Home

Kenwood 411 User's Manual

image

Contents

1. A Keep the assist grip in a safe place If you have difficulty removing the assist grip contact an authorized Kenwood dealer SK 701RM INSTALLATION GUIDE Screw hole Original assist grip screw Mountin Bracket Cut the Sleeve 1cm shorter than the length between Mounting Brackets A Slip the sleeve over the end of the Grab Handle opposite the warning label Make sure that TOP is on the upper side Attach Mounting Brackets A using the original assist grip screws Torque 1 45 1 81 ft lb Use a torque meter to measure proper torque Original assist grip Screw hole Mounting Bracket A Be sure to install the sleeve so that the warning label will be visible after the installation is complete Xf it is difficult to insert use the liquid soap provided XB careful not to use too much liquid soap Don t get any of the liquid soap on the seats or other upholstrey If the liquid soap goes into your eyes rinse with plain water Don t rub your eyes O Liquid soap Sleeve 6 Insert the Grab Handle through Mounting Brackets B Tighten screws to fix Mounting Brackets B to Mounting Bracket A i When the gap between Mounting Torque 1 45 1 81 ft lb Use a torque meter to measure proper torque Brackets A is small use a stub driver Hae Mounting Bracket B Mounting Bracket A diaa Stub driver To prevent injury en
2. KENWOOD REAR MONITOR MOUNTING KIT SK 701RM PRINTED in the USA INSTALLATION MANUAL PK 0089 PARTS LIST Mounting Bracket A Mounting Bracket B Monitor Mount Grab Handle 22 7 8 Ss Universal Monitor Allen Screw A Alien Wrench Liquid Soap W6XB AN CAUTION To ensure safe installation of the mounting kit adjust either the front seat or the mounting kit to prevent contact with front seat occupants To minimize the risk of improper installation and potential injuries Kenwood recommends that the Installation of this unit be performed by a professions Screws must be tightened with the indicated torque X1 This product must be used only as a monitor mount Maximum weight for the Grab Handle is 22 Ib Do not hang from It or subject it to unnecessary weight Installation must be periormed according to this installation manual Kenwood is not responsible for injuries arising from installations not performed strictly in accorcance with the procedures in this manual This product is designed to be used with a monitor that is no iarger than 8 3 x 5 3 x 1 6 in weighing 1 25 Ib or less 8 inch wide monitor For rear seat installation only The monitor must not be visible te the driver X1 What is torque The force required to tighten something is called torque An adult using a normal screw driver handle dia 3Omm exerts a force approx 0 72 1 45 ft lb Use a
3. torque meter to measure torque during the installation BEFORE YOU BEGIN FITTING EXAMPLE The example figure shows an installation in the rear left side of a vehicle TOOLS 1 Screw driver No 2 No 3 2 Stub driver No 3 9 Scissors or Cutter AX If you can t remove the assist grip screw by using the above mentioned tools please ask your local dealer ZX To prevent damage to the car or product use the proper tools Ensure sufficient torque is exerted to tighten the screws REGULAR INSPECTION To ensure continued safe operation inspect the mount according to the following schedule If any mounting screws have loosened tighten them to the proper torque tevel see other side for details r Inspect every month or immediately Inspect Inspect Mer after driving on a rough road every 6 months jevery year Remarks Monitor looseness O O O Refer to Step 5 Ji ee AAA SESS E AE eA eg ie ele er el eter eke eee ee ee Vehicle mounting area looseness O Refer to Step Ma ee X2 Itis especially important to inspect the mount after driving off road or on mountain roads Vehicle mounting area looseness Holder contact looseness Pipe contact looseness Monitor looseness REMOVING THE ASSIST GRIP Assist grip Remove the assist grip according to the iNustration at the left Keep the original screws don t discard them thay will be used to install the monitor mount
4. sure that Mounting Brackets B are fixed as close as possible to the vehicle s interior surface Mountin Bracket Mounting Bracket A z Mounting Bracket Grab Handle Sleeve Grab Handie www kenwoodusa com 1 800 KENWOOD KENWOO Copyright 2002 Kenwood USA Corp All rights reserved Attach the Monitor Mount to the Grab Handle Fix end caps to the Grab Handle End cap Grab Handle End cap Monitor Mount Allen screws must be tightened until the Grab Handle is indented Grab Mountiny Og Handie Attach the monitor Adjust the position Fix with Ailen screws tackot Torque 1 81 2 17 ft lb Use a torque meter to measure proper torque Refer to the monitor s manual for detailed information Mountin Bracket If the manitor doesn t have a rall use Universal Monitor Mount Allen Screw Monitor Universal Monitor Monitor To prevent the monitor from detaching Rotate the rail guide so it fits the rail you tighten knobs A and B securely Install the monitor so that its top surface presses against the headliner are using Using Universa RNN Using rail of monitor Monitor Mount Monitor Mount i yo Le 3 XS F amp S Monitor Rail Gulde Rail Guide Monitor

Download Pdf Manuals

image

Related Search

Related Contents

HL-EL010 取扱説明書  Affichage  SoftWall Finishing Systems SW3223352048 Instructions / Assembly  Rexel RDM1150  【37520】ドラえもん うごくおえかき  USER GUIDE CLINIGEL - Orion Laboratories Pty Ltd  

Copyright © All rights reserved.
Failed to retrieve file