Kenmore 30'' Chimney Range Hood Installation Guide
Contents
1. HOOD DISTANCE ABOVE 36 COOK TOP SEE NOTE 1 NOTES Minimum hood distance above cooktop must not be less than 24 A maximum of 30 above the cooktop is highly recommended for best capture of cooking impurities Distances over 30 above the cooktop are at the installer s and user s discretion providing that ceiling height and flue length permit MOUNTING BRACKET LOCATION ABOVE 36 HIGH COOK TOP INSTALL UPPER FLUE MOUNTING BRACKET If a framing member is not present drill two N N6 diameter holes where shown Insert dry wall anchors into the holes Center the bracket over the hood location and flush with the ceiling Make sure that the slots of the upper flue bracket are at the bottom Secure the upper flue bracket to the wall using 2 8 x 1 2 mounting screws Tighten the screws completely Make sure that the bracket is tight against the wall Center of installation Ceiling a a IDILI III Ak A AAA A DDD D DIED he nn Recommended distance between i y screw _ A 53 y ue 5 16 TYP Flush with Center of the ceiling Ceiling installation Upper flue mounting bracket slots INSTALL THE WIRING GROUNDING INSTRUCTIONS This appliance must be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric current This appliance is equipped with a cord having a grounding wire with2. 7 Damage to or failure of parts or systems result ing from unauthorized modifications made to this product Disclaimer of implied warranties limitation of remedies Customer s sole and exclusive remedy under this limited warranty shall be product repair as pro vided herein Implied warranties including warran ties of merchantability or fitness for a particular purpose are limited to one year or the shortest period allowed by law Sears shall not be liable for incidental or consequential damages Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages or limitation on the duration of implied warranties of merchantability or fitness so these exclusions or limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Sears Brands Management Corporation Hoffman Estates IL 60179 OPERATION CONTROLS OOOO 0 OFF LO MED 9 This hood is operated using 5 pushbuttons on the front of the hood canopy The fan OFF pushbutton turns the fan off The fan low medium and high speed pushbuttons turn the fan on to three different speed settings The light pushbutton turns the lights on and off LIGHT BULBS CAUTION A Bulbs may be hot Always allow bulbs to cool down before removing them This range hood requires two incandescent bulbs Type B10 120V 40W Max candelabra To in
3. CONNECTOR Flat Head Flat Head GLASS 7 DRYWALL CANOPY ANCHORS 2 BULBS B10 120V UPPER 40W MAX FLUE MOUNTING eee ee BRACKET oo HOUSING A HOOD LOWER MOUNTING BRACKET 4 DECORATIVE WASHERS FLUE MOUNTING BRACKET PARTS NOT INCLUDED WITH HOOD NON KIT KENMORE PART NO 59921 NON DUCTED NON DUCT Eo PLENUM 9 FT CEILING FLUE EXTENSION KENMORE PART NO 59920 T NON DUCT PLENUM COLLAR 2 TIE FLEXIBLE DUCT WRAPS NO 8 x 3 8 Pan Head Parts Not Included With Hood are available by 4 calling 1 800 4 MY HOME EQUIVALENT DUCT LENGTH CHART Kenmore range hoods are designed to perform efficiently when attached to long runs of duct As a point of reference this hood will function at approximately 80 of its rated air flow when 150 equivalent feet of 6 g round ductwork is attached Use this chart to calculate the equivalent duct length of your system 2 lt Kenmore Model Broan Model 428 59691 3V4 in x 10 in 6 in Round Right angle Elbow Wall Cap Equivalent length Equivalent length Broan Model 401 8 5 ft 34 ft Straight Duct 6 ft w o damper g 3Y in x 10 in x 2 ft long Q Equivalent length Broan Model 429 9 2 ft 3V4 in x 10 in lt Right angle Flat Elbow See Equivalent length 59391 24 ft 3Y in x Broan Model 406 were Straight Duct Es Equivalent O 6 in round x 2 ft long Broan Model 430 length y Equivalent length 314
4. Note When replacing bulbs remove the non ducted filter if installed to ease lamp installation GREASE FILTER INSTALL DUCT CONNECTOR 1 Install damper duct connector to top of hood using 4 48 x 3 8 pan head mounting screws Note Damper flaps must be removed and discarded for non ducted installations DAMPER FLAPS 4 N 8 X 3 8 PAN HEAD SCREWS ya N pe ge DAMPER DUCT CONNECTOR 1 LOWER FLUE m MOUNTING Make INSTALL THE HOOD HORIZONTALLY DUCTED HOODS ONLY DO NOT REMOVE the protective plastic film covering the decorative flues at this time BRACKET 814 MAX sure there will be adequate clearance between top of hood and lower flue mounting bracket for ductwork Elbow must be located below lower flue mounting bracket Align the hood and center it above the MASS hood mounting bracket Gently lower the hood until it securely engages the bracket INSIDE BACK OF HOOD MOTOR BLOWER ASSEMBLY 5 16 HOLE LOCATIONS If a framing member is not present With the hood hanging in place drill through both holes located in the inside lower back of hood using a 5 16 drill bit Insert the included drywall anchors into the drilled holes one for each hole Install 2 washers and 2 8 x 1 2 mounting screws through the back of the hood and into the drywall anchors Verify that the hood
5. as frying and wok cooking Turn the filter mounting tabs to remove filter and replace STAINLESS STEEL CLEANING DO e Regularly wash with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent e Always clean in the direction of original polish lines Always rinse well with clear water 2 or 3 times after clean ing Wipe dry completely e You may also use a specialized household stainless steel cleaner DONT Use any steel or stainless steel wool or any other scrapers to remove stubborn dirt Use any harsh or abrasive cleansers Allow dirt to accumulate Let plaster dust or any other construction residues reach the hood During epee clap nacion cover the range hood to make sure no dust sticks to the stainless steel surface Avoid When choosing a detergent po cleaners that contain bleach will attack stainless steel products containing chloride fluoride iodide bromide AIE surfaces rapidly e Any combustible products used for cleaning such as ac etone alcohol ether benzol etc are highly explosive and should never be used close to a range TOOLS NEEDED FOR INSTALLATION LES Screwdriver Wire Sabre or i Flat amp Stripper Saw Phillips QQ x Tape Pencil Duct Measure Drill PARTS INCLUDED WITH HOOD 8 MOUNTING SCREWS 8 x 3 8 Pan Head MOUNTING SCREWS CS M4 X 1 in A RUBBER DECORATIVE FLUE pi RUBBER 7 MOUNTING SCREWS DAMPER DUCT 8 X 1 1 2
6. for best capture of cooking impurities Distances over 30 are at the installer and users discre tion providing that the ceiling height permits ROUND DUCT ROOF CAP ROUND ELBOW 6 Da __ WALL CAP HOOD MOUNTING i BRACKET DECORATIVE L FLUE 12 3 4 TO CENTER OF HOOD MOUNTING BRACKET HOLES y HOOD _ 24 To 30 ABOVE DUCT COOKING SURFACE CENTER LINE INSTALL MOUNTING BRACKET 1 Construct wood wall framing that is flush with interior surface of wall studs Make sure a the framing is centered over installation location b the height of the framing will allow the mounting bracket to be secured to the framing within the dimensions shown 2 After wall surface is finished carefully center and level the hood mounting bracket and secure it to wall framing with 3 8 x 1 1 2 mounting screws Tighten the screws completely Note Do not use drywall anchors CEILING DUCT HEIGHT METHOD 8 FEET DUCTED OR reer NONDUCTED 36 3 4 37 3 4 38 3 4 39 3 4 40 3 4 41 3 4 42 3 4 9 FEET DUCTED OR 3 47 3 4 3 4 3 4 40 3 4 41 3 4 42 3 4 WITH OPTIONAL FLUE EXTENSION PART NUMBER 59920 WALL STUDS romo BEHIND DRYWALL WA 363 4 bottom of hood 24 above cooktop 423 bottom of hood 30 above cooktop MOUNTING BRACKET LOCATION ABOVE 36 HIGH COOKTOP
7. in x 10 in AS tt 2 ft gt Right angle 7 ft w o S dl Short damper S Eave Elbow Broan Model 419 Equivalent length 6 in Round Elbow 15 ft Equivalent length 8 ft Kenmore Model 59581 3V4 in x 10 in to 6 in Round Transition Equivalent length 5 5 ft Kenmore Model bucting 1 800 Broan Model 431 34 in x 10 in Right angle Long Eave Elbow Equivalent length 15 ft Kenmore Model 59091 Roof Cap accepts 7 in round or 3V4 in x 10 in duct Equivalent length 30 ft 7 ft w o damper ccessories are available by calling 4 MY HOME Broan Model Ducting Accessories are available by calling 1 800 558 1711 Buluba gt 7 4 a o p o SJIDg SIAJOS INSTALL THE DUCTWORK WARNING dh To reduce the risk of fire use only metal ductwork 1 Decide where the ductwork will run between the hood and the outside 2 A straight short duct run will allow the hood to perform most efficiently 3 Long duct runs elbows and transitions will reduce the performance of the hood Use as few of them as possible Larger ducting may be required for best performance with longer duct runs A Install a wall cap or roof cap Connect round metal ductwork to cap and work back towards the hood location Use duct tape to seal the joints between ductwork sections The minimum hood distance above cooktop MUST NOT BE LESS than 24 A maximum of 30 above cooktop is highly recom mended
8. this unit only in the manner intended by the manufac turer If you have questions contact the manufacturer at the address or telephone number listed in the warranty Before servicing or cleaning unit switch power off at service panel and lock service disconnecting means to prevent power from being switched on acciden tally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel Installation work and electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards including fire rated construction codes and standards Sufficient air is needed for proper combustion and exhausting of gases through the flue chimney of fuel burning equipment to prevent backdrafting Follow the heating equipment manufacturer s guidelines and safety standards such as those published by the National Fire Protection Association NFPA the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and the local code authorities This product may have sharp edges Be careful to avoid cuts and abrasions during installation and cleaning When cutting or drilling into wall or ceiling do not dam age electrical wiring and other hidden utilities Ducted fans must always be vented to the outdoors Use only metal ductwork Do not use this unit with any other solid state speed control device 10 This u
9. 7686 Upper Flue Mounting Bracket 13 99527666 User Interface Cable l 14 99528337 Trim l 15 99527663 Plastic Cover I 99527662 Capacitor I 17 99527687 Lower Flue Mounting Bracket 99271492 40W 120V B10 Candelabra Bulb not shown 2 99527664 Parts Bag not shown I 99528459 Non Duci Filter Clips not shown l Order service parts by Part No not by Key No 12 Get it fixed at your home or ours Your Home For troubleshooting product manuals and expert advice managemylife www managemylife com For repair in your home of all major brand appliances lawn and garden equipment or heating and cooling systems no matter who made it no matter who sold it For the replacement parts accessories and owner s manuals that you need to do it yourself For Sears professional installation of home appliances and items like garage door openers and water heaters 1 800 4 MY HOME 1 800 469 4663 Call anytime day or night U S A and Canada www sears com www sears ca Our Home For repair of carry in items like vacuums lawn equipment and electronics call anytime for the location of your nearest Sears Parts amp Repair Service Center 1 800 488 1222 U S A 1 800 469 4663 Canada www sears com www sears ca To purchase a protection agreement on a product serviced by Sears 1 800 827 6655 U S A 1 800 361 6665 Canada Para pedir servicio de reparaci n a domicilio y para ordenar piezas 1 888 SU HOGA
10. LY DUCTED HOODS ONLY 1 DO NOT REMOVE the protective plastic film covering the decorative flues at this time 2 Align the hood and center it above the hood mounting bracket Gently lower the hood until it securely engages the bracket INSIDE MOTOR a Y 7 g y j Ra rs HOLE LOCATIONS ee 3 If a framing member is not present With the hood hanging in place drill through both holes located in the inside lower back of hood using a 5 16 drill bit Insert the included drywall anchors into the drilled holes one for each hole 4 Install 2 washers and 2 8 x 1 2 mounting screws through the back of the hood and into the drywall anchors Verify that the hood is centered and leveled Tighten all screws completely 6 ROUND DUCT VERTICAL DUCTING 5 Measure and cut metal ductwork Set ductwork aside 6 Plug hood power cord into the outlet 10 LOWER FLUE MOUNTING BRACKET y y gt gt LOWER FLUE 7 Remove the upper flue from inside the lower flue Install the lower flue bracket to the lower flue using 2 flue bracket screws 8 x 3 8 Ensure that the bracket is positioned inside of the lower flue flanges with the slots on top Carefully replace the upper flue inside the lower flue Remove protective plastic film covering the lower flue only 8 Place both flues into the recessed area of hood top 9 Carefully rotate botto
11. R 1 888 784 6427 E Sons Registered Trademark Trademark of KCD IP LLC in the United States or Sears Brands LLC in other countries Marca Registrada Marca de F brica de KCD IP LLC en Estados Unidos o Sears Brands LLC in otros pa ses MC Marque de commerce MP Marque d pos e de Sears Brands LLC Au Canada pour service en francais 1 800 LE FOYER 1 800 533 6937 WWW sears ca
12. To arrange for warranty service call 1 800 4 MY HOME 1 800 469 4663 For one year from the date of purchase any part of this product that fails due to a defect in material or workmanship will receive free repair or replacement if repair proves impossible The length of this coverage does not apply to the finish of any painted or bright metal part e For thirty days date of purchase any painted or bright metal part of this product will be replaced free of charge if its finish is defective in material or workmanship All warranty coverage is void if this product is ever used for other than private household purposes This warranty covers only defects in material and workmanship and will NOT pay for 1 Consumable parts that can wear out from normal use including but not limited to filters belts light bulbs and bags A service technician to instruct the user in cor rect product installation operation or mainte nance A service technician to clean or maintain this product Damage to or failure of this product if it is not installed operated or maintained according to the all instructions supplied with the product Damage to or failure of this product resulting from accident abuse misuse or use for other than its intended purpose Damage to or failure of this product caused by the use of detergents cleaners chemicals or utensils other than those recommended in all instructions supplied with the product
13. Use amp Care Installation Manual Manual de Uso y Cuidado Instalaci n English Espa ol Models Modelos 233 5992 5993 Kenmore Range Hood Campana de cocina color number n mero de color P N 99528329E Sears Brands Management Corporation Hoffman Estates IL 60179 USA www kenmore com www sears com De e READ AND SAVE THESE INSTRUCTIONS TABLE OF CONTENTS Safety Instr cti ns viii ia 2 WVUITON Y ssssacscdessisss E csssoassacessessecsassensees 3 OP GLOTION esse snsssctansesevcscssnsarcrsrsnicevdcuccsaversenseseususeuesnsapensureuedeve 3 ETA secede seacansiddossassuncusuenesen vanes 4 Parts eluded With HOO A essi assos teoses eaae sas 4 Parts Not Included With Hood esessesssseesseseseecessessseesesessee 4 Tools Needed EEE T E EE EE EA 4 SECTION sre a PAGE Equivalent Duct Length Charts sisssisssisssersssissssssssisisesssissssse 5 Prepare The Hood Location cccocconiononnnnannnnonannonnanionanionasos 6 Prepare The HOO sssissicccssctccctcscsivensevsicccsestessssstenstescssusanve 7 8 Connect The Wiring sssiessescsscectscssebecstzcescocacecsssectecdtveceacessazes 9 Install The HOGG wwsccscsccsscssdccscssaderteacccescsdseassavisess 9 10 11 12 Service POMS ii ccssessvsntsrecescsaccasevsacoinsticvesdstennsteereesencesseaosentoaes 12 SAFETY INSTRUCTIONS FOR DOMESTIC COOKING ONLY WARNING A TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSON S OBSERVE THE FOLLOWING 1 Use
14. a grounding plug The plug must be plugged into an outlet that is properly installed and grounded Position the electrical outlet within the space covered by the decorative flue and where it will not interfere with the round duct Make sure the outlet does not interfere with the mounting bracket fastening area ductwork or where the decorative flue touches the wall BACK OF HOOD LOCATE ELECTRICAL OUTLET WITHIN THESE AREAS Verify location will not interfere with duct mounting brackets and flue gt 7 4 a o o SJIDg SIAJOS INSTALL CURVED GLASS PLATE 1 Place range hood body on its back with controls 4 facing up Place cardboard under hood to protect M4 X 1 IN countertop or table finish SCREWS 2 Position the curved plate glass over the range hood BLACK body as shown 3 Install rubber bushings into all 4 holes of the glass 4 Place a plastic decorative washer onto 4 M4 x l in flathead mounting screw ps 5 Align holes in glass with holes in the range hood body Install and fasten 4 black flat head screws with decorative washers through rubber bushings BUSHINGS _ and into the range hood body 7 6 Hand tighten screws but do not overtighten INSTALL BULBS 1 Remove the grease filter by pushing in the metal latch tab Pull filter out to remove NON DUCT 2 Install 2 Type B10 40 Watt maximum incandes FILTER cent candelabra bulbs included
15. connector with a tie wrap Attach flexible duct to non duct plenum collar and secure with tie wrap Tape all joints with duct tape Remove protective plastic film covering the lower flue only Carefully place both flues into the recessed area of hood top 10 Attach non duct plenum with collar to upper flue using 4 8 x 3 8 pan head screws Hold hood up close to wall mounting location and plug power cord into wall outlet 12 Align the hood and center it above the hood mounting bracket Gently lower the hood until it securely engages the bracket 13 1f a framing member is not present wi te INSIDE hood hanging OF in place drill HOOD MOTOR through both holes located in the inside lower back of hood using a 916 drill bit Insert the included drywall anchors into the drilled holes one for each hole ASS 5 16 HOLE LOCATIONS Ple 14 Install 2 washers and 2 8 x 1 1 2 mounting screws 15 Slide up the upper flue 16 through the back of the hood and into the drywall anchors Verify that the hood is centered and leveled Tighten all screws completely UPPER FLUE MOUNTING until it is aligned with its BRACKET FRONT VIEW mounting bracket The bracket should be inside the flue Secure the upper flue on the upper flue mounting bracket using 2 8 x 3 8 mounting screws Remove protective plastic film co
16. gt 3 9 For indoor use only For general ventilating use only Do not use to exhaust haz ardous or explosive materials and vapors To avoid motor bearing damage and noisy and or unbal anced impeller keep drywall spray construction dust etc off power unit Do not use over cooking equipment greater than 60 000 BTU hr as the blower motor will shut down intermittently Your hood motor has a thermal overload which will auto matically shut off the motor if it becomes overheated The motor will restart when it cools down If the motor continues to shut off and restart have the hood serviced The bottom of the hood MUST NOT BE LESS than 24 and at a maximum of 30 above cooktop for best capture of cooking impurities Two installers are recommended because of the size of this hood To reduce risk of fire and to properly exhaust air be sure to duct air outside Do not exhaust air into spaces within walls or ceilings or into attics crawl spaces or garages Be careful when installing the decorative flue and hood they may have sharp edges 10 Please read specification label on product for further infor mation and requirements INSTALLER Leave this guide with the homeowner HOMEOWNER Operation and maintenance information on page 2 KENMORE LIMITED WARRANTY When this appliance is installed operated and maintained according to all supplied instructions the following warranty coverage applies
17. is centered and leveled Tighten all screws completely 6 10 12 Remove the upper Remove protective Measure and install 6 round metal ductwork to roof cap or wall cap and 90 elbow over duct collar on hood Use duct tape to make all joints secure and air tight Plug hood power cord into the outlet 6 ROUND ELBOW LOWER FLUE flue from inside MOUNTING BRACKET the lower flue 1 1 Install the lower y y flue bracket to the lower flue using 2 flue bracket screws 8 x 3 8 Ensure that the bracket is positioned inside of the lower flue flanges with the slots on top Carefully replace the upper flue inside the lower flue Remove protective plastic film covering the lower flue only LOWER FLUE Carefully place both flues into the recessed area of hood top Slide the upper flue upward until it is aligned with its upper flue mounting bracket The bracket should be inside the flue Secure the upper flue to the upper flue mounting bracket using 2 8 x 3 8 mounting screws UPPER FLUE MOUNTING BRACKET FRONT VIEW plastic film covering the upper flue and the hood Reinstall grease filter by aligning rear filter tab with slot in the hood push in the metal latch tab push filter into position and release Make sure filter is securely engaged after installation P 7 4 a o p o SJIDg SIAJOS INSTALL THE HOOD VERTICAL
18. m of flue assembly out and slide metal duct section into flue assembly UPPER FLUE MOUNTING BRACKET FRONT VIEW 10 Connect duct section to duct connector and duct rough in Use duct tape to make sure all joints are secure and air tight 11 Slide the upper flue upward until it is aligned with its upper flue mounting bracket The bracket should be inside the flue Secure the upper flue to the upper flue mounting bracket using 2 8 x 3 8 mounting screws 12 Remove protective plastic film covering the upper flue and the hood 13 Reinstall grease filter by aligning rear filter tab with slot in the hood push in the metal latch tab push filter into position and release Make sure filter is securely engaged after installation Note INSTALL THE HOOD NON DUCTED HOODS ONLY Purchase Non Duct Kit Kenmore part number 59921 1 Remove CAUTION Use only expandable aluminum duct provided with non duct kit Do not remove the protective plastic film covering the decorative flue at this time from and damper flaps damper duct connector discard flaps NON DUCT PLENUM __ NON DUCT COLLAR 7 6 ALUMINUM FLEX DUCT DAMPER DUCT CONNECTOR Attach non duct collar to non duct plenum using 4 48 x 3 8 pan head screws Measure distance A Cut a length of flexible metal duct extended to this dimension Attach aluminum flexible duct to the damper duct
19. nit must be grounded Te REDUCE THE RISK OF A RANGE TOP GREASE FIRE Never leave surface units unattended at high settings Boilovers cause smoking and greasy spillovers that may ignite Heat oils slowly on low or medium settings Always turn hood ON when cooking at high heat or when cooking flaming foods i e Cr pes Suzette Cher ries Jubilee Peppercorn Beef Flamb 3 Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filters 4 Use proper pan size Always use cookware appropriate for the size of the surface element TO REDUCE THE RISK OF INJURY TO PERSON S IN THE EVENT OF A RANGE TOP GREASE FIRE OBSERVE THE FOLLOWING N w gt OON Q N 1 w gt a WH ON SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray then turn off the burner BE CAREFUL TO PREVENT BURNS IF THE FLAMES DO NOT GO OUT IM MEDIATELY EVACUATE AND CALL THE FIRE DEPARTMENT NEVER PICK UP A FLAMING PAN You may be burned DO NOT USE WATER including wet dishcloths or towels This could cause a violent steam explosion Use an extinguisher ONLY if You know you have a Class ABC extinguisher and you know how to operate it The fire is small and contained in the area where it started The fire department has been called You can fight the fire with your back to an exit Based on Kitchen Fire Safety Tips published by NFPA CAUTION A
20. stall or change bulbs 1 Remove grease filter by pushing in the metal latch and tilting filter down 2 If non duct filter is installed remove filter by turn ing filter mounting tabs 3 Remove and discard bulb Replace with new bulb A Re install non duct filter if applicable 5 Re install grease filter A1930S 5 3 S lt uopiadO Bulupe gt 5 a 4 a o Oo 3 SJIDJ SIAJOS CLEANING Proper maintenance of the Range Hood will assure proper performance of the unit MOTOR The motor is permanently lubricated and never needs oiling If the motor bearings make excessive or unusual noise replace the motor with the exact service motor The impeller should also be replaced GREASE FILTER The grease filter should be cleaned frequently Use a warm dishwashing detergent solution Grease filter is dishwasher safe Clean all metal filters in the dishwasher using a non phosphate detergent Discoloration of the filter may occur if using phos phate detergents or as a result of local water conditions but this will not affect filter performance This discoloration is not covered by the warranty Remove grease filter by pushing in on the metal latch tab This will disengage the filter from the hood Tilt the filter downward and remove NON DUCTED RECIRCULATION FILTER The non ducted recirculation filter should be changed every 6 months Replace more often if your cooking style generates extra grease such
21. vering the flue and the hood NON DUCT FILTER MOUNTING R 17 18 l METAL e LATCH NON DUCT ECIRCULATION FILTER Install the non duct recirculation filter as shown Turn mounting tabs on hood to secure filter Reinstall grease filter by aligning rear filter tabs with slots in the hood Push in the metal latch tab push filter into position and release Make sure filter is securely engaged after installation 11 uoojjo su S Dd 29141 INSTALL FLUE EXTENSION FOR 9 FT CEILINGS Note 9 ft ceilings require the purchase of a flue extension Kenmore part number 59920 1 Discard the upper flue supplied with the hood and replace it with the longer flue section 2 Follow all steps shown in the section INSTALL THE HOOD for horizontal vertical and non ducted installations SERVICE PARTS Models 233 5992 5993 color number a KEY PARTNO DESCRIPTION QTY MS 1 99527669 Decorative Upper and Lower Flues l IM 2 99528334 Motor Blower Assembly I 3 99527659 Light Socket Assembly Harness l ne 4 99526976 User Interface Assembly 5 99527658 Aluminum Grease Filter 6 7 99527023 Non Duct Recirculation Filter 99528335 Curved Glass Plate 30 99528336 Curved Glass Plate 36 I 8 99526983 Damper Duct Connector l 9 99526984 6 Dia Expandable Flexible Aluminum Duct 1 10 99527670 Non Duct Plenum Assembl l 11 99527685 Hood Mounting Bracket I 12 9952
Download Pdf Manuals
Related Search