Koss JR170 User's Manual
Contents
1. outlet Also required 2 AA batteries in the headset 2 Connect Transmitter to Audio source a Connect one end of the Dual RCA Cable to your audio source s left and right audio output jacks Note If there are no fixed level audio outputs on the audio source connect the cable to to variable level Hi Fi audio outputs or 9 29 2011 10 43 AM 2 of 3 http koss com koss kossweb nsf pmbyunid E7D4 1 35ED2903AFF86257 refer to Line 3 for Y adapter connection instructions b Connect the other end of the Dual RCA Cable to the Left Right Audio Input Jacks on the transmitter WARNING DO NOT connect the Dual RCA Cable to the speaker terminals of the TV or Audio Source This may damage your transmitter and or your audio source 3 If no Audio Output Jacks are available Connect to headphone Jack using Y Adapter Cable and Dual RCA patch cord both included a Connect the color coded left white and right red ends of the Dual RCA Cable to the Y Adapter Cable b Connect the 1 8 headphone plug on the Y Adapter Cable to the headphone input jack located on your audio source If your audio source requires a 1 4 headphone plug you will require a Headphone Jack Adapter Plug not included then insert into your source s headphone output jack c Connect the other end of the Dual RCA Cable to the Left Right Audio Input Jacks on the rear of the transmitter Operation 1 Transmitter Operation and Adjustment a Turn on pow2. 1 of 3 http koss com koss kossweb nsf pmbyunid E7D4 135ED2903 AFF86257 Print Close This Window Components The JR170 RF wireless stereophone includes the following components 1 Transmitter 2 Headphone 3 Headphone Power LED 4 Power On Off 5 Battery Door 6 Volume Control 7 Channel Selector 8 Channel Indicator LED 9 Transmitter Power LED 10 Transmitter Power On Off amp Channel Selector Insert Batteries 1 Locate the battery door on the left earcup 2 To open the battery door press the area at the top of the door about an inch above the Koss Logo and push and slide the door down from the headband 3 Insert 2 AA batteries 4 Slide battery door back into place Turn on wireless operation 1 Locate the power on off switch on the left earcup 2 Slide switch to on 3 The LED will be red when the unit is powered on 4 The green Channel Indicator LED will light when a signal is received Set Volume Control 1 Locate the volume control on the bottom of the right earcup 2 Adjust the volume to a comfortable setting Trouble Shooting Guide No sound from the stereophone Check that the unit is on Check that the stereophone batteries are fresh and inserted in the correct direction Adjust volume control Distortion background noise Verify you are on the correct channel Check batteries Hookup amp Operation Transmitter Hookup 1 Connect AC Adapter to the transmitter and wall
3. er to your audio source TV Portable Device etc to which the transmitter is connected NOTE If transmitter is connected to the audio variable level outputs adjust the volume of the source TV etc to desired listening level If transmitter is connected to fixed level outputs no volume adjustment is needed b Adjust the Power On Off Switch to channel 1 or 2 choose the same channel as the channel selected on the headphones 2 Headphone Operation and Adjustment a Insure that you have inserted 2 AA batteries in the headphone battery compartment b Turn On Off Switch to the On position Power indicator on headphones should light up c Adjust Channel Selector to match channel selected on the transmitter Stand 10 15 feet away from the transmitter d Place headphones over your ears and adjust volume to your desired listening level NOTE If signal interference occurs adjust the channel selection on both the headphone and transmitter 3 To preserve your batteries and electricity when not in use turn the Power Switch to the Off position on the headphones and transmitter FCC Compliance Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Warning Part 15 21 Changes or modifications not e
4. xpressly approved by the party responsible for the compliance could void the user s authority to operate the equipment 9 29 2011 10 43 AM http koss com koss kossweb nsf pmbyunid E7D4 135ED2903 AFF86257 Industry Canada The term IC before the certification registration number only signifies that the Industry Canada technical specifications were met JR170_Sidel_English pdf 3 of 3 9 29 2011 10 43 AM
Download Pdf Manuals
Related Search