Keurig K75 User Guide
Contents
1. Seated Properly Not Seated Properly ti amp NOT READY Press and release the Power Switch found directly behind the right side of the brewer Switch is spring loaded and will return to original position The LCD Control Center will illuminate and indicate NOT READY NOTE A K Cup pack should not be used for this sequence The brewer will automatically fill the internal tank with water and then the water will be heated This will take about 4 minutes During the heating period the LCD Control Center will indicate NOT READY fig 3 Do not lift the Handle during this heating period Once the water is heated READY TO BREW will be indicated and the BREW Button will be illuminated fig 4 NOTE You may see small amounts of water coming from the Vent and dripping into the Water Reservoir during this and subsequent heating this is normal 9 Lift and lower the Handle Press the flashing BREW Button to start a cleansing brew without a K Cup pack When the brew cycle is complete pour the hot water into the sink NOTE A K Cup pack should not be used for this sequence 10 The one time set up process is now complete and you are ready to brew NOTE The brewer may take 15 30 seconds between brews and then READY TO BREW will be indicated Ready to Brew Your First Cup 1 LCD Control Center will indicate READY TO BREW 2 Place a cup or m2. Water quality varies from place to place If you notice an undesirable taste in your cup of coffee tea or hot cocoa such as chlorine or other mineral tastes we recommend you consider using bottled water or water from a filtration system For best results carefully follow manufacturer s instructions when using any water filtration system 4 Customize the size flavor amp brew that s perfect for you With the choice of over 250 varieties of K Cup packs and 5 brew sizes Extra Small Cup 3 25 oz Small Cup 5 25 oz Small Mug 7 25 oz Large Mug 9 25 oz and Travel Mug 11 25 oz your Keurig brewer gives you endless options to customize the size flavor and brew that s perfect for you For a strong intense cup select an Extra Bold K Cup pack with up to 30 more ground coffee than regular varieties and brew the size that s right for you The smaller the brew size the more intense flavor in your cup The larger the brew size the less intense flavor in your cup 5 Remove K Cup pack after use Please see page 7 for brewing instructions 6 Brewing into a travel mug To brew into a travel mug simply remove the Drip Tray Assembly and place the travel mug on the Drip Tray Base 7 Descale brewer regularly Please see pages 14 and 15 for instructions Unpacking Instructions 1 Place brewer box ona large steady surface such as a table or countertop or on the floor Open the box 10 Remove e
3. Or if you prefer you can watch the videos on your computer at www keurig com customer service Keurig is committed to your satisfaction If you have questions just give us a call to have them answered quickly without leaving the comfort of your home 1 866 901 BREW 2739 P20 201309003 KER755_K70 75 pdf 4C CMYK ZB2319 2013 09 06 To learn more about Keurig visit www keurig com or call 1 866 901 BREW 2739 Keurig Incorporated C UL US 55 Walkers Brook Drive Reading MA 01867 2013 Keurig Incorporated For Household Use Only All rights reserved Keurig Incorporated is a wholly owned P N G0 202471 000 Rev C subsidiary of Green Mountain Coffee Roasters Inc Pat Brevets www GMCR com patents 09 13
4. no output dispensed followed by the sound of air blowing out If this occurs e Turn off and unplug the brewer e If there is Keurig Descaling Solution in the Water Reservoir discard the contents rinse the Water Reservoir thoroughly and refill with water e Plug the brewer back in power on and repeat the Step 3 Fresh Water Rinse cycle The brewer should begin to function normally as the solution is rinsed out and the scale is removed If problem persists allow brewer to sit unplugged for at least 30 minutes before continuing with the rinse Visit us online for more information at www keurig com descaling P16 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 SECTION 3 Cleaning amp Maintenance continued Service Beyond these recommended cleaning and maintenance procedures this brewer is not user serviceable For service please refer to the Warranty section of this guide Storage Empty the Water Reservoir before storing and take care to ensure that you store your brewer in a safe and frost free environment Please be sure to store your brewer in its upright position to avoid water leakage from the inner tank If you store the brewer in a cold environment you run the risk of water freezing inside the brewer and causing damage When you prepare to use it after storage we recommend rinsing the Water Reservoir with fresh water and running three cleansing brews without a K Cup pack If you plan to move your brew
5. overflow The Drip Tray and Drip Tray Plate should be periodically inspected and rinsed clean To remove the Drip Tray Assembly simply slide it toward you keeping it level at all times to avoid spilling The Drip Tray and Drip Tray Plate should not be placed in the dishwasher They should be cleaned with a damp soapy non abrasive cloth and rinsed thoroughly Cleaning the K Cup Pack Holder Assembly 1 Cleaning the Parts The K Cup Pack Holder tis Assembly can be placed onto the top shelf of a dishwasher NOTE Use low temperature cycles in the dishwasher To remove it from the brewer lift the Handle and grasp the top of the K Cup Pack Holder with one hand while pushing up on the bottom of the K Cup Pack Holder from underneath with the other untilit releases fig 18 After cleaning align the K Cup Pack Holder with the opening using the two front ribs as a guide and snap into place from the top P14 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 SECTION 3 Cleaning amp Maintenance continued tio OD 2 Cleaning the Funnel The Funnel can be removed from the K Cup Pack Holder by pulling on it until it pops off fig 19 The Funnel is dishwasher safe To replace it just snap it back onto the K Cup Pack Holder Assembly i 3 Cleaning the Exit Needle The Exit Needle is located on the inside bottom of the K Cup Pack Holder Assembly Should a clog arise due to coffee grinds it can be cleaned us
6. ANY OTHER EXPRESS WARRANTY WHETHER WRITTEN OR ORAL IN ADDITION KEURIG HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO YOUR K70 K75 PLATINUM BREWER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE Some states or provinces do not allow disclaimers of such implied warranties or limitations on how long an implied warranty lasts so the above limitation may not apply to you depending on the state or the province of purchase How do you obtain warranty service Keurig brewers are high quality appliances and with proper care are intended to provide years of satisfying performance However should the need arise for warranty servicing simply call Keurig Customer Service at our toll free phone number 1 866 901 BREW 2739 Please do not return your brewer for servicing without first speaking to Keurig Customer Service to obtain an Authorization to Return number ATR Keurig brewers returned without an ATR number will be returned to the sender without servicing Keurig Incorporated 55 Walkers Brook Drive Reading MA 01867 1 866 901 BREW 2739 P19 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 Scan Click Call Learn more and reach us quickly without leaving home Scan here for videos about caring for your brewer vo Have questions We re here to help Scan this QR code with your smartphone for step by step videos on cleaning descaling and more
7. HORT CORD INSTRUCTIONS A short power supply cord is provided to reduce the risk of becoming entangled in or tripping over a longer cord If an extension cord is used 1 the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance 2 the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally and 3 the extension cord must include a 3 prong grounding plug THIS PRODUCT IS FOR HOUSEHOLD USE ONLY WARN N G THIS PRODUCT CONTAINS CHEMICALS INCLUDING LEAD WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM WARNING WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT REMOVE THE RISK OF FIRE OR BOTTOM COVER NO USER SERVICEABLE ELECTRIC SHOCK PARTS ARE INSIDE REPAIR SHOULD BE DONE DO NOT OPEN BY AUTHORIZED SERVICE PERSONNEL ONLY TABLE OF CONTENTS KEURIG GOURMET SINGLE CUP HOME BREWING SYSTEM K70 K75 Platinum Brewer Using Your Brewer SET UP Helpful HINES esise hor cosas evvertcceesttceccdacaszacaseess teteeyeazea4puaitcsesies 4 WY AGK I Oe sess yavensievevenvvvenveseecececGacaveetavecuedscsceseclacdeuscyevercesiesaetaveneseceety 4 PG LMS Ass air ENEE ERTA 5 SECTION 1 SET UP amp FIRST BREW Set Yp amp First BOW 2 isstieccatestascessesseseaecettbsastatacassasestiieveennezentsape
8. P1 201309003 KER755_K70 75 pdf 4C CMYK ZB2319 2013 09 06 OWNER S MANUAL GE Single Cu KEU RIG IK R Brewing Sem P2 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 IMPORTANT SAFEGUARDS safe Operation amp Use c UL us When using electrical appliances basic safety precautions should be followed including the following Read all instructions before using Do not touch hot surfaces Use handles and knobs when available This appliance must be properly installed and located in accordance N wo with these instructions before it is used BF The use of accessory attachments not recommended by the appliance manufacturer may result in fire electrical shock or injury to persons Do not place on or near a hot gas or electric burner or in a heated oven Do not use outdoors To protect against fire electric shock o ve and injury do not immerse cords plugs or the appliance in water or any other liquid Do not overfill the Water Reservoir with water Use only water in this appliance Do not put any other liquids or foods in the Water Reservoir except as instructed in the Cleaning Instructions in this guide 10 Turn off and unplug the brewer before cleaning or maintenance Allow to cool before putting on or taking off parts and before cleaning the appliance co so 11 For best operation plug the appliance into its own electrical outlet on a dedicated circui
9. T AUTO OFF fig 11 P11 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 Press or hold the Left Button under the blinking H to advance 1 hour at a time up to 9 hours After setting the desired Auto Off time press the MENU Button five times to scroll through the remaining programming options and exit the programming mode AUTO OFF SET fig 12 will now be displayed to indicate that it has been set SETON TIME BREW TEMP BREW SIZE Press or hold the Right Button under the M to scroll through the minutes to your desired ON TIME minutes After setting the desired time press the MENU Button to save the ON TIME and move to the SET OFF TIME fig 14 Ifyou want to program an OFF TIME repeat the procedure above in steps b amp c to program your desired OFF TIME fig 14 To complete the process press the MENU Oo CG Oo d To cancel the Auto Off feature press the n MENU Button twice to reach the AUTO OFF Buitonthreemoretme s tosxitihe Set x2 Hours programming mode Press and release the Left Button under the blinking H to advance one hour at a time until OFF is indicated programming mode The LCD Control Center will now indicate the options you have set g The Auto On Time and Auto Off Time functions operate independently from one another To cancel either set function follow the steps above and u
10. Vent P Power Cord Q Power Switch not shown located rear right side of brewer R LCD Control Center S Left Button T Right Button U MENU Button V BREW Button SECTION 1 Set Up amp First Brew IMPORTANT You cannot use your Keurig brewer until it has been set up for its first use NOTE If brewer has been exposed to temperatures below freezing allow brewer at least two hours to reach room temperature before brewing A frozen or extremely cold brewer will not operate Setting Up Your Brewer fig D 1 Unwrap cord and plug the brewer into a grounded outlet Remove all pieces of packing tape and clear plastic sticker from LCD Control Center Place a large mug 10 oz minimum on the Drip Tray Plate Remove the Water Reservoir from brewer by first removing Lid from the Water Reservoir fig 1 then lifting the Water Reservoir straight up and toward front of brewer may be tight fig 2 A Rinse with fresh water FillWater Reservoir with bottled or filtered water so that the water level is to and not beyond the MAX FILL line 5 Place Water Reservoir base into the left side of the brewer and be sure the Water Reservoir Lock Tab engages with the brewer Replace Lid on Water Reservoir NOTE Please ensure the Water Reservoir is seated properly so that the back of the Water Reservoir is flush with the brewer fig 2B and C P6 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06
11. blue light in the Water Reservoir will no longer be illuminated NOTE You may get more coffee tea or hot cocoa in your cup during your next brew We recommend that you perform a cleansing brew after a terminated brew Then your NEXT brew will be the volume you have selected fi Adding Water The LCD Control Center will indicate ADD WATER when the level in the Water Reservoir is lowor if the Water Reservoir has been removed NOT READY ees fig 9 The blue light in the Water Reservoir will also blink when water needs to be added The brewer will not allow you to brew when ADD WATER is indicated fig 9 P9 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 The Water Reservoir can be filled in two ways 1 Open the Easy Fill Lid and pour water directly into the Water Reservoir while it is still attached to the brewer Fill with water to and not beyond the MAX FILL line Close the lid The entire Water Reservoir Lid may be removed completely if preferred 2 Remove the Water Reservoir from brewer by first removing Lid from the Water Reservoir then lifting the Water Reservoir straight up and toward front of brewer Fill with water to and not beyond the MAX FILL line Place the Water Reservoir back on the brewer and replace the Lid IMPORTANT Do not remove the Water Reservoir during the brewing process Brewing Iced Beverages Your iced tea and iced coffee taste best when fresh brewed hot over ice Try it by p
12. continued a 2 Extra Small Cup Bb 3 25 oz Large Mug Y 9 25 oz 7 Small Cup 5 25 oz ED Travel Mug 11 25 oz Small Mug 7 25 oz Enjoy your first cup Once the brew size is chosen press the BREW Button The BREW Button will stop flashing and the Left and Right Buttons will no longer be illuminated The LCD Control Center will indicate BREWING and the selected brew size icon will be lit fig 8 CAUTION There is extremely hot water in the K Cup Pack Holder during the brew process To avoid risk of injury do not lift the Handle or open the K Cup Pack Assembly Housing during the brew process There may be a short pause prior to beverage being dispensed The entire brew process lasts for approximately 1 minute and ends with a burst of air to remove all liquid from the K Cup pack Lift the Handle and dispose of the used K Cup pack CAUTION K Cup pack will be hot of Keurig Brewed gourmet coffee tea or hot cocoa 11 The LCD Control Center may indicate NOT READY as the brewer heats water for the next brew cycle READY TO BREW will be indicated after about 15 seconds Stopping the Brew Process If you need to stop the brewing after the process has started press and release the Power Switch to turn the brewer OFF The flow of coffee tea or hot cocoa will stop the heating element will shut off and the LCD Control Center and the
13. ed in the LCD Control Center NOTE If power is interrupted to the brewer by unplugging it or if power is lost follow the procedure above to reset the time as the clock will not be visible until the time is set Brew size and brew temperature settings are remembered and restored automatically All other settings will be restored automatically after clock is set Programming On Off Features The brewer provides three modes so that you can enjoy gourmet coffee tea or hot cocoa on your own schedule By programming your brewer to turn on each morning you will never have to wait for the brewer to warm up to brew a gourmet cup of coffee It will take the brewer approximately 4 minutes to warm up from room temperature 1 Leave it ON all the time The brewer can be left on all the time so that it is always ready to brewa fresh cup of gourmet coffee tea or hot cocoa To turn the brewer off at any time simply press and release the Power Switch NOTE Although the clock remains on if set you can not brewa cup of coffee tea or hot cocoa Press and release the Power Switch again to restore power to the brewer You will have to wait for the water to heat up before the brewer is ready to brew 2 Set the brewer to AUTO OFF following a specified period of time after the last brew a Press the MENU Button twice to program the Auto Off feature The LCD Control Center will display the programming options with a small arrow next to SE
14. edaase 6 SECTION 2 CONTROLS amp INDICATORS Setting the Cl CK essri ii ai 10 Programming On Off Features es 10 Programming Brew Temperature Hr Programming BOW SIZO seinri 13 SECTION 3 CLEANING amp MAINTENANCE CIEMNO sirra oen E EEE 13 Descaling 14 SOIE Ta EA AE E A 16 SECTION 4 TROUBLESHOOTING cece eee 17 SECTION 5 WARRANTY 0 0 cececccc ennen eres 18 Record your Brewer Serial Number here See Unpacking Instructions on page 4 for serial number location Removing the serial number label from the brewer will void warranty P4 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 Set Up Helpful Hints 1 Plug brewer into its own grounded outlet If the electric circuit is overloaded with other appliances your brewer may not function properly The brewer should be operated on its own circuit separate from other appliances N Keep your brewer turned ON To brew a fresh cup of coffee tea or hot cocoa anytime you want keep your brewer turned ON all the time However the brewer is fully programmable so you can set it to turn on and off automatically to match your schedule Or if you prefer set the brewer to automatically turn off after a period of time Follow the simple instructions on pages 10 13 to find the settings that are most convenient for you 3 For the best tasting gourmet coffee tea or hot cocoa Keurig recommends using bottled or filtered water
15. en fill the empty bottle with water and pour into the Water Reservoir Press he Power Switch to turn the brewer back on e Place a large mug on the Drip Tray Plate and run a cleansing brew using he largest brew size Do not use a K Cup pack Pour the contents of the mug into the sink STEP 2 SECOND DESCALING SOLUTION RINSE e Repeat the brew process without a K Cup pack until ADD WATER is indicated Let brewer stand for at least 30 minutes while still on e After 30 minutes discard any residual solution and rinse the Water Reservoir thoroughly STEP 3 FRESH WATER RINSE e Ensure the Water Reservoir is filled with fresh water to and not beyond the MAX FILL line e Place a large mug on the Drip Tray Plate and run a cleansing brew using the largest brew size Do not use a K Cup pack Pour the contents of the mug into the sink e Repeat brew process until you have completed at least 12 brews using the largest brew size You may need to refill the Water Reservoir at least one time during this process NOTE If DESCALE is still indicated after completing the procedure repeat the descaling procedure above NOTE The cleaning action of Keurig Descaling Solution may result in a foam dispensed from the brewer This is natural as the solution is reacting with the scale inside For a brewer that is heavily scaled the brewer may not fill properly after the descaler is added If this occurs you may see only a small or
16. er to a different location turn the brewer off unplug it and empty the Water Reservoir If your brewer has been in an environment below freezing please be sure to let it warm to room temperature for at least 2 hours before using Transport brewer in the upright position to ensure inner tank does not leak through vent P17 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 SECTION 4 Troubleshooting SITUATION SOLUTION SITUATION SOLUTION Brewer does not e Plug brewer into an independent outlet Brewing a The Exit Needle may be clogged refer to page 14 have power Check to be sure that it is plugged in securely partial cup Clean the K Cup Pack Holder Assembly if necessary Plug into a different outlet and rinse under faucet refer to page 13 e Reset your home s circuit breaker if necessary e The Water Reservoir may have been removed during e Make sure that the Power Switch has been turned brewing Replace the Water Reservoir and perform a on and the LCD Control Center is illuminated cleansing brew without a K Cup pack Descale the brewer refer to page 14 Brewer will e After placing the K Cup pack in the K Cup Pack e If you have repeated the descale procedure on your not brew Holder make sure the Handle is pushed down securely brewer two times and it is still only brewing and the LCD Control Center indicates READY TO ies Then press the Left Right or BREW Button e If the LCD Control Center indicate
17. iance is properly grounded 22 Do not use the appliance for other than its intended use SAVE THESE INSTRUCTIONS WARNING TO USERS AND PARENTS 1 DO NOT permit children to use brewer unless there is adult supervision Brewer dispenses very hot water 2 SPECIAL NOTICE FOR HOT COCOA USERS IMMEDIATELY AFTER USING A HOT COCOA K CUP PACK RUN a Hot Water Brew Cycle without a K Cup pack to avoid the possibility of clogging the exit needle DO NOT assume the next user will do this P3 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 CAUTION There are two sharp needles that puncture the K Cup pack one above the K Cup Pack Holder and the other in the bottom of the K Cup Pack Holder To avoid risk of injury do not put your fingers in the K Cup Pack Assembly Housing CAUTION There is extremely hot water in the K Cup Pack Holder during the brew process To avoid risk of injury do not lift the Handle or open the K Cup Pack Assembly Housing during the brewing process CAUTION Do not fill above MAX FILL line If you fill the Water Reservoir above this point you may occasionally get a larger brew than you selected for your first brew of the day If you prefer to have your reservoir filled to the top we recommend you use a large mug for your first brew of the day to avoid any risk of overflow CAUTION Please always keep the brewer in its upright position to avoid potential injury and or damage to your brewer S
18. ing a paper clip or similar tool Remove K Cup Pack Holder Assembly and detach Funnel Insert the paper clip fig 19 into the Exit Needle to loosen the clog and push it out The K Cup Pack Holder is dishwasher safe CAUTION There are sharp needles that puncture the K Cup pack above the K Cup Pack Holder and in the bottom of the K Cup Pack Holder To avoid risk of injury do not put your fingers in the K Cup Pack Assembly Housing Cleaning the Water Reservoir amp Water Reservoir Lid 1 Rinse the filter screen with the strong force of water from your faucet 2 If you have a sprayer aim the water spray at the filter screen 3 Fill the Water Reservoir with approximately two inches of clean water and agitate shake the Water Reservoir Empty the Water Reservoir then fill it with clean water and return it to the brewer If needed repeat above procedures CAUTION Please rinse the Water Reservoir thoroughly after cleaning This will ensure that no cleaners or cleaning solutions remain as they may contaminate the water supply in the brewer Descaling Your Brewer The Water Reservoir Lid and Water Reservoir should be periodically inspected and cleaned The Water Reservoir Lid or Water Reservoir should not be put into the dishwasher They should be cleaned with a damp soapy non abrasive cloth and rinsed thoroughly Do not dry the inside of the Water Reservoir with a cloth as lint may remain To clean the filter
19. lacing a tall cup filled with ice on the Drip Tray Plate the Drip Tray Assembly can be removed to accommodate taller cups choose your favorite K Cup pack select the brew size and press the BREW Button Also look for the Brew Over Ice icon on K Cup packs specially crafted to brew over ice IMPORTANT Do not brew into a cup made of glass Doing so may cause the glass to crack or break Brewing Hot Water Your brewer is able to produce hot water for making hot cocoa from a packet for use in cooking for making soups etc Simply follow the instructions on page 7 Ready To Brew Your First Cup without adding a K Cup pack NOTE After brewing a hot cocoa K Cup pack we recommend running a cleansing brew without a K Cup pack Purging the Brewer If your brewer has not been used for more than one week you should purge the water from the internal tank 1 If there is water in the Water Reservoir remove the Lid then lift the Water Reservoir straight up and away from brewer Discard water rinse and refill with water Place the Water Reservoir back on the brewer and replace the Lid If there is no water in the Water Reservoir simply refill 2 Be sure the brewer is turned on Lift and lower the Handle on the brewer without inserting a K Cup pack 3 The LCD Control Center will indicate READY TO BREW Brewa Travel Mug 11 25 oz serving of water do not use a K Cup pack 4 Repeat steps 2 and 3
20. nclosed literature Turn the box on its side with front of box face down Reach into the box and grasp the plastic bag that contains the brewer Carefully pull the plastic bag and packaging materials toward you and out of the box The brewer will still be encased in the polyfoam and be on its side Remove the top polyfoam packaging material Carefully lift brewer off of the bottom polyfoam and place it upright on a flat steady surface Lift plastic bag off of brewer Record the serial number for this brewer on page 3 of this guide The serial number can be found on the bottom of the brewer box or on the brewer behind the Drip Tray when removed Place the brewer upright on a flat steady surface Remove tape holding Water Reservoir in place We recommend you save all packing materials in case future shipping of the product is necessary WARNING Keep all plastic bags away from children P5 201309003 KER755_K70 75 pdf 1C kK Features K70 K75 Platinum Brewer K70 K75 Platinum Brewer ZB2319 2013 09 06 READY TO BREW eebBP MENU Controls and Indicators A Water Reservoir Lid B Easy Fill Lid C MAX FILL D Water Reservoir E Water Reservoir Lock Tab Slot F Handle G Funnel H K Cup Pack Holder G and H are the K Cup Pack Holder Assembly l Lid K Cup Pack Assembly Housing Housing Drip Tray Plate Drip Tray Drip Tray Base ZSrx 5 0
21. ou have reached your desired brew emperature press the MENU Button twice to exit the programming mode BREW TEMP SET will be indicated in the LCD Control Center if you have changed it from 192 P13 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 5 To change the brew temperature again repeat steps 1 through 3 to change the temperature up or down remembering that the temperature can only be between 187 and 192 NOTE At high altitudes over 5 000 feet if boiling occurs use the temperature adjustment to lower the temperature Programming Your Brew Size ti The brewer is preset with the Small Mug 7 25 oz as the default brew size The default brew size allows the user to avoid scrolling through brew sizes if a particular size is chosen most often To change the default brew size to your desired brew size Press the MENU Button six times Using Left and Right Buttons select your desired default brew size fig 17 press the MENU Button once to exit The LCD Control Center will indicate the brew size set Once the desired default brew size Is selected SECTION 3 Cleaning amp Maintenance Cleaning External Parts Regular cleaning of the brewer s external components is recommended 1 Never immerse the brewer in water or other liquids The Housing and other external components may be cleaned with a damp soapy non abrasive cloth 2 The Drip Tray can accumulate up to 12 oz of
22. rate independently from one another To cancel either function follow the steps above and use the H and M buttons to advance to 12 00 AM When you reach 12 00 AM the LCD Control Center will indicate OFF and the function will be disabled fig 15 NOTE The Auto Off timer and the On Off Time programming options operate independently but can also be programmed to work together For example you can set the On Time function to turn on at 7 00 AM and then set the Auto Off timer function to turn off the brewer two hours after the last brew P12 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 Programming Brew Temperature 187 192 F The brewer is preset to brew at a temperature of 192 You can adjust this temperature down by 5 degrees if you prefer a cooler cup of coffee tea or hot cocoa Simply follow the instructions below 1 Press the MENU Button five times to program fis he Brew Temperature feature 2 The LCD Control Center will now display the SPR programming options with a small arrow next BNS o SET BREW TEMP fig 16 Also the crock emperature 192 initial setting will be ee mrs displayed at the top of the LCD Control Center BREW SIZE o indicate the current temperature setting 3 A minus sign will appear over the Left Button and or a plus sign over the Right Button Use Q Q hese Buttons to raise or lower the temperature 4 4 one degree at a time z 4 Once y
23. s ADD WATE add water to the Water Reservoir Fill to and not beyond the MAX FILL line Make sure the Water Reservoir is seated properly in its base e If the LCD Control Center indicates ADD WATER even after refilling contact Customer Service a 866 901 BREW 2739 The Exit Needle may be clogged refer to page 14 f the LCD Control Center indicates PRIME and the blue ligh A REW with the Left Right and BREW Buttons flashing in the Water Reservoir is flashing see below LCD Control Center Completely remove the Water Reservoir and indicates PRIME thoroughly clean refer to page 14 Ensure the and the blue lightin Water Reservoir is filled to and not beyond the MAX the Water Reservoir FILL line Return it to the brewer and ensure it is is flashing seated properly refer to page 4 e If you have completed the above procedure two times and this situation persists contact Customer Service at 1 866 901 BREW 2739 a partial cup contact Customer Service at 1 866 901 BREW 2739 The time is not The time will not be displayed on the LCD Control displayed onthe Center unless you have set it To set the clock follow LCD Control the procedure on page 10 Center e If power is interrupted to the brewer you will need to set the clock again using the procedure on page 10 Check to make sure that the Auto Off timer and or On Off time features have not been set To do this pre
24. screen at the base of your Water Reservoir empty the Water Reservoir and follow one or all of the following procedures NOTE If you are using a water filter inside the Water Reservoir remove it before cleaning Depending on the mineral content of your water calcium deposits or scale may build up in your brewer Scale is non toxic but if left unattended can hinder brewer performance Regularly descaling your brewer every 3 6 fig QD months helps maintain the heating element and other internal parts that come in contact with water Calcium deposits may build up faster READY TO BREW making it necessary to descale more often You should promptly descale if DESCALE is indicated on the LCD Control Center fig 20 However even if DESCALE is not indicated you should continue to descale your brewer every 3 6 months Properly follow the descaling procedure DE SCALE P15 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 Descaling Procedure Before you begin you will need a large ceramic mug fresh water descale solution and access to a sink Do not use a paper cup e Empty the water from the Water Reservoir If there is a Keurig Water Filter remove and set aside Disable Auto Off features if necessary refer to page 10 STEP 1 FIRST DESCALING SOLUTION RINSE e Press the Power Switch to power the brewer off Pour the entire bottle of Keurig Descaling Solution into the Water Reservoir Th
25. se the H and M buttons to advance to 12 00 AM Make sure the M button is set to 00 then change the H button When you reach 12 00 AM the LCD Control Center will indicate OFF and he function will be disabled 3 Program your brewer for a specific On Off Time NOTE To use this programming feature the clock must be set to the correct time The clock will not be displayed unless the time is set a After setting the correct time required press the MENU Button three times to program On Time feature The LCD Control Center will show the programming options with a small arrow next to SET ON TIME fig 13 READY TO BREW AUTO OFF SET BREW SIZE EXAMPLE If you chose to set the On Time at MENU Press or hold the Left Button under the H to scroll through the hours to your desired ON TIME hour 6 55 AM and the Off Time for 10 00 PM then he brewer will be READY TO BREW and maintain hot water in the tank during that ime so that it is always ready for you to brew f you wanted to brew outside this window SECTION 2 Controls amp Indicators LCD Control Center fi gt SETCLOCK AUTO OFF ONOFF TIME BREW TEMP BREW SIZE MENU simply press the Power Switch and you can brew as soon as the water is heated and the READY TO BREW indicator is displayed on the LCD Control Center NOTE The On Time and Off Time functions ope
26. ss the MENU Button and scroll through the programming options OFF should be indicated for Auto Off timer and On Off Time If OFF is not indicated follow directions on page 10 to reset Brewer shuts off or turns on automatically The water level is low and a full cup cannot be brewed Add water to Water Reservoir e If the LCD Control Center indicates PRIME please see situation to the left LCD Control Center indicates PRIME and the blue light in the Water Reservoir is flashing The blue light in Water Reservoir is flashing If any problems persist contact Customer Service at 1 866 901 BREW 2739 P18 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 SECTION 5 Warranty Limited One Year Warranty Keurig Incorporated warrants that your brewer will be free of defects in materials or workmanship under normal home use for one year from the date of purchase It is recommended that you fill out and return the warranty card enclosed with your brewer so that your purchase information will be stored in our system Keurig will at its option repair or replace a defective brewer without charge upon its receipt of proof of the date of purchase Ifa replacement brewer is necessary to service this warranty the replacement brewer may be new or reconditioned If a replacement brewer is sent a new limited one year warranty will be applied to the replacement brewer This warranty only applies to brewers opera
27. t to prevent flickering of lights blowing of fuses or tripping a circuit breaker Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is damaged in any manner Contact Keurig Customer Service to report any malfunction of or damage to the brewer Do not let the cord hang over the edge of the table or counter or touch hot surfaces 14 To disconnect press the Power Switch on the brewer to OFF status and then remove the plug from the wall outlet 15 Close supervision is necessary when any appliance is used by or near children 16 Do not lift the brewer Handle while brewing is in progress 17 Always keep the Water Reservoir Lid on the Water Reservoir unless you are refilling it 18 This appliance is equipped with a power cord having a grounding wire with a grounding plug The appliance must be grounded using a 3 hole properly grounded outlet In the event of an 2 N wo electrical short circuit grounding reduces the risk of electrical shock 19 If the outlet is a standard 2 prong wall outlet it is your personal responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet 20 Do not under any circumstances cut or remove the third ground prong from the power cord or use an adapter 21 Consult a qualified electrician if the grounding instructions are not completely understood or if doubt exists as to whether the appl
28. ted in the United States and Canada This warranty gives you specific legal rights and you may also have other rights that vary from state to state and in the case of Canada from province to province Only the use of Keurig Brewed K Cup brand packs and accessories will guarantee the proper functioning and lifetime of your Keurig brewer Any damage to or malfunction of your brewer resulting from the use of non Keurig Brewed K Cup brand packs and accessories may not be covered by this warranty or may result in a service fee if the damage or malfunction is determined to be caused by such use What is not covered by the Limited Warranty THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH OF THIS WARRANTY EVEN IF FORESEEABLE Some states or provinces do not allow the exclusion or limitations of incidental or consequential damages so the above limitation or exclusion may not apply to you depending on the state or province of purchase Nor does this warranty cover damages caused by use of non Keurig Brewed K Cup brand packs or accessories services performed by anyone other than Keurig or its authorized service providers use of parts other than genuine Keurig parts or external causes such as abuse misuse inappropriate power supply or acts of God Other Limitations THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF
29. two more times to completely purge water from internal tank If you are experiencing any problems with your brewer please contact Customer Service at 1 866 901 BREW 2739 P10 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 SECTION 2 Controls amp Indicators LCD Control Center Setting the Clock Setting the clock is optional When the clock is set the time will appear in the LCD Control Center NOTE You must set the clock if you will be using the Auto On Off Time programming feature 1 Press the MENU Button fi 2 The word OFF will appear at the top of the LCD Control Center to indicate that the clock is not set fig 10 The programming options will appear on the LCD Control Center with a small arrow pointing to SET CLOCK H Hour will appear above the Left Button ONOFF TIME and M Minute will appear above the Right aew sE Button The H and M icons and Left and Right Buttons will flash gt SETCLOCK AUTO OFF Press or hold the Left Button under the flashing H until you have reached the appropriate hour If the hour has passed 12 PM will be shown et utes 4 Press or hold the Right Button under the to set the minutes Set S Min Hours flashing 5 When you have reached the correct time press the MENU Button six times to scroll through the remaining programming steps 6 The correct time should now be display
30. ug on the Drip Tray Plate 3 Lift the Handle and the K Cup Pack Holder will open toward you fig 5 4 Select a K Cup pack NOTE Do not remove the foil lid or puncture the K Cup pack READY TO BREW eebEBP MENU j P7 201309003 KER755 K70 75 pdf 1C K ZB2319 2013 09 06 Place a K Cup pack in the K Cup Pack Holder fig 6 CAUTION There are two sharp needles that puncture the K Cup pack one above the K Cup Pack Holder and the other in the bottom of the K Cup Pack Holder To avoid risk of injury do not put your fingers in the K Cup Pack Assembly Housing Lower the Handle to close the Lid over the K Cup Pack Holder When it is closed completely the LCD Control Center will indicate READY TO BREW The Left and Right Buttons will be lit and the BREW Button will flash up to 60 seconds All brew size icons are lit with the default size flashing fig 7 To choose a different size press Left Button to go down in size or Right Button to go up in size NOTE The Small Mug is the factory set default brew size To program your favorite brew size see page 13 Programming Your Brew Size Your choices are a stronger Extra Small Cup 3 25 oz serving a Small Cup 5 25 oz serving a Small Mug 7 25 oz serving a Large Mug 9 25 oz serving or a Travel Mug 11 25 oz serving P8 201309003 KER755_K70 75 pdf 1C K ZB2319 2013 09 06 SECTION 1 Set Up amp First Brew
Download Pdf Manuals
Related Search