Kohler CFI230J User's Manual
Contents
1. plate anticlockwise from the full clockwise position until it clicks three times 4 ECO Water flows from the outer set of holes at a reduced flow rate To select the Economy setting turn the spray plate fully clockwise 12 CFi230 CLEANING The unit should be cleaned regularly Use a non abrasive cleaner ideally with a pH value of 4 to 8 NON applied with a soft cloth ABRASIVE CLEANER Under no circumstances should scourers or powerful detegents be used as these can damage the metallic p Ms E surface of the frame and also tarnish the glass coating i 4to8 9to14X To avoid limescale use your thumb or a soft cloth to wipe any limescale from the soft rubber nozzles and the front face of the showerhead CUSTOMER SERVICE Kohler Daryl and Kohler Mira We take the question of customer service seriously Consequently there is one initial point of contact Daryl Showering Technical Services 0151 606 5000 This team will ensure that the quality of support you require is provided by specialists appropriate to that field i e for matters relating to the shower enclosure you will be aided by Daryl Showering and for the shower system including the Digital Mixer your call will be supported by Mira Showers personnel Your contact for all queries is Daryl Showering Customer Services 0151 606 5000 If when you first use your shower it does not function correctly first contact your installer to check t2. CFI230J Indigo Quadrant Enclosure with integrated Mira Magna Shower System Slide Rail Fixed Head Kohler Daryl Limited Alfred Road Wallasey Wirral CH44 7HY England Tel 44 0 151 606 5000 Fax 44 0 151 638 0303 Fitti U 7 t ti www daryl showers co uk E ing ser ns a So o a k E mail Daryl daryl showers co uk Fit top cap Non Water delivery side Fit top cap Water delivery side Apply a thin bead of sealant along the outside edge of the wall channels Fit the door seal to the back edge of the door When the door is closed the edge of the seal should touch the side panel along it s length Do not use the enclosure for at least 24 hours 96 CFI230J Introduction The following pages aim to provide comprehensive installation instructions plus advice on how to care and maintain your product We recommend that the unit is installed by a qualified Plumber or Engineer Please retain this document for future reference Note Due to our desire to always improve our products Daryl reserve the right to change specification without prior notice N Safety Precautions Caution Care should be taken when drilling into walls and floors to avoid any hidden pipes or wires We strongly recommend that all glass panels are moved by a minimum of two people and that protect
3. FI230 15
4. e column Connect the water pipe to the connector from at the top of the column A Caution Support the weight of the column Plug the electrical cable into the connector on the cable from the Water Delivery System A Caution Push top of column into the wall jamb until it locks in place CFI230 DH Fit the Suppression Ferrite close to The Suppression Ferrite is packed with the Note Digital Mixer Slide Rail Water Delivery Only the Water Delivery connector See Step 42 for the Fixed Head Water Delivery Carefully lift the Water Delivery System column and place the bottom aa into the wall jamb Place the cable in the Be very careful not suppression ferrite Wrap to scratch or damage the cable around the cover and through the ferrite again and then close the cover until it snaps shut the tray Support the weight of the column Connect Push top of column the water pipe to the connector from at the top of the column J into wall jamb until it locks in place Plug the electrical cable into the connector 5 from the Water Delivery System at the top Caution 9 4 CFI230 of the column e S A n Li K r eo UM TEP 40 COMPONENTS Water Delivery Top Caps Re aa Roller Securing Ca
5. hat installation and commissioning are satisfactory and in accordance with the instructions in this manual If over time the performance of your shower declines consult this manual to see whether simple home maintenance is required Please call our Technical Services Department to talk the difficulty through request service under guarantees if applicable or take advantage of our after sales service CFI230 17 TROUBLESHOOTING The information below gives details on what you can do as a user should you encounter difficulties whilst operating the shower If there is a problem with the shower control some of the push buttons will flash very fast Malfunction Push buttons are Water supply isolated Check water supply flashing on the shower control and or the Damaged or broken cable Check cable connections shower will not operate connection Electrical supply isolated Check electrical supply Handset Adjustment or fuse blown To adjust the height of the handset press Digital Mixer Valve Isolate product and turn the release button A and slide the clamp breakdown back on after 30 seconds If the problem still persists note the sequence of the flashing push buttons and contact Customer Services bracket assembly up or down to the desired position The handset can be moved both vertically and horizontally until the desired position is reached B A friction mechanism in the clamp bracket wi
6. he blanking cap on the other side Push the roller onto the slot in the tray until it locks in place ensuring the plastic glass guide is retained inside the roller body Fit 4 x screws Carefully remove the Water Delivery System Slacken screws A Push the glass panel between Push the door stop vinyl into the track and from the Water Delivery Wall Jamb the wall jamb and the glass clamp The glass against the fixed roller except 800 should be 2mm lower than the top of the wall Carefully lift door into the enclosure jamb Tighten screws A when the glass is in Important Requires a minimum of 2 people Caution 8 CFI230J CFI230J 2 1 Remove the lintel from glass and remove the parking block Carefully lift the assembly onto the tray The end Adjust wall jamb until glass is parallel to the a of the glass panel fits into slot A on the tray edge of the tray A and vertical at B 1 Match parking block 2 Spot drill hole positions 3 Drill holes with 6mm drill The wall channel end sits on the flat section of to mark on wall the tray B a Pa E gt z 4 Plug holes 5 Screw parking block to wall 6 Re fit lintel to glass ee i in wa and push wall m
7. hould be equally spaced on each panel Re tighten screws loosen the 4 screws C and move the panel until A i it is the correct postion Re tighten screws Note The lintel is supplied as a RH unit lt For LH versions loosen the panel clamps and turn them through 180 Check end of glass is vertical Ensure glass panels are parallel to each other If the any further adjustment is required to make Measure the distance of the glass between Check top rail is level Draw around parking block the glass panel vertical turn the 4 screws D the wall jamb and the tray A Cut the until the panel is in the correct position splashguard to size cutting at the wall jamb end Fit the splashguard to the bottom of the glass 10 CFI230J CFI230J 19 The Daryl Care Programme Keeping your enclosure beautiful throughout its lifetime is easy with products from the Daryl care programme Using state of the art bespoke machinery combined with the latest technology all Daryl doors and panels are coated with a glass protector in highly controlled factory conditions The protector acts as an invisible barrier on the glass to prevent build up of limescale soap scum stains and dirt The factory appl
8. ied protector will last from months to years depending on use and the hardness of water in your area It will never crack peel discolour or build up Coated surfaces are kept clean simply by rinsing or wiping with a damp cloth and regular use of Daryl Glass Cleaner There are two separate elements to caring for your Daryl shower door enclosure or bath screen _ Daryl Glass Cleaner for the regular cleaning of your shower door enclosure or screen N Daryl Care Kit comprising of Glass Treatment and Glass Protector suitable for use where glass protector has not already been applied or for topping up factory coated protector Daryl Glass Cleaner For occasional cleaning of glass treated with Daryl Glass Protector or for more regular maintenance of untreated surfaces we recommend using Daryl Glass Cleaner The Cleaner cleans and polishes without smearing or streaking and rejuvenates the Glass Protector Daryl Glass Treatment and Daryl Glass Protector Available in one care kit the Treatment and Protector are used on new or existing shower installations where Protector has not already been applied and for topping up factory coated glass after a reasonable length of time The Treatment must always be used on existing shower installations to prepare for the Protector The Treatment is a cleaning material that is applied to the glass to ensure it is in the cleanest condition possible prior to application of the Protector If this pr
9. in on glass and metal sections for long periods do not allow the build up of lime scale and do not use caustic cleaners or abrasives Daryl showers trays If you have a Daryl shower tray scuffs and marks on acrylic trays can often be removed by the light use of a mildly abrasive cleaner applied with a damp cloth and polished off Other cleaning materials Ensure that if you use a non Daryl cleaning product it has a pH level between 4 amp 8 and is non abrasive Prolonged use of cleaners with a pH level outside the specified range can cause damage to metal sections and possibly affect the safe operation of your Daryl Shower All cleaning material including Daryl s must be wiped down after application Do not use spray and leave cleaning products on the metal surface as these may cause damage to your door or enclosure USER INSTRUCTIONS Warm Up Function Optional 1 2 3 4 Hint these User Instruction pages can be separated from the Fitting Instruction pages if desired Low Medium or High Flow Button Buttons glow BLUE when pressed Temperature Control Knob Warm Up Stop Button glows BLUE when powered Press the Warm Up push button The unit delays turning on to allow you to get out of the shower The Warm Up push button flashes for a number of seconds until water comes out of the handset at the desired temperature When the water is at the desired temperature the unit turns off waiting fo
10. ing the weight of the door slide the glass with a 3mm allen key the bottom roller into the bottom track 99 CFI230J Caution Locate other side of glass door panel between the roller and plastic glass guide Caution Lift the glass door up and slide the rollers onto the lintel Check the wall channel is vertical and mark through the 3 holes A Drill 3 x 6mm holes Seal behind channel and tighten screws Slide glass panel into slot in tray A and fit jamb onto wall channel B Fit the splash guard to the bottom of the panel Note lip faces to the outside of Enclosure and cutout is towards the wall end of the glass On the inside of the enclosure pull the rubber strip away from the wall jamb CFI230J 7 Ensure glass panel is vertical Drill 4 x 3mm holes Check glass is vertical If not through jamb into wall remove screws re drill and channel Fit the fixed roller to the tray on the same side as re fit as required lintel wall fixing applying sealant on the edges of the tray Note The seal A on the glass panel will need Note The seal A on the glass panel will need Re fit rubber strip over to be pulled away to allow the roller to be fitted to be pulled away to allow the cover to be fitted and re fitted afterwards and re fitted afterwards Fit t
11. ive packaging along the glass edges is kept in place for as long as possible to prevent damage before installation Wear protective footwear when lifting panels People not familiar with the fitting of Daryl Products may require the assistance from another person at certain stages of the procedure We have indicated these points in the process with the Caution Symbol N Wear Safety A glasses when drilling Caution Care amp Maintenance The unit should be cleaned regularly Use a non abrasive cleaner ideally with a pH i NON value of 4 to 8 applied with a soft cloth ABRASIVE Under no circumstances should scourers or CLEANER powerful detegents be used as these can damage oH VALUE the metallic surface of the frame and also tarnish 1t03 X the glass coating 4to8 If fitted correctly the unit should not require any sha maintenance other than cleaning If problems do occur contact the Daryl Technical Helpline Tel 0151 606 5000 CFI230 3 COMPONENTS Splashguard 4 CFI230 Standard Top Caps Lintel Seal Parking Block Side Panel Nylon Grub Screw x2 Blanking Cap Fixed Roller Fixed Head Water Delivery Only Carefully lift the Water Z Delivery System column and place the bottom into the wall jamb Be very careful not to scratch or damage the tray Support the weight of th
12. ll hold the handset in No flow or low flow rate Spray plate assembly Refer to Cleaning from the Shower Fittings blocked place Hose blocked or twisted Clear blockage or release twist in hose Digital Mixer Valve malfunction Contact Customer Services Drip from spray plate A small amount of water This is quite normal assembly on handset may be retained in the Changing the angle of shower fitting after the the shower fitting may shower control has been vary the draining time turned off This may drain over a few minutes Fixed Head Adjustment Move the spray head to the required Digital Mixer Valve Solenoid fault May position The spray head is adjustable in malfunction require cleaning or replacement Contact directions Customer Services both the horizontal and vertical Incorrect shower Maximum temperature Refer to Commissioning temperature incorrectly set Maximum temperature setting Digital Mixer Valve incorrectly Make sure that the hot fitted and cold water supplies are connected correctly 16 CFi230 CFI230 13 Setting Option 1 Operate the shower and set the desired flow and temperature then press and momentarily hold the Warm Up Stop and Medium push buttons at the same time The Medium push button will flash and COMMISSIONING SETTING 1 General beep three times to confirm the selection is successful 1 1 Turn on the water supply to the Digital Mixer The mixer is locked to your selected temperature and flo
13. ocess is not undertaken there is the likelihood of locking in dust dirt and stains under the Protector Daryl Protector acts as an invisible barrier on the glass to prevent the build up of lime scale soap scum stains and dirt Applied like a polish one application will last from months to years depending on use and the hardness of water in your area It will never crack peel discolour or build up Coated surfaces are kept clean simply by rinsing or wiping with a damp cloth and regular use of Daryl Glass Cleaner 18 CFi230J Regular cleaning e Mildew thrives in damp unventilated areas It is therefore important to always wipe down with a soft cloth or towel the glass and metal sections inside the shower every time it is used e Do not allow water to remain on glass and metal sections for long periods of time e Every week or two use Daryl Glass Cleaner to polish the enclosure including metal sections ensuring all surfaces are wiped down e In hard water areas do not allow lime scale to build up Stubborn deposits of lime scale can usually be removed by using a 50 50 solution of vinegar and water which should be rinsed off thoroughly and dried after use e Regular cleaning is required to remove the small amounts of residue that are not repelled by the Protector Everyday Care Wipe down the glass and metal sections with a soft cloth or towel and warm water after each time the shower is used Do not allow water to rema
14. ount parking block by on to the parking block tightening allen screw A PO os Take care not to damage pipe and cable protruding yg from wall Check the lintel is level Spot drill through 4 fixing holes in the If adjustment is required turn screw A wall jamb and mark the wall Only 4 of the on the panel clamps to lift or lower the rail 8 holes are using alternate sides A Note If the lintel cannot be made level by Carefully remove the panel from the tray adjusting the clamps remove the grub screws and fit the longer ones supplied in the parts pack Drill 4 x 8mm holes Fit plugs When the lintel is level tighten screw B on each panel clamp until it grips the glass u F Carefully lift the panel IMPORTANT DO NOT OVER TIGHTEN back into postion Fit caps to lintel C Loosely fit 4x QO screws Seal behind the wall channel and tighten 20 CFI230J CFI230J Q Check the wall channel and jamb is vertical The edge of the glass should fit against the end Loosely fit the parking block into the wall mount A Lift the lintel onto the glass The panel clamps Loosen screws A to adjust from side to side of the slot in the tray B To adjust the glass fit over the top edge of the glass and s
15. ps RH Fixed Head Slide Rail Water Delivery Water Delivery Water Delivery Wall Jamb Wall Channel amp Glass Clamp Stop Vinyl except 800 5mm NOTE The Water Delivery System is supplied attached to the Wall Jamb Splashguard 2m Pipe and Connector Electrical Cable CFI230J 5 ENCLOSURE INSTALLATION Fit roller securing caps to both top roller brackets Lift bottom roller up and tighten the fixing Caps will click and lock in place screw with a 3mm allen key Non Water Delivery Side only Carefully lift the assembly onto the tray The end Loosely fit wall channel into glass panel jamb of the glass panel fits into slot A on the tray The wall channel end sits on the flat section of the tray B Fit the cap to cover the screw Adjust wall jamb until glass is parallel to the Remove wall channel from jamb and place Cut the 2 metre pipe Connect pipework edge of the tray A When jamb is vertical mark against mark on wall to size Measure from edge of wall channel on the wall B the centre line of the Bottom Entry Top Entry connector i Bottom Entry A 1750mm Top Entry A 320mm 6 CFI230J CFI230 23 Loosen the screw fixing the bottom roller to Whilst support
16. r you to shower To Operate the Shower 1 2 3 4 Press the Low Medium or High flow push button Water will come out of the handset at the desired temperature To alter the showering temperature turn the temperature control knob Whilst the showering temperature stabilises the selected flow push button will flash Press the Stop push button at the end of your shower Caution Anyone who may have difficulty understanding or operating the controls of any shower should be attended whilst showering Particular consideration should be given to e the young e the elderly e the infirm e the disabled anyone who suffers from a medical condition that can result in temporary incapacity e g epilepsy or blackouts e anyone inexperienced in the correct operation of the controls CFI230J 11 Spray Settings The handset has three different spray actions Start Soothe and Massage and an Eco setting To adjust the spray setting turn the spray plate as follows 1 Start Water flows from the outer set of holes To select the Start setting turn the spray plate anticlockwise from the full clockwise position until it clicks once Spray Plate 2 Soothe Water flows from the middle set of holes To select the Soothe setting turn the spray plate anticlockwise from the full clockwise position until it clicks twice 3 Massage Water flows from the inner set of holes To select the Massage setting turn the spray
17. ul The Knob Position interfaces are locked F Note Selecting the Warm Up Stop and Medium push buttons at the same time again cancels the a a Factory Set 45 C lock mode option set The Medium push button will flash and beep three times ooo ee e Note Timeout allows you to run the shower for a set period of time before it automatically shuts off This can supply OFF and ON Oooo ee ee O 41 Trt Siac Sarai a ee ealle bse e O rr a ee a ee ee 2 2 Enabling Press and momentarily hold the Warm Up Stop and High push buttons at the same time Release the push buttons and press them again within 2 seconds The High push button will flash and beep only be set when the unit has not been used for a period of 30 minutes or after switching the unit s electrical Temperature Control Timeout Minutes Knob Position three times to confirm the selection is successful 3 Lock Mode Note Allows you to lock the unit during operation 3 1 There are two Safety Lock Modes Option 1 Locks the mixer to your flow and temperature settings Option 2 Locks the interface so no push buttons can be used Note The Warm Up Stop push button will be illuminated on the interface used to set the lock mode no other interface will be illuminated 4 2 Enabling Press and momentarily hold the Warm Up Stop and Low push buttons at the same time The Low push button will flash and beep three times to confirm the selection is successful 1 4 CFi230 C
18. w Pressing any flow push button turns the 1 2 Check for leaks over the complete system mixer ON Pressing the Warm Up Stop push button turns the mixer OFF 7 3 Turn on the electrical supply to the Digital Mixer Caution If the temperature control knob is altered while the mixer is in standby mode or while For the Pumped Version with the Slide Rail System pump priming can be helped by removing the handset the shower is in operation the water temperature settings will be changed to the new setting next time and lowering the end of the hose into the shower tray the shower Is used Note Selecting the Warm Up Stop and Medium push buttons at the same time again cancels the 2 Set the Maximum Temperature lock mode option set The Medium push button will flash and beep three times Note The maximum temperature of the unit can only be set when the unit has not been used for a period of 10 minutes or after switching the unit s electrical supply OFF and ON Setting Otion 2 2 1 Temperature Selection Set the temperature control knob to the desired position as per the table Note This can only be set when the mixer has not been used for a period of 10 minutes Switching the below unit s electrical supply OFF and ON cancels the lock mode Press and momentarily hold the Warm Up Stop and Medium push buttons at the same time The Temperature Control Temperature Selection C Medium push button will flash and beep three times to confirm the selection is successf
Download Pdf Manuals
Related Search