Home

KitchenAid KECD806R User's Manual

image

Contents

1. KitchenAid PRODUCT MODEL NUMBERS KECD806R KECD866R Electrical A four wire or three wire single phase 240 volt 60 Hz AC only electrical supply is required on a separate 30 ampere circuit fused on both sides of the line A time delay fuse or circuit breaker is recommended Connected directly to the fused disconnect or circuit breaker box through flexible armored or non metallic sheathed copper cable with ground wire Flexible armored cable should connect cooktop directly to the junction box A U L listed 1 2 12 7 mm conduit connector must be provided at the junction box The recommended minimum copper wire size is 10 gauge However wire sizes and connections must conform to the requirements of the National Electrical Code and all local codes and ordinances Venting system Use metal vent only Exception Under a concrete slab PVC may be used Rigid metal vent is recommended Do not use plastic or metal foil vent This downdraft cooktop is rated at 60 feet 18 3 m of straight vent or the equivalent If vent length is 10 feet 3 m or less 6 15 2 cm diameter round vent may be used If vent length is more than 10 feet 3 m use 6 15 2 cm diameter round or 3 1 4 x 10 8 3 x 25 4 cm rectangular vent Venting system must terminate to the outside Cooktop location should be away from strong draft areas such as windows doors and strong heating vents or fans All openings in the wall or floor where c
2. cm Ka 45 7 cm floor gt 11 27 9 cm 8 20 3 cm Install rear wall junction box in shaded area Darker area is preferred Because Whirlpool Corporation policy includes a continuous commitment to improve our products we reserve the right to change materials and specifications without notice Dimensions are for planning purposes only For complete details see Installation Instructions packed with product Specifications subject to change without notice Ref 8286553 08 11 05
3. m 30 76 2 cm model 35 1 2 90 2 cm 36 91 4 cm model cutout width 21 53 3 om cutout depth 2 5 1 cm minimum space to front edge of countertop Countertop must be supported within 3 7 6 cm of cutout Select required duct cutout see Page 4 for exhaust duct cutout location r housing depth 3 ft 91 4 cm long power supply cable factory installed Minimum base cabinet dimensions 30 76 2 cm base cabinet width 24 61 cm base cabinet depth 25 63 5 cm countertop depth Countertop opening dimensions that are shown must be used Given dimensions are minimum clearances and provide required 0 0 cm clearance New installations Follow minimum dimensions given Replacement installation Be sure that front edge of cooktop is at least 1 1 2 38 1 mm back from front edge of countertop If cabinet has drawers drawers will need to be removed and drawer fronts installed on front of cabinet Side clearance 6 15 2 cm minimum clearance between side of cooktop and side wall is recommended for maximum ventilation performance Rear clearance 3 4 19 1 mm clearance between rear edge of cooktop and rear wall is recommended Motor blower clearance 2 51 mm minimum clearance between motor and cabinet is required for proper cooling 6 15 2 cm clearance is recommended for servicing access countertop a 5 12 7
4. ooktop is to be installed must be sealed 9 3 4 24 8 cm hole in rear or side of cabinet 17 gt 43 2 cm Exhaust Duct Cutout Locations 9 5 8 24 4 cm 30 76 2 cm cooktop 13 5 16 33 8 cm 36 91 4 cm cooktop Electric Built in Ceramic Downdraft Cooktop OVERALL DIMENSIONS 21 5 16 yo fs 30 3 8 77 1 cm 30 76 2 cm models 36 3 8 92 3 cm 36 91 4 cm models 2 15 16 74 6 mm burner box depth 15 5 8 39 6 cm CABINET OPENING DIMENSIONS 30 76 2 cm min 30 76 2 cm model 36 91 4 cm min 36 91 4 cm model lt lt when higher than 18 45 7 cm gt F See Note for minimum clearances X 21 53 3 cm Ny Do Not seal iei opening depth gt cooktop to countertop Nw Minimum distance to nearest combustible vertical surface extending 18 45 7 cm 29 1 2 74 9 cm 30 76 2 cm model 35 1 2 90 2 cm 36 91 4 cm model cutout width above cooktop N 1 25 4 mm NS Note 24 61 cm minimum when bottom of wood or metal cabinet is protected by not less than 1 4 6 4 mm flame retardant millboard covered with not less than No 28 MSG sheet steel 0 015 0 4 mm stainless steel 0 024 0 6 mm aluminum or 0 020 0 5 mm copper 30 76 2 cm minimum clearance between the top of the cooking platform and bottom of unprotected wood or sheet metal 29 1 2 74 9 c

Download Pdf Manuals

image

Related Search

Related Contents

鹿児島親子つどいの広場 なかまっち  Samsung 242MP Vartotojo vadovas  Philips SWV2142W 6 ft Component video cable kit  InLine 43055C  Samsung Galaxy Tab 2 7.0 16GB Grey  Betriebsanleitung  Hanns.G HH191DP  Philips MCD120/93 User's Manual  Bedienungsanleitung Passion RIC Hörer-im    

Copyright © All rights reserved.
Failed to retrieve file