KitchenAid KKFV01LP Series User's Manual
Contents
1. Aerator Assembly in the Faucet Care section 12 Reinstall the aerator into the faucet and tighten with a wrench Model KKFVO1LP _ Remove the threaded collar flat metal washer and flat rubber washer from faucet NOTE Do not remove the rubber O ring from the bottom of the faucet base A B C D C Flat metal washer D Threaded collar A Rubber O ring B Flat rubber washer 2 Feed tubing through the hole in the sink or counter top and then insert threaded shank into the hole Make sure the rubber O ring in the channel at the bottom of the faucet base is firmly in place 3 Working from under the sink or countertop reinstall the parts onto the threaded shank of the faucet in the following order flat rubber washer white triangular support flat metal washer and threaded collar A B C D A Flat rubber washer C Flat metal washer B White triangular support D Threaded collar 4 Align the faucet and firmly hand tighten the threaded collar to keep the faucet base from turning when moving the operating lever 5 Connect the red striped braided hose to the hot water supply valve Connect the blue striped braided hose to the cold water supply valve Hold the hoses in place when tightening the nut to keep the hoses from twisting 6 Move the faucet lever to the closed forward position and open supply valves Check connections for leaks 7 Remove the aerator from the faucet and2. A Rubber washer C Threaded collar B Aerator screen TROUBLESHOOTING Slow or no water flow Is the faucet lever in the ON position The lever control pattern is triangular with OFF toward the front of the faucet See Operating the Faucet Are the water supply valves fully open Turn the water valves ON Is the household main water supply turned OFF Check for water flow from a different faucet Are the braided faucet hoses twisted Untwist the hoses and check for kinks Is the aerator blocked Make sure the aerator is free of debris that could plug the holes See Cleaning Does the faucet lever move normally If the lever moves too freely or seems stuck the cartridge may need to be replaced Faucet leaks or drips at the spout It is normal for the faucet to drip up to 1 minute after turning off the water Is the faucet lever in the OFF position The lever control pattern is triangular with OFF toward the front of the faucet See Operating the Faucet Is the faucet lever in the OFF position but continues to leak from the spout The cartridge and the cartridge seals should be inspected for wear and replaced if necessary Faucet leaks around the lever Is the retaining nut that holds the cartridge in place loose Remove the faucet lever lever base assembly and cap to expose the cartridge retaining nut Tighten retaining nut Faucet lever is loose With the Allen wrench supplied tight
3. KitchenAid KITCHEN FAUCETS For questions about features operation performance parts accessories or service call 1 800 422 1230 or visit our website at www kitchenaid com Model Series KKFV0O1LP Model Series KKFV01SP Model Series KKFvoipP READ AND SAVE THESE INSTRUCTIONS FOR RESIDENTIAL USE ONLY IMPORTANT Installer Leave installation instructions with the homeowner Homeowner Keep installation instructions for future reference 8559765B TABLE ar CONTENTS INSTALLATION REQUIREMENTS nnannnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnne INSTALLATION INSTRUCTIONS nsanannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnne FAUCET USE ccsssssssssssssssseesusaesaesausaususesausaesaeesnusausousnusausausaesans 4 FAUCET CARE sccsscssssssssssssssusususaessessessessessousnesnesousnusaesausansans 4 INSTALLATION REQUIREMENTS Gather the required tools before starting installation Remove parts from carton Check that all parts are included Tools Needed m Adjustable wrench 2 Phillips screwdriver m Basin wrench optional m Slip joint pliers Parts Supplied All models m Faucet assembly m Mounting assembly Rubber O ring Flat rubber washer White triangular support Flat metal washer Threaded collar m a Allen wrench Model series KKFVO1SP and KKFV01PP m Weights 2 m Check valve assembly fiber seals 2 IMPORTANT m Observe all governing codes and ordinances m C
4. embly 8211411 11 Sprayer Stainless steel 8211402 12 O ring 11 Sprayer Chrome 8211416 This part is not serviceable 12 Aerator set 8211403 13 Screw 14 O ring 15 Base i 16 Fiber washer 8211404 17 Check valve assembly 8211410 18 Weight 8211407 19 Mounting assembly 8211411 20 Hose 8211405 This part is not serviceable Model KKFV01PP 4 3 2 aN m ao En 6 16 lra 19 18 ITEM DESCRIPTION PART NUMBER 1 Lever base assembly ij 2 Spring i 3 Lever Stainless steel W10198637 3 Lever Chrome W10198638 4 Setscrew i 5 Cap 6 Retaining nut j 7 Cartridge 8211401 8 Body i 9 O ring i 10 Base i 11 Teflon ring 7 12 Long plastic insert 8211418 13 Rubber washer W10186587 14 Sprayer Stainless steel 8211408 14 Sprayer Chrome 8211415 15 Aerator set 8211403 16 Check valve assembly 8211410 17 Fiber washer 8211404 18 Hose 8211405 19 Weight 8211407 20 Mounting assembly 8211411 21 Spray button spring W10200280 This part is not serviceable Teflon is a registered trademark of E l Dupont de Nemours and Company KITCHENAID FAUCETS WARRANTY ONE YEAR LIMITED WARRANTY For one year from the date of purchase when this faucet is installed operated and maintained according to instructions attached to or furnished with
5. en the setscrew in the lever Make sure the setscrew is flush with the lever so it does not stick out Pull out or down sprayer head does not pull out to a satisfactory distance or retract fully Models KKFV01PP and KKFV01SP only Are articles under the sink interfering with the hose Move the articles to provide clearance for the hose Are the weights positioned correctly on the spray hose The two weights should be spaced approximately 1 apart on the sprayer head side of the hose loop just above the bend See Install the Faucet Model KKFV01LP REPLACEMENT PARTS LISTS Model KKFV01SP V l 5 N 1 8 S 5 6 12 7 15 19 E 10 nE f 11 17 lt 16 18 H m 20 ITEM DESCRIPTION PART NUMBER ITEM DESCRIPTION PART NUMBER 1 Lever base assembly 7 1 Lever base assembly 2 Spring 2 Spring A 3 Lever Stainless Steel W10198637 3 Lever Stainless Steel W10198637 3 Lever Chrome W10198638 3 Lever Chrome W10198638 4 Setscrew 4 Setscrew 5 Cap 5 Cap 6 Retaining nut i 6 Retaining nut 7 Cartridge 8211409 7 Cartridge 8211401 8 Spout assembly 8 Spout assembly i 9 Aerator set 8211403 9 Short plastic insert 8211417 10 Base 10 Screen washer W10186588 11 Mounting ass
6. flush the hot and cold lines until water is clear NOTE The aerator is in the end of the faucet To remove and replace aerator see Aerator Assembly in the Faucet Care section 8 Reinstall the aerator into the faucet and tighten with a wrench FAUCET USE FAUCET CARE All Models Operate the faucet by moving the lever to the desired position f N x D C oe A Full hot C Full cold B Full on D Off Model KKFV01PP m The flow of water can be a stream or spray The default water setting is stream m The spray assembly can be drawn out of the faucet approximately 19 48 26 cm Water spray setting Push the diverter button on top of the spray assembly Water stream setting Turn off the faucet and then turn it back on The spray assembly automatically resets A Spray button B Spray assembly Model KKFV01SP m The flow of water can be a stream or spray The default water setting is stream m The spray assembly can be drawn out of the faucet spout approximately 12 30 48 cm Water spray setting Push the large diverter button on top of the spray assembly Water stream setting Push the small diverter button located below the larger button or turn off the faucet and then turn it back on A Spray button B Stream button Clean the faucet using a clean cloth and warm water or a very diluted solution of mild dish detergent in warm water Dry and polish the faucet with a soft clo
7. heck location where faucet will be installed Proper installation is your responsibility Make sure you have everything necessary for installation It is the responsibility of the installer to comply with installation specifications and with state and local plumbing codes m Keep faucet and water lines leading to faucet from freezing to avoid damage m The faucet requires a 1 3 5 cm diameter opening in sink or countertop If there is no hole for mounting it is recommended that you contact a qualified installer to drill the hole for your installation in a sink deck or countertop NOTE The thickness of the sink or countertop must not exceed 144 4 4 cm m Hot and cold water supply lines must be available If the water lines are not available it is recommended that you contact a qualified plumber to install the necessary piping m Faucet hoses are equipped with compression type seals and do not require sealing compound to keep from leaking m As with all metal objects follow proper handling techniques TROUBLESHOOTING ccccscsssssssssssessesseesseeseeseesosssessessesgssesen 5 REPLACEMENT PARTS LISTS csssssssssssssssssseeseeseessessessneessoees 6 WARRANTY cccessessesesssssesseeseesausauscecsecaesgesaesenusausousausaesausaecaneaesany 8 INSTALLATION INSTRUCTIONS IMPORTANT m Itis recommended that a qualified plumber installer install the faucet The faucet installation must comply with national and local
8. me phone number in your correspondence In the event of a warranty claim the owner will be required to provide proof of purchase model and serial number finish a copy of the original invoice showing the seller and date the product was purchsed and a complete description of the problem KitchenAid reserves the right to inspect any faucet reported to be defective prior to replacement of the faucet All decisions are final Keep this book and your sales slip together for future reference You must provide proof of purchase or installation date for in warranty service Address _ Write down the following information about your faucet to better help you obtain assistance if you ever need it You will need to know your complete model number and serial number Model number Dealer name Phone number Serial number Purchase date 8559765B 9 08 2008 All rights reserved Registered Trademark TM Trademark of KitchenAid U S A Printed in U S A
9. ough tenth year from the date of purchase when this faucet is installed operated and maintained according to instructions attached to or furnished with the product KitchenAid will replace the faucet cartridge with a faucet cartridge supplied by KitchenAid if the faucet cartridge is found to be defective in materials or workmanship under conditions of normal household use This warranty extends to the original purchaser only ITEMS EXCLUDED FROM WARRANTY Kirehenaid WILL NOT Pay for Service calls to correct the installation of your faucet to instruct you on how to use your faucet or to repair or replace household plumbing Limited warranty repairs after the first year when your faucet is used in other than normal single family household use Damage resulting from accident alteration unauthorized modification misuse abuse such as heavy impact fire floods acts of God improper installation or installation not in accordance with local plumbing codes or use of products not approved by KitchenAid Damages resulting from improper care or maintenance Damages resulting from improper applications such as exposure to corrosive chemicals photographic solutions etc Any unauthorized modifications made to the product after it leaves KitchenAid or its suppliers premises whether performed by a contractor service company or you Any labor costs during the limited warranty periods Repair or replacement parts for units operated outside the United S
10. plumbing codes and ordinances m The faucet should be examined for damage prior to installation Do not install a damaged faucet Instead return the faucet to the dealer from whom you purchased it IMPORTANT Before installing the faucet flush water supply pipes thoroughly Shut off water supply valves m Follow the installation instructions specific to your faucet model Models KKFV01SP and KKFV01PP 1 Remove the threaded collar flat metal washer and flat rubber washer from faucet NOTE Do not remove the rubber O ring from the bottom of the faucet base QO US C Flat metal washer D Threaded collar A Rubber O ring B Flat rubber washer 2 Insert faucet into sink or countertop m Feed tubing through the hole in the sink or countertop m Insert threaded shank into the hole NOTE Make sure the rubber O ring in the channel at the bottom of the faucet base is firmly in place 3 Working from under the sink or countertop reinstall the parts onto the threaded shank of the faucet in the following order flat rubber washer white triangular support flat metal washer and threaded collar oUb D C Flat metal washer D Threaded collar A Flat rubber washer B White triangular support 4 Align the faucet and firmly hand tighten the threaded collar to keep the faucet base from turning when moving the control lever Make sure the control lever is pointed toward the right hand side of the sink 5 Connec
11. t the sprayer hose to the water supply hose using the check valve assembly and the fiber washers Make sure the check valve assembly is positioned so that the arrow is pointing down away from the faucet and toward the sprayer head 6 Place a fiber washer between the sprayer hose and the check valve assembly and fasten them together Then place a fiber washer between the check valve assembly and the supply hose and fasten them together as shown D Fiber washer B Fiber washer E Sprayer hose C Check valve assembly 7 Connect the red striped braided hose to the hot water supply valve Connect the blue striped braided hose to the cold water supply valve Hold the hoses in place when tightening the nut to keep the hoses from twisting 8 Make sure the sprayer hose is fully inserted into the faucet body 9 Working from under the sink use the screws provided to attach the weights onto the sprayer hose Attach the weights to the sprayer head side of the hose loop just above the bend in the hose as shown NOTE The weights are for counterbalance only not for automatic retraction A Weights C Water flow direction B Sprayer hose 10 Move the faucet lever to the closed forward position and open supply valves Check connections for leaks 11 Remove the aerator from the faucet and flush the hot and cold lines until water is clear NOTE The aerator is in the end of the faucet To remove and replace aerator see
12. tates Transportation and labor costs associated with removal or reinstallation of covered parts DISCLAIMER OF IMPLIED WARRANTIES IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW Some states and provinces do not allow limitations on the duration of implied warranties of merchantability or fitness so this limitation may not apply to you This warranty gives you specific legal rights and you also may have other rights that vary from state to state or province to province KITCHENAID SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages so this exclusion or limitation may not apply to you This warranty gives you specific legal rights and you also may have other rights which may vary from state to state SON PAR QN Outside the 50 United States this warranty does not apply Contact your authorized KitchenAid dealer to determine if another warranty applies 8 08 If you believe you have a warranty claim contact KitchenAid through your Dealer Plumbing Contractor Home Center or E tailer Or call our Customer eXperience Center at 1 800 422 1230 from anywhere in the U S A or write KitchenAid Brand Home Appliances Customer eXperience Center 553 Benson Road Benton Harbor MI 49022 2692 Please include a dayti
13. th NOTE Do not use abrasive sponges or anti lime or acidic cleansers such as scouring agents Periodically remove and clean the aerator under running water If the aerator is very dirty soak it in household vinegar overnight Remove and Replace the Aerator Model KKFV01PP 1 Turn off water supply to faucet 2 Remove the aerator assembly threaded collar screen and rubber washer The spray button spring will also come out with the aerator assembly 3 Clean or soak only the aerator screen 4 Replace the spray button spring Insert the small side into the spray head around the slotted screw 5 Replace the aerator assembly and fully tighten the threaded collar with a wrench C Aerator screen D Threaded collar A Spray button spring B Rubber washer Model KKFV01LP 1 Turn off water supply to faucet 2 Remove the aerator assembly threaded collar screen and rubber washer 3 Clean or soak only the aerator screen Replace the aerator assembly and fully tighten the threaded collar with a wrench A Rubber washer C Threaded collar B Aerator screen Model KKFV01SP 1 Turn off water supply to faucet 2 Remove the aerator assembly threaded collar screen and rubber washer 3 Clean or soak only the aerator screen Replace the aerator assembly and fully tighten the threaded collar with a wrench idl QOuxsb a an j D i i E l t z 1 i ry 1
14. the product KitchenAid will replace the faucet with an equivalent faucet supplied by KitchenAid if this faucet is found to be defective in materials or workmanship under conditions of normal use This warranty extends to the original purchaser only SECOND THROUGH THIRD YEAR LIMITED WARRANTY ON STAINLESS STEEL FINISH residential installations only In the second through third year from the date of purchase when this faucet is installed operated and maintained according to instructions attached to or furnished with the product KitchenAid will replace the faucet with an equivalent faucet supplied by KitchenAid if the stainless steel finish on this faucet is found to be defective in materials or workmanship under conditions of normal household use This warranty extends to the original purchaser only SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CHROME FINISH residential installations only In the second through fifth year from the date of purchase when this faucet is installed operated and maintained according to instructions attached to or furnished with the product KitchenAid will replace the faucet with an equivalent faucet supplied by KitchenAid if the chrome finish on this faucet is found to be defective in materials or workmanship under conditions of normal household use This warranty extends to the original purchaser only SECOND THROUGH TENTH YEAR LIMITED WARRANTY ON FAUCET CARTRIDGE residential installations only In the second thr
Download Pdf Manuals
Related Search