La Crosse Technology WS-7044U User's Manual
Contents
1. 3 Be sure there are no obstructing objects 4 Be sure all batteries are fresh Problem The LCD screens are faint dim Solution Replace batteries Note For problems not solved please contact La Crosse Technology 19 MAINTENANCE AND CARE INSTRUCTIONS e Extreme and sudden temperature changes vibration and shock should be avoided to prevent damage to the units e Clean displays and units with a soft damp cloth Do not use solvents or scouring agents they may mark the displays and casings e Do not submerge in water e Immediately remove all low powered batteries to avoid leakage and damage e Opening the casings invalidates the warranty Do not try to repair the unit Contact La Crosse Technology for repairs 20 SPECIFICATIONS Temperature measuring range Indoor 32 F to 104 F with 0 2 F resolution 0 C to 40 C with 0 1 C resolution OFL displayed if outside this range Outdoor 21 9 F to 157 9 F with 0 2 F resolution 29 9 C to 69 9 C with 0 1 C resolution OFL displayed if outside this range Temperature checking intervals Indoor Every 10 seconds Outdoor 3 times every 10 minutes Transmitting 433 92 MHz frequency Temperature Maximum 80ft 25m in open transmitting space and free from interference range 21 Power Source Weather 2 x AAA 1 5V IEC LR3 Station Sensor 2 x AAA2. covered by this warranty If necessary repairs are not covered by this warranty or if a product is examined which is not in need or repair you will be charged for the repairs or examination The owner must pay any shipping charges incurred in getting your La Crosse Technology Ltd product to a La Crosse Technology Ltd authorized service center La Crosse Technology Ltd will pay ground return shipping charges to the owner of the product to a USA address only Your La Crosse Technology Ltd warranty covers all defects in material and workmanship with the following specified exceptions 1 damage caused by accident unreasonable use or neglect including the lack of reasonable and necessary maintenance 2 damage occurring during shipment claims must be presented to the carrier 3 damage to or deterioration of any accessory or decorative surface 4 damage resulting from failure to follow instructions contained in your owner s manual 5 damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology Ltd authorized service center 6 units used for other than home use 7 applications and uses that this product was not intended or 8 the products inability to receive a signal due to any source of interference This warranty covers only actual defects within the product itself and does not cover the cost of installation or removal from a fixed installation normal set up
3. time The WS 7044U averages past air pressure readings to provide an accurate forecast causing a necessity to disregard all weather forecasting for 12 24 hours after the unit has been set up reset or moved from one altitude to another i e from one floor of a building to another In areas where the weather is not affected by the change of air pressure this feature will be less accurate A WEATHER ICONS 10 There are 3 possible weather icons that will be displayed in the FORECAST LCD Sunny indicates that the weather 7 is expected to improve not that the weather will be sunny lt 7g Sun with Clouds SS indicates that A the weather is expected to be fair not that the weather will be sunny with clouds 7 Clouds with Rain indicates that the weather is expected to get Ga worse not that the weather will be rainy The weather icons change when the unit detects a change in air pressure The icons 11 change in order from sunny to sun with clouds to clouds with rain or the reverse It will not change from sunny directly to rainy although it is possible for the change to occur quickly If the symbols do not change then the weather has not changed or the change has been too slow and gradual to register WEATHER TENDENCY ARROWS Other possible displays in the FORECAST LCD are 2 weather tendency arrows one that points up under the forecast icons and one th
4. 1 5V IEC LR3 Dimensions L x W x H Weather 2 95 x 0 83 x 10in 75 x 21 x Station 255mm Sensor 2 32 x 0 83 x 2 56in 59 x 21 x 65mm WARRANTY INFORMATION La Crosse Technology Ltd provides a 1 year limited warranty on this product against manufacturing defects in materials and workmanship This limited warranty begins on the original date of purchase is valid only on products purchased and used in North America and only to the original purchaser of this product To receive warranty service the purchaser must contact La Crosse Technology Ltd for problem determination and service procedures Warranty service can only be performed by a La Crosse Technology Ltd authorized service center The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology Ltd or La Crosse Technology Ltd s authorized service center 22 La Crosse Technology Ltd will repair or replace this product at our option and at no charge as stipulated herein with new or reconditioned parts or products if found to be defective during the limited warranty period specified above All replaced parts and products become the property of La Crosse Technology Ltd and must be returned to La Crosse Technology Ltd Replacement parts and products assume the remaining original warranty or ninety 90 days whichever is longer La Crosse Technology Ltd will pay all expenses for labor and materials for all repairs
5. WS 7044U Wireless 433 MHz Miniature Wood Weather Station Instruction Manual LA CROSSE TECHNOLOGY TABLE OF CONTENTS Topic Page Inventory of Contents Additional 3 Equipment Quick set up guide 3 Battery installation 4 6 Time 7 8 Features 9 15 Indoor temperature 10 Weather Forecast icons amp tendency 10 13 arrows Outdoor temperature with 13 15 Minimum amp Maximum Mounting 15 19 Troubleshooting 19 Maintenance and Care instructions 20 Specifications 21 22 INVENTORY OF CONTENTS 1 WS 7044U Weather Station 2 TX2U Remote Temperature Sensor 3 Three each Philips screws 4 One strip double sided adhesive tape 5 Instruction manual amp Warranty card ADDITIONAL EQUIPMENT 1 Four fresh AAA 1 5V batteries 2 One Philips screwdriver QUICK SET UP GUIDE 1 Insert two AAA batteries into each unit 2 Wait 10 minutes to ensure transmission reception 3 Set the time 4 Mount units in desired locations DETAILED SET UP GUIDE I BATTERY INSTALLATION A REMOTE TEMPERATURE SENSOR 1 Remove the battery cover Place your thumb over the two air vent slots on the face of the Remote Temperature Sensor push down gently slide battery cover down and off Observing the correct polarity install 2 AAA batteries The batteries will fit tightly to avoid start up problems make sure that they do not spring free during installation Repl
6. ace the battery cover Battery Cover B WEATHER TEMPERATURE STATION 1 Remove the battery cover Pull up and out from the slot located in the central position of the battery cover 2 Observing the correct polarity install 2 AAA batteries The batteries will fit tightly to avoid start up problems make sure that they do not spring free during installation 3 Replace the battery cover Note After the batteries have been installed into the Weather Temperature Station the LCD segments should light up Also within 3 minutes the Outdoor Temperature should be displayed in the OUTDOOR LCD If any of this does not occur remove all batteries 5 and install them again carefully observing the polarity C LOW BATTERY amp BATTERY REPLACEMENT FEATURES When the batteries become weak in the Weather Temperature Station a low battery indicator shaped as a battery appears in the LCD screen between the Hour display and the Minute display When you replace the batteries in the Weather Temperature Station the LCD screen will continue to display its stored information for 20 seconds This means that if you can install the new batteries within this 20 second time period you do not need to program the Station again I TIME A THE TIME DISPLAY The time is displayed vertically with the hour displayed above the minutes rather than in the conventional horizontal format The hour and m
7. at points down above the forecast icons These arrows reflect current changes in the air pressure An arrow pointing up indicates that the air pressure is increasing and the weather is expected to improve or remain good an arrow pointing down indicates that the air pressure is decreasing and the weather is expected to become worse or remain poor No arrow means the pressure is stable 12 Il OUTDOOR TEMPERATURE WITH MINIMUM amp MAXIMUM FEATURE The Weather Temperature Station receives the outdoor temperature from the Remote Temperature Sensor and the temperature appears in the OUTDOOR LCD The Remote Temperature Sensor makes a temperature update every minute and transmits a new temperature to the Weather Temperature Station 3 times every 10 minutes The Weather Temperature Station also keeps a record of the Minimum and Maximum temperatures it has recorded 13 A VIEWING THE MINIMUM MAXIMUM TEMPERATURES 1 Press the circular MIN MAX button under all LCD displays once An arrow will appear and point to the MIN that is printed in the right hand margin The minimum recorded temperature will display in the OUDOOR LCD 2 Press the MIN MAX a second time and the arrow will shift to point to the MAX that is printed in the right hand margin The maximum recorded temperature is now displayed in the OUTDOOR LCD 3 Press the MIN MAX a third time and the OUTDOOR LCD returns to display the current outdoor te
8. he mounting surface with a pencil 3 Where marked start the screw holes 16 into the mounting surface Screw mounting bracket onto the mounting surface Ensure that the screws are flush with the bracket Snap the Remote Temperature Sensor onto the mounted bracket B MOUNTING WITH ADHESIVE TAPE 1 With a nonabrasive solution clean and dry the back of the mounting bracket and the mounting surface to ensure a secure hold The mounting surface should be smooth and flat Remove the protective strip from one side of the tape Adhere the tape to the designated area on the back of the mounting bracket Remove the protective strip from the other side of the tape Position the Remote Temperature Sensor in the desired location ensuring that the Weather Temperature Station can receive the signal 17 Il THE WEATHER STATION The Weather Station can be mounted on the wall with the use of a wall hanging screw not included A WALL MOUNTING 1 Place a screw not included into an appropriate wall leaving approximately 3 16 of an inch 5mm extended from the wall 2 Place the Weather Station onto the screw using the hanging hole on the backside Gently pull the Station down to lock the screw into place TROUBLESHOOTING Problem No outdoor temperature is displayed Solution 1 Remove all batteries wait 30 seconds then reinsert into sensor first then into the station 18 2 Place sensor closer to station
9. inute displays are separated by a flashing dot which indicates the seconds The time is only displayed in the 12h mode there is no 24h option B SETTING THE TIME Note The SET and the buttons are located on the backside of the Weather Temperature Station and are labeled accordingly If no buttons are pressed within 10 seconds of pressing the SET button the Weather Temperature Station will return to its normal time display 1 Press the SET button The hour digit in 7 the HOUR LCD will flash Press the button repeatedly until you reach your desired hour Press the SET button a second time The minute digit in the MINUTE LCD will flash Press the button repeatedly until you reach your desired minute Press the SET button again to confirm settings and to return to the normal time display FEATURES Note All temperatures are read in F there is no option to read the temperature in TC HOUR LCD INDOOR LCD MINUTE LCD FORECAST LCD OUTDOOR LCD MINIMUM MAXIMUM BUTTON Il I INDOOR TEMPERATURE The Weather Temperature Station monitors the temperature within its immediate proximity and displays this temperature in the INDOOR LCD The temperature is monitored as soon as the batteries are installed WEATHER FORECAST The weather forecasting feature is estimated to be 75 accurate The weather forecast is based solely upon the change of air pressure over
10. mperature 14 B RESETTING THE MINIMUM MAXIMUM TEMPERATURE 1 Press and hold the MIN MAX button for 3 seconds This will reset all records to the current outdoor temperature MOUNTING Note Extreme and sudden changes in temperature will decrease the accuracy of the Weather Temperature Station and changes in elevation will result with inaccurate weather forecasting for the next 12 to 24 hours These changes will require a 12 to 24 hour wait before obtaining reliable data To achieve a true temperature reading avoid mounting where direct sunlight can reach the Remote Temperature Sensor We recommend that you mount the Remote Temperature Sensor on a North facing wall The sending range is 80ft 25m obstacles such as walls concrete and large metal objects can reduce the range Place both units in their 15 desired location and wait approximately 10 minutes before permanently mounting to ensure that there is proper reception The Weather Temperature Station should display a temperature in the OUTDOOR LCD within 3 minutes of setting up THE REMOTE TEMPERATURE SENSOR The Remote Temperature Sensor can be mounted in two ways e with the use of screws or e using the adhesive tape A MOUNTING WITH SCREWS 1 Remove the mounting bracket from the Remote Temperature Sensor The bracket should snap off easily 2 Place the mounting bracket over the desired location Through the three screw holes of the bracket mark t
11. or adjustments claims based on misrepresentation by the seller or performance variations resulting from installation related circumstances LA CROSSE TECHNOLOGY LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL CONSEQUENTIAL PUNITIVE OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION THIS PRODUCT IS NOT A TOY KEEP OUT OF CHILDREN S REACH This warranty gives you specific legal rights You may also have other rights specific to your State Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you For warranty work technical support or information contact La Crosse Technology 2809 Losey Blvd S 24 La Crosse WI 54601 Phone 608 782 1610 Fax 608 796 1020 e mail support lacrossetechnology com warranty work sales lacrossetechnology com information on other products web www lacrossetechnology com FCC ID OMO 01RX WEATHER STATION OMO 01TX SENSOR THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION 25
Download Pdf Manuals
Related Search