Home

Kawasaki 840138-1HR User's Manual

1. COMPONENT MODEL NUMBER BATTERY PACK 690549 CHARGER 690543 A WARNING Before using battery pack please read carefully all instructions and cautionary markings on battery pack battery charger and product using battery Do not incinerate the battery pack even if it is severely dam aged or is completely worn out The battery pack can explode Do not carry battery packs in aprons pockets or tool boxes product kit boxes drawers etc with loose metal objects Battery pack terminals could be short circuited causing damage to the battery pack severe burns or fire The battery pack is Nickel Cadmium Ni Cad and is considered to be a toxic material by the Environmental Protection Agency Before disposing of dam aged or worn out Ni Cad battery packs check with your State Environmental Protection Agency to find out about special restrictions on the disposal of these battery packs take them to your local recycling center for proper disposal or call 1 800 822 8837 NOTE The battery is not fully charged Before first use the battery pack requires 3 5 hours charge time to be fully charged Subsequent recharging needs 1 hour for the battery to be fully charged Always switch to a fresh battery when tool performance begins to diminish Severe heat is most destructive to a battery the more heat generated the faster the battery loses power A battery that gets too hot can have a shortened life Never over discharge a battery by using
2. before using this product Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paints Crystalline silica from bricks and cement and other masonry products and arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles WARNING Handling the power cord on corded products may expose you to lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE BATTERY TOOL USE AND CARE Ensure the switch is in the off position before inserting battery pack Inserting the battery pack into power tools that have the switch on invites accidents Recharge only with the charger specified by the manufacturer A charger that is suitable for one type of battery pack may create a risk of fire when used wit
3. of the product except those parts referred to below which are specifically exclud ed from such warranty see Exclusions to be free from defects in materials and workmanship for a period of three years from original date of purchase except that such warranty with regard to the battery shall be for a period of two years from original date of purchase unless the tool is used for commercial or rental purposes SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE The above warranty for this Kawasaki power tool including the battery shall be effective for only 90 days from the original date of purchase if this tool is used for any COMMERCIAL OR RENTAL PURPOSE The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession custody or control of the product whichever occurred first This warranty shall be null and void if the product or any component thereof is modified or altered This warranty does not apply to any 13 other product and or component thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Alltrade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF Warranty Performance By purchasing the product purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this wa
4. ALLTRADETOOLS COM YOUR FEEDBACK IS VITAL TO US CONGRATULATIONS Thanks for choosing this product At Alltrade our aim is to provide you with quality products at an affordable price and we want you to be totally satisfied with your product and our Customer Service If any help and advice is needed please contact us at 1 800 590 3723 Properly cared for this tool will give you many years of satisfaction INTENDED USE This tool is intended for consumer use only Your charger and or adapter has been designed for charging batteries of the type approved and supplied with this tool RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating maintaining and cleaning power tools Always use common sense and pay particular attention to all the DANGER WARNING CAUTION and NOTE statements of this manual A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or m
5. EVEN IF ALLTRADE AND OR ITS 21 REPRESENTATIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES IN NO EVENT WHETHER AS A RESULT OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE Limitations on Warranty Disclaimers Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequential damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If your product is not covered by this warranty please call our Customer Service Department toll free at 1 800 590 3723 for general repair information and charges 22 F0R CUSTOMER SERVICE P0UR LE SERVICE APR S VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1 800 590 3723 Printed in China Kawasaki Kawasaki Motors Corp U S A OFFICIAL LICENSED PRODUCT 87 1904 60957 KAWASAKI IS A TRADEMARK LICENSED BY KAWASAKI MOTORS CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO COPYRIGHT 2006 ALLTRADE TO
6. fully charged Always switch to a fresh battery when tool performance begins to diminish Severe heat is most destructive to a battery the more heat generated the faster the battery loses power A battery that gets too hot can have a shortened life Never over discharge a battery by using the tool even after tool performance has decreased Do not attempt to discharge a tool s battery by continuing to pull on the tool trigger When tool performance begins to diminish stop the tool and recharge the battery for optimal performance Charge battery pack at ambient temperatures between 50 F 104 F Store tool and battery pack in locations where temperatures will not exceed 120 F This is important to prevent serious damage to the battery cells The battery pack should always be recharged when the Cordless Drill begins to run slowly When battery pack is not in use keep it away from other metal objects such as paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause sparks burns or fire SYMBOLS IMPORTANT Some of the following symbols may be used on your tool Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the tool better and safer SYMBOL NAME EXPLANATION V Volts Voltage Potential A Amperes Current Hz Hertz Frequency Cycles per Seco
7. or missing contact Alltrade for a replacement Battery pack must be recharged only with the specified charger for the battery A charger that may be suitable for one type of battery may create a risk of fire when used with another battery Do not use in a damp or wet environment Store out of reach of children and other untrained persons 4 SYMBOLS IMPORTANT Some of the following symbols may be used on your tool Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the tool better and safer SYMBOL NAME EXPLANATION V Volts Voltage Potential A Amperes Current Hz Hertz Frequency Cycles per Second W Watt Power Kg Kilograms Weight N Alternating Current Type of Current Direct Current Type of Current Alternating or Direct Current Type of Current Earthing Terminal Grounding Terminal El Class II Construction Denotes Double Insulation min Minutes Time S Seconds Time j Diameter Size of Drill Bits Grinding Wheels etc H No load speed No load Rotational Speed min Revolutions per Minute Revolutions Surface Speed Strokes etc per Minute 1 29 Ring Selector Settings Speed Torque or Position Settings FUNCTIONAL DESCRIPTION SS Y JS CONTROLS AND COMPONENTS 1 Battery Pack 2 Release Buttons on Each Side 3 Charger 4 LED Charging Indicators 5 ON OFF Switch 6 Reflector Rim ACCESSORIES 7 Replacement Light bulb inside unit
8. parts and any other condition that may affect the tool s operation If damaged have the tool serviced before using Many accidents are caused by poorly maintained tools Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may create a risk of injury when used on another tool SERVICE Tool service must be performed only by qualified repair personnel Service or maintenance by unqualified personnel may result in a risk of injury When servicing a tool use only identical replacement parts Follow instructions in the Maintenance section of this manual Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury SPECIFIC SAFETY RULES AND OR SYMBOLS 4 CAUTION Hold tool by insulated gripping surfaces when perform ing an operation where the cutting tool may contact hidden wiring Contact with a live wire will also make exposed metal parts of the tool live and shock the operator SAFETY RULES FOR CORDLESS DRILL DRIVERS A CAUTION Always wear safety goggles or eye protection when using this tool Use a dust mask or respirator for applications which generate dust Do not grasp the tool or place your hands too close to the spinning chuck or drill bit Your hand may be lacerated or may cause injury Secure the material being worked on Never hold it in your hand or across your legs Unstable suppo
9. when drilling large diameter holes in wood Use HSS drill bits when drilling in metal Use masonry bits when drilling in soft masonry Use a lubricant when drilling metals other than cast iron aluminum copper and brass When drilling start the hole slowly allowing the bit to drill deep enough to prevent slipping at higher speeds 15 Never try to start a stalled Drill by clicking the trigger switch ON and OFF This may damage your tool To reduce jamming always keep the Drill running when pulling the bit out of a finished hole SCREWDRIVING Always use the correct type and size of screwdriver bit f screws are difficult to tighten try applying a small amount of washing liquid or soap as a lubricant Always hold the tool and screwdriver bit in a straight line with the screw MAINTENANCE AND CLEANING 4 WARNING Always remove the battery pack before attempting cleaning or maintenance NOTE This Cordless Drill is lubricated before it leaves the factory This lubrication should last for the life of the tool No further lubrication is required Use only mild soap and a damp cloth to clean the tool Never let any liquid get inside the casing Never immerse any part of the tool in a liquid Always keep the ventilation openings clear Always clean the battery pack using only a dry cloth Do not use liquids Always unplug the charger before cleaning it Regularly clean the ventilation
10. ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE Limitation Of Liability IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECTLY OR INDIRECTLY ANY BREACH OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRESENTATIVE S AND PURCHASER ANY WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOLD HEREUNDER EVEN IF ALLTRADE AND OR ITS REPRESENTATIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES IN NO EVENT WHETHER AS A RESULT OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE Limitations on Warranty Disclaimers Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequential damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If your product is not covered by this warranty please call our Cust
11. AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS PRODUCT ALL EXPRESS AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE PURCHASER INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESE
12. CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS PRODUCT ALL EXPRESS AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE PURCHASER INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE Limitation Of Liability IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECTLY OR INDIRECTLY ANY BREACH OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRESENTATIVE S AND PURCHASER ANY WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOLD HEREUNDER
13. D OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE ABOVE 15 WARRANTY IS MADE WITH REGARD TO THIS PRODUCT ALL EXPRESS AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE PURCHASER INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF
14. ELS 4 WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating maintaining and cleaning power tools Always use common sense and pay particular attention to all the DANGER WARNING CAUTION and NOTE statements of this manual A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury 4 DANGER WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage CAUTION NOTE provides additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood NOTE IMPORTANT SAFEGUARDS A DANGER People with electronic devices such as pacemakers should consult their physician s
15. ER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY Alltrade will not be liable for the following labor charges loss or damage resulting from improper operation maintenance or repairs made by other persons pre delivery services such as assembly oil or lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Alltrade Repair Parts will void warranty 20 Warranty Disclaimers EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY PROVIDED ABOVE ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MER
16. F0R CUSTOMER SERVICE POUR LE SERVICE APRES VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1 800 590 3723 Printed in China Kawasaki Kawasaki Motors Corp U S A OFFICIAL LICENSED PRODUCT 87 1904 60957 KAWASAKI IS A TRADEMARK LICENSED BY KAWASAKI MOTORS CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO COPYRIGHT 2006 ALLTRADE TOOLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 840138 19 2V Green Cordless Drill Rev 8 26 06 COMPONENT K ki 840138 1HR awasakIl 19 2V 2 SPEED BATTERY OPERATED DRILL INSTRUCTION MANUAL THS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE OF THS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS INSTRUCTIONS AND PRODUCT LABELS FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL IN URY AND OR PROPERTY DAMACE IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WTH YOUR ALLTRADE PRODUCT DO NOT RETURN THS PRODUCT TO THE STORE PLEASE CALL CUR CUSTOMER SERMCE DEPARTMENT AT 1 800 590 3723 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL No DATE PURCHASED AND STORE LOCATION AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE IF YOU WOULD LIKE TO MAKE A SUGGESTION OR COMMENT GIVE US A CALL OR EMAIL US AT INFO ALLTRADETOOLS COM YOUR FEEDBACK IS VITAL TO US TABLE OF CONTENTS CONGRATULA
17. LLING WOOD caen hee ainai 15 HINTS FOR OPTIMUM USE 15 16 SECTION FOUR MAINTENANCE AND CLEANING 00 ccc cece I 16 ACCESSORIES sse dass ive et aqa auqa 17 SPECIFICATIONS iv urbc o E eec eee e Ped Rs 17 PROTECTING THE ENVIRONMENT 18 OTHER CONSUMER DO IT YOURSELF DIY TOOLS 18 SECTION FIVE 3 YEAR LIMITED WARRANTY II 19 22 CONGRATULATIONS Thanks for choosing this product At Alltrade our aim is to provide you with quality products at an affordable price and we want you to be totally satisfied with your product and our Customer Service If any help and advice is needed please contact us at 1 800 590 3723 Properly cared for this tool will give you many years of satisfaction INTENDED USE This tool is intended for consumer use only Your charger and or adapter has been designed for charging batteries of the type approved and supplied with this tool GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS 4 WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating maintaining and cleaning power tools Always use common sens
18. NTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE Limitation Of Liability IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECTLY OR INDIRECTLY ANY BREACH OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRESENTATIVE S AND PURCHASER ANY WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOLD HEREUNDER EVEN IF ALLTRADE AND OR ITS REPRESENTATIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES IN NO EVENT WHETHER AS A RESULT OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE Limitations on Warranty Disclaimers Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequential damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also ha
19. OLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 840138 19 2V Green Cordless Worklight_Rev 7 19 06 COMPONENT 840138 1HR Kawasaki 19 2V BATTERY OPERATED WORKLIGHT INSTRUCTION MANUAL THS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE OF THS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS INSTRUCTIONS AND PRODUCT LABELS FAILURE TODO SOCOULD RESULT IN SERIOUS PERSONAL IN URY AND OR PROPERTY DAMACE IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WTH YOUR ALLTRADE PRODUCT DO NOT RETURN THS PRODUCT TO THE STORE PLEASE CALL CUR CUSTOMER SERVICE DEPARTMENT AT 1 800 590 3723 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL NO DATE PURCHASED AND STORE LOCATION AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE IF YOU WOULD LIKE TO MAKE A SUGGESTION OR COMMENT GVE US A CALL OR EMAIL US AT INFO ALLTRADETOOLS COM YOUR FEEDBACK IS VITAL TO US TABLE OF CONTENTS CONGRATULATIONS 0 eee ee 2 INTENDED USE iere i RERO Maa oe Ri as ayu 2 SECTION ONE RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS 2 3 IMPORTANT SAFEGUARDS 3 BATTERY TOOL USE AND CARE 4 SERVICE nen uamea n9 1a Ment ait an ata mip LP Ebert 4 SECTION TWO SAFETY RULES FOR WORKLIGHT 4 SYMBOLS iier rax rera eee Ee wanwa P RC Ra E ceo eon 5 SEC
20. TENSION CORDS 120 VOLT AC 60 HZ TOOLS TOOL CURRENT RATING CONDUCTOR SIZE IN A W G AMPERE 10FT 25FT 50FT 100FT 3 6 18 18 18 18 6 8 18 18 18 16 8 10 18 18 18 14 10 12 16 16 14 14 12 16 14 12 12 16 20 12 12 12 SPECIFICATIONS SPECIFICATIONS Voltage 19 2V Light Bulb Type Krypton 18V 0 3A Charger Input 120V NJ 60Hz Charging Time Approx 1 Hour Battery Type Ni Cad PROTECTING THE ENVIRONMENT BATTERIES Alltrade batteries can be recharged many times At the end of their useful life recy cle batteries with due care for our environment Ni Cad and Ni MH batteries are recyclable Take them to your local recycling center or call 1 800 822 8837 Collected batteries will be recycled or disposed of properly OTHER CONSUMER DO IT YOURSELF DIY TOOLS Alltrade offers a full range of Kawasaki tools that make DIY jobs easy If you would like further information on the following products please contact Alltrade Customer Service Department at 1 800 590 3723 Cordless Drills Screwdrivers Reciprocating Saws Impact Wrenches Routers Sanders Rotary Tools Jigsaws Corded and Cordless Multi Purpose Tools Circular Saws Wide Range of Accessories and more Angle Grinders 3 YEAR LIMITED WARRANTY Express and Exclusive Limited Warranty to Original Retail Buyer Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying KAWASAKI power tool and no one else all parts
21. TION THREE FUNCTIONAL DESCRIPTION 1 6 BATTERY eodd bee d dened adt oa aa a deed alienata 7 9 REMOVING ATTACHING BATTERY PACK 7 CHARGER sog saa yaaa umu Re ERROR aqha ease a pea Ba 8 CHARGING BATTERY PACK 9 OPERATING THE WORKLIGHT a 10 11 OPERATING THE ON OFF SWITCH 10 ADJUSTING THE WORKLIGHT BEAM 10 REPLACING THE LIGHT BULB 10 11 SECTION FOUR MAINTENANCE AND CLEANING 11 12 ACCESSORIES suarena ek e x e a iia Ens 12 SPECIFICATIONS z ite t Ex cbe oes cb eed 12 PROTECTING THE ENVIRONMENT 13 OTHER CONSUMER DO IT YOURSELF DIY TOOLS 13 SECTION FIVE 3 YEAR LIMITED WARRANTY cece eee 13 16 CONGRATULATIONS Thanks for choosing this product At Alltrade our aim is to provide you with quality products at an affordable price and we want you to be totally satisfied with your product and our Customer Service If any help and advice is needed please contact us at 1 800 590 3723 Properly cared for this tool will give you many years of satisfaction INTENDED USE This tool is intended for consumer use only Your charger and or adapter has been designed for charging batteries of the type approved and supplied with this tool RECOGNIZE SAFETY SYMBOLS WORDS AND LAB
22. TIONS 0 eee 2 INTENDED USE i ici ccd has a ed ORE REC Gc f n au 2 SECTION ONE GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS 2 RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS 2 3 IMPORTANT SAFEGUARDS 3 WORK AREA gt ce aau ees eee aia sasaw eens Fac RR ne 4 ELECTRICAL SAFETY 0 eects 4 PERSONAL SAFETY isses kr eye RE RR RU 4 5 TOOL USE AND CARE ssseeeeeee ee 5 SERVICE sias xta o teda Hd Rete soo RE NE 6 SECTION TWO SPECIFIC SAFETY RULES AND OR SYMBOLS 6 SAFETY RULES FOR CORDLESS DRILL DRIVERS 6 7 SYMBOLS ii ish bie inh einn a oe keiten d eee rid 7 SECTION THREE FUNCTIONAL DESCRIPTION a 8 BATTERY S docte S a a ai Sa yasa s de OE 9 11 REMOVING ATTACHING BATTERY PACK 10 CHARGER iis pach ss te ato lasla oe E RO TE Reo on 10 CHARGING BATTERY PACK 0 00 cece eee eee eee 11 ASSEMBLY vinci iai ees us IS We Mi ERE Ve ead 11 12 INSTALLING DRILL BIT INTO KEYLESS CHUCK 12 OPERATING THE CORDLESS DRILL 12 15 VARIABLE SPEED TRIGGER SWITCH 13 FORWARD REVERSE AND TRIGGER LOCK LEVER 13 TORQUE SETTINGS ooun 13 14 HIGH LOW SPEED GEAR SHIFTING 14 SCREWDRIVING ree ee da ER nen tea 14 DRILLING METAL rr rr 14 DRILLING MASONRY sssssssee e 14 DRI
23. ail Buyer Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying KAWASAKI portable power tool and no one else all parts of the product except those parts referred to below which are specifically excluded from such warranty see Exclusions to be free from defects in materials and workmanship for a period of two years from original date of purchase SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS This Kawasaki portable power tool is offered as a home use tool and carries a HOME USE WARRANTY This tool is made for home use in the execution of projects and repairs in and around the home Use of the tool for COMMERCIAL PURPOSES OR ON A JOBSITE is not covered under this warranty The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession custody or control of the product whichever occurred first This warranty shall be null and void if the product or any component thereof is modified altered or used for any commercial purpose or on a jobsite This warranty does not apply to any other product and or component thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Alltrade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF Warranty Perfo
24. battery for optimal performance Charge battery pack at ambient temperatures between 50 F 104 F Store tool and battery pack in locations where temperatures will not exceed 120 F This is important to prevent serious damage to the battery cells The battery pack should always be recharged when the Cordless Drill begins to run slowly When battery pack is not in use keep it away from other metal objects such as paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause sparks burns or fire REM OVING ATTACHING BATTERY PACK T ee Joe m REM OVE BATTERY PACK 1 Press both release buttons on either side of the Cordless Drill to release the battery pack 2 Pull battery pack free of Cordless Drill ATTACH BATTERY PACK 1 Align the raised portion of the battery pack with the groove in the battery compartment of the Cordless Drill Po Press the battery pack into place Make sure the latches are securely fastened Do not use the Cordless Drill if the battery pack is not seated properly po CHARGER nacssia 4 WARNING Before using battery charger please read carefully all instructions and cautionary markings on battery charger battery pack and product using battery Use only the charger which accompanied your product or direct replacement as listed in this manual Do not subst
25. be effective for only 90 days from the original date of purchase if this tool is used for any COMMERCIAL OR RENTAL PURPOSE The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession custody or control of the product whichever occurred first This warranty shall be null and void if the product or any component thereof is modified or altered This warranty does not apply to any other product and or component thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Alltrade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF Warranty Performance By purchasing the product purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and or part is promptly returned to Alltrade s facility postage pre paid and insured address ALLTRADE Warranty Claims amp Repair 1431 Via Plata Long Beach CA 90810 Attn Customer Service 1 800 590 3723 within the applicable warranty period with a written request by purchaser that Alltrade repair and or replace the nonconforming item and or part We recommend that you keep the original prod
26. d hat or hearing protection must be used for appropriate conditions A CAUTION Use clamps or other practical ways to secure and support the workpiece to a stable platform Holding the work by hand or against your body is unstable and may lead to loss of control Do not force tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for which it is designed Do not use the tool if the power switch does not turn it ON or OFF A tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect battery pack from tool or place the switch in the locked or OFF posi tion before making any adjustments changing accessories or storing the tool Such preventative safety measures reduce the risk of starting the tool accidentally Store idle tools out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery termi nals together may cause sparks burns or a fire Maintain tools with care Keep cutting tools sharp and clean Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control Check for misalignment or binding of moving parts breakage of
27. e When the battery pack becomes keyless chuck taking care to discharged and is hot the red light on the charger will flash When the battery keep the bit in the center of pack cools down the red light will glow continuously to indicate fast charging the jaws of the chuck mode 1 hour charge time This will occur when continuous use of your Cordless 99 Turn the front end of the chuck clockwise to hold the bit in place A Tighten securely by turning the front end of the chuck clockwise while holding Drill causes the battery pack to become hot It does not occur under normal the rear end circumstances OPERATING THE DRILL 4 WARNING Never tape the trigger switch down to provide continu ous high speed The tool may fail under such conditions causing fire or personal injury VARIABLE SPEED TRIGGER SWITCH THIS TOOL IS CONTROLLED BY A TRIGGER SWITCH The speed of the Cordless Drill depends on the amount of pressure you put on the trigger esas TRIGGER The more pressure you apply the faster SWITCH the Cordless Drill will go Release the pressure and the Cordless Drill will slow down Be sure the trigger is released when changing the position of the lever Always store the tool in the LOCKED OFF position Always check the direction of the Cordless Drill s rotation before use TO SELECT THE DIRECTIONS OF ROTATION To select forward Cordless Dril
28. e and pay particular attention to all the DANGER WARNING CAUTION and NOTE statements of this manual A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE NOTE provides additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood IMPORTANT SAFEGUARDS 4 DANGER People with electronic devices such as pacemakers should consult their physician s before using this product Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of California to cause cancer birth defects or other reproduct
29. ecommended operating and maintenance procedures also voids warranty This limited warranty does not apply to accessory items such as drill bits screwdriving bits circular saw blades jigsaw blades grinding wheels sanding sheets and other related items DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUSE NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY Alltrade will not be liable for the following labor charges loss or damage resulting from improper operation maintenance or repairs made by other persons pre delivery services such as assembly oil or lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Alltrade Repair Parts will void warranty Warranty Disclaimers EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY PROVIDED ABOVE ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AN
30. efully all instructions and cautionary markings on battery charger battery pack and product using battery Use only the charger which accompanied your product or direct replacement as listed in this manual Do not substitute any other charger Use only Alltrade approved chargers with your product Do not disassemble charger Do not use charger if it has been damaged left outdoors in the rain snow wet or damp environments or immersed in liquid The battery pack and charger heat during charging Place the charger on a flat non flammable surface away from flammable materials with at least four inches of clearance to allow proper air circulation around the charger and battery pack When the battery pack requires recharging a 1 hour charge allows the tool to operate at full power A charging indicator light on the charger will illuminate to show that charging is taking place CHARGE BATTERY PACK Plug the charger into 1 6 Make sure the trigger Insert the battery pack into CHARGING BATTERY PACK BATTERY NS the nearest 120 volt electrical outlet on the Cordless Worklight is in the OFF position and remove the battery pack from the Worklight LED LIGHT the charger Be sure that the battery pack is fully seated in the charger Do not force BATTERY CHARGER The red indicator light should come ON indicating that the battery pack is in a Fast Charge mode If the green indicator l
31. er storage or freight damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow recommended operating and maintenance procedures also voids warranty This limited warranty does not apply to accessory items such as drill bits screwdriving bits circular saw blades jigsaw blades grinding wheels sanding sheets and other related items DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUSE NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY Alltrade will not be liable for the following labor charges loss or damage resulting from improper operation maintenance or repairs made by other persons pre delivery services such as assembly oil or lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Alltrade Repair Parts will void warranty Warranty Disclaimers EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY PROVIDED ABOVE ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE
32. h another battery pack Use power tools only with specifically designated battery packs Use of any other battery packs may create a risk of injury and fire When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause burns or a fire Under abusive conditions liquid may be ejected from the battery avoid contact If contact accidentally occurs flush with water If liquid contacts eyes additionally seek medical help Liquid ejected from the battery may cause irritation or burns SERVICE Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained SAFETY RULES FOR WORKLIGHT CAUTION Use battery operated tool only with specifically designated battery pack Use of any other batteries may create risk of fire Keep the handle of the Worklight dry clean and free from oil and grease Do not run the Worklight while carrying it at your side The worklight heats up immediately when in use and could result in burns Do not use the Worklight if it has been damaged left outdoors in the rain snow wet or damp environments or immersed in liquid Maintain labels and nameplates on the Worklight These carry important informa tion If unreadable
33. her hand swivel the head of the Worklight counter clockwise until it is at the angle you desire Swivel the head of the Worklight clockwise to return it to its original position REPLACING THE LIGHT BULB This Worklight uses a Krypton 18V 0 3A light bulb Use of any other kind of light bulb may cause damage or injury Parts of this worklight heat up almost immediately when in use To avoid burns use caution when handling light bulb and metal reflector Never change a hot light bulb Bulb must be cool to the touch before attempting to remove or replace it 10 For your convenience a spare light bulb is included inside the unit Unscrew the rim and carefully remove it from the light assembly Remove the battery pack from the Worklight Hold the top of the Worklight with one hand while twisting the rim in a counter clockwise direction with the other Continue turning until the rim comes loose REPLACEMENT Po 99 Remove the bulb by turning it slightly and pulling it out of the bulb fitting Be careful not to damage the delicate parts inside the case Insert the new bulb then carefully put the rim back in place and turn it clockwise to tighten it MAINTENANCE AND CLEANING 4 WARNING Always remove the battery pack before attempting cleaning or maintenance Use only mild soap and a damp cloth to clean the tool Never let any liquid get inside the casing Never immerse any pa
34. hooses to replace the product it may replace it with a new or reconditioned one of the same or comparable design The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period Typically a defective product that is returned within the first 30 days after the purchase date will be replaced for items returned after the first 30 days and within the warranty period covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option During the warranty period Alltrade will be responsi ble for the return shipping charges Alltrade s repair and or replacement of any non conforming item and or part thereof shall constitute fulfillment of all obligations to the purchaser Alltrade shall not be responsible or liable for any expense including freight charges or repairs made outside Alltrade s facility unless expressly agreed to by Alltrade in writing Under no circumstances shall Alltrade bear any responsibility for loss of the unit loss of time or rental inconvenience commercial loss or consequential damages 14 Exclusions This warranty does not cover parts damaged due to normal wear abnormal conditions misapplication misuse abuse accidents operation at other than recommended pressures or temperatures improper storage or freight damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow r
35. ight comes ON then the battery is already fully charged After approximately one hour of charging the red indicator light should go OFF and the green light should come ON indicating that the battery is fully charged and the charger is now in a Trickle Charge mode The battery can be left in a Trickle Charge mode until ready to use IMPORTANT INFORM ATION FOR RECHARGING HOT BATTERIES When using your Worklight continuously the batteries in your battery pack will become hot You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge When the battery pack becomes discharged and is hot the red light on the charger will flash When the battery pack cools down the red light will glow continuously to indicate fast charging mode 1 hour charge time NOTE This will occur when continuous use of your Worklight causes the battery pack to become hot It does not occur under normal circumstances OPERATING THE WORKLIGHT 4 WARNING Parts of this Worklight heat up almost immediately when in use To avoid burns use caution when handling light bulb and metal reflector Never change a hot light bulb Bulb must be cool to the touch before attempting to remove or replace it OPERATING THE ON OFF SWITCH Press the ON OFF switch to turn the worklight ON and OFF ADJUSTING THE WORKLIGHT BEAM Hold the handle of the Worklight securely in one hand With the ot
36. ing battery Do not incinerate the battery pack even if it is severely dam aged or is completely worn out The battery pack can explode Do not carry battery packs in aprons pockets or tool boxes product kit boxes drawers etc with loose metal objects Battery pack terminals could be short circuited causing damage to the battery pack severe burns or fire The battery pack is Nickel Cadmium Ni Cad and is considered to be a toxic material by the Environmental Protection Agency Before disposing of dam aged or worn out Ni Cad battery packs check with your State Environmental Protection Agency to find out about special restrictions on the disposal of these battery packs take them to your local recycling center for proper disposal or call 1 800 822 8837 NOTE The battery is not fully charged Before first use the battery pack requires 3 5 hours charge time to be fully charged Subsequent recharging needs 1 hour for the battery to be fully charged Always switch to a fresh battery when tool performance begins to diminish Severe heat is most destructive to a battery the more heat generated the faster the battery loses power A battery that gets too hot can have a shortened life Never over discharge a battery by using the tool even after tool performance has decreased Do not attempt to discharge a tool s battery by continuing to pull on the tool trigger When tool performance begins to diminish stop the tool and recharge the
37. itute any other charger Use only Alltrade approved chargers with your product Do not disassemble charger Do not use charger if it has been damaged left outdoors in the rain snow wet or damp environments or immersed in liquid The battery pack and charger heat during charging Place the charger on a flat non flammable surface away from flammable materials with at least four inches of clearance to allow proper air circulation around the charger and battery pack When the battery pack requires recharging a 1 hour charge allows the tool to operate at full power A charging indicator light on the charger will illuminate to show that charging is taking place 10 CHARGING BATTERY PACK ASSEMBLY CHARGE BATTERY PACK BATTERY PACK Plug the charger into the nearest 120 volt electrical outlet WARNING Be aware that this tool is always in an operating condition because it does not have to be plugged into an electrical outlet Always turn the switch OFF and remove the battery pack before changing bits Po Make sure the trigger on the Cordless Drill is in the OFF position and remove the battery pack from the Cordless Drill 3 Insert the battery pack into the charger Be sure INSTALLING DRILL BIT INTO KEYLESS CHUCK A WARNING Before inserting a drill bit or other accessory make sure the forward reverse and trigger lock lever is in the center OFF position to prevent accidental start
38. ive harm Some examples of these chemicals are Lead from lead based paints Crystalline silica from bricks and cement and other masonry products and arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles WARNING Handling the power cord on corded products may expose you to lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WARNING Keep your work area clean and well lit Cluttered work benches and dark work areas may cause accidents or injury Do not operate power tools in explosive areas such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep bystanders children and visitors away while operating a power tool Distractions can cause you to lose control A WARNING Do not abuse the cord Never use the cord to carry the tool Keep the cord away from heat oil sharp edges or moving parts Replace damaged cords immediately Damaged cords may create a fire A battery operated tool with integral batteries or a separate battery pack
39. l rotation press the trigger lock from left to right flat against the Cordless Drill body To select reverse press the trigger lock lever in the opposite direction The center position locks the tool TORQUE SETTINGS NOTE To prevent damaging the tool or driving screw too deep into work piece release the trigger when you feel the clutch slip THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE CONTROL RING For light duty work use lower settings JE e For heavy duty work use higher settings PROPER SETTING FOR DRIVING SCREWS 1 Set the ring on the lowest setting to begin Po Try tightening the first screw If the drill drives smoothly proceed with the next screw 99 If the Drill s clutch slips increase the torque setting and try again until the Drill drives the screw without incident HIGH LOW SPEED GEAR SHIFTING LOW SPEED FOR LOW SPEED SETTING HIGH SPEED Slide the switch on top of the Drill to Position 1 for high torque applications and driving screws FOR HIGH SPEED SETTING Slide the switch to Position 2 for light duty projects SCREWDRIVING WHEN DRIVING FASTENERS Always start slowly and gradually increase the speed of the Drill Release the trigger when you feel the clutch slip Always keep the driver bit straight to prevent damage to the screw Hold the Drill with both hands to ensure control if the bit should stick or slip To p
40. must be recharged only with the specified charger for the battery A charger that may be suitable for one type of battery may create a risk of fire when used with another battery Use battery operated tool only with specifically designated battery pack Use of any other batteries may create risk of fire A WARNING Stay alert watch what you are doing and use common sense when operat ing a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Avoid accidental starting Be sure switch is in the locked or OFF position before inserting battery pack Carrying power tools with your finger on the switch or inserting battery pack into a tool with the power switch ON invites accidents WARNING Remove adjusting keys or wrenches before turning the tool ON A wrench or a key that is left attached to a rotating part of the tool may result in personal injury Do not overreach Keep proper footing and balance at all times Proper foot ing and balance enable better control of the tool in unexpected situations Use safety equipment Always wear eye protection Dust mask non skid safe ty shoes har
41. nd W Watt Power Kg Kilograms Weight N Alternating Current Type of Current Direct Current Type of Current Alternating or Direct Current Type of Current Earthing Terminal Grounding Terminal E Class II Construction Denotes Double Insulation min Minutes Time S Seconds Time j Diam eter Size of Drill Bits Grinding Wheels etc n No load speed No load Rotational Speed min Revolutions per Minute Revolutions Surface Speed Strokes etc per Minute 1 23 Ring Selector Settings Speed Torque or Position Settings PROTECTING THE ENVIRONMENT BATTERIES Alltrade batteries can be recharged many times At the end of their useful life recy cle batteries with due care for our environment Ni Cad and Ni MH batteries are recyclable Take them to your local recycling center or call 1 800 822 8837 Collected batteries will be recycled or disposed of properly OTHER CONSUMER DO IT YOURSELF DIY TOOLS Alltrade offers a full range of Kawasaki tools that make DIY jobs easy If you would like further information on the following products please contact Alltrade Customer Service Department at 1 800 590 3723 Cordless Drills Screwdrivers Impact Wrenches Sanders Jigsaws Circular Saws Angle Grinders Reciprocating Saws Routers Rotary Tools Corded and Cordless Multi Purpose Tools Wide Range of Accessories and more 2 YEAR LIMITED HOME USE WARRANTY Express and Exclusive Limited Home Use Warranty to Original Ret
42. oderate injury 4 CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage CAUTION NOTE provides additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood NOTE WARNING Before using battery pack please read carefully all instructions and cautionary markings on battery pack battery charger and product using battery Do not incinerate the battery pack even if it is severely dam aged or is completely worn out The battery pack can explode Do not carry battery packs in aprons pockets or tool boxes product kit boxes drawers etc with loose metal objects battery pack terminals could be short circuited causing damage to the battery pack severe burns or fire The battery pack is Nickel Cadmium Ni Cad and is considered to be a toxic material by the Environmental Protection Agency Before disposing of dam aged or worn out Ni Cad battery packs check with your State Environmental Protection Agency to find out about special restrictions on the disposal of these battery packs take them to your local recycling center for proper disposal or call 1 800 822 8837 NOTE The battery is not fully charged Before first use the battery pack requires 8 10 hours charge time to be fully charged Subsequent recharging needs 3 5 hours for the battery to be
43. omer Service Department toll free at 1 800 590 3723 for general repair information and charges 16 F0R CUSTOMER SERVICE P0UR LE SERVICE APR S VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1 800 590 3723 Printed in China Kawasaki Kawasaki Motors Corp U S A OFFICIAL LICENSED PRODUCT 87 1904 60957 KAWASAKI IS A TRADEMARK LICENSED BY KAWASAKI MOTORS CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO COPYRIGHT 2006 ALLTRADE TOOLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 840138 19 2V Battery Pack Rev 7 10 06 COMPONENT Kawas aki 4840138 19 2V BATTERY PACK INSTRUCTION MANUAL SF THS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE OF THS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS INSTRUCTIONS AND PRODUCT LABELS FAILURE TODO SOCOULD RESULT IN SERIOUS PERSONAL IN URY AND OR PROPERTY DAMAGE IF YOU SHOULD HAVE ANY QUESTIONS CR EXPERIENCE A PROBLEM WTH YOUR ALLTRADE PRODUCT DO NOT RETURN THS PRODUCT TO THE STORE PLEASE CALL CUR CUSTOMER SERVICE DEPARTMENT AT 1 800 590 3723 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL NO DATE PURCHASED AND STORE LOCATION AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE IF YOU WOULD LIKE TO MAKE A SUGGESTION OR COMMENT GVE US A CALL OR EMAIL US AT INFO
44. or part will be repaired and or replaced If the unit is repaired new or reconditioned replacement parts may be used If Alltrade chooses to replace the product it may replace it with a new or reconditioned one of the same or comparable design The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period Typically a defective product that is returned within the first 30 days after the purchase date will be replaced for items returned after the first 30 days and within the warranty period covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option During the warranty period Alltrade will be responsi ble for the return shipping charges Alltrade s repair and or replacement of any non conforming item and or part thereof shall constitute fulfillment of all obligations to the purchaser Alltrade shall not be responsible or liable for any expense including freight charges or repairs made outside Alltrade s facility unless expressly agreed to by Alltrade in writing Under no circumstances shall Alltrade bear any responsibility for loss of the unit loss of time or rental inconvenience commercial loss or consequential damages Exclusions This warranty does not cover parts damaged due to normal wear abnormal conditions misapplication misuse abuse accidents operation at other than recommended pressures or temperatures improp
45. r environment Ni Cad and Ni MH batteries are recyclable Take them to your local recycling center or call 1 800 822 8837 Collected batteries will be recycled or disposed of properly OTHER CONSUMER DO IT YOURSELF DIY TOOLS Alltrade offers a full range of Kawasaki tools that make DIY jobs easy If you would like further information on the following products please contact Alltrade Customer Service Department at 1 800 590 3723 Cordless Drills Screwdrivers Impact Wrenches Sanders Jigsaws Circular Saws Angle Grinders Reciprocating Saws Routers Rotary Tools Corded and Cordless Multi Purpose Tools Wide Range of Accessories and more 3 YEAR LIMITED WARRANTY Express and Exclusive Limited Warranty to Original Retail Buyer Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying KAWASAKI power tool and no one else all parts of the product except those parts referred to below which are specifically exclud ed from such warranty see Exclusions to be free from defects in materials and workmanship for a period of three years from original date of purchase except that such warranty with regard to the battery shall be for a period of two years from original date of purchase unless the tool is used for commercial or rental purposes SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE The above warranty for this Kawasaki power tool including the battery shall
46. revent wood from splitting drill pilot holes into the wood before driving in the screws 14 DRILLING METAL WHEN DRILLING HARD METALS Apply a lubricant such as cutting oil to the tip of the bit Start with a small hole then enlarge to the required size Make sure the bit is actually cutting and not spinning in the hole as this will dull the edges of the bit Keep enough pressure on the bit to keep it drilling through the material DRILLING MASONRY WHEN DRILLING MASONRY Masonry can be brittle so be careful not to apply too much pressure and crack the material Apply enough pressure to keep the bit cutting and not spinning in the hole as this will dull the edges of the bit Bricks and similar soft materials will require less pressure concrete will require much more DRILLING WOOD Use twist bits to drill holes in wood Make sure the bits are sharp Pull the bits out of the hole frequently to clear chips from the flutes as an overburdened bit may overheat HINTS FOR OPTIMUM USE DRILLING Keep the right amount of pressure in a straight line with the drill bit Too little and the bit will spin without cutting too much and the motor may stall Just before the drill tip breaks though the other side of the work piece drill more slowly and decrease pressure on the tool This will prevent stalling and leave a cleaner hole Use a block of wood to back up work pieces that may splinter Use spade bits
47. rmance By purchasing the product purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and or part is promptly returned to Alltrade s facility postage pre paid and insured address ALLTRADE Warranty Claims amp Repair 1431 Via Plata Long Beach CA 90810 Attn Customer Service 310 590 3723 within the applicable warranty period with a written request by purchaser that Alltrade repair and or replace the nonconforming item and or part We recommend that you keep the original product packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit damage When sending your product include your name address phone number dated proof of purchase or copy and a statement about the nature of problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insured to Alltrade s facility see above address will be inspected and at Alltrade s option repaired and or replaced free of charge if found to be defective and subject to warranty Alltrade retains the sole discretion to determine whether any item or part is nonconforming and if so whether the item and
48. rranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and or part is promptly returned to Alltrade s facility postage pre paid and insured address ALLTRADE Warranty Claims amp Repair 1431 Via Plata Long Beach CA 90810 Attn Customer Service 1 800 590 3723 within the applicable warranty period with a written request by purchaser that Alltrade repair and or replace the nonconforming item and or part We recommend that you keep the original product packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit damage When sending your product include your name address phone number dated proof of purchase or copy and a statement about the nature of problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insured to Alltrade s facility see above address will be inspected and at Alltrade s option repaired and or replaced free of charge if found to be defective and subject to warranty Alltrade retains the sole discretion to determine whether any item or part is nonconforming and if so whether the item and or part will be repaired and or replaced If the unit is repaired new or reconditioned replacement parts may be used If Alltrade c
49. rt can cause loss of control and injury Position yourself to avoid being caught between the tool or side handle and walls or posts Should the socket or bit become bound in the work the reaction torque of the tool could crush your hand or leg Check to see that keys and adjusting wrenches are removed from the Cordless Drill before switching the tool ON Keys or wrenches can fly away at high velocity striking you or a bystander When using the Cordless Drill always maintain a firm grip on the tool with both hands Keep the handle of the Cordless Drill dry clean and free from oil and grease Do not run the Cordless Drill while carrying it at your side A spinning socket or bit could become entangled with clothing and injury may result Disconnect the plug or remove the battery pack from tool and place the switch in the locked or OFF position before making any assembly adjustments changing accessories performing any inspection maintenance or cleaning procedures Such preventive safety measures reduce the risk of starting the tool accidentally 4 CAUTION Do not use the Cordless Drill if it has been damaged left outdoors in the rain snow wet or damp environments or immersed in liquid Maintain labels and nameplates on the Cordless Drill These carry important information If unreadable or missing contact Alltrade for a replacement IMPORTANT Some of the following symbols may be used on your tool Please stud
50. rt of the tool in a liquid Always keep the ventilation openings clear Always clean the battery pack using only a dry cloth Do not use liquids Always unplug the charger before cleaning it Regularly clean the ventilation slots in your tool and charger using only a soft brush or dry cloth Never open the Worklight case battery pack or charger Do not attempt to repair the Worklight battery pack or charger yourself Opening any of these parts will void your warranty A CAUTION Use only authorized replacement parts for your tool 11 Equipment service must be performed only by qualified repair personnel using authorized replacement parts Service or maintenance by unqualified personnel could result in considerable risk of personal injury Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury ACCESSORIES Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool Always attach grounded 3 prong extension cords to grounded 3 hole outlets If you must use an extension cord be sure that the gauge is large enough to carry the amount of current necessary for your power tool If not your tool may experience a loss of power excessive voltage drop or overheating The smaller the gauge number the heavier the cord see table below RECOMMENDED SIZES OF EX
51. s that may result in injury that the battery pack is CHARGER Do not attempt to tighten drill bits or any other accessory by gripping the fully seated in the charger front of the chuck and turning the tool on This may cause personal injury Do not force and or damage to the chuck 4 The red indicator light should come ON indicating that the battery pack is in When removing the bit from the tool avoid contact with skin and use proper a Fast Charge mode If the green indicator light comes ON then the battery protective gloves when grasping the bit or accessory Accessories may be hot is already fully charged after prolonged use 5 After approximately one hour of charging the red indicator light should go OFF and the green light should come ON indicating that the battery is fully charged and the charger is now in a Trickle Charge mode Hold the rear end of the chuck in one hand and use the other hand to rotate the front end in a 6 The battery can be left in a Trickle Charge mode until ready to use counterclockwise direction to LOOSEN IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES open the jaws of the Chuck mamme When using your Cordless Drill continuously the batteries in your battery pack 2 Insert the shank of the bit or TIGHTEN will become hot You should let a hot battery pack cool down for approximately other accessory fully into the 30 minutes before attempting to recharg
52. slots in your tool and charger using only a soft brush or dry cloth Never open the Cordless Drill case battery pack or charger Do not attempt to repair the Cordless Drill battery pack or charger yourself Opening any of these parts will void your warranty ACCESSORIES Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool Always attach grounded 3 prong extension cords to grounded 3 hole outlets If you must use an extension cord be sure that the gauge is large enough to carry the amount of current necessary for your power tool If not your tool may experi ence a loss of power excessive voltage drop or overheating The smaller the gauge number the heavier the cord see table below RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS TOOL CURRENT RATING CONDUCTOR SIZE IN A W G AMPERE 10FT 25FT 50FT 100FT 3 6 18 18 18 18 6 8 18 18 18 16 8 10 18 18 18 14 10 12 16 16 14 14 12 16 14 12 12 16 20 12 12 12 SPECIFICATIONS Voltage 19 2V Low Speed 0 440 min High Speed 0 1500 min Torque Settings 21 Drill Chuck Capacity max b 13mm 1 2 Charger Input 120V N 60Hz Charging Time Approx 1 hour Battery Type Ni Cad 17 PROTECTING THE ENVIRONMENT BATTERIES Alltrade batteries can be recharged many times At the end of their useful life recycle batteries with due care for ou
53. the tool even after tool performance has decreased Do not attempt to discharge a tool s battery by continuing to pull on the tool trigger When tool performance begins to diminish stop the tool and recharge the battery for optimal performance Charge battery pack at ambient temperatures between 50 F 104 F Store tool and battery pack in locations where temperatures will not exceed 120 F This is important to prevent serious damage to the battery cells The battery pack should always be recharged when the Cordless Worklight begins to dim When battery pack is not in use keep it away from other metal objects such as paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause sparks burns or fire REMOVING ATTACHING BATTERY PACK REM OVE BATTERY PACK 1 Press both release buttons on either side of the Cordless Worklight to release the battery pack 2 Pull battery pack free of Cordless Worklight ATTACH BATTERY PACK Align the raised portion of the battery pack with the groove in the battery compart ment of the Cordless Worklight Press the battery pack into place Make sure the latches are securely fastened Do not use the Cordless Worklight if the battery pack is not seated properly Po RELEASE BUTTON CHARGER 4 WARNING Before using battery charger please read car
54. the warranty period Alltrade will be responsi ble for the return shipping charges Alltrade s repair and or replacement of any non conforming item and or part thereof shall constitute fulfillment of all obligations to the purchaser Alltrade shall not be responsible or liable for any expense including freight charges or repairs made outside Alltrade s facility unless expressly agreed to by Alltrade in writing Under no circumstances shall Alltrade bear any responsibility for loss of the unit loss of time or rental inconvenience commercial loss or consequential damages Exclusions This warranty does not cover parts damaged due to normal wear abnormal conditions misapplication misuse abuse accidents operation at other than recommended pressures or temperatures improper storage or freight damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow recommended operating and maintenance procedures also voids warranty This limited warranty does not apply to accessory items such as drill bits screwdriving bits circular saw blades jigsaw blades grinding wheels sanding sheets and other related items DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUSE NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES COMMERCIAL AND RENTAL APPLICATIONS OR OTH
55. uct packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit damage When sending your product include your name address phone number dated proof of purchase or copy and a statement about the nature of problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insured to Alltrade s facility see above address will be inspected and at Alltrade s option repaired and or replaced free of charge if found to be defective and subject to warranty Alltrade retains the sole discretion 19 to determine whether any item or part is nonconforming and if so whether the item and or part will be repaired and or replaced If the unit is repaired new or reconditioned replacement parts may be used If Alltrade chooses to replace the product it may replace it with a new or reconditioned one of the same or comparable design The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period Typically a defective product that is returned within the first 30 days after the purchase date will be replaced for items returned after the first 30 days and within the warranty period covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option During
56. ve other rights which vary from state to state If your product is not covered by this warranty please call our Customer Service Department toll free at 1 800 590 3723 for general repair information and charges
57. y them and learn their meaning Proper interpretation of these symbols will allow you to operate the tool better and safer SYMBOL NAME EXPLANATION V Volts Voltage Potential A Amperes Current Hz Hertz Frequency Cycles per Second W Watt Power Kg Kilograms Weight N Alternating Current Type of Current Direct Current Type of Current Alternating or Direct Current Type of Current Earthing Terminal Grounding Terminal El Class II Construction Denotes Double Insulation min Minutes Time S Seconds Time j Diam eter Size of Drill Bits Grinding Wheels etc n No load speed No load Rotational Speed min Revolutions per Minute Revolutions Surface Speed Strokes etc per Minute 1 2 3 Ring Selector Settings Speed Torque or Position Settings FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS 1 Battery Pack 8 High Low Speed Switch 2 Release Buttons on Each Side 9 Variable Speed Controlled 3 Charger Trigger Switch 4 Indicator Lights 10 Accessory Bit Holder 5 12 7mm 1 2 Keyless Chuck 11 Comfort Rubber Grip 6 22 Adjustable Torque Settings Control Ring ACCESSORIES 7 Forward Reversing and 12 Double Ended Screwdriver Bits 2 Trigger Lock Lever COMPONENT MODEL NUMBER BATTERY PACK 690549 CHARGER 690543 12 7mm 1 2 KEYLESS CHUCK 690552 A WARNING Before using battery pack please read carefully all instruc tions and cautionary markings on battery pack battery charger and product us

Kawasaki 840138-1HR User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents