KitchenAid KCC-151 User's Manual
Contents
1. SAVE THESE INSTRUCTIONS FOR FUTURE USE INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY THEY WILL SIMPLIFY THE INSTALLATION 1 After removing the shipping carton be sure to remove all protective packaging materials such as tape and shipping pads Put extra key knob in a safe place Waxy residue from protective shipping material may be removed from compactor with a mild solution of liquid household cleaner and water 2 Your compactor is designed for recessed installation A six 6 inch clearance from the right edge of the drawer front is desirable for added convenience in bag removal Also allow twenty three 23 inches in front of the appliance for drawer removal See Figure 3 COMPACTOR WALL OR OTHER OBJECTS RON NE FIGURE 3 3 The compactor s overall dimensions are Height 34 1716 min Depth 24 Width 15 Select a cabinet opening to fit See Figure 4 34 1 16 A rg ld MIN FIGURE 4 4 Remove drawer as shown a Grip handle and raise front of drawer urt t clears stops See Figure 5 b Grasp side ridges of the drawer and lift drawer out See Figure 6 FIGURE 5 5 Remove any materials that are shipped in the drawer Some models have a literature storage compartment located inside the front panel See Figure 9 DO NOT REMOVE THE BAG FIGURE 6 6 Lay two carton corner posts or other protective material such as a throw2. rug on the floor then lay the unit on either of its sides on the corner posts The corner posts will protect the finish of the compactor and the floor See Figure 8 NOTE Do not truck or handle by console FIGURE 8 Remove the cardboard shipping pad located on the bottom See Figure 8 Stand compactor upright 7 A grounded receptacle should be located 18 min from the floor and tn the center of the opening See Figure 9 4 18 MIN FIGURE 9 8 Before moving the compactor into position measure the cabinet opening as shown in Figure 10 To determine if height adjustment is required see steps 9 and 10 below CARINE OPENING 4 FIGURE 10 9 The rear wheels of your compactor are preset for a minimum cabinet opening of 34 1 8 to 34 174 position A To adjust for higher openings tilt the compactor to one side and support with a corner post or a screwdriver handle CAUTION Use care so that the compactor does not drop on your hand 10 To adjust the height remove screw from position A in Figure 11 Move the rear wheel and screw to position B or C 34 1 4 to 34 172 use position B 34 1 2 to 34 3 4 use position C ow 00 FIGURE 11 Repeat for other rear wheel 11 Loosen the screws in the top retaining brackets Rotate the brackets from shipping position to the install position Retighten See Figure 12 SHIPPING INSTALL ia A POSITION dige RETA
3. the drawer Remove spacer and inside panel See Figure 16 Remove spacer and center panel if supplied Remove outside front panel DO NOT SCRATCH Select the color you wish to have showing and carefully push the panel in the drawer trim Replace the spacer then carefully replace the remaining panels and spacers on the inside Replace the handle with the screws removed in Step 2 above Replace the drawer KITCHENAID DIVISION CAUTION COMPACTOR TO AVOID INJURY FROM MOVING PARTS REPLACE HANDLE BEFORE OPERATING CUSTOM DECORATING In place of the panel pack you may use a 1 4 thick wood panel to match your cabinets or other suitable decorative material See Figure 18 To do so 1 NaN Follow Steps 1 through 6 under Changing Panel Color Also remove all cardboard Slide decorative panel between trim pieces Remount handle with the screws previously removed Slide the drawer into the unit Paint wallpaper fabric etc can be applied directly to one of the panels 22 15 16 __ _ gt 14 5 8 FIGURE 18 HOBART troy OHIO 45374 FORM 14736 12 83 Part No 780521
4. INING BRACKETS B N FIGURE 12 NOTE Position A Compactor frame will be flush with cabinets Remove cabinet mount screws from retaining brackets Save for use in step 13 Position B Midpoint between position A and C Position C Drawer front will be flush with cabinets 12 When moving or lifting the compactor use a glove to protect and cushion your hand To prevent damage to floor covering do not allow the rear frame of the compactor to touch the floor when lifting or rolling See Figure 13 LIFT HERE FIGURE 13 Align the rear of the compactor with the cabinet opening Plug the power cord into a properly grounded receptacle See Figures 1 2 and 9 Lift the front of the compactor and roll into the opening until the retaining brackets stop the unit 13 Fasten the retaining brackets to the underside of the counter top with the screws provided Use auxiliary clip for fastening to cabinet front when counter top mounting method is not permissible See Figure 14 RETAINER BRACKET RETAINER BRACKET SX ae aes A A MOUNTING CLIP A Al Ihe MOUNTING SCREW MOUNTING SCREW COUNTER TOP MOUNTING ALTERNATE CABINET FRONT MOUNTING FIGURE 14 Lift the front of the compactor until it is parallel with the cabinet front Place a screwdriver or other wedge under the front edge of the compactor 14 Loosen the screws to the front levelers do not remove screws Pivot the leve
5. Installation Instructions for your new undercounter KitchenAid KCC 151 COMPACTOR BEFORE YOU USE YOUR COMPACTOR Be sure your compactor s properly installed in an appropriate level area and a place Suitable for the size function and protection of the compactor ELECTRICAL REQUIREMENTS Observe Ali Governing Codes and Ordinances A 120 Volt 60 Hz AC only 15 Ampere fused electrical supply is required Time delay fuse or circuit breaker is recommended It is recommended that a separate circuit serving only this appliance be provided DO NOT use an extension cord RECOMMENDED GROUNDING METHOD DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE POWER SUPPLY CORD 3 PRONG GROUND PRONG WALL RECEPTACLE For your personal safety this appliance must be grounded This appliance ts equipped with a power supply cord having a 3 prong grounding plug To minimize possible shock hazard the cord must be plugged into a mating 3 prong grounding type wall receptacle grounded in 3 PRONG accordance with the National Electrical Code and local GROUNDING codes and ordinances If a mating wall receptacle is not available it is the personal responsibility and obligation of POWER SUPPLY the customer to have a properly grounded 3 prong wall cono receptacle installed by a qualified electrician See Figure 1 FIGURE 1 IMPORTANT DO NOT REMOVE THIS INSTRUCTION SHEET UNTIL READY FOR INSTALLATION AFTER COMPLETING THE INSTALLATION
6. lers to the floor and retighten screws See Figure 15 Dns TO FIGURE 15 15 Replace the drawer ADJUSTABLE TOE PLATE In some installations the toe plate may rub the floor covering If this occurs the toe plate clearance may be changed as follows 1 Determine the amount of interference of the toe plate with the floor covering 2 Remove the drawer from the unit Refer to Step 3 of the Installation Instructions 3 Lay drawer so the front panel faces upward Protect the floor 4 With a ruler and a pencil or chalk draw a line where the toe plate interferes with the floor covering 5 Use a pair of scissors and cut toe plate along this line See Figure 16 6 Replace drawer in unit FIGURE 16 CHANGING FRONT PANEL COLOR During installation or in the future you may wish to change the front panel color Your compactor has an extra panel which offers four color options See detail of assembly in Figure 17 y A 1 A 4 n 0 4 Narrin SS Y 2 TWO SIDED COLOR PANELS 2 SPACERS Te WRB DRAWER TRIM FIGURE 17 CAUTION The panels have cut metal edges Handie carefully to avoid cuts to hands and scratches on panels To change the front panel color 1 PN aw N Remove the drawer from the unit See Step 4 of the Installation Instructions Remove handle by removing the screws at the top inside of
Download Pdf Manuals
Related Search