Home

Klipsch Speaker WA-2 User's Manual

1. enable recovery and recycling WIRELESS TRANSMITTER COMPLIANCE INFORMATION The term IC before the radio certification number only signifies that Industry Canada technical specifications were met This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator and your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Le terme IC avant le num ro de certification radio signifie seulement que les sp cifications techniques d Industrie Canada ont t respect es Cet appareil est conforme a FCC et IC l exposition aux rayonnements limites fix es pour un envi ronnement non contr l Cet appareil doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps Cet transmetteur ne doit pas tre co situ ou op rant en liaison avec toute autre antenne ou transmetteur This device has been designed to operate with the antennas listed below and having a maximum gain of x dB Antennas not included in this list or having a gain greater than x dB are strictly prohibited for use with this device The required antenna impedance is 50 ohms Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interf
2. Klipsch Owner s Manual IMPORTANT SAFETY INSTRUCTIONS READ these instructions KEEP these instructions HEED all warnings FOLLOW all instructions DO NOT use this apparatus near water CLEAN ONLY with dry cloth DO NOT block any ventilation openings Install in accordance with the manufacturer s instructions DO NOT install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 DO NOT defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wider blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 PROTECT the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 ONLY USE attachments accessories specified by the manufacturer 12 USE only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 UNPLUG this apparatus during lightning storms or when unused for long periods of time 14 REFER all servicing to qualified service personnel Servicing is requ
3. articular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Approved under the verification provision of FCC Part 15 as a Class B Digital Device Caution Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate this device This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada EU COMPLIANCE INFORMATION Eligible to bear the CE mark Conforms to European Union Low Voltage Directive 2006 95 EC Conforms to European Union EMC Directive 2004 108 EC WEEE NOTICE Note This mark applies only to countries within the European Union EU and Norway Bemmel ance is labeled in accordance with European Directive 2002 96 EC concerning waste electrical and electronic equipment WEEE This label indicates that this product should not be disposed of with household waste It should be deposited at an appropriate facility to
4. erence that may cause undesired operation of the device To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that permitted for successful communication Thank you for your purchase of the Klipsch WA 2 Wireless Subwoofer Kit The WA 2 will only operate with select Klipsch Energy Mirage and Jamo brand subwoofers that have a WA Port input The WA 2 is a 2 4 GHz product designed to wirelessly transmit a signal up to a 50 foot radius Packing List 1 Transmitter 2 Receiver 3 Power supply 4 Audio cable 5 Velcro strips 6 This Owner s Manual Setup 1 Decide where the subwoofer will go refer to your subwoofer owner s manual 2 Most receivers and pre amplifiers have a line level subwoofer output labeled Subwoofer Pre Out Sub Out SW Out etc If you have this connect one end of the supplied audio cable to it and connect the other end of the cable into WA 2 transmitter input C In absence of a subwoofer output connect Left and Right channel Pre Amp outputs from your receiver if provided to C and B inputs on the transmitter 3 Connect the cable from the WA 2 receiver to the WA Port on the back of the subwoofer Carefully match the 4 pins of the cable to the corresponding 4 holes on the WA Port and gently push in until connected Improper pin alignment can result in dama
5. ge to the connector 4 Plug supplied power supply cable into E on the WA 2 transmitter and plug other end into an AC wall outlet 5 Check to make sure Gain Switch A is in middle position OdB This position best matches the output voltage of most receivers and processors 6 Turn receiver pre amplifier on 7 Turn subwoofer to On or Auto On position 8 The WA 2 transmitter and receiver should be automatically paired with their red LED s D on solid and the subwoofer should now be operational 9 You can use the supplied Velcro strips to attach the WA 2 receiver to the back of the subwoofer Some subwoofers have two screws on back that the receiver attaches to TROUBLESHOOTING If the subwoofer does not operate and the red LED s D are flashing on the WA 2 transmitter and receiver a simple pairing is needed Push and hold in button F on the transmitter while pushing and holding button G on the receiver and keep pushed until both LED s stop flashing and glow solid approximately 5 seconds Since the WA 2 is a wireless device it may encounter RF interference from other wireless devices in the same area If there is difficulty pairing the transmitter and receiver or their signal connection fades you may need to move them closer together and or farther away from other wireless products Ifyou do not get a signal or get a low signal level from the subwo
6. ired when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with liquids such as vases are placed on the apparatus 16 To completely disconnect this apparatus from the AC Mains disconnect the power supply cord plug from the AC receptacle 7 The mains plug of the power supply cord shall remain readily operable CoN Sol A NS gt The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons The lightning flash with arrowhead symbol within an equilateral triangle is intended to WARNING To reduce the risk of fire or electrical shock do not expose this apparatus to rain or moisture WARNING No naked flame sources such as candles should be placed on the product CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING Do Not Open Risk of Electrical Shock Voltages in this equipment are hazardous t
7. o life No user serviceable parts inside Refer all servicing to qualified service personnel Place the equipment near a main power supply outlet and make sure that you can easily access the power breaker switch WARNING This product is intended to be operated ONLY from the AC Voltages listed on the back panel or included power supply of the product Operation from other voltages other than those indicated may cause irreversible damage to the product and void the products warranty The use of AC Plug Adapters is cautioned because it can allow the product to be plugged into voltages in which the product was not designed to operate If the product is equipped with a detachable power cord use only the type provided with your product or by your local distributor and or retailer If you are unsure of the correct Operational voltage please contact your local distributor and or retailer FCC AND CANADA EMC COMPLIANCE INFORMATION NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not in stalled and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a p
8. ofer make sure the subwoofer out level control on your surround receiver is set correctly usually at the halfway point sometimes labeled OdB If your subwoofer out level on your surround receiver is correct and you have adjusted the subwoofer volume level and the signal is still too low move the gain control A to the right 12dB to increase the signal to the subwoofer If the signal is too high move the gain control to the left 12dB to reduce signal strength

Klipsch Speaker WA-2 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents