Kobe Range Hoods CX1836GS User's Manual
Contents
1. e Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filter What to Do In The Event Of a Range Grease Fire SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray and then turn off the burner KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES the flames do not go out immediately EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911 NEVER PICK UP A BURNING PAN You may get burned DO NOT USE WATER including wet dishcloths or towels a violent steam blast will result Use an extinguisher ONLY if a You have a Class A B C extinguisher and know how to operate it b The fire is small and contained in the area where it started c The fire department has been called d You can fight the fire with your back to an exit What to Do If You Smell Gas Extinguish any open flame Do not try to turn on lights or any type of appliance Open all doors and windows to disperse the gas If you still smell gas call the Gas Company and Fire Department right away CAUTION 1 For general ventilation use only Do not use to exhaust hazardous or explosive materials and vapors 2 To reduce the risk of fire use only metal ductwork 3 Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditionin2. CAUTION DRAIN OIL CONTAINER BEFORE OIL CAN OVERFLOW 1 The oil container attached underneath stainless steel filter can be removed by turning counter clockwise 2 To clean the stainless steel filter remove the screws leave in a safe place and slide 3 stainless steel filter out Both oil container and stainless steel filter should be washed with warm soapy water and dry completely before returning in place Both are top rack dishwasher safe To Replace Light Bulb CAUTION HALOGEN LIGHT UNIT MAY BE HOT WAIT UNTIL UNIT IS COOL 1 2 3 4 9 Make sure all control switches are off and range hood is unplugged Use a flat head screwdriver to pop out the protective covering as shown in Figure 13 Gently pull out the defective light bulb and discard Light bulbs should be 12V 20W maximum Refer to Figure 14 Push bulb securely into light socket Replace protective cover Plug in range hood Figure 13 Figure 14 10 SPECIFICATIONS MODEL SIZE COLOR VOLTAGE NUMBER OF MOTORS DESIGN FAN TYPE EXHAUST CONTROLS HALOGEN LIGHTS HOOD DIMENSION W x D x H DUCT COVER DIMENSION W xD x H OPTIONAL ACCESSORIES W x D x H WEIGHT lbs SPEED Air Capacity cfm oone CX1836GS 36 304 Commercial Stainless Steel 120V 60Hz 189W 1 18 Gauge Centrifugal Squirrel Cage 7 Round Electronic Touch Button 4 Buttons Power Control Speed Control Low amp High Speed Light Cont
3. SHARP EDGES PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING CLEANING OR SERVICING Preparations before Installation NOTE TO AVOID DAMAGE TO YOUR HOOD PREVENT DEBRIS FROM ENTERING THE VENT OPENING Decide the location of the venting pipe from the hood to the outside Refer to Figure 1 A straight short venting run will allow the hood to perform more efficiently ry to avoid as much transitions elbows and long run as possible This may reduce the performance of the hood Use duct tape to seal the joints between pipe sections If necessary prepare back wall frame with cross framing lumber for secure installation Using references on Table 1 and measurements on page 12 decide the level of the lumber Refer to Figure 2 Figure 1 1 Peel protective film off the duct cover and hood if any Place rubber seal on hood venting area as shown in Figure 3 Use eight 4x20 mm screws provided to attach plastic damper and rubber seal to hood venting area Refer to Figure 4 Figure 3 Figure 4 3 f necessary to remove the two rubber stands on the back of the hood unscrew and discard Hood Installation CAUTION If required to move the cooking range to install the hood turn OFF the power on an electric range at the main electrical box SHUT OFF THE GAS BEFORE MOVING A GAS RANGE 4 Using references on Table 1 and measurements on page 12 mark the leveling point for hood m
4. or removed b if notice of the defect has not been given within the period applicable C for failure of light bulbs d for physical damage e for surfaces damaged by use of improper chemical cleaning agents f if the appliance has been i subject to misuse abuse negligence accident incorrect installation or failure to follow the operating instructions ii connected to improper inadequate or faulty electricity service or exhaust ducts or flues or operated using incorrect or contaminated lubricants iii installed maintained or operated otherwise than in accordance with the instructions furnished by KOBE Range Hoods including the improper use of detergents bleaches or cleaners g for damage to range hood during transit delivery installation or removal h for damage by or resulting from attempted repairs conducted by anyone other than our Authorized Service Agent 17 3 The purchaser shall be responsible for any expenses involved in making range hood readily accessible for servicing and where the range hood is installed outside the main sales territory of the retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable for any traveling expenses and any costs of transporting the range hood or parts thereof to and from the dealer or Service Agent 4 The purchaser must produce proof of purchase together with this warranty certificate when making the claim 5 Damages caused during shipm
5. HE AREA HOUSING THE FAN WHILE THE FAN IS OPERATING For the optimal level of operation clean the range hood surface fan and oil container regularly To Clean Hood Surface CAUTION NEVER USE ABRASIVE CLEANERS PADS OR CLOTHS Regular care will help preserve its fine appearance 1 2 Use only mild soap or detergent solutions Dry surfaces using soft cloth If hood looks splotchy stainless steel hood use an orange base cleaner to clean the surface of the hood Avoid cleaner to get on the control switches Spread a light coating over the surface of the hood and leave on for a few minutes do not leave on too long or this may cause damage to hood finish Use soft towel to wipe off the cleaning solution gently rubs any stubborn spots Use a slightly damp towel to get rid of any cleaning solution Use dry soft towel to dry the hood 3 To bring the glow back into a stainless steel finish use a stainless steel cleaner 4 9 6 DO NOT allow deposits to remain for long periods of time DO NOT use ordinary steel wool or steel brushes Small bits of steel may adhere to the surface causing rust DO NOT allow salt solutions disinfectants bleaches or cleaning compounds to remain in contact with stainless steel for extended periods Many of these compounds contain chemicals which may be harmful Rinse with water after exposure and wipe dry with a clean cloth To Clean Oil Container Stainless Steel Filter and Hood Fan
6. ITCH POWER OFF AT SERVICE PANEL b Clean fan filter if any and grease laden surfaces frequently To reduce the risk of fire and properly disperse air make sure to vent air outside DO NOT vent exhaust air into wall spaces attics crawl spaces or garages NOTE This warranty is invalid without an authorized agent s receipt or if unit is damaged due to misuse poor installation improper use mistreatment negligence or any other circumstances beyond the control of KOBE RANGE HOODS authorized agents Any repair carried out without the supervision of KOBE RANGE HOODS authorized agents will automatically void the warranty KOBE RANGE HOODS will not be held responsible for any damages to personal property or real estate or any bodily injuries whether caused directly or indirectly by the range hood WARNING TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF TOP GREASE FIRE Keep fan filter if any and grease laden surfaces clean Always turn hood ON when cooking at high heat Use high settings on cooking range ONLY when necessary Heat the oil slowly on low to medium setting Do not leave cooking range unattended when cooking Always use cookware and utensils appropriate for the type and amount of food prepared Use this unit only in the manner intended by the manufacturer Before servicing switch power off at service panel and lock service panel if possible to prevent power from switching on accidentally
7. KORBE KOBE Brand Range Hood Model No CX1836GS CX 183 SERIES 4 HEIGHT INSTALLATION INSTRUCTIONS AND OPERATION MANUAL READ AND SAVE THESE INSTRUCTIONS CONTENTS Important Safety INSTUCIONS s oues soa repre este osi euo ners notio cid ias rotacion ius 1 Components of Salas stan AR 4 Operating IAS N s 8 MIS IRIS ISI IS 9 SPECIMEN a 11 Meastremelnts e 12 B ci EMT 13 Dada Muscat UU m TU 15 DI ONO ERE RC EE ELE EU IH T EP 16 Acci E O A A E 17 RERUM 19 READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY OBSERVE THE FOLLOWING 1 Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards including fire rated construction 2 When cutting or drilling into wall or ceiling be careful not to damage electrical wiring or other hidden utilities 3 Ducted hood must be vented to the outside a Before servicing or cleaning unit SW
8. RRANTY CERTIFICATE KOBE Range Hoods Inc warrants all products manufactured or supplied by it to be free from defects in workmanship and materials Its obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms and conditions stated below of any component part which its examination shall disclose to be so defective TWO YEAR WARRANTY SERVICE PERIOD Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase or original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until expiration of the original purchaser s warranty CONDITIONS The following conditions apply only in relation to the warranty expressly given in this certificate 1 This warranty applies only a within U S A and Canada b to range hoods used for PRIVATE SINGLE FAMILY USE if used for COMMERCIAL or MULTIPLE FAMILY USE or other purposes warranty is void 2 Repair of any fault to be provided under this warranty shall not be provided a if the identification number attached to the range hood has been altered rendered illegible
9. ces mark the leveling point for duct cover mounting bracket 14 Secure the duct cover mounting bracket to the wall with two screws not provided Refer to Figure 10 Make sure all screws are tightened 15 Hook the inner duct cover onto the duct cover mounting bracket and release the outer duct cover to fit onto the hood as shown on Figure 11 Figure 10 Figure 11 Final Assembly 16 Turn power ON in control panel Check all lights and blower operation 17 Make sure to leave this manual for the homeowner OPERATING INSTRUCTION This KOBE hood is equipped with a four button control panel with LED lights one powerful centrifugal squirrel cage with stainless steel filter two bright 12 volt 20 watt halogen lights and one oil container The four control buttons are Power Control On Off Speed Control Low amp High Speed and Light Control Refer to Figure 12 Figure 12 Light Control opeed Control Power Control High Speed Low Speed Turn On All buttons operate independently Press Power Control On Off to turn on to the prior selected speed or on off of halogen lights Select the desire speed from the Speed Control button Press Light Control button to turn halogen light on Turn Off Press Power Control On Off button to shut down all power immediately Press Light Control to turn halogen light off Press Speed Control to turn the speed off MAINTENANCE CAUTION NEVER PUT YOUR HAND INTO T
10. ent are not covered under our warranty CONSEQUENTIAL DAMAGE The warrantor is not responsible for any consequential damage SOME STATES DO NOT ALLOW THE EXCLUSION OF CONSEQUENTIAL DAMAGE SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU IMPLIED WARRANTIES STATE LAW Any implied warranties including the implied warranty of merchantability and fitness for purpose imposed on the sale by the laws of the state of sale are limited to two year from the date of original purchase Some states do not allow limitations on the duration of implied warranties This warranty gives you specific legal rights and may also have rights which vary from state to state SERVICE For service contact KOBE Range Hoods Inc 4934 Walnut Grove Avenue Suite 202 san Gabriel CA 91776 U S A Tel 626 309 1356 Fax 626 309 1366 Email customerservice koberangehoods com www KobeRangeHoods com 18 PRODUCT REGISTRATION Register Your Product Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until expiration of the original purchaser s warranty See warranty section
11. for complete warranty coverage information This appliance has been manufactured tested and inspected to the standards required by KOBE Range Hoods PLEASE MAIL IN YOUR WARRANTY REGISTRATION CARD AND PROOF OF PURCHASE TO KOBE Range Hoods Inc 4934 Walnut Grove Avenue Suite 202 oan Gabriel CA 91776 RECORD THE FOLLOWING INFORMATION FOR YOUR RECORD Model No Serial No Purchased Date Purchased From IMPORTANT PLEASE KEEP A COPY OF YOUR SALE RECEIPT OR INVOICE HANDY WHEN REQUESTING FOR SERVICE 19
12. g Engineers ASHRAE and code authorities 4 Activating any switch on may cause ignition or an explosion A WARNING ELECTRICAL SHOCK HAZARD Can result in serious injury or death Disconnect appliance from electric power before servicing If equipped the fluorescent light bulb contains small amounts of mercury which must be recycled or disposed of according to Local State and Federal Codes COMPONENTS OF PACKAGE Must keep all material for returns or refunds Range Hood Box A KOBE Range Hood with Two Piece Duct Cover B Warranty Registration Card C Instructions Manual D Duct Cover Mounting Bracket Hood Mounting Bracket F Plastic Damper G Screw Packages H Rubber Seal Inner Duct Cover Outer Glass Canopy Duct Cover C D E pa t F 4 x 20 mm 8 pcs d Safety Bracket 1 pc INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate the length of the installation please refer to Table 1 All calculation is measure in inches TABLE 1 A Height of Floor to Ceiling B Height of Floor to Counter Top Standard 36 C lt Preferred Height of Counter to Hood Bottom Recommended 27 to 30 D Height of Hood E Height of the Hood Installation B C F Height of Duct Cover E D A SAFETY WARNING HOOD MAY HAVE VERY
13. ght 12V 20W Max AENA O Bottom Casing AZAD 6 Control Box 1 FAZ J200 7 Hood Casing 1 FAZ A100 8 Hood MountingBracket razm02 Y 9 Plastic Damper Z J 1FACMOM 10 Transformer ANION 11 Electrical Wire Box 14 FAV G001 12 Processor Board 1FAXG10 Capacitor THAMG000 O 14 AlrChamber AIO 156 Motor ANOS 16 Blower AIO 17 Loknt o 1TFAMF200 18 BlowrCovr J 1FAVF1200 19 Duct Cover Mounting Bracket 1 FAV M20 20 InnerDuctCover 1 1 001 21 Air Chamber Cover 1 FAVA6 22 Outer Duct Cover AK AION 23 GlassCanopy AZ AON 24 LED Lights ee o AF 25 Control Panel YI FAZ 26 _ Rubber Seal AMOS 13 MODEL NO CX1836GS 14 CIRCUIT DIAGRAM MODEL NO CX1836GS tri Red 6 Brown M Cx emt H j 4 Brown 7 7 pe v m Blue i oes Brown Yellow and green NU 120V 60Hz DISCLAIMER 1 CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT REQUEST NAME AND SIGNATURE OF THE CARRIER S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM Upon acceptance of items owner assumes res
14. ounting bracket 5 Secure hood mounting bracket with screws not provided Refer to Figure 5 Figure 5 6 Align hood to hood mounting bracket on wall and hook hood into place as shown on Figure 6 amp 7 CAUTION MAKE SURE THE HOOD IS SECURE BEFORE RELEASING Figure 6 Figure 7 7 For safety purposes install the safety bracket with one screws not provided to the wall as shown on Figure 8 Ductwork Installation 8 Use 7 round aluminum or steel pipe to connect the plastic damper on the hood to the ductwork above 9 Use duct tape to make all joints secure and air tight Make sure pipe is connected between the gaps of the plastic damper Refer to Figure 9 Figure 8 Figure 9 Wiring to Power Supply ASAFETY WARNING RISK OF ELECTRICAL SHOCK THIS RANGE HOOD MUST BE PROPERLY GROUNDED MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES BEFORE CONNECTING WIRES SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY 10 Connect three wires black white and green to house wires and cap with wire connectors 11 Connect according to color black to black white to white and green to green 6 12 the operation of the hood before moving on to next step Make sure power is supplied to the hood Duct Cover Installation 13 Using Table 1 and measurements on page 12 for referen
15. ponsibility for its safe arrival Damages should be reported to carrier and a claim filed Failure to do this could result in the carrier refusing to honor your claim The carrier will furnish you with necessary forms for filing a claim DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY PLEASE INSPECT CONTENTS OF PACKAGE S CAREFULLY UPON RECEIVING We must be notified in writing of any damages and or missing parts within the allocated days upon receipt of package s Contact your local KOBE dealer or distributor or call KOBE for the time limit CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS NOTE ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR FACTORY Products must be returned in good working condition with ALL original parts and documentation packed in ALL original cartons fillers and shipping cartons A restocking fee of 25 will be charged for all approved return s EXCHANGES OR RETURNS MAY NOT BE ACCEPTED IF ANY PACKAGING IS MISSING MAKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE INSTALLATION Appearance flaws of the hood found after installation and not affecting hood performance is not covered under our warranty for returns or exchanges Service visits not covered under warranty will carry a service charge A Before Installation Return for exchange or refund please see above for acceptable returns B After Installation NO exchange or refund 16 WA
16. rol 12V 20W x2 CX1836GS 35 3 8 x 19 3 4 x 4 3 8 CX183DC 14 1 8 x 13 x 15 3 4 30 3 4 1 21 Inner Duct Cover Extension CX183 21DC 14 1 8 X 13 X 15 3 4 37 2 36 Stainless Steel Back Panel SSP36 36 x 1 10 x 32 Net Gross CX1836GS 48 5 53 Low High 400 600 1 3 2 8 In House Test Static Pressure 0 Specifications information is subject to change without notice 11 MEASUREMENT amp DIAGRAM All inch measurements are converted from millimeters Inch measurements are estimated All measurements in are millimeters VIEWING DOWN FROM THE TOP 35 7 8 910 1 2 3 16 6 55 455 17 15 16 1 400 15 3 4 i rK Dig _ PLASTIC gx sh d lt Tl AN Al SIL XI S WALL VIEWING FROM THE SIDE 7 ROUND PIPE 4 3 4 120 WALL e DUCT COVER MOUNTING BRACKET lt PLASTIC PLASTIC DAMPER rez DAMPER E 3 16 224 gt HOOD MOUNTING a hs 13 330 BRACKET 15 16 1 15 16 ERE 50 50 20 1 4 515 14 3 16 360 18 7 8 480 35 3 8 900 12 PARTS LIST MODEL NO CX1836GS MODEL SIZE Container Round THAMMOD Stainless Steel Filter 1 FAVA016 O Halogen Light Support FAB O Halogen Li
Download Pdf Manuals
Related Search