Kramer Electronics RC-53D User's Manual
Contents
1. Grounding Connection Components To ground the RC 53DLC 1 Connect the Ring Tongue terminal to the building grounding point wire it is recommended to use a green yellow AWG 18 0 82mm wire crimped with a proper hand tool 2 Insert the M3x6 screw through the toothed lock washers and the tongue terminal in the order shown above 3 Insert the M3x6 screw with the two toothed lock washers and ring tongue terminal into the grounding screw hole and tighten the screw Using the RC 53D K NET Auxiliary Control Panel 5 Using the RC 53D K NET Auxiliary Control Panel The installation process is not detailed in this user manual This user manual is applicable once the unit is installed and configured and includes e Setting up the labels on the buttons according to your specific requirements e Configuration of the Master room controller via the K Config Windows based configuration software Since the auxiliary panel is used as a remote controller for Master Room Controllers via the proprietary communication channel K NET as illustrated in Figure 4 e I trequires only a K NET connection to the Master Room controller e power supply unit is not required e The auxiliary panel can be programmed only via the Master Room controller for example the Kramer SV 551 SummitView Processor Switcher PINOUT GND Black B White A Green V 12 Red Figure 4 RC 53D connected to the SV 551 SummitView Proces2. SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 82301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction K For the latest information on our products and a l
3. please check our Web site for the most current and accurate warranty information Whois Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What Kramer Electronics will do Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty 1 Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during ship
4. terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreasonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons equipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last Seven years as of this printing
5. Kramer Electronics Ltd USER MANUAL Model RC 53D K NET M Auxiliary Control Panel RC 53D Quick Start Guide a This guide helps you install and use your product for the first time For more detailed information go to http www kramerelectronics com support product downloads asp to download the latest manual gt or scan the QR code on the left Step 1 Check what s in the box A RC 53D 1 Quick start guide Screwdriver Step 2 Connect the RC 53D Connect a master room controller to one of the K NET terminal block connectors Optionally connect another auxiliary device to the other K NET terminal block connector Note that the RS 232 port is for factory use only Step 3 Configure the system Set up the labels on the buttons and configure the system via the K Config software using the Master room controller Step 4 Install the RC 53D Mount the RC 53D in a suitable wall box Contents Contents 1 Introduction 2 Getting Started 2 1 Achieving the Best Performance 2 2 Safety Instructions 2 3 Recycling Kramer Products 3 Overview 4 Defining the RC 53D 4 1 Grounding the RC 53D 5 Using the RC 53D K NET Auxiliary Control Panel 6 Installing the RC 53D Faceplate Button Caps and Labels 7 Operating the RC 53D K NET Auxiliary Control Panel 8 Technical Specifications Figures Figure 1 RC 53D K NET M Auxiliary Control Panel Front Panel Figure 2 RC 53D K NET
6. M Auxiliary Control Panel Rear Panel Figure 3 Grounding Connection Components Figure 4 RC 53D connected to the SV 551 SummitView Processor Switcher Figure 5 Sample Button Label Sheet Figure 6 Button Cap Orientation Figure 7 Inserting the Label Figure 8 Placing the Button Cap Figure 9 RC 53D Labels Setup Tables Table 1 RC 53D K NET Auxiliary Control Panel Front Panel Features Table 2 RC 53D K NET Auxiliary Control Panel Rear Panel Features Table 3 Grounding Component Descriptions Table 4 The Commands Configuration Table 5 Technical Specifications of the RC 53D K NET Auxiliary Control Panel cow 4 OW NNN E E tA SW gt Introduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Congratulations on purchasing your Kramer RC 53D K NET M Auxiliary Control Panel which is available in European 80mm and 86mm height versions and American versions and can be used as a system controller when connected via K NETTX to a Master room cont
7. ctronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
8. ed labels from the supplied button label sheet 2 Hold the button cap so that it is oriented as shown in Figure 6 with the wings on the left and right sides Figure 6 Button Cap Orientation Figure 7 Inserting the Label 3 Insert the label inside the cap 4 Repeat for all six caps Installing the RC 53D Faceplate Button Caps and Labels 5 Retaining the orientation place the six button caps on the buttons of the RC 53D Ww Figure 8 Placing the Button Cap 6 Remove the protective foils from both sides of the Perspex acrylic glass windows 7 Remove the protective foils from both displays 8 Place the faceplate on the RC 53D so that the four screw mounting holes are aligned 9 Insert the four mounting screws and tighten with a screwdriver 10 Install the volume control knob KRAMER SIMPLE CREATIVE TECHNOLOGY Operating the RC 53D K NET Auxiliary Control Panel 7 Operating the RC 53D K NET Auxiliary Control Panel In the following example illustrated in Figure 9 the auxiliary control panel is labeled with specific functions and each button is programmed to perform several tasks as defined in Table 4 Table 4 The Commands Configuration The Label The Macro Sequence Power up the projector Power up the DVD player Roll down the projector screen 1 minute delay for the projector to heat up The projector selects the DVD input KRAMER e Figure 9 RC 53D Labe
9. ist of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Caution Safety Warning Disconnect the unit from the power supply before opening servicing P N 2900 000567 Rev 4 Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000567 REV 4
10. ls Setup Power down the projector Stop the DVD player Power down the DVD player Stop the Power down the VCR Roll up the projector screen Stop the video player The projector selects the DVD input Play the DVD Stop the DVD The projector selects the VCR input Play the VCR VOLUME e Use the VOLUME knob to adjust the audio level 1 This is only one example among numerous possibilities each button can be programmed as required In this example two buttons are not assigned 2 By the technical installer 3 A macro sequence including several commands per button carried out one after the other Technical Specifications 8 Technical Specifications Table 5 defines the technical specifications Table 5 Technical Specifications of the RC 53D K NET Auxiliary Control Panel PORTS 2 K NET on terminal block connectors 1USB connector 1 RS 232 on terminal block connector factory use only POWER SOURCE 12V DC 140mA over K NET FUSE 500mA FSMD 1812 DIMENSIONS For the USA 11 4cm x 2 6cm x 11 4cm 4 49 x 1 02 x 4 49 W D H For Europe 15 2cm x 1 9cm x 8 6cm 5 98 x 0 75 x 3 39 W D H or 15 2cm x 1 9cm x 8cm 5 98 x 0 75 x 3 15 W D H WEIGHT 0 14kg 0 311bs approx ACCESSORIES 1 Specifications are subject to change without notice 10 KRAMER SIMPLE CREATIVE TECHNOLOGY LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the
11. ment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a return authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product If it is decided that this product should be returned directly to Kramer Ele
12. n indicating volume ev Figure 2 and Table 2 define the RC 53D rear panel Version for the US Version for Europe RS232 KNet KNET GND Rx Tx GND B A 12V GND B A 2V olla oroo ex 9l lobolo esa o Figure 2 RC 53D K NET Auxiliary Control Panel Rear Panel Table 2 RC 53D K NET Auxiliary Control Panel Rear Panel Features Program USB Connector Connect to a computer for firmware upgrade Grounding Screw Connect to grounding wire RS 232 Terminal Block For factory use only K NET Terminal Block Connect the GND to the Ground connection connect B and K NET Terminal Block A to RS 485 and connect 12V to 12V on the companion unit 1 By the system integrator only 2 When the unit is connected via K NET to a Master Room Controller you can upgrade the firmware via the USB or ETH ports of the Master Room Controller 3 The ground connection is sometimes connected to the shield of the RS 485 cable in most applications it is not connected 4 KRAMER SIMPLE CREATIVE TECHNOLOGY Defining the RC 53D 4 1 Grounding the RC 53D The grounding screw is used to earth the chassis of the unit to the building ground preventing static electricity from impacting the performance of the unit Figure 3 and Table 3 define the grounding screw components Table 3 Grounding Component Descriptions ra Component Description M3X6 screw 1 8 Toothed Lock Washer M3 Ring Tongue Terminal Figure 3
13. ommend Kramer high performance high resolution cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Do not secure the cables in tight bundles or roll the slack into tight coils e Avoid interference from neighboring electrical appliances that may adversely influence signal quality e Position your Kramer RC 53D away from moisture excessive sunlight and dust This equipment is to be used only inside a building It may only be connected to other equipment that is installed inside a building Safety Instructions Caution operator serviceable parts inside the unit Warning Use only the Kramer Electronics input power wall adapter that is provided with the unit Warning Disconnect the power and unplug the unit from the wall before installing Recycling Kramer Products The Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and will cover any costs of treatment recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility For details of Kramer s recycling arrangements in your particular country go to our recycling pages a
14. roller for example the SV 552 SummitView Processor Switcher or one of the Kramer SL series controllers 2 Getting Started This user manual is written for the end user Refer to the separate K Config Configuration Guide available online for details of how to install and configure the Room Controller We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual user manuals application programs and to check if firmware n Go to http www kramerelectronics com to check for up to date upgrades are available where appropriate GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Routers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 K NET is a proprietary Kramer protocol for communication between Kramer products 3 The guide provides information about how to set up the system and is updated on a regular basis For the latest online guide go to http www kramerelectronics com 1 Getting Started 2 1 2 2 2 3 Achieving the Best Performance To achieve the best performance e Use only good quality connection cables we rec
15. sor Switcher 1 By authorized Kramer technical personnel or by an external system integrator 2 Power supplies are sold separately Consult your Kramer dealer for details 6 KRAMER SIMPLE CREATIVE TECHNOLOGY Installing the RC 53D Faceplate Button Caps and Labels 6 Installing the RC 53D Faceplate Button Caps and Labels This section describes how to install the faceplate button caps and labels Figure 5 illustrates a sample button label sheet iIKRAMER co l l 1 e a MODE MUTE SYNC FREEZE AUTO BLANK 5 EL ECTFOIPICE 4 5 7 8 9 0 TAKE MENU RES IMAGE RESET SCAN LAPTOP LAPTOP BIINDB BLINDS SCREEN SCREEN pt 1 pc 2 VERI VERE DDA Hoa sate ALL ALL zoom Zoom on OFF 1 DUT T TURN SCALER SCALER MATRIX auno TURN b 3d v VER BATELLITE LEPTOP ED PLAYER RADIO MATRIX PROJ PROJ TAPE TAPE SOURCE SOURCE m m ren CAMPRA WHS men RECEIVER TV TENER Doc CAM ACCEPT ACCEPT aux nal ews E s VIDEO marin d pm Em fe deu s W1 Y ER 4 vuv 2 RGB 1 AGB 2 5 RGBHV RGBHV vnega 1 2 CAM CAME PP 1 4 4 TUNER TUNER LIGHTS LIGHTS RADIO1 RADIO sa re AFV PLAY STOP voL VOL LOCK ON OFF SWITCH M pow FOCUS Figure 5 Sample Button Label Sheet To install the faceplate button caps and labels 1 Remove the requir
16. t Attp www kramerelectronics com support recycling KRAMER SIMPLE CREATIVE TECHNOLOGY Overview 3 Overview The RC 53D is an auxiliary remote control panel for Master Room Controllers for control of A V equipment in a room The RC 53D e Features six front panel single color backlit buttons designed in two groups one group of two buttons and another group of four buttons e Hasadigital volume control adjustment knob e s available as a 2 Gang wall plate for the USA or a 2 Gang wall plate for Europe e Does not require a separate power supply e Includes an RS 232 serial port e Includes two K NET ports and a USB port for firmware upgrade e Features two programmable LCD displays one for each button group 4 Defining the RC 53D Figure 1 and Table 1 define the RC 53D front panel Version for the US Version for Europe DISPLAY J o KRAMER KRAMER Figure 1 RC 53D K NET Auxiliary Control Panel Front Panel 1 Such as the Kramer SummitView System or the SL 1 Master Room Controller 2 Available in two height sizes 8 6cm and 8cm 3 Defining the RC 53D Table 1 RC 53D K NET Auxiliary Control Panel Front Panel Features SOURCE Buttons Group of four programmable backlit buttons Faceplate Screws Four screws connecting the faceplate to the Rear Box DISPLAY and SOURCE Programmable 8 character LCD displays on a blue background Labels 6 VOLUMELEDs Light gree
Download Pdf Manuals
Related Search