Kawasaki 840135 User's Manual
Contents
1. COPYRIGHT 2006 ALLTRADE TOOLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 840051 19 2V Battery Pack Rev 7 24 06 COMPONENT Kawasaki a 19 2V BATTERY PACK INSTRUCTION MANUAL THS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE CF THS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS INSTRUCTIONS AND PRODUCT LABELS FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL IN URY AND OR PROPERTY DAMAGE IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT DO NOT RETURNTHS PRODUCT TO THE STORE PLEASE CALL OUR CLETOMER SERMCE DEPARTMENT AT 1 800 590 3723 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL No DATE PURCHASED AND STORE LOCATION AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE IF YOU WOULD LIKE TO MAKE A SUGGESTION OR COMMENT GVE US A CALL CR EMAIL US AT INFO ALLTRADETOOLS COM YOUR FEEDBACK IS MTAL TO US CONGRATULATIONS Thanks for choosing this product At Alltrade our aim is to provide you with quality products at an affordable price and we want you to be totally satisfied with your product and our Customer Service If any help and advice is needed please contact us at 1 800 590 3723 Properly cared for this tool will give you many years of satisfaction INTENDED USE This tool is intended for consumer use only Your charger and or adapter has been designed for charging ba2. DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury 4 DANGER WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A WARNING CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury 4 CAUTION CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE NOTE provides additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood IMPORTANT SAFEGUARDS People with electronic devices such as pacemakers should consult their physician s before using this product Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paints Crystalline silica from bricks and cement and other masonry products and arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of wo
3. pack into battery charger When the battery is placed in the charger the red LED BATTERY indicator light will remain on CHARGER D ao When fully charged reattach battery pack onto Cordless Drill making certain latches fasten securely Cordless Drill will not operate properly if the battery pack is not seated properly ASSEMBLY 4 WARNING Be aware that this tool is always in an operating condition because it does not have to be plugged into an electrical outlet Always turn the switch OFF and remove the battery pack before changing bits INSTALLING DRILL BIT INTO KEYLESS CHUCK A WARNING Before inserting a drill bit or other accessory make sure the forward reverse and trigger lock lever is in the center OFF position to prevent accidental starts that may result in injury Do not attempt to tighten drill bits or any other accessory by gripping the front of the chuck and turning the tool on This may cause personal injury and or damage to the chuck When removing the bit from the tool avoid contact with skin and use proper protective gloves when grasping the bit or accessory Accessories may be hot after prolonged use Hold the rear end of the chuck in one hand and use the other hand to rotate the front end in a counter RELEASE clockwise direction to open the jaws of the chuck HOLD HERE M Insert the shank of the bit or other accessory fully into the keyless chuck ta
4. Class II Construction Denotes Double Insulation min Minutes Time S Seconds Time Diameter Size of Drill Bits Grinding Wheels etc n No load speed No load Rotational Speed Imin Revolutions per Minute Revolutions Surface Speed Strokes etc per Minute 1 2 3 Ring Selector Settings Speed Torque or Position Settings OPERATING INSTRUCTIONS CONTROLS AND COMPONENTS 1 Rocker Switch 2 Gear Enclosure 3 Brush Caps 4 Anvil ACCESSORIES 5 Impact Sockets 4 6 Carbon Brushes 2 not shown COMPONENT MODEL NUMBER CARBON BRUSHES 690296 ROCKER SWITCH AND DIRECTION OF ROTATION To rotate the Impact Wrench in a clockwise direction press the lower portion of the Rocker Switch To rotate the Impact Wrench in a counter clockwise direction press the upper portion of the Rocker Switch ROCKER SWITCH COUNTER CLOCKWISE When installing a socket INSTALLING REMOVING SOCKET align the holes in the side of the socket with the dent cf pin Press the socket on until the dent pin engages in the hole To remove a socket depress the dent pin through the hole using a small pointed object and pull the socket off When removing the socket or bit from the tool avoid contact with skin and use proper protective gloves when grasping the socket bit or accessory Accessories may be hot after prolonged use MAINTENANCE AND CLEANING 4 WARNING Always UNPLUG the Impact Wrench fr
5. EVEN IF ALLTRADE AND OR ITS REPRESENTATIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES IN NO EVENT WHETHER AS A RESULT OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE Limitations on Warranty Disclaimers Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequential damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If your product is not covered by this warranty please call our Customer Service Department toll free at 1 800 590 3723 for general repair information and charges 22 FOR CUSTOMER SERVICE POUR LE SERVICE APRES VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1 800 590 3723 Printed in China Imprim dans la Chine Impreso en China Kawasaki Kawasaki Motors Corp U S A OFFICIAL LICENSED PRODUCT 87 1904 60957 KAWASAKI IS A TRADEMARK LICENSED BY KAWASAKI MOTORS CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO
6. KAWASAKI IS A TRADEMARK LICENSED BY KAWASAKI MOTORS CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO COPYRIGHT 2008 ALLTRADE TOOLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 840055 19 2V Cordless Drill Rev 2 7 08 COMPONENT Kawasaki dil 19 2V 2 SPEED BATTERY OPERATED DRILL INSTRUCTION MANUAL THS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE CF THS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS INSTRUCTIONS AND PRODUCT LABELS FAILURE TO DO SO GOULD RESULT IN SERIOUS PERSONAL IN URY AND OR PROPERTY DAMAGE IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT DO NOT RETURN THS PRODUCT TOTHE STORE PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1 800 590 3723 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL No DATE PURCHASED AND STORE LOCATION AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE IF YOU WOULD LIKE TO MAKE A SUGGESTION OR COMMENT GVE US A CALL OR EMAIL US AT INFO ALLTRADETOOLS COM YOUR FEEDBACK IS VITAL TOUS TABLE OF CONTENTS CONGRATULATIONS 0 0 cece ee nh 2 INTENDED USE 5 14 nie ETE ERR eH HERE RR qawaq 2 SECTION ONE GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS 2 RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS 2 3 IMPORTANT SAFEGUARDS l asas eee e
7. OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY Alltrade will not be liable for the following labor charges loss or damage resulting from improper operation maintenance or repairs made by other persons pre delivery services such as assembly oil or lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Alltrade Repair Parts will void warranty Warranty Disclaimers EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY PROVIDED ABOVE ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MER
8. any other condition that may affect the tool s operation If damaged have the tool serviced before using Many accidents are caused by poorly maintained tools Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may create a risk of injury when used on another tool A CAUTION Tool service must be performed only by qualified repair personnel Service or maintenance by unqualified personnel may result in a risk of injury When servicing a tool use only identical replacement parts This will ensure that the safety of the power tool is maintained Follow instructions in the Maintenance section of this manual Use of unauthorized parts or failure to fol low Maintenance Instructions may create a risk of shock or injury SPECIFIC SAFETY RULES AND OR SYMBOLS A CAUTION Hold tool by insulated gripping surfaces when per forming an operation where the cutting tool may contact hidden wiring Contact with a live wire will also make exposed metal parts of the tool live and shock the operator SAFETY RULES FOR CORDLESS DRILL DRIVERS A CAUTION Always wear safety goggles or eye protection when using this tool Use a dust mask or respirator for applications which generate dust Do not grasp the tool or place your hands too close to the spinning chuck or drill bit Your hand may be lacerated or may cause injury Secure the material being worked on N
9. etc with loose metal objects Battery pack terminals could be short circuited causing damage to the battery pack severe burns or fire The battery pack is Nickel Cadmium Ni Cad and is considered to be a toxic material by the Environmental Protection Agency Before disposing of dam aged or worn out Ni Cad battery packs check with your State Environmental Protection Agency to find out about special restrictions on the disposal of these battery packs take them to your local recycling center for proper disposal or call 1 800 822 8837 CONTROLS AND COMPONENTS NOTE 1 Battery Pack 9 High Low Speed Switch The battery is not fully charged Before first use the battery pack requires 2 Release Buttons on Each Side 10 Variable Speed Controlled 8 10 hours charge time to be fully charged Subsequent recharging needs 3 5 3 120V AC Adapter Trigger Switch hours for the battery to be fully charged 4 Charger 11 Accessory Bit Holder Always switch to a fresh battery when tool performance begins to diminish 5 LED Charging Indicator 12 Comfort Rubber Grip Severe heat is most destructive to a battery the more heat generated the faster 6 10mm 3 8 Keyless Chuck 13 Led Light the battery loses power A battery that gets too hot can have a shortened life 7 2441 Adjustable Torque Settings Never over discharge a battery by using the tool even after tool performance Control Ring ACCESSORIES has decreased Do not attempt to discharge a tool s batter
10. the charger specified by the manufacturer A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack Use power tools only with specifically designated battery packs Use of any other battery packs may create a risk of injury and fire When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery termi nals together may cause burns or a fire Under abusive conditions liquid may be ejected from the battery avoid con tact If contact accidentally occurs flush with water If liquid contacts eyes additionally seek medical help Liquid ejected from the battery may cause irrita tion or burns Store idle tools out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery termi nals together may cause sparks burns or a fire Maintain tools with care Keep cutting tools sharp and clean Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control Check for misalignment or binding of moving parts breakage of parts and
11. ventilation slots in your tool and charger using only a soft brush or dry cloth Never open the Cordless Drill case battery pack or charger Do not attempt to repair the Cordless Drill battery pack or charger yourself Opening any of these parts will void your warranty ACCESSORIES Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool Always attach grounded 3 prong extension cords to grounded 3 hole outlets If you must use an extension cord be sure that the gauge is large enough to carry the amount of current necessary for your power tool If not your tool may experi ence a loss of power excessive voltage drop or overheating The smaller the gauge number the heavier the cord see table on next page RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS TOOL CURRENT RATING CONDUCTOR SIZE IN A W G AMPERE 10FT 25FT 50FT 100FT 3 6 18 18 18 18 6 8 18 18 18 16 8 10 18 18 18 14 10 12 16 16 14 14 12 16 14 12 12 16 20 12 12 12 18 SPECIFICATIONS SPECIFICATIONS Voltage 19 2V No Load Low Speed 0 400 min No Load High Speed 0 1100 min Torque Settings 24 1 Drill Chuck Capacity Up to 10mm 3 8 Charger Input 120V N 60Hz Charging Time Approx 3 5 hours Battery Type Ni Cad PROTECTING THE ENVIRONMENT BATTERIES Alltrade batteries can be recharged many times At the end of their use
12. ANY BREACH OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRESENTATIVE S AND PURCHASER ANY WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOLD HEREUNDER EVEN IF ALLTRADE AND OR ITS REPRESENTATIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES IN NO EVENT WHETHER AS A RESULT OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE Limitations on Warranty Disclaimers Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequential damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If your product is not covered by this warranty please call our Customer Service Department at 1 310 522 9008 or toll free at 1 800 590 3723 for general repair information and charges 14 FOR CUSTOMER SERVICE POUR LE SERVICE APR S VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1 800 590 3723 Printed in China OFFICIAL LICENSED PRODUCT 87 1904 60957
13. CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS PRODUCT ALL EXPRESS AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE PURCHASER INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE Limitation Of Liability IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECTLY OR INDIRECTLY ANY BREACH OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRESENTATIVE S AND PURCHASER ANY WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOLD HEREUNDER
14. E NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY Alltrade will not be liable for the following labor charges loss or damage resulting from improper operation maintenance or repairs made by other persons pre delivery services such as assembly oil or lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Alltrade Repair Parts will void warranty Warranty Disclaimers EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY PROVIDED ABOVE ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND
15. FOR CUSTOMER SERVICE POUR LE SERVICE APR S VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1 800 590 3723 Printed in China Imprim dans la Chine French Impreso en China Spanish Kawasaki Kawasaki Motors Corp U S A OFFICIAL LICENSED PRODUCT 87 1904 60957 KAWASAKI IS A TRADEMARK LICENSED BY KAWASAKI MOTORS CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO COPYRIGHT 2005 ALLTRADE TOOLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 840135 1 2 Corded Impact Wrench COMPONENT Kawasaki v 1 2 IMPACT WRENCH KIT INSTRUCTION MANUAL THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE OF THIS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS INSTRUCTIONS AND PRODUCT LABELS FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND OR PROPERTY DAMAGE IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT DO NOT RETURN THIS PRODUCT TO THE STORE PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1 800 590 3723 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL No DATE PURCHASED AND STORE LOCATION AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE IF YOU WOULD LIKE TO MAKE A SUGGESTION OR COMMENT GIVE US A CALL OR EMAIL US AT INFO ALLTRADETOOLS COM YOUR FEEDBACK IS VITAL TO US TABLE OF CONTEN
16. NSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKM ANSHIP ARE NOT COVERED BY THIS WARRANTY Alltrade will not be liable for the following labor charges loss or damage resulting from improper operation maintenance or repairs made by other persons pre delivery services such as assembly oil or lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Alltrade Repair Parts will void warranty Warranty Disclaimers EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY PROVIDED ABOVE ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCL
17. NY WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOLD HEREUNDER EVEN IF ALLTRADE AND OR ITS REPRESENTATIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES IN NO EVENT WHETHER AS A RESULT OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE Limitations on Warranty Disclaimers Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequential damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If your product is not covered by this warranty please call our Customer Service Department toll free at 1 800 590 3723 for general repair information and charges
18. R DO IT YOURSELF DIY TOOLS 19 SECTION FIVE 2 YEAR LIMITED WARRANTY ssssssse eee 19 22 CONGRATULATIONS Thanks for choosing this product At Alltrade our aim is to provide you with quality products at an affordable price and we want you to be totally satisfied with your product and our Customer Service If any help and advice is needed please contact us at 1 800 590 3723 Properly cared for this tool will give you many years of satisfaction INTENDED USE This tool is intended for consumer use only Your charger and or adapter has been designed for charging batteries of the type approved and supplied with this tool GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS 4 WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating maintaining and cleaning power tools Always use common sense and pay particular attention to all the DANGER WARNING CAUTION and NOTE statements of this manual A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death
19. RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE ABOVE 13 WARRANTY IS MADE WITH REGARD TO THIS PRODUCT ALL EXPRESS AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE PURCHASER INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REM EDY IS AS STATED ABOVE Limitation Of Liability IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECTLY OR INDIRECTLY
20. RNING Before using battery charger please read carefully all instructions and cautionary markings on battery charger battery pack and product using battery NOTE The charger will not automatically turn OFF when the battery pack is fully charged The charging indicator light will remain ON until the charger is disconnected from the electrical outlet Use only the charger which accompanied your product or direct replacement as listed in this manual Do not substitute any other charger Use only Alltrade approved chargers with your product Do not disassemble charger Do not use charger if it has been damaged left outdoors in the rain snow wet or damp environments or immersed in liquid The battery pack and charger heat during charging Place the charger on a flat non flammable surface away from flammable materials with at least four inches of clearance to allow proper air circulation around the charger and battery pack 11 When the battery pack requires recharging a 3 5 hour charge allows the tool to operate at full power A charging indicator light on the charger will illuminate to show that charging is taking place CHARGING BATTERY PACK CHARGE BATTERY PACK z BATTERY PACK 1 Make sure the trigger on the Cordless Drill is in the OFF position and remove the battery pack from the Cordless Drill Plug 120V AC Adapter into household outlet and into side of battery charger Insert battery
21. TION To select forward Cordless Drill rotation press the trigger lock from left to right flat against the Cordless Drill body To select reverse press the trigger lock lever in the opposite direction The center position locks the tool TORQUE SETTINGS NOTE To prevent damaging the tool or driving screw too deep into work piece release the trigger when you feel the clutch slip CONTROL RING THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE For light duty work use lower settings For heavy duty work use higher settings PROPER SETTING FOR DRIVING SCREWS 1 Set the ring on the lowest setting to begin 2 Try tightening the first screw If the drill drives smoothly proceed with the next screw 3 If the Drill s clutch slips increase the torque setting and try again until the Drill drives the screw without incident HIGH LOW SPEED GEAR SHIFTING FOR LOW SPEED SETTING Slide the switch on top of the Drill to Position 1 for high torque applications and driv ing screws FOR HIGH SPEED SETTING Slide the switch to Position 2 for light duty projects LOW SPEED HIGH SPEED SCREWDRIVING WHEN DRIVING FASTENERS Always start slowly and gradually increase the speed of the Drill Release the trigger when you feel the clutch slip Always keep the driver bit straight to prevent damage to the screw Hold the Drill with both hands to ensure control if the bit sh
22. TS CONGRATULATIONS 2 INTENDED USE inre te mede ec Rr ga eN sus n x ERES 2 SECTION ONE RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS 2 3 IMPORTANT SAFEGUARDS 3 WORK AREA seise oen ee npe pia danai ea dec er enun qusa 4 ELECTRICAL SAFELY sa 028 bua dre ac t oat urs 4 PERSONAL SAFETY ipagi ea mha dnia a ees 4 TOOL USE AND CARE sssssssesee denera kunku 5 SERVICE semerre rt Rn ola Rc a hae kaa 5 SAFETY RULES FOR IMPACT WRENCHES 6 SECTION TWO SPECIFIC SAFETY RULES AND OR SYMBOLS 7 SYMBOLS 2 u 2 oss Sum ss nude Eo UMS 7 SECTION THREE OPERATING INSTRUCTIONS 8 9 ROCKER SWITCH AND DIRECTION OF ROTATION 9 INSTALLING REMOVING SOCKETS 9 SECTION FOUR MAINTENANCE AND CLEANING 0 0 00 cee ee 10 ACCESSORIES ica orice Wey eae dea ean pele hale RR 10 SPEGIFICATIONS L eatin eae ace Pte e ey ee eina 11 OTHER CONSUMER DO IT YOURSELF DIY TOOLS 11 SECTION FIVE 3 YEAR LIMITED WARRANTY ssssssss n eee 11 14 1 CONGRATULATIONS Thanks for choosing this product At Alltrade our aim is to provide you with quality products at an affordable price and we want you to be totally satisfied with your product and our Customer Service If any help and advice is needed please contact us at 1 800 590 3723 Properly cared for this tool will giv
23. USIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS PRODUCT ALL EXPRESS AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE PURCHASER INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE Limitation Of Liability IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECTLY OR INDIRECTLY ANY BREACH OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRESENTATIVE S AND PURCHASER A
24. adjusting keys or wrenches before turning the tool ON A wrench or a key that is left attached to a rotating part of the tool may result in personal injury Do not overreach Keep proper footing and balance at all times Proper foot ing and balance enable better control of the tool in unexpected situations Use safety equipment Always wear eye protection Dust mask non skid safe ty shoes hard hat or hearing protection must be used for appropriate conditions If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of these devices can reduce dust related hazards TOOL USE AND CARE 4 CAUTION Use clamps or other practical ways to secure and support the workpiece to a stable platform Holding the work by hand or against your body is unstable and may lead to loss of control Do not force tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for which it is designed Do not use the tool if the power switch does not turn it ON or OFF A tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect battery pack from tool or place the switch in the locked or OFF position before making any adjustments changing accessories or storing the tool Such preventative safety measures reduce the risk of starting the tool accidentally Recharge only with
25. ance Charge battery pack at ambient temperatures between 50 F 104 F Store tool and battery pack in locations where temperatures will not exceed 120 F This is important to prevent serious damage to the battery cells The battery pack should always be recharged when the Cordless Drill begins to run slowly When battery pack is not in use keep it away from other metal objects such as paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause sparks burns or fire SYMBOLS IMPORTANT Some of the following symbols may be used on your tool Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the tool better and safer SYMBOL NAME EXPLANATION V Volts Voltage Potential A Amperes Current Hz Hertz Frequency Cycles per Second W Watt Power Kg Kilograms Weight N Alternating Current Type of Current Direct Current Type of Current Alternating or Direct Current Type of Current Earthing Terminal Grounding Terminal E Class II Construction Denotes Double Insulation min Minutes Time S Seconds Time j Diameter Size of Drill Bits Grinding Wheels etc n No load speed No load Rotational Speed min Revolutions per Minute Revolutions Surface Speed Strokes etc per Minute 1 23 Ring Selector Settings Speed Torque or Position S
26. attery pack Use of any other batteries may create risk of fire Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock A WARNING Stay alert watch what you are doing and use common sense when operat ing a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Avoid accidental starting Be sure switch is in the locked or OFF position before inserting battery pack Carrying power tools with your finger on the switch or insert ing battery pack into a tool with the power switch ON invites accidents Remove
27. d defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option During the warranty period Alltrade will be responsi ble for the return shipping charges Alltrade s repair and or replacement of any non conforming item and or part thereof shall constitute fulfillment of all obligations to the purchaser Alltrade shall not be responsible or liable for any expense including freight charges or repairs made outside Alltrade s facility unless expressly agreed to by Alltrade in writing Under no circumstances shall Alltrade bear any responsibility for loss of the unit loss of time or rental inconvenience commercial loss or consequential damages Exclusions This warranty does not cover parts damaged due to normal wear abnormal conditions misapplication misuse abuse accidents operation at other than recommended pressures or temperatures improper storage or freight damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow recommended operating and maintenance procedures also voids warranty This limited warranty does not apply to accessory items such as drill bits screwdriving bits circular saw blades jigsaw blades grinding wheels sanding sheets and other related items DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUSE NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRA
28. e the battery pack even if it is severely dam aged or is completely worn out The battery pack can explode Do not carry battery packs in aprons pockets or tool boxes product kit boxes drawers etc with loose metal objects battery pack terminals could be short circuited causing damage to the battery pack severe burns or fire The battery pack is Nickel Cadmium Ni Cad and is considered to be a toxic material by the Environmental Protection Agency Before disposing of dam aged or worn out Ni Cad battery packs check with your State Environmental Protection Agency to find out about special restrictions on the disposal of these battery packs take them to your local recycling center for proper disposal or call 1 800 822 8837 NOTE The battery is not fully charged Before first use the battery pack requires 8 10 hours charge time to be fully charged Subsequent recharging needs 3 5 hours for the battery to be fully charged Always switch to a fresh battery when tool performance begins to diminish Severe heat is most destructive to a battery the more heat generated the faster the battery loses power A battery that gets too hot can have a shortened life Never over discharge a battery by using the tool even after tool performance has decreased Do not attempt to discharge a tool s battery by continuing to pull on the tool trigger When tool performance begins to diminish stop the tool and recharge the battery for optimal perform
29. e the correct tool for your application The correct tool will do the job better and safer at the rate for which it is designed Do not use the tool if the power switch does not turn it ON or OFF A tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the power cord plug from the power source before making any adjustments changing accessories or storing the tool Such preventive safety measures reduce the risk of starting the tool accidentally Store idle tools out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users Maintain tools with care Keep cutting tools sharp and clean Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the tool s operation If damaged have the tool serviced before using Many accidents are caused by poorly maintained tools Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may create a risk of injury when used on another tool SERVICE Tool service must be performed only by qualified repair personnel Service or maintenance by unqualified personnel may result in a risk of injury When servicing a tool use only identical replacement parts Follow instructions in the Maintenance section o
30. e you many years of satisfaction INTENDED USE This tool is intended for consumer use only RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating maintaining and cleaning power tools Always use common sense and pay particular attention to all the DANGER WARNING CAUTION and NOTE statements of this manual A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death IDANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury DANGER IWARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A WARNING ICAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage CAUTION NOTE provides additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood NOTE IMPORTANT SAFEGUARDS 4 DANGER People with electronic devices such as pacemakers should consult their physician s before using
31. each CA 90810 Attn Customer Service 310 522 9008 within the applicable warranty period with a written request by purchaser that Alltrade repair and or replace the nonconforming item and or part We recommend that you keep the original product packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit damage When sending your product include your name address phone number dated proof of purchase or copy and a statement about the nature of problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insured to Alltrade s facility see above address will be inspected and at Alltrade s option repaired and or replaced free of charge if found to be defective and subject to warranty Alltrade retains the sole discretion to determine whether any item or part is nonconforming and if so whether the item and or part will be repaired and or replaced If the unit is repaired new or reconditioned replacement parts may be used If Alltrade chooses to replace the product it may replace it with a new or reconditioned one of the same or comparable design The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period Typically a defective product that is returned within the first 30 days after the purchase date w
32. ee 3 WORK AREA edere see eroi rete d e eerie 4 ELECTRICAL SAFETY 0 cece cette ene 4 PERSONAL SAFETY u 0 eee cette ne 5 TOOL USEAND CARE inei aa ear does 5 6 ld TET 6 SECTION TWO SPECIFIC SAFETY RULES AND OR SYMBOLS 7 SAFETY RULES FOR CORDLESS DRILL DRIVERS 7 SYMBOES u suu supa akay iste Seas IAM DES aa su 8 SECTION THREE FUNCTIONAL DESCRIPTION u oua pioa peanda unquwaq 9 BATTERY ssec exe rre e arka Rd C dt ade 10 12 REMOVING ATTACHING BATTERY PACK 11 CHARGERS Lit Remate Roe i backed bard OR ana 11 CHARGING BATTERY PACK 12 ASSEMBLY 4i uet rne e per pn Inte dro ER dae d ec 13 INSTALLING DRILL BIT INTO KEYLESS CHUCK 13 OPERATING THE DRILL uuu eee 13 17 VARIABLE SPEED TRIGGER SWITCH 14 FORWARD REVERSE AND TRIGGER LOCK LEVER 14 TORQUE SETTINGS 1 0 0 eee 15 HIGH LOW SPEED GEAR SHIFTING 15 SCREWDRIVING 0 cette e 16 DRILLING METAL cer cette E eet wasa eo s 16 DRILLING MASONRY sssssseee eee 16 DRILLING WOOD sssssssee e 16 HINTS FOR OPTIMUM USE sssseseeeee nn 16 17 1 SECTION FOUR MAINTENANCE AND CLEANING 17 18 ACCESSORIES jiers pakene ern ER EQRORERGIDI CE Kk a seein es 18 SPECIFICA ONS c rette ttc ecd emer ta c e 19 PROTECTING THE ENVIRONMENT 19 OTHER CONSUME
33. ep the original product packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit damage When sending your product include your name address phone number dated proof of purchase or copy and a statement about the nature of problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insured to Alltrade s facility see above address will be inspected and at Alltrade s option repaired and or replaced free of charge if found to be defective and subject to warranty Alltrade retains the sole discretion to determine whether any item or part is nonconforming and if so whether the item and or part will be repaired and or replaced If the unit is repaired new or reconditioned replacement parts may be used If Alltrade chooses to replace the product it may replace it with a new or reconditioned one of the same or comparable design The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period Typically a defective product that is returned within the first 30 days after the purchase date will be replaced for items returned after the first 30 days and within the warranty period covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option D
34. ettings PROTECTING THE ENVIRONMENT BATTERIES Alltrade batteries can be recharged many times At the end of their useful life recy cle batteries with due care for our environment Ni Cad and Ni MH batteries are recyclable Take them to your local recycling center or call 1 800 822 8837 Collected batteries will be recycled or disposed of properly OTHER CONSUMER DO IT YOURSELF DIY TOOLS Alltrade offers a full range of Kawasaki tools that make DIY jobs easy If you would like further information on the following products please contact Alltrade Customer Service Department at 1 800 590 3723 Cordless Drills Screwdrivers Impact Wrenches Sanders Jigsaws Circular Saws Angle Grinders Reciprocating Saws Routers Rotary Tools Corded and Cordless Multi Purpose Tools Wide Range of Accessories and more 2 YEAR LIMITED HOME USE WARRANTY Express and Exclusive Limited Home Use Warranty to Original Retail Buyer Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying KAWASAKI portable power tool and no one else all parts of the product except those parts referred to below which are specifically excluded from such warranty see Exclusions to be free from defects in materials and workmanship for a period of two years from original date of purchase SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS This Kawasaki portable power tool is offered as a home use t
35. ever hold it in your hand or across your legs Unstable support can cause loss of control and injury Position yourself to avoid being caught between the tool or side handle and walls or posts Should the socket or bit become bound in the work the reac tion torque of the tool could crush your hand or leg Check to see that keys and adjusting wrenches are removed from the Cordless Drill before switching the tool ON Keys or wrenches can fly away at high velocity striking you or a bystander When using the Cordless Drill always maintain a firm grip on the tool with both hands Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring Contact with a live wire will also make exposed metal parts of the tool live and shock the operator Keep the handle of the Cordless Drill dry clean and free from oil and grease Do not run the Cordless Drill while carrying it at your side A spinning sock et or bit could become entangled with clothing and injury may result Disconnect the plug or remove the battery pack from tool and place the switch in the locked or OFF position before making any assembly adjustments changing accessories performing any inspection maintenance or cleaning procedures Such preventive safety measures reduce the risk of starting the tool accidentally Do not use the Cordless Drill if it has been damaged left outdoors in the rain snow wet or da
36. f this manual Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury SAFETY RULES FOR IMPACT WRENCHES CAUTION Use only impact sockets Non impact sockets may shatter or break causing injury and or damage Ensure fastener and or system will withstand the level of torque generated by the tool Excessive torque may cause breakage and possible personal injury Always wear safety goggles or eye protection when using this tool Use a dust mask or respirator for applications which generate dust Do not grasp the tool or place your hands too close to the spinning anvil Your hand may be lacerated or may cause injury Secure the material being worked on Never hold it in your hand or across your legs Unstable support can cause loss of control and injury Position yourself to avoid being caught between the tool or side handle and walls or posts Should the socket or bit become bound in the work the reaction torque of the tool could crush your hand or leg Check to see that keys and adjusting wrenches are removed from the Impact Wrench before switching the tool ON Keys or wrenches can fly away at high velocity striking you or a bystander When using the Impact Wrench always maintain a firm grip on the tool with both hands Keep the handle of the Impact Wrench dry clean and free from oil and grease Do not run the Impact Wrench while carrying it at your side A spinnin
37. ful life recycle batteries with due care for our environment Ni Cad and Ni MH batteries are recyclable Take them to your local recycling center or call 1 800 822 8837 Collected batteries will be recycled or disposed of properly OTHER CONSUMER DO IT YOURSELF DIY TOOLS Alltrade offers a full range of Kawasaki tools that make DIY jobs easy If you would like further information on the following products please contact Alltrade Customer Service Department at 1 800 590 3723 Cordless Drills Screwdrivers Reciprocating Saws Impact Wrenches Routers Sanders Rotary Tools Jigsaws Corded and Cordless Multi Purpose Tools Circular Saws Wide Range of Accessories and more Angle Grinders 2 YEAR LIMITED HOME USE WARRANTY Express and Exclusive Limited Home Use Warranty to Original Retail Buyer Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying KAWASAKI portable power tool and no one else all parts of the product except those parts referred to below which are specifically excluded from such warranty see Exclusions to be free from defects in materials and workmanship for a period of two years from original date of purchase 19 SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS This Kawasaki portable power tool is offered as a home use tool and carries a HOME USE WARRANTY This tool is made for home use in the execution of projects and repairs in and around the
38. g socket or bit could become entangled with clothing and injury may result Disconnect the plug from the power supply and place the switch in the locked or OFF position before making any assembly adjustments changing accessories performing any inspection maintenance or cleaning procedures Such preventive safety measures reduce the risk of starting the tool accidentally Do not use the Impact Wrench if it has been damaged left outdoors in the rain snow wet or damp environments or immersed in liquid Maintain labels and nameplates on the Impact Wrench These carry important information If unreadable or missing contact Alltrade for a replacement SPECIFIC SAFETY RULES AND OR SYMBOLS Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring Contact with a live wire will also make exposed metal parts of the tool live and shock the operator SYMBOLS IMPORTANT Some of the following symbols may be used on your tool Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the tool better and safer SYMBOL NAME EXPLANATION V Volts Voltage Potential A Amperes Current Hz Hertz Frequency Cycles per Second W Watt Power Kg Kilograms Weight N Alternating Current Type of Current Direct Current Type of Current Alternating or Direct Current Type of Current Earthing Terminal Grounding Terminal El
39. home Use of the tool for COMMERCIAL PURPOSES OR ON A JOBSITE is not covered under this warranty The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession custody or control of the product whichever occurred first This warranty shall be null and void if the product or any component thereof is modified altered or used for any commercial purpose or on a jobsite This warranty does not apply to any other product and or component thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Alltrade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF Warranty Performance By purchasing the product purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and or part is promptly returned to Alltrade s facility postage pre paid and insured address ALLTRADE Warranty Claims amp Repair 1431 Via Plata Long Beach CA 90810 Attn Customer Service 1 800 590 3723 within the applicable warranty period with a written request by purchaser that Alltrade repair and or replace the nonconforming item and or part We recommend that you ke
40. ill be replaced for items returned after the first 30 days and within the warranty period covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option During the warranty period Alltrade will be responsi ble for the return shipping charges Alltrade s repair and or replacement of any non conforming item and or part thereof shall constitute fulfillment of all obligations to the purchaser Alltrade shall not be responsible or liable for any expense including freight charges or repairs made outside Alltrade s facility unless expressly agreed to by Alltrade in writing Under no circumstances shall Alltrade bear any responsibility for loss of the unit loss of time or rental inconvenience commercial loss or consequential damages 12 Exclusions This warranty does not cover parts damaged due to normal wear abnormal conditions misapplication misuse abuse accidents operation at other than recommended pressures or temperatures improper storage or freight damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow recommended operating and maintenance procedures also voids warranty This limited warranty does not apply to accessory items such as drill bits screwdriving bits circular saw blades jigsaw blades grinding wheels sanding sheets and other related items DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUS
41. king care to keep the bit in the center of the jaws of the chuck HOLD HERE ao Turn the front end of the chuck clockwise to hold the bit in place qp Tighten securely by turning the front end of the chuck clockwise while holding the rear end OPERATING THE DRILL 4 WARNING Never tape the trigger switch down to provide continu ous high speed The tool may fail under such conditions causing fire or personal injury VARIABLE SPEED TRIGGER SWITCH THIS TOOL IS CONTROLLED BY A TRIGGER SWITCH The speed of the Cordless Drill depends on the amount of pressure you put on the trigger TRIGGER The more pressure you apply the faster SWITCH the Cordless Drill will go Release the pressure and the Cordless Drill will slow down BUILT IN LED LAMP Press the trigger switch to light up the lamp The lamp remains on while the trigger switch is being pressed The lamp goes out after releasing the trigger NOTE Use a dry cloth to wipe the dirt off the lens of lamp Be careful not to scratch the lens of lamp or it may lower the illumination A CAUTION po not look into light or see the source of light directly FORWARD REVERSE AND TRIGGER LOCK LEVER NOTE Be sure the trigger is released when changing the position of the lever Always store the tool in the LOCKED OFF position Always check the direction of the Cordless Drill s rotation before use TO SELECT THE DIRECTIONS OF ROTA
42. linter Use spade bits when drilling large diameter holes in wood Use HSS drill bits when drilling in metal Use masonry bits when drilling in soft masonry Use a lubricant when drilling metals other than cast iron aluminum copper and brass When drilling start the hole slowly allowing the bit to drill deep enough to prevent slipping at higher speeds Never try to start a stalled Drill by clicking the trigger switch ON and OFF This may damage your tool To reduce jamming always keep the Drill running when pulling the bit out of a finished hole SCREWDRIVING Always use the correct type and size of screwdriver bit If screws are difficult to tighten try applying a small amount of washing liquid or soap as a lubricant Always hold the tool and screwdriver bit in a straight line with the screw MAINTENANCE AND CLEANING A WARNING Always remove the battery pack before attempting cleaning or maintenance NOTE This Cordless Drill is lubricated before it leaves the factory This lubrication should last for the life of the tool No further lubrication is required Use only mild soap and a damp cloth to clean the tool Never let any liquid get inside the casing Never immerse any part of the tool in a liquid Always keep the ventilation openings clear Always clean the battery pack using only a dry cloth Do not use liquids Always unplug the charger before cleaning it 17 Regularly clean the
43. mp environments or immersed in liquid Maintain labels and nameplates on the Cordless Drill These carry important information If unreadable or missing contact Alltrade for a replacement SYMBOLS IMPORTANT Some of the following symbols may be used on your tool Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the tool better and safer SYMBOL NAME EXPLANATION V Volts Voltage Potential A Amperes Current Hz Hertz Frequency Cycles per Second W Watt Power Kg Kilograms Weight No Alternating Current Type of Current Direct Current Type of Current T Alternating or Direct Current Type of Current Earthing Terminal Grounding Terminal n Class I Construction Denotes Double Insulation min Minutes Time S Seconds Time j Diameter Size of Drill Bits Grinding Wheels etc n No load speed No load Rotational Speed min Revolutions per Minute Revolutions Surface Speed Strokes etc per Minute 1 2 3 Ring Selector Settings Speed Torque or Position Settings FUNCTIONAL DESCRIPTION BATTERY A WARNING Before using battery pack please read carefully all instruc tions and cautionary markings on battery pack battery charger and product using battery Do not incinerate the battery pack even if it is severely damaged or is completely worn out The battery pack can explode Do not carry battery packs in aprons pockets or tool boxes product kit boxes drawers
44. om power source before attempting cleaning or maintenance NOTE This Impact Wrench is lubricated before it leaves the factory This lubrication should last for the life of the tool No further lubrication is required Use only mild soap and a damp cloth to clean the tool Never let any liquid get inside the casing Never immerse any part of the tool in a liquid Always keep the ventilation openings clear Brushes will wear with use and should be inspected periodically by qualified personnel Unscrew the plastic caps on the sides of the motor housings to inspect the spring and brush assembly If the brushes are worn down to the line closest to the spring replace them immediately Regularly clean the ventilation slots in your tool and charger using only a soft brush or dry cloth Never open the Impact Wrench case Do not attempt to repair the Impact Wrench yourself Opening this tool will void your warranty ACCESSORIES Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool Always attach grounded 3 prong extension cords to grounded 3 hole outlets If you must use an extension cord be sure that the gauge is large enough to carry the amount of current necessary for your power tool If not your tool may experi ence a loss of power excessive voltage drop or overheating The smaller the gauge number the heavie
45. ool and carries a HOME USE WARRANTY This tool is made for home use in the execution of projects and repairs in and around the home Use of the tool for COMMERCIAL PURPOSES OR ON A JOBSITE is not covered under this warranty The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession custody or control of the product whichever occurred first This warranty shall be null and void if the product or any component thereof is modified altered or used for any commercial purpose or on a jobsite This warranty does not apply to any other product and or component thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Alltrade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF Warranty Performance By purchasing the product purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and or part is promptly returned to Alltrade s facility postage pre paid and insured address ALLTRADE Warranty Claims amp Repair 1431 Via Plata Long Beach CA 90810 Attn Customer Service 310 590 3723 within the applicable warranty period with a
46. ould stick or slip To prevent wood from splitting drill pilot holes into the wood before driving in the screws DRILLING METAL WHEN DRILLING HARD METALS Apply a lubricant such as cutting oil to the tip of the bit e Start with a small hole then enlarge to the required size Make sure the bit is actually cutting and not spinning in the hole as this will dull the edges of the bit Keep enough pressure on the bit to keep it drilling through the material DRILLING MASONRY WHEN DRILLING M ASONRY Masonry can be brittle so be careful not to apply too much pressure and crack the material Apply enough pressure to keep the bit cutting and not spinning in the hole as this will dull the edges of the bit Bricks and similar soft materials will require less pressure concrete will require much more DRILLING WOOD Use twist bits to drill holes in wood Make sure the bits are sharp Pull the bits out of the hole frequently to clear chips from the flutes as an overburdened bit may overheat HINTS FOR OPTIMUM USE DRILLING Keep the right amount of pressure in a straight line with the drill bit Too little and the bit will spin without cutting too much and the motor may stall 16 Just before the drill tip breaks though the other side of the work piece drill more slowly and decrease pressure on the tool This will prevent stalling and leave a cleaner hole Use a block of wood to back up work pieces that may sp
47. r the cord see table below RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS TOOL CURRENT RATING CONDUCTOR SIZE IN A W G AMPERE 10FT 25FT 50FT 100FT 3 6 18 18 18 18 6 8 18 18 18 16 8 10 18 18 18 14 10 12 16 16 14 14 12 16 14 12 12 16 20 12 12 12 SPECIFICATIONS SPECIFICATIONS Voltage 120V N 60 Hz Rated Current 7 0A No Load Speed 2100 min Impacts Per Minute 2700 Maximum Torque 220 ft lbs OTHER CONSUMER DO IT YOURSELF DIY TOOLS Alltrade offers a full range of Kawasaki tools that make DIY jobs easy If you would like further information on the following products please contact Alltrade Customer Service Department at 1 800 590 3723 Cordless Drills Screwdrivers Reciprocating Saws Impact Wrenches Routers Sanders Rotary Tools Jigsaws Corded and Cordless Multi Purpose Tools Circular Saws Angle Grinders 3 YEAR LIMITED WARRANTY Express and Exclusive Limited Warranty to Original Retail Buyer Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying KAWASAKI tm power tool and no one else all parts of the product except those parts referred to below which are specifically excluded from such warranty see Exclusions to be free from defects in materials and workmanship for a period of three years from original date of purchase except that such warranty with regard to the battery shall be for a period of two years from original date of pu
48. rchase unless the tool is used for commercial or rental purposes SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE The above warranty for this Kawasaki tm power tool including the battery shall be effective for only 90 days from the original date of purchase if this tool is used for any COMMERCIAL OR RENTAL PURPOSE The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession custody or control of the product whichever occurred first This warranty shall be null and void if the product or any Wide Range of Accessories and more 11 component thereof is modified or altered This warranty does not apply to any other product and or component thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Alltrade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF Warranty Performance By purchasing the product purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and or part is promptly returned to Alltrade s facility postage pre paid and insured address ALLTRADE Warranty Claims amp Repair 1431 Via Plata Long B
49. rk To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles WARNING Handling the power cord on corded products may expose you to lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling WARNING Keep your work area clean and well lit Cluttered work benches and dark work areas may cause accidents or injury Do not operate power tools in explosive areas such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep bystanders children and visitors away while operating a power tool Distractions can cause you to lose control A WARNING Do not abuse the cord Never use the cord to carry the tool pulling or unplug ging the power tool Keep the cord away from heat oil sharp edges or mov ing parts Replace damaged cords immediately Damaged cords may create a fire Damaged or entangled cords increase the risk of electric shock A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery A charger that may be suitable for one type of battery may create a risk of fire when used with another battery Use battery operated tool only with specifically designated b
50. stractions can cause you to lose control ELECTRICAL SAFETY Do not abuse the cord Never use the cord to carry the tool Keep the cord away from heat oil sharp edges or moving parts Replace damaged cords immediately Damaged cords may create a fire PERSONAL SAFETY Stay alert watch what you are doing and use common sense when operating a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Remove adjusting keys or wrenches before turning the power tool ON A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times Proper footing and balance enables better control of the power tool in unexpected situations Use safety equipment Always wear eye protection Dust mask non skid safety shoes hard hat or hearing protection must be used for appropriate conditions TOOL USE AND CARE Use clamps or other practical ways to secure and support the workpiece to a stable platform Holding the work by hand or against your body is unstable and may lead to loss of control Do not force tool Us
51. this product Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paints Crystalline silica from bricks and cement and other masonry products and arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles WARNING Handling the power cord on this product may expose you to lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WORK AREA Keep your work area clean and well lit Cluttered benches and dark areas invite accidents Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep bystanders children and visitors away while operating a power tool Di
52. tteries of the type approved and supplied with this tool RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating maintaining and cleaning power tools Always use common sense and pay particular attention to all the DANGER WARNING CAUTION and NOTE statements of this manual A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury 4 CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage CAUTION NOTE provides additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood 4 WARNING Before using battery pack please read carefully all instruc tions and cautionary markings on battery pack battery charg er and product using battery NOTE Do not incinerat
53. uring the warranty period Alltrade will be responsi ble for the return shipping charges Alltrade s repair and or replacement of any non conforming item and or part thereof shall constitute fulfillment of all obligations to the purchaser Alltrade shall not be responsible or liable for any expense including freight charges or repairs made outside Alltrade s facility unless expressly agreed to by Alltrade in writing Under no circumstances shall Alltrade bear any responsibility for loss of the unit loss of time or rental inconvenience commercial loss or consequential damages Exclusions This warranty does not cover parts damaged due to normal wear abnormal conditions misapplication misuse abuse accidents operation at other than recommended pressures or temperatures improper storage or freight damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow recommended operating and maintenance procedures also voids warranty This limited warranty does not apply to accessory items such as drill bits screwdriving bits circular saw blades jigsaw blades grinding wheels sanding sheets and other related items DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUSE NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES COMMERCIAL AND RENTAL APPLICATIONS OR
54. written request by purchaser that Alltrade repair and or replace the nonconforming item and or part We recommend that you keep the original product packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit damage When sending your product include your name address phone number dated proof of purchase or copy and a statement about the nature of problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insured to Alltrade s facility see above address will be inspected and at Alltrade s option repaired and or replaced free of charge if found to be defective and subject to warranty Alltrade retains the sole discretion to determine whether any item or part is nonconforming and if so whether the item and or part will be repaired and or replaced If the unit is repaired new or reconditioned replacement parts may be used If Alltrade chooses to replace the product it may replace it with a new or reconditioned one of the same or comparable design The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period Typically a defective product that is returned within the first 30 days after the purchase date will be replaced for items returned after the first 30 days and within the warranty period covere
55. y by continuing to 8 Forward Reversing and 14 Double Ended Screwdriver Bits 2 pull on the tool trigger When tool performance begins to diminish stop the tool Trigger Lock Lever and recharge the battery for optimal performance Charge battery pack at ambient temperatures between 50 F 104 F COMPONENT MODEL NUMBER Store tool and battery pack in locations where temperatures will not exceed BATTERY PACK 691235 120 F This is important to prevent serious damage to the battery cells 120V AC ADAPTER 690074 The battery pack should always be recharged when the Cordless Drill begins to CHARGER 690072 run slowly 10mm 3 8 KEYLESS CHUCK 690076 When battery pack is not in use keep it away from other metal objects such as paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals 9 together may cause sparks burns or fire REMOVING ATTACHING BATTERY PACK REM OVE BATTERY PACK 1 Press both release buttons on either side of the Cordless Drill to release the battery pack 2 Pull battery pack free of Cordless Drill ATTACH BATTERY PACK 1 Align the raised portion of the battery pack with the groove in the battery compartment of the Cordless Drill 2 Press the battery pack into place Make sure the latches are securely fastened Do not use BUTTON the Cordless Drill if the battery pack is not seated properly CHARGER 4 WA
Download Pdf Manuals
Related Search