Home

Krell Industries KRC-HR User's Manual

1. Pin 3 Inverting The RCA center conductor for each channel is wired in parallel with pin 2 Only one of the preamp outputs should be connected to an individual amplifier They can be used simultaneously to drive amplifiers in two different systems When connecting inputs or outputs to the KRC HR remember that the balanced connections will have 6dB more gain than the single ended connections When level matching is critical in your installation keep this specification in mind REAR PANEL DESCRIPTION INPUTS Four single ended inputs via standard RCA connectors PH Line level input if phono board is not installed S 2 S 3 S 4 Two balanced inputs via standard XLR connectors B 1 B 2 Tape input via standard RCA connectors MAIN OUTPUTS Single ended RCA output connectors Balanced XLR output connectors Balanced XLR output pin configuration Pin 1 Shield ground Pin 2 Non inverting hot Pin 3 Inverting TAPE OUTPUT Record output via RCA connectors BASIC PREAMPLIFIER OPERATION The KRC HR has the flexibility of a remote controlled device but does not require special attention in order to perform simple functions The KRC HR will function much like other KRELL preamplifiers The unit can be operated from the front panel controls or via the remote control All functions available on the front panel can also be accomplished from the KRC HR remote control This provides the ability to sit in your favorite listening pos
2. 2 5 3 5 4 B 1 B 2 FUNCTIONS TAPE PHASE GAIN MUTE L BALANCE R BALANCE VOLUME FRONT PANEL DESCRIPTION Selects phono input line level input when phono board not installed Selects S 2 input selects 5 3 input Selects 5 4 input Selects B 1 input Selects B 2 input Selects tape input and allows monitoring of tape return Inverts absolute polarity of the main output 180 degrees LED illuminates when polarity is reversed Low 6dB High 12dB LED illuminates in High position No signal output when LED is on Left channel attenuation in 1 dB increments and OFF Right channel attenuation in 1 dB increments and OFF Stepmotor driven optical encoder REMOTE CONTROL 1 When a function button on the remote control is pressed and held the blue pilot LED will flash on the KRC HR When the button is released the flashing stops This indicates that the KRC HR has received a command 2 The functions of the remote control are identical to the front panel functions BATTERY INSTALLATION Batteries should be replaced when the KRC HR functions from the remote control become intermittent 1 Remove the four hex head screws from the back of the control with the T 10 torx supplied 2 Remove the back plate to expose the battery storage compartment 3 Replace batteries Refer to the polarity markings while inserting the batteries for proper installation 4 Replace the back plate and insert the four hex head scre
3. flashing blue power LED should now stop flashing and the unit should follow the standard turn on sequence If the unit does not perform in this manner contact your dealer or KRELL 11 QUESTIONS AND ANSWERS Q A When I turn up the volume on the KRC HR a loud hum is present from the loudspeakers What could this be Hum can be caused by several different disturbances Check to make sure that all of the cables in and out of the KRC HR are sound and making proper contact Make sure that there are no power supplies or hum inducing components on top of or directly below the KRC HR You could also be experiencing a ground loop in the system Put a 3 prong to 2 prong AC adaptor cheater plug on the KRC HR power cord The hum should go away You may also need to float ground on other system components if the hum remains Please contact your dealer or the product manufacturer before a non KRELL component s ground is lifted Remember to always keep at least one component grounded If these suggestions do not lead to a solution please consult your dealer or KRELL Can the KRC HR be used to control more than one system Yes the KRC HR has both single ended and balanced outputs that can be used simultaneously to control two different systems but both systems will play from the same input at identical volume settings When I select the B 1 input on the KRC HR one channel seems to have less gain than the other Is s
4. RELL The Leader in Audio Engineering KRC HR PREAMPLIFIER m OWNER S REFERENCE A T 37 OF CONTENTS 10 11 12 14 15 INTRODUCTION UNPACKING THEATER THROUGHPUT SETUP BASIC INSTALLATION INPUT OUTPUT CONNECTIONS REAR PANEL DESCRIPTION BASIC PREAMPLIFIER OPERATION FRONT PANEL DESCRIPTION REMOTE CONTROL PROTECTION CIRCUITRY INDICATORS QUESTIONS AND ANSWERS SPECIFICATIONS WARRANTY AND SERVICE INTRODUCTION Thank you for your purchase of the KRELL KRC HR remote control preamplifier The KRC HR combines refinements of the original KRC with a radical approach to volume control circuitry The HR designation signifies HIGHEST RESOLUTION due to the substantial improvement in sonic quality provided by our most sophisticated electronic volume control The unit also has a Theater Throughput which allows easy installation of the unit within a home theater system Please see page 4 for details on setting the KRC HR for the Theater Throughput function prior to installation To obtain the best performance from your KRC HR careful attention should be paid to its placement installation and operation A thorough understanding of these details will help insure satisfactory operation and a long life for the KRC HR and related system components i This Owner s Reference is divided into several sections each designed to perform a different function As you read through the Owner s Reference you will become bet
5. RELL In the event adequate proof of purchase date is unavailable the warranty period will begin on the date the unit was originally shipped from the factory The original ship date can be determined by KRELL from the serial number The warranty for KRELL products is valid only in the country to which they were originally shipped through the authorized KRELL Distributor for that country and at the factory There may be restrictions on or changes to KRELL s warranty because of regulations within a specific country Please check with your Distributor for a complete understanding of the warranty in your country Freight to the factory is your responsibility Return freight within the United States is included in the warranty If you have purchased your KRELL product outside the United States and wish to have it serviced at the factory all freight and associated charges to the factory are your responsibility Krell will pay return freight to the US based freight forwarder of your choice Freight and other charges to ship the unit from the freight forwarder to you are also your responsibility The operating voltage of this unit is determined by the factory and can only be changed by an authorized KRELL Distributor or at the factory The voltage for the KRC HR in the USA can not be changed for six months following the original purchase date Any unauthorized voltage conversion disassembly component replacement perforation of chassis updates
6. TECTION CIRCUITRY section of this manual for more information 6 The power up sequence lasts about 15 seconds Once completed the KRC HR can be operated from the front panel or the remote control INPUT AND OUTPUT CONNECTIONS CAUTIONS When making connections to this component or any other make sure that the power amplifier is OFF Make sure all cable terminations are of the highest quality free from frayed ends shorts or cold solder joints 1 Connect the left and right inputs of your source equipment to the inputs on the KRC HR The KRC HR is equipped with 4 single ended inputs 2 balanced capable inputs and 1 single ended tape input 2 If the optional phono card is included in your KRC HR the turntable s phono leads will be connected to the PH input If the phono card is not in the KRC HR the PH input remains a standard line level input 3 If the Theater Throughput option is to be used connect the Main L R outputs of the A V surround processor to the S4 input When S4 is selected the KRC HR will act as a unity gain throughput no change in level for this input All control of level will now be performed by the A V surround processor 4 Connect the main output of the KRC HR to the input of your power amplifier The KRC HR has both balanced outputs via XLR connectors and single ended outputs via RCA connectors The pin assignment for the XLR inputs and outputs are Pin 1 Shield ground Pin 2 Non inverting hot
7. e hum into the phono stage 2 Place the power supply in a location away from hum sensitive components such as turntables or phonostages Connect the male end of the DC power cable into the computer type connector on the back of the supply DO NOT PLUG THE POWER SUPPLY INTO THE AC OUTLET AT THIS TIME 3 Connect the female end of the DC power cable to the computer type connector on the back of the KRC HR CAUTION ALWAYS CONNECT THE DC CABLE TO THE BACK OF THE KRC HR AND TO THE POWER SUPPLY BEFORE YOU PLUG THE POWER SUPPLY INTO THE WALL OUTLET FAILURE TO FOLLOW THE CONNECTION SEQUENCE WILL CAUSE DAMAGE TO THE KRC HR 4 Plug the AC cord into the receptacle on the back of the power supply Plug the remaining end into the wall AC receptacle NOTE While the KRC HR has superb regulation and does not require a dedicated AC circuit we strongly advise against any connections through extension cords or multiple AC adaptors High quality 15 amp line conditioners or grounded AC strips are acceptable 5 When the KRC HR power supply is plugged into the wall AC outlet the preamplifier will go through its power up sequence a The volume control will automatically rotate to the Off position fully counterclockwise b The Select section LEDs on the KRC HR will remain unlit until an input or function is selected c The Protection relays will open once the monitoring circuits have determined there are no input or output disturbances See the PRO
8. f when you replace the fuse the unit powers up and shuts off shortly thereafter call the factory When I push the function buttons on the KRC HR remote control the preamp does not respond What should I do Check the batteries and change them if necessary The selected input button on the KRC HR is blinking on and off I cannot stop the blinking nor can I play music What is wrong That selected input has developed a problem causing the KRC HR to disable that input After correcting the problem the unit will return to normal Refer to the section on Protection Circuitry Page 11 for a more detailed explanation SPECIFICATIONS GAIN 6dB or 12dB SIGNAL TO NOISE 96dB unweighted THD 1KHz less than 01 20KHz less than 01 INPUT IMPEDANCE 47 000 Ohms 47K Ohm OUTPUT IMPEDANCE 5 Ohms OUTPUT VOLTAGE 14 volts R M S DIMENSIONS Unit 19 0 Wide 14 5 Deep 2 75 High with feet Power Supply 11 Wide 9 Deep 2 5 High All operational features functions and specifications and policies are subject to change without notification 14 THERE ARE NO USER SERVICEABLE PARTS INSIDE ANY KRELL PRODUCT The KRELL KRC HR has a limited and transferable warranty of five years for parts and labor The warranty period begins on the date of retail purchase as noted on the retail sales slip provided by an authorized KRELL Dealer or Distributor or on the warranty registration card sent to K
9. ition while controlling all system start up preamplifier functions Press the Mute button on the KRC HR Turn the volume control fully counterclockwise to the OFF position Turn the power amplifier ON A OW N m Choose a listening source and select that input by pushing the corresponding input button on the KRC HR 5 Start play of the source 6 Turn the volume control clockwise until you reach a comfortable listening level 7 When changing sources return to the Mute position and or lower the volume This insures that the next source you play will not be potentially damaging to your system with a high output level THEATER THROUGHPUT The S4 input of the KRC HR can be set to operate as a unity gain stage This removes the KRC HR volume control from the signal path Volume control is then transferred from the KRC HR to an A V surround processor connected to the S4 input This feature greatly simplifies the installation of a surround sound processor into a high performance audio video surround system If the Theater Throughput option is activated select S 4 when your home theater surround system will be used In this mode all control of volume is performed by the A V surround processor connected to that input Specifically Level Balance and Gain are disabled on the KRC HR for the S 4 input only when the Theater Throughput is engaged Mute and Tape monitor input will function normally INPUT SELECTION PH S
10. omething wrong with the preamp Probably not The balanced input or output internal cable terminals could be attached incorrectly Locate the channel that appears to have less gain Switch the cable connected to that channel s input to the other channel and vice versa to determine whether a cable is defective If there is no difference in level do the same thing at the output of the KRC HR If the problem is not the cable check to make sure that the input and output connections are connected at the correct locations on the preamp There should be no LEDs illuminated in the Balance control section of the front panel indicating a level imbalance 12 gt gt gt gt Why do I have to turn up the volume so high to get music at a normal listening level If your system does not seem to have enough gain you are probably not using the balanced input and output capabilities of the KRC HR Each balanced termination has 6dB more gain than a single ended termination More important however is that the balanced lines provide superior sonic quality If you must use single ended terminations use the High gain setting which has 6dB more gain than the Low position The pilot LED in the KRC HR and its power supply are not illuminated What should I do Check the fuse in the back of the power supply If there is a break in the wire inside the fuse replace it If there is no break in the fuse call your dealer or KRELL I
11. or modifications performed to the unit will void the warranty 15 WARRANTY AND SERVICE msme KRELL is not responsible for any damage to units incurred in transit If any shipping damages are incurred during transit of your units to the factory you must initiate filing of the insurance claim Likewise KRELL will file claims for shipping damages incurred during transit of your units from the factory to you The use of any packing material other than original is not recommended KRELL may at its discretion pack a unit in new material for the return shipment Krell will bill you for such if the unit was shipped in non standard packing or if the original packing is so damaged as to be unuseful Should you need to purchase additional packaging please contact your authorized KRELL Dealer Distributor or KRELL for assistance IMPORTANT If you think there are problems with your unit please contact your Dealer Distributor or the factory immediately Do not return any unit to KRELL for repair without first calling to discuss the problem and obtaining a Return Authorization number All operational features functions and specifications and policies are subject to change without notification 16 KRELL 45 Connair Road Orange CT 06477 3650 USA 203 799 9954 Fax 203 799 9796 1997 by Krell Industries Inc All rights reserved P N 1960602000023
12. ter acquainted with the features and functions that make the KRC HR a superb value A Question and Answer section is included where answers to common questions are provided If you have any questions or suggestions please do not hesitate to contact your authorized dealer or the KRELL staff for assistance In the unlikely event that your KRC HR requires service you will be pleased to know that it is backed by a comprehensive Customer Satisfaction policy and one of the most advanced service facilities in the industry For detailed information on the terms and conditions of service please consult your warranty registration card or contact your authorized KRELL Dealer or Distributor UNPACKING 1 Open the box and remove the top layer of foam 2 Remove the KRC HR and the foam tray surrounding it The following items will now be visible KRC HR power supply KRC HR remote control 8 ft DC power cable T 10 torx for remote T 15 torx AC power cord p ee ee ee If any of these items are not included please contact your authorized dealer immediately for assistance 3 Remove from the plastic bags the preamplifier power supply remote control and power supply cable connectors NOTE Save all packing materials If you must ship your KRC HR in the future repack the unit with the power supply and remote control in its original packing to prevent damage in transit CAUTION Do not connect the power cord from the power supply in
13. to the AC mains before completing the Installation section THEATER THROUGHPUT SETUP NOTE If the KRC HR must be handled after the top cover has been removed the unit must be held only on the sides of the chassis Never move the KRC HR while the top cover is off by holding the front panel When reinstalling the top cover insert the four screws into the chassis sides first and lightly tighten them Install the screws in the top surface and tighten them lightly Then tighten all screws firmly starting with the side screws and finishing with the top screws SETTING THE 64 INPUT FOR THROUGHPUT FUNCTIONS This procedure should be done with the unit OFF a Remove the KRC HR top cover screws with the T 15 Torx wrench supplied b Locate the switch towards the front of the board that is labeled S4 Proc Set the dip switch to the proc processor position NOTE The default position of this switch sets the S4 input for standard operation In this position S4 is identical to the S1 S2 and S3 inputs c Place the top cover back on the KRC HR and insert the cover screws BASIC INSTALLATION 1 Place the unit on a firm level surface free from excessive dirt or moisture The KRC HR is not particularly hum sensitive allowing other components to be placed on or around it If the optional phono card is installed in the KRC HR some components such as Digital to Analog converters power supplies or components with motors can induc
14. ws 10 The KRC HR is the first high end preamplifier to have protection circuitry at the input and output The indicators on the KRC HR which are described below will give you a general location of a problem in your audio system l LO When the KRC HR s monitoring circuitry recognizes excessive DC levels at one of the inputs the output disconnects from the front end circuits and the LED corresponding to that input will flash repeatedly until the problem is removed If you try to select that input the preamplifier will not respond to the command To check the input remove the cables corresponding to the flashing input and inspect them with an ohm meter The flashing LED should become steady within 5 seconds of removing the suspect input If the cabling appears to be sound try another source component into the suspect input If the KRC HR LED continues to flash unplug the unit and contact your dealer or KRELL If the problem ceases have the component originally connected to that input checked out at your dealer or at the factory If the KRC HR s monitoring circuitry recognizes a short at the output the output disconnects from the front end circuitry the DC voltage to the preamplifier s circuits disconnects and the blue power LED flashes Remove and check all the cabling and components connected to the KRC HR Unplug the KRC HR from the AC wall socket Wait for one minute and plug the unit back into the AC wall socket The

Krell Industries KRC-HR User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents