Kawasaki 840442 User's Manual
Contents
1. OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE Limitation Of Liability IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECTLY OR INDIRECTLY ANY BREACH OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRESENTATIVE S AND PURCHASER ANY WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOLD HEREUNDER EVEN IF ALLTRADE AND OR ITS 23 REPRESENTATIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES IN NO EVENT WHETHER AS A RESULT OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE Limitations on Warranty Disclaimers Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequ2. Pull the hole in the shank of the blade off the pin in the saw bar Tighten the blade clamp screw back into place Remove allen wrench Replace the battery pack 14 OPERATING THE RECIPROCATING SAW WARNING Never tape the trigger switch down to provide continuous high speed The tool may fail under such conditions causing fire or personal injury The lock off button helps prevent accidental starting This button can be pressed from either side VARIABLE SPEED TRIGGER SWITCH TRIGGER SWITCH Ve Z LOCK ON BUTTON THIS TOOL IS CONTROLLED BY A TRIGGER SWITCH The speed of the Cordless Reciprocating Saw depends on the amount of pressure applied on the trigger The further the trigger is pressed the faster the tool will go Press the lock off button then pull the ON OFF trigger to turn the Cordless Reciprocating Saw ON To turn the Cordless Reciprocating Saw OFF release the trigger switch GENERAL CUTTING A WARNING Always hold the saw in front of you and away from your body Keep your hands and feet well away from the work piece Never feed the blade into the work piece until the blade is at full speed If the blade is not at full speed the saw may kick back causing serious personal injury Use proper blade for the particular cutting application 15 e Put on eye protection Clear the saw of any foreign material Make s
3. may cause sparks burns or a fire Maintain tools with care Keep cutting tools sharp and clean Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the tool s operation If damaged have the tool serviced before using accidents are caused by poorly maintained tools Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may create a risk of injury when used on another tool Tool service must be performed only by qualified repair personnel Service or maintenance by unqualified personnel may result in a risk of injury When servicing a tool use only identical replacement parts Follow instruc tions in the Maintenance section of this manual Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury SPECIFIC SAFETY RULES AND OR SYMBOLS A CAUTION Hold tool by insulated gripping surfaces when per forming an operation where the cutting tool may contact hidden wiring Contact with a live wire will also make exposed metal parts of the tool live and shock the operator SAFETY RULES FOR CORDLESS RECIPROCATING SAW 4 CAUTION Always wear safety goggles or eye protection when using this tool Use a dust mask or respirator for application
4. metal place a piece of plywood on either side to control vibration and prevent tearing 17 MAINTENANCE AND CLEANING WARNING Always remove the battery pack before attempting cleaning or maintenance This Cordless Reciprocating Saw is lubricated before it leaves the factory This lubrication should last for the life of the tool No further lubrication is required Use only mild soap and a damp cloth to clean the tool Never let any liquid get inside the casing Never immerse any part of the tool in a liquid Always keep the ventilation openings clear Always clean the battery pack using only a dry cloth Do not use liquids Always unplug the charger before cleaning it Regularly clean the ventilation slots in your tool and charger using only a soft brush or dry cloth Inspect all mounting screws regularly Tighten any loose screws Failure to keep the mounting screws tight could result in serious injuries Never open the Cordless Reciprocating Saw case battery pack or charger Do not attempt to repair the Cordless Reciprocating Saw battery pack or charger yourself Opening any of these parts will void your warranty Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool Always attach grounded 3 prong extension cords to grounded 3 hole outlets If you must use an extension cord be sure that the gaug
5. with sharp cutting edges are less likely to bind and are easier to control When restarting a saw in the workpiece check that teeth are not engaged in the material Keep the handle of the Cordless Reciprocating Saw dry clean and free from oil and grease Be extra careful when cutting in high or hard to reach locations Be on the lookout for hidden wires and falling debris Maintain labels and nameplates on the Cordless Reciprocating Saw These carry important information If unreadable or missing contact Alltrade for a replacement SYMBOLS IMPORTANT Some of the following symbols may be used on your tool Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the tool better and safer SYMBOL NAME EXPLANATION Volts Voltage Potential A Amperes Current Hz Hertz Frequency Cycles per Second W Watt Power Kg Kilograms Weight No Alternating Current Type of Current z Direct Current Type of Current Alternating or Direct Current Type of Current Earthing Terminal Grounding Terminal 5 Class II Construction Denotes Double Insulation min Minutes Time S Seconds Time Diameter Size of Drill Bits Grinding Wheels etc n No load speed No load Rotational Speed min Revolutions per Minute Revolutions Surface Speed Strokes etc per Minute 1238 2 Ring Selector Settings Speed Torque or Position Settings FUNCTIONAL DESCRIPTION WARNING Use only
6. ENT GIVE US A CALL OR EMAIL US AT INFO ALLTRADETOOLS COM YOUR FEEDBACK IS VITAL TO US TABLE OF CONTENTS CONGRATULATIONS 2 INTENDED USE 2 SECTION ONE GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS 2 RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS 2 3 IMPORTANT SAFEGUARDS 3 WORK AREA eo 4 ELECTRICAL SAFETY Sica wens Meee pens Rena Me 4 PERSONAL SAFETY es 5 TOOL USE AND nde See eae ee 5 6 SERVICE care ods ev lca putes vena ss 6 SECTION TWO SPECIFIC SAFETY RULES AND OR SYMBOLS 6 SAFETY RULES FOR CORDLESS RECIPROCATING SAW 6 7 SYMBOLS oe yee ay pe Wann es 8 SECTION THREE FUNCTIONAL DESCRIPTION 9 BATTERY meets 9 13 REMOVING ATTACHING BATTERY 11 CHARGER 690072 ADAPTER 690074 11 CHARGING BATTERY PACK USING CHARGER 690072 ADAPTER 690074 12 ONE HOUR CHARGER 690507 12 13 CHARGING BATTERY PACK USING ONE HOUR CHARGER 690507 13 ASSEMBLY tad iy oe 13 14 ATTACHING REMOVING BLADE 14 OPERATING THE RECIP
7. ER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS PRODUCT ALL EXPRESS AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE PURCHASER INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY
8. FOR CUSTOMER SERVICE POUR LE SERVICE APRES VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1 800 590 3723 Printed in China WTERTE c Conforms to Std UL745 3 Listed 3076022 UL745 4 11 Kawasaki Kawasaki Motors Corp U S A OFFICIAL LICENSED PRODUCT 87 1904 60957 KAWASAKI IS A TRADEMARK LICENSED BY KAWASAKI MOTORS CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO COPYRIGHT 2007 ALLTRADE TOOLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 690088_19 2V Black Cordless Reciprocating Saw_Rev 7 14 07 COMPONENT Kawasaki 19 2V BATTERY OPERATED RECIPROCATING SAW INSTRUCTION MANUAL BATTERIES AND CHARGERS SOLD SEPARATELY THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE OF THIS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS INSTRUCTIONS AND PRODUCT LABELS FAILURE TO DO 50 COULD RESULT IN SERIOUS PERSONAL INJURY AND OR PROPERTY DAMAGE IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT DO NOT RETURN THIS PRODUCT TO THE STORE PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1 800 590 3723 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL No DATE PURCHASED AND STORE LOCATION AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE IF YOU WOULD LIKE TO MAKE A SUGGESTION OR COMM
9. Kawasaki 19 21 Battery Pack 691034 or CONTROLS AND COMPONENTS 691240 with the One Hour Charger 690507 1 Saw Shoe 2 Trigger Switch 3 Lock Off Button 4 Rubber Grip 5 Allen Wrench NOTE The battery is not fully charged Charger 690072 Adapter 690074 Before first use the battery pack requires 8 10 hours charge time to be fully charged Subsequent recharging needs 3 5 hours for the battery to be fully charged ACCESSORIES 6 Wood Cutting Blade 7 Metal Cutting Blade One Hour Charger 690507 Before first use the battery pack requires 3 5 hours charge time to be fully charged Subsequent recharging needs 1 hour for the battery to be fully charged BATTERY Always switch to a fresh battery when tool performance begins to diminish Severe heat is most destructive to a battery the more heat generated the faster the battery loses power A battery that gets too hot can have a shortened life Never over discharge a battery by using the tool even after tool performance has decreased Do not attempt to discharge a tool s battery by continuing to pull on the tool trigger When tool performance begins to diminish stop the tool and recharge the battery for optimal performance Before using battery pack please read carefully all instruc tions and cautionary markings on battery pack battery charger and product using battery Do not incinerate the battery pack even if it is severely damaged or
10. RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating maintaining and cleaning power tools Always use common sense and pay particular attention to all the DANGER WARNING CAUTION and NOTE statements of this manual A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates an imminently hazardous situation which if not avoided will result in death serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE NOTE provides additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood IMPORTANT SAFEGUARDS DANGER People with electronic devices such as pacemakers should consult their physician s before using this product Operation of electrical equipment in close proximity to a heart pacemaker could cause inte
11. ROCATING SAW 15 17 VARIABLE SPEED TRIGGER 5 15 GENERAL CUTTING 15 16 PLUNGE CUTTING 0 cece eee 16 17 METAL CUTTING ieee fecha eke het bene ghee 17 SECTION FOUR MAINTENANCE AND CLEANING 18 ACCESSORIES 18 19 SPECIFICATIONS riiai 19 PROTECTING THE ENVIRONMENT 19 OTHER CONSUMER DO IT YOURSELF DIY TOOLS 20 SECTION FIVE 2 YEAR LIMITED 21 24 CONGRATULATIONS Thanks for choosing this product At Alltrade our aim is to provide you with quality products at an affordable price and we want you to be totally satisfied with your product and our Customer Service If any help and advice is needed please contact us at 1 800 590 3723 Properly cared for this tool will give you many years of satisfaction INTENDED USE This tool is intended for consumer use only Your charger and or adapter has been designed for charging batteries of the type approved and supplied with this tool GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
12. al wear abnormal conditions misapplication misuse abuse accidents operation at other than recommended pressures or temperatures improper storage or freight damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow recommended operating and maintenance procedures also voids warranty This limited warranty does not apply to accessory items such as drill bits screwdriving bits circular saw blades jigsaw blades grinding wheels sanding sheets and other related items DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUSE NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY Alltrade will not be liable for the following labor charges loss or damage resulting from improper operation maintenance or repairs made by other persons pre delivery services such as assembly oil or lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Alltrade Repair Parts will void warranty 22 Warranty Disclaimers EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY PROVIDED ABOVE ALL OTH
13. ase the battery pack j gt en Po Pull battery pack free of Cordless Reciprocating Saw ATTACH BATTERY PACK 1 Align the raised portion of the battery pack with the groove in the battery compartment of the Cordless Reciprocating Saw 2 Press the battery pack into place Make sure the latches are securely fastened Do not use the Cordless Reciprocating Saw if the battery pack is not seated properly CHARGER 690072 ADAPTER 690074 4 WARNING Before using battery charger please read carefully all instructions and cautionary markings on battery charger battery pack and product using battery NOTE The charger will not automatically turn OFF when the battery pack is fully charged The charging indicator light will remain ON until the charger is disconnected from the electrical outlet Use only the charger which accompanied your product or direct replacement as listed in this manual Do not substitute any other charger Use only Alltrade approved chargers with your product Do not disassemble charger Do not use charger if it has been damaged left outdoors in the rain snow wet or damp environments or immersed in liquid The battery pack and charger heat during charging Place the charger on a flat non flammable surface away from flammable materials with at least four inches of clearance to allow proper air circulation around the charger and battery pack When the battery pack requires rec
14. battery pack the red ON button does not light up press the SET button on the charger When the battery is charging the red light is ON After approximately one hour of charging the red indicator light should go OFF and the green light should come ON The green light indicates that the battery is fully charged When fully charged reattach battery pack onto Cordless Reciprocating Saw making certain latches fasten securely Cordless Reciprocating Saw will not oper ate properly if the battery pack is not seated properly ASSEMBLY WARNING Be aware that this tool is always in an operating condition because it does not have to be plugged into an electrical outlet Always turn the switch OFF and remove the battery pack before changing blades 13 ATTACHING REMOVING BLADE WARNING Failure to remove the battery pack from the saw before removing the blade could result in accidental starting and serious personal injury BLADE CLAMP Remove the battery pack Use the allen wrench to loosen the blade clamp screw on the side of the saw by turning it counter clockwise Do not remove the screw entirely TO ATTACH BLADE Press the hole in the shank of the blade onto the pin in the saw bar Make sure that the teeth of the blade are facing downward Tighten the blade clamp screw back into place Remove allen wrench Replace the battery pack TO REMOVE BLADE
15. ch Keep proper footing and balance at all times Proper foot ing and balance enable better control of the tool in unexpected situations Use safety equipment Always wear eye protection Dust mask non skid safe ty shoes hard hat or hearing protection must be used for appropriate conditions TOOL USE AND CARE A CAUTION Use clamps or other practical ways to secure and support the workpiece to a stable platform Holding the work by hand or against your body is unstable and may lead to loss of control Do not force tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for which it is designed Do not use the tool if the power switch does not turn it ON or OFF A tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect battery pack from tool or place the switch in the locked or OFF posi tion before making any adjustments changing accessories or storing the tool Such preventative safety measures reduce the risk of starting the tool accidentally Store idle tools out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users 4 CAUTION When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery termi nals together
16. e is large enough to carry the amount of current necessary for your power tool If not your tool may experi ence a loss of power excessive voltage drop or overheating The smaller the gauge number the heavier the cord see table on the next page 18 RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS TOOL CURRENT RATING CONDUCTOR SIZE IN A W G AMPERE 10FT 25FT SOFT 100FT 3 6 18 18 18 18 6 8 18 18 18 16 8 10 18 18 18 14 10 12 16 16 14 14 12 16 14 12 12 16 20 12 12 12 SPECIFICATIONS Voltage 19 2V Length of Stroke 22mm 7 8 No Load Speed RPM 0 2600 min Charger Input 120V 60Hz Battery Type Ni Cad PROTECTING THE ENVIRONMENT BATTERIES Alltrade batteries can be recharged many times At the end of their useful life recy Cle batteries with due care for our environment Ni Cad and Ni MH batteries are recyclable Take them to your local recycling center or call 1 800 822 8837 Collected batteries will be recycled or disposed of properly 19 OTHER CONSUMER DO IT YOURSELF DIY TOOLS Alltrade offers a full range of Kawasaki tools that make DIY jobs easy If you would like further information on the following products please contact Alltrade Customer Service Department at 1 800 590 3723 Cordless Drills Screwdrivers Impact Wrenches Sanders Jigsaws Circular Saws Angle Grinders Reciprocating Saws Routers Rotary Tools Corded and Cordless Multi Purpose Tools Wide Rang
17. e of Accessories and more 20 2 YEAR LIMITED HOME USE WARRANTY Express and Exclusive Limited Home Use Warranty to Original Retail Buyer Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying KAWASAKI portable power tool and no one else all parts of the product except those parts referred to below which are specifically excluded from such warranty see Exclusions to be free from defects in materials and workmanship for a period of two years from original date of purchase SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS This Kawasaki portable power tool is offered as a home use tool and carries a HOME USE WARRANTY This tool is made for home use in the execution of projects and repairs in and around the home Use of the tool for COMMERCIAL PURPOSES OR ON A JOBSITE is not covered under this warranty The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession custody or control of the product whichever occurred first This warranty shall be null and void if the product or any component thereof is modified altered or used for any commercial purpose or on a jobsite This warranty does not apply to any other product and or component thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Allt
18. ential damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If your product is not covered by this warranty please call our Customer Service Department toll free at 1 800 590 3723 for general repair information and charges 24
19. harging a 3 5 hour charge allows the tool to operate at full power A charging indicator light on the charger will illuminate to show that charging is taking place 11 CHARGING BATTERY PACK USING CHARGER 690072 ADAPTER 690074 CHARGE BATTERY PACK BATTERY PACK Make sure the trigger on the Cordless Reciprocating Saw is in the OFF posi 120V AC tion and remove the battery ADAPTER pack from the Cordless Reciprocating Saw 4 2 Insert the battery pack into the charger Be sure that the battery pack is fully seated in the charger Do not force 3 Plug the charger into the a nearest 120 volt electrical outlet The indicator light will come ON IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES When using your Cordless Reciprocating Saw continuously the batteries in your battery pack will become hot You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge When the battery pack becomes discharged and is hot the red light on the charger will flash When the bat tery pack cools down the red light will glow continuously NOTE This will occur when continuous use of your Cordless Reciprocating Saw causes the battery pack to become hot It does not occur under normal circumstances ONE HOUR CHARGER 690507 WARNING Before using battery charger please read carefully all instructions and cautionary markings on battery charger batter
20. he tool Keep the cord away from heat oil sharp edges or moving parts Replace damaged cords immediately Damaged cords may create a fire A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery A charger that may be suitable for one type of battery may create a risk of fire when used with another battery Use battery operated tool only with specifically designated battery pack Use of any other batteries may create risk of fire PERSONAL SAFETY A WARNING Stay alert watch what you are doing and use common sense when operat ing a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Avoid accidental starting Be sure switch is in the locked or OFF position before inserting battery pack Carrying power tools with your finger on the switch or inserting battery pack into a tool with the power switch ON invites accidents Remove adjusting keys or wrenches before turning the tool ON A wrench or a key that is left attached to a rotating part of the tool may result in person al injury Do not overrea
21. is completely worn out The battery pack can Charge battery pack at ambient temperatures between 50 104 explode Store tool and battery pack in locations where temperatures will not exceed Do not carry battery packs in aprons pockets or tool boxes product kit 120 F This is important to prevent serious damage to the battery cells boxes drawers etc with loose metal objects Battery pack terminals could be The battery pack should always be recharged when the Cordless Reciprocating short circuited causing damage to the battery pack severe burns or fire Saw begins to run slowly The battery pack is Nickel Cadmium Ni Cad and is considered to be a toxic When battery pack is not in use keep it away from other metal objects such as material by the Environmental Protection Agency Before disposing of dam paper clips coins keys nails screws or other small metal objects that can make aged or worn out Ni Cad battery packs check with your State Environmental a connection from one terminal to another Shorting the battery terminals togeth Protection Agency to find out about special restrictions on the disposal of these er may cause sparks burns or fire battery packs take them to your local recycling center for proper disposal or call 1 800 822 8837 REMOVING ATTACHING BATTERY PACK REMOVE BATTERY PACK 1 Press both release a buttons on either gt S side of the Cordless wee Reciprocating Saw to z rele
22. rade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF Warranty Performance By purchasing the product purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and or part is promptly returned to Alltrade s facility postage pre paid and insured address ALLTRADE Warranty Claims amp Repair 1431 Via Plata Long Beach CA 90810 Attn Customer Service 1 800 590 3723 within the applicable warranty period with a written request by purchaser that Alltrade repair and or replace the nonconforming item and or part We recommend that you keep the original product packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit damage When sending your product include your name address phone number dated proof of purchase or copy and a statement about the nature of problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insured to Alltrade s facility see above address will be inspected and at Alltrade s option repaired and or replaced free of charge if found to be defective and subject to wa
23. rference or failure of the pacemaker WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paints Crystalline silica from bricks and cement and other masonry products and arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles WARNING Handling the power cord on corded products may expose you to lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling A WARNING Keep your work area clean and well lit Cluttered work benches and dark work areas may Cause accidents or injury Do not operate power tools in explosive areas such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep bystanders children and visitors away while operating a power tool Distractions can cause you to lose control ELECTRICAL SAFETY A WARNING Do not abuse the cord Never use the cord to carry t
24. rranty Alltrade retains the sole discretion to determine whether any item or part is nonconforming and if so whether the 21 item and or part will be repaired and or replaced If the unit is repaired new or reconditioned replacement parts may be used If Alltrade chooses to replace the product it may replace it with a new or reconditioned one of the same or comparable design The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period Typically a defective product that is returned within the first 30 days after the purchase date will be replaced for items returned after the first 30 days and within the warranty period covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option During the warranty period Alltrade will be responsi ble for the return shipping charges Alltrade s repair and or replacement of any non conforming item and or part thereof shall constitute fulfillment of all obligations to the purchaser Alltrade shall not be responsible or liable for any expense including freight charges or repairs made outside Alltrade s facility unless expressly agreed to by Alltrade in writing Under no circumstances shall Alltrade bear any responsibility for loss of the unit loss of time or rental inconvenience commercial loss or consequential damages Exclusions This warranty does not cover parts damaged due to norm
25. s which generate dust Secure the material being worked on Never hold it in your hand or across your legs Unstable support can cause loss of control and injury When using the Cordless Reciprocating Saw always maintain a firm grip on the tool with both hands Never put your hands or feet in the cutting area Do not grasp the tool or place your hands too close to the blade Keep your hands well away from the blade Never reach underneath the tool while the blade is in motion Do not use your legs or feet to stabilize the work piece Position yourself to avoid being caught between the tool or side handle and walls or posts Should the blade become bound or jammed in the work it could result in loss of control and injury Do not run the Cordless Reciprocating Saw while carrying it at your side A mov ing blade could cause serious personal injury Disconnect battery pack from tool and place the switch in the locked or OFF position before making any assembly adjustments changing acces sories performing any inspection maintenance or cleaning procedures Such preventive safety measures reduce the risk of starting the tool accidental ly which could cause serious personal injury Do not use the Cordless Reciprocating Saw if it has been damaged left out doors in the rain snow wet or damp environments or immersed in liquid Do not use dull or damaged blades Keep cutting tools sharp and clean Properly maintained cutting tools
26. ure the work piece is held securely in place Hold smaller pieces in a vise or attach to the workbench with clamps Mark out the line to be cut so it is easily visible Pull the trigger to start the saw Set the shoe against the work piece When the blade reaches full speed slowly feed the blade into the work piece PLUNGE CUTTING WARNING Never feed the blade into the work piece until the blade is at full speed If the blade is not at full speed the saw may kick back causing serious personal injury Mark out the line to be cut so it is easily visible Start inside the area to be cut out Depress the lock on button and press the trigger to start the saw 16 Set the shoe against the work piece When the blade reaches full speed slowly feed the blade into the work piece METAL CUTTING 4 WARNING Never use gasoline or any flammable liquid as a lubricant Sparking from the motor may cause it to ignite into flames When cutting metals other then copper brass or aluminum always use a lubricant such as cutting oil to keep the blade cool This will prolong the life of the blade as well as speeding up the cutting process Make sure the work piece is held securely place Hold smaller pieces such as pipe or conduit in a vise or attach to the workbench with clamps To eliminate vibration always cut close to the clamping point When cutting thin sheets of
27. y pack and product using battery Use only the charger which accompanied your product or direct replacement as listed in this manual Do not substitute any other charger Use only Alltrade approved chargers with your product Do not disassemble charger Do not use charger if it has been damaged left outdoors in the rain snow wet or damp environments or immersed in liquid 12 The battery pack and charger heat during charging Place the charger on a flat non flammable surface away from flammable materials with at least four inches of clearance to allow proper air circulation around the charger and battery pack When the battery pack requires recharging a 1 hour charge allows the tool to operate at full power A charging indicator light on the charger will illuminate to show that charging is taking place CHARGE BATTERY PACK 1 Po oo a oi Make sure the trigger on the CHARGING BATTERY PACK USING ONE HOUR CHARGER 690507 BATTERY PACK Plug the charger into the nearest 120 volt electrical outlet The step of the battery has positive and negative terminal markings on it Align the markings with the identical markings on the top of the charger base Insert the battery pack into base Pack will not insert properly if reversed Cordless Reciprocating Saw is in the OFF position and remove the battery pack from the Cordless Reciprocating Saw BATTERY CHARGER If when first inserting the
Download Pdf Manuals
Related Search