained herein Land Pride reserves the right to revise and improve its products as it sees fit This publication describes the state of this product at the time of its publication and may not reflect the product in the future Land Pride is a registered trademark All other brands and product names are trademarks or registered trademarks of their respective holders Printed in the United States of America FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Important Safety Information Table of Contents These are common practices that may or may not be applicable to the products described in this manual Safety at All Times Thoroughly read and understand the instructions given in this manual before operation Refer to the Safety Label section read all instructions noted on them Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment A Operator should be familiar with all functions of the unit A Operate implement from the driver s seat only A Make sure all guards and shields are in place and secured before operating the i
33. rded for this use Using the deck as a fan can result in injury and or death A DANGER Do not operate and or travel across steep inclines where a tractor can roll over resulting in serious injury or death Consult your tractor s manual for acceptable inclines the tractor is capable of traveling across A CAUTION When mowing in sandy soil areas wear may occur to your mower blades caused from sand erosion Frequent inspection should be made and blades replaced if damaged Low lift blades are available from your Land Pride dealer 1 Clear the area to be mowed of rocks branches and other foreign objects that might be picked up and thrown by the mower blades IMPORTANT Do not exceed rated PTO speed of mower Excessive engine speed will cause damage to the power train components IMPORTANT Stop PTO rotation immediately if vibration occurs during operation Wait for mower to come to a complete stop Follow all tractor shut down procedures before dismounting from the tractor to check for probable causes 2 Lower mower to ground Set tractor throttle at idle Engage PTO to start blades rotating 3 Operate with 540 rpm PTO tractor Mower blades will cut better at a 540 RPM than at reduced throttle 4 At first begin mowing in a low gear and shift up until the desired speed is achieved maintain 540 PTO rpm regardless of gear selection 5 After mowing the first 50 feet stop and check to see that the mower is adjusted p
34. re he is aware of any problems you may have and that he has had the opportunity to assist you 2 Ifyou are still not satisfied seek out the owner or general manager of the dealership explain the problem and request assistance 3 For further assistance write to Land Pride Service Department 1525 East North Street P O Box 5060 Salina Ks 67402 5060 E mail address lpservicedept landpride com 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 7 Table of Contents Section 1 Assembly and Set Up Dealer Preparations This Grooming Mower has been assembled at the factory Some preparation will be necessary to attach the Grooming Mower to the customer s tractor Ensure that the intended tractor conforms to the requirements stated under the heading Tractor Requirements below Preparation Checklist Miscellaneous assembly tools hammer tape measure hacksaw spirit level and assortment of wrenches and sockets Possible need for forklift or hoist capable of lifting 2500 Ibs Auxiliary tractor weights depending on tractor size A minimum of two people available during assembly If a pin bolt or other part has been removed and you are unsure where it is used use the Parts Manual to identify it Be sure the part gets used in the correct location By double checking while you assemble you will lessen the chance of using a bolt incorrectly that may be nee
35. reduce laying grass over Spring loaded adjustable idler Allows for constant and proper tension on belt Better than adjusting gearbox for belt tension Quick Hitch Compatible Compatible with Land Pride Quick Hitch for easy attachment and removal increases productivity 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 23 Table of Contents Section 7 Troubleshooting Rear discharge area plugged Check installation of belt Wait until grass dries Raise cutting height of mower and cut grass twice Mow at full throttle 540 PTO rpm check PTO speed and tractor engine Shift transmission to a lower gear A CAUTION Do not try to clean rear discharge area when mower is running Bodily harm may occur Belt slipping Unplug and clean mower deck Remove belt guard shields and clean sheaves Tighten spring take up eyebolt Replace belt Patches of uncut grass Mow at full throttle 640 PTO rpm check PTO speed and tractor engine Shift transmission to a lower gear Tighten spring take up eyebolt Sharpen and balance or replace blade Excessive vibration Replace blades Replace drive belt Replace pulleys or align Remove belt guard shields amp clean debris from belt area amp sheaves Gearbox noisy Check lubricant level Blades scalping grass Raise cutting height by adjusting wheels Change mowing pattern Reduce speed turns Uneven cut Shift to a lower gear
36. rn or scratched to prevent rust Ask your dealer for Aerosol Land Pride touch up paint Land Pride Touch up Paint Part No Part Description 821 011C PAINT LP BEIGE SPRAY CAN 821 002C PAINT GP BLACK SPRAY CAN Driveline Storage Refer to Figure 4 6 The FDR25 series mowers are equipped with a driveline hanger so that the drivelines can be stored up off the ground 19301 Driveline Storage Figure 4 6 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 19 Section 4 Maintenance and Lubrication Table of Contents Land Pride Lubrication Driveline Shaft U Joints Type of Lubrication Multi purpose Grease Quantity 4 to 8 Pumps D Inner Tube Bearings Type of Lubrication Multi purpose Grease Quantity As Required D Driveline Profiles Type of Lubrication Multi purpose Grease Quantity Clean amp coat inner profile tube of driveline with a light film of grease and then reassemble Wheel Support Bushings amp Wheel Bearings Type of Lubrication Multi purpose Grease 20 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Table of Contents Section 4 Maintenance and Lubrication DO NOT IMPORTANT Do not overfill Level mower and wait for gearbox oil to cool before checking A mower that is not level or a gearbox with hot oil will not show correct oil level on the dipstick Ge
37. roperly 6 Donot make sharp turns or attempt to back up while mower is on the ground 7 Do not engage PTO with mower in the fully raised position Do not engage or disengage PTO at full throttle 8 Grass is best cut when it is dry Mowing wet grass can cause plugging resulting in grass clumps behind the mower 9 Grass should be mowed frequently as shorter clippings deteriorate faster 10 If mowing extremely tall grass it is best to raise cutting height and mow the area then lower cutting height and mow a second time at the desired height 11 Periodically check for foreign objects wrapped around the Grooming Mower blades Remove foreign objects only after following Tractor Shut Down Procedure on page 13 Un hooking the Mower The following steps should be done when un hooking the Grooming Mower from the tractor 1 Park ona level solid surface 2 Shut tractor engine off and engage parking brake 3 Lower deck to level ground or onto blocks supporting the deck just above ground level 4 Follow all tractor shut down procedures outlined on page 13 before dismounting from the tractor 5 Unhitch Grooming Mower from tractor 6 See Storage on page 19 if mower is not going to be used for a long time 14 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Section 2 Operating Instructions Table of Contents General Operating Instructions By now you should have thoroughly
38. should be sufficient clearance for the operator when mounted to a tractor with a cab or that is equipped with ROPS A The ROPS may need to be extended or flipped around to obtain sufficient clearance 2 FDR2572 amp FDR2584 Grooming Mowers 310 262M 10 15 07 Land Pride Table of Contents Important Safety Information These are common practices that may or may not be applicable to the products described in this manual Prepare for Emergencies A Be prepared if a fire starts A Keep a first aid kit and fire extinguisher handy A Keep emergency numbers for doctor ambulance hospital and fire department near phone Tire Safety A Tire changing can be dangerous and should be performed by trained personnel using the correct tools and equipment A When inflating tires use a clip on chuck and extension hose long enough to allow you to stand to one side and NOT in front of or over the tire assembly Use a safety cage if available A When removing and installing wheels use wheel handling equipment adequate for the weight involved Wear Protective Equipment A Protective clothing and equipment should be worn A Wear clothing and equipment appropriate for the job Avoid loose fitting clothing A Prolonged exposure to loud noise can cause hearing impairment or hearing loss Wear suitable hearing protection such as earmuffs or earplugs A Operating equipment safely requires
39. ssory lights and devices for adequate warning to operators of other vehicles Comply with all Federal State and local laws NOTE Always disengage PTO before raising the mower to transport position 1 When raising mower to transport position be sure driveline does not contact tractor or mower Adjust and set tractor s 3 point hitch lift height so that the PTO shaft does not contact mower deck in the fully raised position 2 Be sure to reduce tractor ground speed when turning and leave enough clearance so the mower does not contact obstacles such as buildings trees or fences 3 Select a safe ground travel speed when transporting from one area to another When traveling on roadways transport in such a way that faster moving vehicles may pass you safely A slow moving vehicle sign should always be properly displayed when traveling on public roads or right of ways 4 Shift tractor to a lower gear when traveling over rough or hilly terrain 10 15 07 FDR2572 amp FDR2584 Grooming Mowers 310 262M 13 Table of Contents Section 2 Operating Instructions Land Pride Mowing Instructions A DANGER Gearbox shields must be secured in place when operating to avoid injury or death from entanglement in rotating drivelines Ay CAUTION Do not over speed PTO or machine damage may result Know what your tractor requirements are A DANGER Do not use deck as a fan Cutting blades are not properly designed or gua
40. t down as noted below before making any inspections maintenance and or repairs to the tractor and or mower 1 Park tractor on a level surface Don t work under or around an implement parked on a steep incline Place tractor in park and set park brake Disengage PTO if operating Shut engine off and remove switch key Wait for PTO to come to a complete stop before dismounting tractor 6 Wear safety glasses Operation Check It is absolutely essential that no one operates the Grooming Mower without first having read fully understood and become totally familiar with the Operator s Manual Make sure the operator has paid particular attention to Ore ON Important Safety Information page 1 e Section 1 Assembly and Set Up page 8 e Section 2 Operating Instructions page 13 e Section 3 Adjustments page 16 e Section 4 Maintenance and Lubrication page 17 Make the following inspections after attaching the Grooming Mower to the tractor See hook up instructions beginning on page 10 Make certain PTO is disengaged and completely stopped before continuing 1 Inspect tractor safety equipment to make sure it is in good working condition 2 Complete the Operating Checklist below Operating Checklist Check Check oil level in gearboxes Reference Section 5 Page 21 Check that all plugs in gearbox Section 5 have been replaced properly Page 21 Check initially and periodically for Section 8 Page 25
41. upport Bushings amp Wheel Bearings 21 Tractor Requirements 00 8 Gearbox Type 1 0c cece eee eee 21 Protective Equipment 00 8 Gearbox Type 2 000 e eee 21 A Frame wanes ctor teaser cess ehea ea anaes 9 Bearing in Blade Spindle Hubs 25 Front Roller x i etn varie bat wo baie Sew ew 10 Section 5 Specifications amp Capacities _ 25 Tractor Hook Up 0000s 10 Driveline Installatigti 4 2sdesesoenadones 11 Section 6 Features and Benefits 25 5 pete Drelin e LEMONN aa sanaaa z Section 7 Troubleshooting 25 ection 2 Operating Instructions Tractor Shut Down Procedure 13 PeO U OMS APPENA E asian datae ee Operating Check 0 0 cceceeeeeeee 13 Torque Values Chart for Common Bolt Sizes 25 Transporting Terese aang es eye tu ae enegennyeaeseaes 13 NOTES asia ie 32 econ Sk ee ae Be eo a EA 27 Mowing Instructions 00 000008 14 Warranty 0 eset e eet eee eee 27 Un hooking the Mower 000 14 General Operating Instructions 15 Section 3 Adjustments 16 Leveling the Mower 05 16 Cutting Height Adjustment 16 3 Point Hitch Adjustments 16 Bell TONON 2 4005 rr o esr eee se eas 16 Copyright 2007 All rights Reserved Land Pride provides this publication as is without warranty of any kind eithe
Download Pdf Manuals
Related Search