Knoll Systems Microphone IR100 User's Manual
Contents
1. be solid or stranded shielded or unshielded with a minimum of 28 gauge for runs under 200 22 gauge for runs under 500 and 20 gauge for runs up to 1000 Wires can be looped from IR100 to IR100 or home run Home runs normally offer more reliability and future flexibility 4 IR100s can be mixed and matched in larger systems with up to 10 infrared receivers such as the IR210 IR220 or IR250 5 To wire the system together connect the IR100 12V GND and SIG terminals to the corresponding IR54 or IR55 terminal Prepare the wire leads to and from the IR100 by stripping about of the insulation from each of the three leads Twist the strands tightly together so that they do not stick out of the connector and cause a short circuit Strictly observe polarity If you are connecting with the RJ45 connector you may need a RJ45 paralleling strip to parallel connect the wires from multiple IR receivers 6 Next plug the single or dual emitters into the IR54 or IR55 connection block IR100 system typical layout PS1202 12 V DC Power Supply Connection Block Note IR100 s are wired in parallel 7 IF using the RJ45 cat5 connection only you can connect the positive of a second 5 20 VDC power supply to the pin 5 labeled STAT Connect that power supply ground to pin 3 GROUND and plug the power supply into the switched outlet of the stereo receiver This allows the IR100 Systems power LED to turn on and off when the stereo receiv2. 40 Horseshoe Way Richmond BC V7A 4V4 Telephone 604 272 4555 Fax 604 272 5595 Made in Canada Knoll Systems All Rights Reserved IR100 Tabletop Infrared Receiver lt knoll Installation Instructions v1 3 Warning To be installed and or used in accordance with appropriate electrical codes and regulations Introduction Thank you for your purchase of a Knoll IR100 infrared receiver This receiver features the ability to pick up a remote control infrared signal and relay it on wires to another location up to 1000 or more Features e Tabletop box design available in black and light grey colors e Will relay almost all remote control types except some B amp O models e Can be connected with almost any three conductor wire including cat 5 e Requires very little power Suggest using PS1205 12 VDC 500 mA for up to 10 IR100 receivers e Upto 10 or IR100 IR210 IR220 IR230 and or IR250 can be connected in a single system e Connects with a three wire connector or RJ45 via cat 5 wire Installation Tips 1 Follow all local electrical amp building code requirements 2 The IR100 is usually mounted on a tabletop For easy installation and to ensure reliability it is suggested that a or PS1205 500 mA 12 VDC unregulated power supply IR31 single or IR34 dual emitters and one of the following IR54 decora inwall style 4 output or IR55 tabletop style 4 output connection block are used 3 Wires can
3. IR100 Infrared Receiver Specifications Specifications Infrared carrier frequency 30 60kHz Indoor reception range 20 25 feet 6 8 meters Nominal reception angle 50 degrees off axis Maximum wire length 1000 300m or even more with larger gauge wire 3 conductors minimum 24 gauge to 200 22 gauge up to 500 20 gauge to 1000 Unregulated 12VDC 40mA 2 65 x 2 9 x 1 1 67mm x 74mm x 28mm Wire requirements Power requirements Dimensions Requires 12VDC power supply emitter s and IR54 or IR55 connection block Warranty Knoll Systems warrants its products sold in the USA and Canada by authorized Knoll dealers to be free of defects in materials and workmanship This warranty extends for three full years from the date of purchase by the original consumer Any products returned to Knoll Systems and found to be defective by Knoll Systems within the warranty period will be repaired or replaced at Knoll Systems option at no charge Knoll Systems will not be responsible for the actual cost of installation or removal of the product nor for any incidental or consequential damages Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you This warranty gives you specific legal rights You may have additional legal rights that vary from state to state Knoll Systems www knollsystems com oll 145 Tyee Drive Point Roberts WA 98281 121
4. er is turned on and off 8 Now plug in the PS1205 for up to ten infrared receivers 9 The infrared system is usually left plugged in all the time to an unswitched outlet as it uses very little power 10 Test the infrared system to see if it is working properly Bright sunlight and passive infrared security systems can lower the distance that remote controls can work with an IR100 receiver If you have any questions or concerns please call and ask for infrared technical support at 1 800 566 5579 The help line is open from 7 30 a m to 5 00 p m Monday to Friday Pacific time RJ45 Wiring Diagram IR100 front and back RJ 4 5 System Talkback IR power LED Receiver on LED 0o0o0 0oo0o0o ZZ0 GH 222 4N 99 goxrege ce cE Ah D m m mir Wo ano
Download Pdf Manuals
Related Search