Kompernass KH 3006 User's Manual
Contents
1. 360 Line Laser KH 3006 Operating Manual KOMPERNASS GMBH BURGSTRASSE 21 D 44867 BOCHUM www kompernass com ID Nr KH3006 04 07 V2 KH 3006 360 Line Laser KH 3006 Read the operating instructions carefully before using the appliance for the first time and preserve this booklet for later reference Also give these operating in structions to whoever might acquire the appliance at a future time Safety instructions A Risk of personal injury e Keep and store the appliance out of the reach of children This laser appliance contains a Class 2 Laser NEVER direct the laser beam at people or animals NEVER look directly into the laser The laser beam can cause serious eye damage e Do NOT direct the laser beam at strongly reflective material Reflected laser beams are also dangerous In the event of the batteries leaking acids wear protective gloves There is a risk of receiving chemical burns A Beware of appliance damage e NEVER subject the appliance to rain Do not use the appliance in wet or moist environments e Do not use the appliance at locations where there is a danger of fire or explo sion e g in the vicinity of inflammable liquids or gases e All adjustments intended to increase the laser power are forbidden e To avoid damage to the appliance arrange for repairs to be carried out only by our Customer Services Depart ment or qualified specialists e Regularly check2. Storage Keep the fastening pins in the recesses provided on the sides of the appliance If you are not going to use the appliance for a long period remove the batteries from the battery compartment and store them seperately Disposal A Do not dispose of the appliance in your normal domestic waste Dispose of the appliance through an approved disposal centre or at your community waste facility Observe the currently applicable regula tions In case of doubt please contact your waste disposal centre Disposal of batteries Do not dispose of batteries with household waste All consumers are legally obliged to dispose of batteries at a collection site in their community city district or at a retail store This obligation is intended to ensure that batteries are disposed of in an environ mentally safe fashion Only dispose of batteries when they are fully discharged Dispose of the packaging materials in an environmentally responsible manner Warranty and Service The warranty conditions and the service address can be found on the supplied warranty card Importer KOMPERNASS GMBH BURGSTRASSE 21 D 44867 BOCHUM www kompernass com
3. the condition of the batteries Leaking batteries can cause damage to the laser appliance e If you do not intend to use the laser appliance for an extended period remove the batteries e Always change all batteries at the same time and always use batteries of the same type e Clean the battery compartment with a dry cloth e No liabilty will be accepted for damage resulting from manipulation to the laser equipment as well as from disregarding these safety instructions Intended use The appliance is intended for use in making alignments and determining angles in domestic construction work The appliance is intended for domestic purposes only not for commercial purposes Items supplied e Laser appliance with rotating plate e 2 Batteries 1 5 V Type AAA LRO3 e Operating instructions e Warranty card Technical Data Power supply 2 Batteries 1 5 V Type AAA LRO3 Measurement accuracy 6 35 mm over 5 meters Laser class 2 lt 5 mW A 650 nm Appliance description O Laser appliance O ON OFF button O Spirit level for horizontal lines Spirit level for vertical lines O Laser lens O Rotating plate with degree scale O Marking arrow O Fastening pins O Fixing points on the laser appliance O Fixing points on the rotating plate O Battery compartment on the rear side Inserting the batteries 1 Open the battery compartment O 2 Insert two batteries of Type AAA LRO3 into the battery compartment Comply
4. with the polarity markings in the battery compartment 3 Close the battery compartment Utilisation Switching On and Off 1 To switch the laser appliance on press the ON OFF button 2 To switch the laser appliance off press the ON OFF button once again Utilisation on a wall 1 Remove the laser appliance from the rotating plate The laser appliance clings to the rotating plate magneti cally 2 Place the rotating plate at the posi tion on the wall from where you wish to draw the alignment line 3 Secure the rotating plate to the wall in that you take both fastening pins from the sides of the appliance and you press them through the fixing points on the rotating plate and into the wall See Fig O Notice The fastening pins can be inserted into most upper surfaces such as wood plaster or mortar Alternatively espe cially with other upper surfaces you could also use adhesive tape for secu ring the rotating plate O You can also secure the laser appliance O without the rotating plate in that the fastening pins OQ are inserted through fixing points on the laser appliance O itself 4 Place the laser appliance O onto the rotating plate 5 Turn the laser appliance with the marking arrow into the desired direction 6 Switch the laser appliance on by pressing the ON OFF button The laser beam appears on the wall in the direction of the marking arrow P
5. lumb line To mark a plumb line turn the laser appliance on the rotating plate with the marking arrow pointing in the direction in which the laser marking is to be indicated then finely adjust it vertically with the spirit level Horizontal line To mark a horizontal line turn the laser appliance O on the rotating plate O with the marking arrow pointing in the direction in which the laser marking is to be indicated then finely adjust it horizontally with the spirit level O 1 Important The air bubbles in the spirit levels must be positioned between the two markings Angles 1 To mark an angle shift the zero marking of the degree scale to the marking arrow O on the laser appliance O Fig O Turn the laser appliance O from the start position Fig with the marking arrow Q to the desired angle e g 45 Fig Utilisation on the floor on the ceiling 1 Should you use the laser appliance O on the floor or on the ceiling secure it as described above if need be Turn the laser appliance O with the marking arrow in the desired direction Cleaning and Care A CAUTION Under no circumstances should the laser appliance be submersed in water or other fluids The appliance could be irreparably damaged Do not use aggressive detergents or solvents They could cause damage to the appliance e Clean all components of the appliance with a soft cloth Clean the laser optic with a soft brush
Download Pdf Manuals
Related Search