KitchenAid KWC-200 User's Manual
Contents
1. KitchenAid DISPOSER INSTALLATION INSTRUCTIONS MODEL KWC 200 ELECTRICAL INSTALLATION INSTRUCTIONS 115 Volt 60 Hertz Follow your electrical code in all details In older houses with limited circuits or if it appears the circuit is heavily loaded run a line directly to the main fuse box l 2 Remove the electrical access cover on the bearing bracket assembly Install standard connector not furnished into threaded opening in bearing bracket assembly Install an operating control switch where it is easily accessible for the owner Recommended On Off switch suitable for operation of 1 2 H P motor Switch not furnished Run flexible conduit or equivalent from the control switch to the electrical power supply Insulate all connections Run flexible conduit or equivalent from the control switch to the disposer motor leads located in the bearing bracket assem bly Connect unit to ground See illustra tion Press wires into the electrical access com partment and replace cover NOTE Follow your local electrical code in all details In older houses with limited circuits or if it appears the circuit is heavily loaded run a line directly to the main fuse box GREEN LEAD TWIST SOLDER amp TO GROUND INSULATE BOTH CONNECTION CONNECTIONS PL 15194 MANUALLY OPERATED RESET BUTTON PUSH TO RESET IF MOTOR STOPS ON OVERLOAD OR JAM GENERAL INSTRUCTIONS 1 In old h2. e hook F onto support plate D then engage hc J onto support plate D Turn dispos to align with drain trap Snap lever I downward to lock 8 Connect the drain trap to the spout H If necessary pry lever I outward and turn disposer for better alignment 9 Check to assure that the grinding chamber is clean of any foreign objects and the flywheel is free to rotate Place the cover in position 10 Installation must be in accordance with local plumbing codes DISHWASHER CONNECTION Connecting the discharge of a dishwasher to a disposer will assure all waste particles discharged by the dishwasher are properly sized and flushed through to the main drain system A dishwasher drain inlet that will accept a 3 4 ILD hose is provided in the side the upper housing grinding chamber for nnection of the dishwasher discharge l Use a small cold chisel to cut out the back wall knockout of the dishwasher inlet boss of the disposer 2 Remove any pieces of the knockout and chips from the grinding chamber 3 Connect the dishwasher drain hose to the disposer inlet with a hose clamp TYPICAL INSTALLATIONS Height of drain should not exceed height of disposer dis charge opening KWC 200 63 8 8 1 4 14 3 16 Connection With Straight away Drain Spout WARNING This disposer must be properly grounded before operating by connecting the chassis ground ter
3. minal to a suitable ground com plying with the National Electric Code and or local electrical codes KitchenAid Division HOBART Pot Bee Troy Ohio 45374 Form 12664A 4 78 Printed in U S A
4. ouses it is generally good practice to clean out the existing drain line from sink to sewer before installing the DISPOSER 2 The disposer can be installed in steel monel stainless steel or cast iron sinks with a sink opening of 3 1 2 to 4 without sink alteration 3 Standard 1 1 2 O D or 2 O D drain pipe is satisfactory for drain lines Long horizontal drain lines should be elimi nated Drum traps and grease traps should not be used 4 Where possible the reversing toggle switch should be positioned where it is readily accessible PLUMBING INSTALLATION INSTRUCTIONS 1 Remove existing sink drain connections and clean drain opening 2 Remove disposer cover 3 Insert screwdriver under lever I and pry outward Disengage hooks J and F from support plate D 4 Disassemble items A B C and D of mounting assembly by prying snap ring E from groove in sink flange A 5 Apply a bead of permanent pliable sealing compound underneath sink flange A Insert the sink flange A into the drain opening NOTE THE SINK FLANGE MUST BE LEVEL BEFORE MOUNTING DISPOSER 6 Assemble paperboard flange seal B pres sure washer C and support plate D onto the sink flange and lock in place with snap ring E Tighten the three jack screws K EVENLY against pressure washer C to secure the mounting assem bly to the sink 7 Be sure the isolating splash guard G is in place Lift disposer and engag
Download Pdf Manuals
Related Search