Kenyon B81200 Series User's Manual
Contents
1. The metal grease filters will last forever They are made of anodized aluminum It is recommended that the filters be washed at least once a month they can be washed by hand or in the dishwasher Drain water through edge holes and let each filter dry thoroughly before replacing it To Remove The Metal Grease Filters e Turn blower and lights off e Pushsimultaneously the two grease filter handles first upwards then pulltowards the center and extract the filters Figure 8 Toreinstall reverse procedure To Clean Hood Surface For general care wipe the outside of the white or black hood with sudsy water or general kitchen household cleaners rinse well and dry with clean soft cloth to avoid water marks Do not use abrasive products NOTE Turn blower and lights off Make sure the lights are cool If new lights do not operate be sure lights are inserted correctly before calling service e Remove the light shield Q by pushing simultaneously the two unlocking buttons R Figure 9 for safety reasons make sure to remove the light shield from its suspension slides G Attention When removing handle the light shield by the glass Pull out fluorescent tube and replace with Philips Type PL S 9 Watt maximum e Refit the light shield 11 LMOVB Ed 05 022. s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and the local code authorities c When cutting or drilling into wall or ceiling do not damage electrical wiring and other hidden utilities d Ducted fans must always be vented to the outdoors WARNING TO REDUCETHE RISK OF FIRE USE ONLY METAL DUCTWORK WARNING Electrical Shock Hazard Can result in serious injury or death Disconnect appliance from electric power before servicing If equipped the fluorescent lightbulb contains small amounts of mercury which must be recycled or disposed of according to Local State and Federal Codes Installation FOR RESIDENTIAL USE ONLY NOT TO BE INSTALLED OVER GAS GRILLS PLEASE READ ENTIREINSTRUCTIONS BEFORE PROCEEDING INSTALLATION MUST COMPLY WITH ALL LOCAL CODES IMPORTANT Save these Instructions for the Local Electrical Inspector s use INSTALLER Please leave these Instructions with this unit for the owner OWNER Please retain these instructions for future reference SAFETY WARNING Turn off power circuit at the service entrance and lock out panel before wiring this appliance REQUIREMENT 120 V AC 60 Hz 15 or 20 Amp Cabinet Front View 1 This hood is designed to be mounted flush to the rear wall to avoid clearance from wall to hood and to the internal sides of cabinet where ho
3. turn hood ON when cooking at high heat or when cooking flaming foods Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filter Use proper pan size Always use cookware appropriate for the size of the surface element WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE OBSERVE THE FOLLOWING a SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray then turn off the burner BE CAREFUL TO PREVENT BURNS If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT b NEVER PICK UP A FLAMING PAN You may be burned c DO NOT USE WATER including wet dishcloths or towels a violent steam explosion will result d Use an extinguisher ONLY if 1 You know you have a Class ABC extinguisher and you already know how to operate it 2 The fire is small and contained in the area where it started 3 The fire department is being called 4 You can fight the fire with your back to an exit WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING a Installation work and electrical wiring must be done by qualified person s in accordance with all applicable codes and standards including fire rated construction b Sufficient air is needed for proper combustion and exhausting of gases through the flue chimney of fuel burning equipment to prevent back drafting Follow the heating equipment manufacturer
4. KENYON SIROCCO VENTILATION HOOD OWNER S GUIDE READ AND SAVE THESE INSTRUCTIONS Models B81200 Series Important Safety Instructions Take care when using cleaning agents or detergents Select products suitable for use in household cooking area only Certain locales require make up air calculations fortotal airflow Consult your local codes and an HVAC professional before installing or using this hood CAUTION To reduce risk of fire and to properly exhaust air be sure to duct air outside Do not vent exhaust air into spaces within walls or ceilings or into attics crawl spaces or garages CAUTION For General Ventilating Use Only Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING a Use this unit only in the manner intended by the manufacturer If you have questions contact the manufacturer b Before servicing or cleaning unit switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel WARNING TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE Never leave surface units unattended at high settings Boilovers cause smoking and greasy spillovers that may ignite Heat oils slowly on low or medium settings Always
5. L GROUNDINGINSTRUCTIONS THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION BOX WITH 3 WIRES ONE OF WHICH GREEN YELLOW SERVES TO GROUND THE APPLIANCE TO PROTECT YOU AGAINST ELECTRIC SHOCK THE GREEN YELLOW WIRE MUST BE CONNECTED TO THE GROUNDING WIRE IN YOUR Side Spring HOME ELECTRICAL SYSTEM AND IT MUST UNDER Figure 6 NO CIRCUMSTANCES BE CUT OR REMOVED Warning Turn off power circuit atthe service panel before wiring Cabinet Door this unit 120 VAC 15 or 20 Amp circuit required a Remove j box cover as shown in Figure 8 Fixing ie 5 a R i i i i point 1 2 fg Zuger b Remove the knockout and install the strain relief conduit un i F point 1 2 connector 1 2 in junction box Template Cutout ior c Run 3 wires black white and green 16 AWG in 1 2 WG 5 Duct conduit from service panel to junction box Backside d border Connect black wire from service panel to black or red in junction box white to white and green to green yellow See Backside of Blind hole the cabinet Side Springs Figure 8 Figure 7 Housing e Close junction box cover Conduit Figure 8 Figure 8 Box adjustment The hood can be installed in cabinets with different depths see also figure 1 for details however the front of the slider box must always be flush with the front of the cabinet For alignment adjust the back stops of the box For box adjustment loose
6. ansition fixing screw and 4 spacers e Remove the light shield unscrew and remove lamps to prevent damage when installing see paragraph on Light Figure 5 NS replacement for details gt Pulloutthe slider and remove the grease filters see paragraph To remove the grease filters for details Fitthe transition on the outlet hole of the hood This has a bayonet lock and must be fixed to the hood with one screw Figure 5 check the opening and closing of the damper mounted inside Installation Install the Hood Set the motor housing into the opening e Pushthe spring inside the motor housing using a screw driver as a lever from the inside of the motor housing Insertitcompletely in place taking care to snap sides springs into the blind holes made fortemporary fixing and that conduit and duct section if already fitted run freely across the cut outs on top of the cabinet see figure 6 Fixthe hood permanently with two screws 4 5x16 per side to be inserted frome the inside ofthe hood to the corresponding side fixing points 1 and 2 drilled on the cabinet see figure 7 e Connect a 5 duct to the transition and seal with tape e Connect to power supply Attention While mounting the hood on the wall cabinet be sure once the hood has been fastened that the wiring compartment is easily and safely accessible in order to make safety inspections and or maintenance operations Cabinet WARNING ELECTRICA
7. e Anon return smoke damper is supplied mounted on the transition 5 Hood installation height above cooktop is at the users preference Do not consider the door of the cabinet Use spacers for 1 4 wider cabinet Cabinet Right Left Side View The lower the hood above the cooktop the more efficient the min Depth of capturing of cooking odors grease and smoke Werecommendthat Recessed the hood be installed 18 to 36 over an electric cooktop and 25 to Area 7 112 36 over a gas cooktop Be sure that your hood model fits your Door n installation Fixing of Recessed Basic llation S Point 1 Were asic Installation teps Fixing Foreasiestinstallation thehood should be installed in the cabinet FO YE af before mounting the cabinet to the wall In any case the installation pee steps do notchange Tools required for installation Screw driver philips 1 Electric drill Figure 1 with twist bit 5 64 and 7 32 or 75 64 er Pin Housing Tape F 0 This Hood can easily be installed following these basic steps E 0 en Housing P h 7 E Spacer PS i ixing Points repare the cabinet cut out bottom and top of the cabinet as required and mark fixing points Spacer i Snap Spacer for 1 4 i Pins Into Their Runconduit and duct sections to the hood and make connections wider AO Housings Fix the hood to the cabinet cabinet Mount the cabinet on the wall e Connectductto the outside and conduit sectio
8. n screws M slide the square plates P as necessary and tighten screws M Figure 8 Ensure that the drawer when fully retracted turns OFF all power by acting positively on the rear microswitch Final installation steps Insert lamps in place Fit the Lamp Shield Fit the Grease Filters Check all light bulbs to make sure they are secure in their sockets then turn power on in service panel and check lights and blower operation per Use amp Care section of this manual and install filters Make sure to leave this manual for the home owner Use and Care READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE RANGE HOOD i For satisfactory use of your hood become familiar with the various functions Control Pad Functions of the hood as described below Air outlet Motor Housing Light OFF Light ON Slider Box N Left Grease Filter zn Grease High Speed Handles Handles Medium Speed Low Speed nen Filters p Blower OFF Figure 7 Operating Instructions The blower should be turned on for about 5 minutes before cooking in order to establish air currents upward through the hood Use the low speeds for normal use and the higher speeds for strong odors or fumes Minimize cross drafts which will reduce the effectiveness of the hood Hood Cleaning Figure 8 Lights replacement Figure 9 Be sure lights are cool before cleaning the hood To Clean Filters
9. n tothe service panel 3 Figure 2 Installation Pre de Prepare the cabinet for installation 16 24 Model i i 28 7 16 30 Model _ Mark and cut out the cabinet bottom as shown in figure 3 34 7 16 36 Model Fit the template which comes with the hood on the inner __Rearside lof the Cabirlet right side of the cabinet making sure the side with arrows matches with the lower edge of the cabinet andthe rear edge max 13 3 46 CUT OUT of the cabinet or cut out min 10 13 48 j SE Cabinet L Door Do not consider the Door of the Cabinet Add 4 46 when using Spacers Rearside of the Cut Out for cabinet deeper Figure 3 than 13 3 46 without considering the door Cabinet e Drill 2holes see figure 4 fixing point 1 and 2 and 1 blind Door m 64 hole in diameter in depth e Move template to the other side and repeat Make cut out for duct and conduit see figure 1 Fixing Fixing 0 point 1 2 Template OA cutout for Template 1 2 Conduit Se Duct FSR SEE of the cabinet Se border Backside of Blind hole the cabinet Side Springs Housing Figure 4 Prepare the hood for installation Remove the hood from packaging check its condition and make sure the following pieces are included 1 hood 1 registration card 1 instruction manual 1 template 1 transition with damper 1 plastic bag with 4 hood fixing screws 1 tr
10. od must be fixed for this reason we suggest installing this hood only inside a cabinet having an intemalwidthof22 forthe24 Model 287 forthe 30 Model 34 forthe Fixing i is i 36 Modelandwithaninternaldepthofminimum7 Seefigure Point 1 A Point The external depth of the cabinet must be minimum 10 and Fixing Fixing maximum 13 See figure 1 Point ZX T Point 2 Attention Do not consider the door of the cabinet when measuring The appliance is also supplied with 4 spacers that can be snapped at fixing point 1 and 2 cabinets wider can be Cabinet Top View used see figure 2 Internal Width 2 For the most efficient air flow exhaust use a straight run or as few 3 me or ace elbows as possible he 36 Model CAUTION Vent unit to outside of building ONLY 13 4 Rearside of the Cabinet Hoo 3 Ifallowed in your area use metallic flex ducting only to connect rigid ae fe 13 6 duct directly to transitions max 13 3 46 TI i a 4 COLDWEATHER installations should have an additional backdraft min 10 8 18 SEE are damper installedto minimize backward cold air flow and a nonmetallic 5 Duct thermal break to minimize conduction of outside temperatures as Eh part of the ductwork The damper should be on the cold air side of a e 8 Door the thermal break The break should be as close as possible to where the ducting enters the heated portion of the hous
Download Pdf Manuals
Related Search