Home

Kathrein UFD 580S User's Manual

Contents

1. K1 Discovery Bayerisches F 17 43 Die Abendschau In the box at the bottom right of the screenshot above you see the day date and time of recording and the recording mode lf two recordings overlap the fact is indicated in the box at the bottom right Overlaps of series timer recordings are displayed in orange in the box at the bottom right see screenshot above and in the master list view bottom screenshot on previous page The programmed timer recordings will not be recorded the overlaps must be eliminated manually You can delete a programmed timer recording by pressing the red 0 button If it is a recurring series recording you are additionally asked whether you want to delete all the programmed recordings of this series in the example below Record every episode no more or merely the specific recording selected No recording on this day only Press ox to confirm or press ol to cancel Record every eplsode no more na TVTV EPG and Timer Important Additional Information If a satellite scan is carried out or programmes supported by the tvtv EPG are moved around the programme list the change is only visible in the twtw EPG following an update To update the receiver must be switched to standby mode tvtv appears on the display As soon as it disappears from the display the twtw EPG is updated The re button does not become active until 15 20 seconds after the picture appears on
2. KATHREIN TV freeze frame Controls Displays und Connections This section provides a brief description of all the controls displays and connections The button symbols presented here can also be found in the description of the operating steps View of front panel flap folded down 1 2 34 56 7 8 9 10 AC 98V 240V DIGITAL TWIN SATELLITE RECEIVER FE KATHA EITM UFD 580 20210024 Front Panel Controls and Displays Rear Panel Controls and Displays 1 On Off switch with mains disconnect 1 LNB 1 input and loop through output Menu button to call up or exit menus or 2 LNB 2 input and loop through output submenus Optical data stream output Remote control signal acknowledge SPDIF Sony Philips Digital Interchange Format for Dolby Digital AC 3 audio USB port for Service only Electrical SPDIF data stream output AC 3 audio Scart socket for VCR AUX connection Select button to confirm a selection Operation indicator O1 Standby indicator Arrow buttons for menu and programme list CON O O A O E ARON nen Biopsy te now Scart socket for TV connection programme slot and time Play and Record 6 7 8 Audio outputs L R cinch sockets 10 Pressure catch for front flap A ROMPE Open by lightly applying pressure on the 10 RS 232 port for Service only upper right hand side 9 Common interface for Pay TV cards 11 Mains power cable CA modules and Pay TV cards are not included Importan
3. These days DiSEqC components slaves must be reverse compatible i e respond to the analogue switching criteria from receivers that are only equipped with H V and 22 kHz control signals A DiSEqC switching matrix will work with analogue switching critiera until the DiSEqC command from the master is received All analogue switching criteria are then ignored DVB is the abbreviation for Digital Video Broadcasting DVB S refers to the transmission method S satellite MPEG is the abbreviation for Moving Picture Experts Group a working group that formulates internationally applicable standards for the digital compression of video and audio MPEG 2 has established itself as the standard for compression of digital TV signals MPEG 2 works up to a data rate of 100 MBit s The EB NO ratio is a measure of the signal to noise ratio of a digital signal The value is not identical to the C N value familiar from analogue reception technology At EB NO values below 5 dB no reception is normally possible FEC is the abbreviation for Forward Error Correction The FEC error rate corresponds to the Viterbi rate One Touch Recording The PID Packet IDentification number is an identification number for video signals and audio signals in the digital data stream of DVB MPEG 2 signals The receiver uses the PID number to create a unique assignment for the video and audio data transmission The 93 Short Technical Guide Programme packa
4. Antenna Setup nn ur I aliada i i Horizontal 18V Tuner LOOK 91 11 836 GHz 27 500 MSPS FEC 3 4 Motor Goto U a Las Move Save Set Limit My longitude My latitude UNIDAD UE P MENU Main EXIT Prey The first line is used to specify the satellite and the second line to specify the transponder The polarisation of the received signal and the transmitted symbol rate are shown on the next line The bars provide information about the strength relative level of the signal and its quality However this information cannot be used to draw any conclusions about the quality of the antenna system or the cable connection Antenna Rotor Positioner DiSEqC 1 2 For operation with a rotor DiSEqC 1 2 select On on the Motor Goto 0 line On the next line Move Save you can align the antenna to the east or to the west using the or gt button Press to confirm The optimum setup can be viewed in the Level bar chart On the Set Limit line you can press 3 or gt to specify the outermost aiming point limited by a wall or other obstruction in a westerly or easterly direction Always read the operating manual supplied by the rotor manufacturer thoroughly particularly with regard to settings different to those described above 75 Installation Menu Satellite Scan Pay attention to the bar at the bottom of the on screen display It provides guidance on what to
5. At present it is only possible to scroll forward from the Current Now playing views in the tvtw EPG in 15 minute blocks it is not yet possible to access days ahead by a quick and easy route To do so press the m button to access the Highlights view and use the arrow buttons to select the daily highlight tip displayed on the date you are looking for You can now press the button again to switch to the Current view and you will then see the data for the day you want 39 TVTV EPG and Timer Key to Symbols Symbol Explanation Widescreen format JS Programme broadcast in black and white T Dolby Digital 5 1 is a sound transmission method Er enabling digital surround sound to be reproduced on a home cinema system Dolby Surround gt Subtitles for the hard of hearin Stereo a a Two channel sound e g multiple languages available eo Daily highlight tips A A Ee e BO O MTTM 40 TVTV EPG and Timer Channel List The channels in the table below are provided with tvtv EPG data on Kathrein receivers as at February 10 2005 The assignment of the channels below to the tvtv EPG may change at any time hr television RTL shop ZDF documentary channel HSE24 RTL Television ZDF info chamnel Kabel 1 RTP Internac ZDF theatre channel SAT 1 EEE To obtain the EVEV EPG data for the SF1 SF2 and TRT International channels received over HOTBIRD 13 East in additio
6. Delete EXIT SaMMI Made 0 9 Edit HD Proaram Guide Play time Free 72 3 GRASA TNI 05 04 2005 08 55 Panoramah lder Bergwetter P OK Watoh Delete EXIT 3a tiite Mode 0 9 Edit Further control console functions are available during the recording To access them just press ue Use the arrow buttons to find the menu you want and select the following functions 47 Hard Disk Recorder Clear skip points Split take le nl gm E p Ri 00 00 77 000313 Stereo Panoramabilder Bergwetter e Lock Yes No Parental control On Off Playback is locked protected by password e Clear skip points No function during recording e Split take No function during recording The functions can be set with the arrow buttons Split Take You can split a recording at any point during playback Move the cursor bar to the Split take option using the y buttons and confirm with 0x The recording take is split and now appears twice in the hard disk programme guide with different running times Playback and Recording To switch to an already recorded programme without stopping the current recording you can use the OD buttons to place the coloured bar on one of the previous recordings in the HD Program Guide and select it for full screen playback by pressing 0x Play time Free 72 8 GRASZ BN 05 04 2005 09 04 mamtower P OK Watoh Delete EXID S E Made 0 7 D Edit The REC flag
7. Password section Under the System Information menu item you will find the factory settings which cannot be altered and are intended solely for service personnel Press em to return to the System Parameters submenu With the factory setting the receiver indicates the UTC Universal Time Coordinate previously Greenwich Mean Time transmitted with the data stream For Germany the time must therefore be corrected by 1 hour Setting System Parameters TV Type Aspect Ratio Screen AN Mode The summer time should be corrected as necessary in order for the timers to turn on and off at correct times You can correct the time yourself in 30 minute increments using the IL buttons To do this move the cursor bar to the Local time item using the y button Press twice to end your input The receiver saves the new setting When you subsequently switch the receiver off do so from the remote control not at the mains switch otherwise the settings will be lost Here you can use the o0 buttons to specify whether your TV set is a e PAL e multi standard or e NTSC set Press ler twice to confirm Here you can use the ON buttons to select the type of picture format for which your TV set is designed Either e 4 3 format or e 16 9 format or e Auto Press ler twice to confirm Here you can use the buttons to select the type of screen display e Conventional P S
8. Timer Recording Stopping a Recording Split Take Playback and Recording Fast Forward Fast Rewind no picture Playback Audio Mode Search Delete Audio Settings anne Setting the Volume Muting Stereo and Two Channel Sound Playback AC3 Programme List a Favourites Generating a Favourites List Alphabetical Channel Search Sorting Programmes Deleting Programmes Manually Adding Programmes Selecting the Last Programmes Received E A a ee E NE a nai Ga a ewe ere a AN GE ae re a a a a Factory Default Entering the Password Parental Control USING the Front Panel benik uas kawuk kaa Kana aaa ea Backup Operation Setting System Parameters 2 220202200002n00002n00nannnonnnnnnnnnnnnnnnnnnnnnnnn System Parameters Parental Control System Information Local Time Timer TV Type Aspect Ratio Screen AN Mode Adding Removing Satellites oooonnncccnnnncccconcncoccconoononancononcnronnananconnannnnnns Satellite Setup Entering a Satellite Name Removing Satellites Contents Installation MONU a nenne LNB Configuration Antenna Setup Antenna Rotor Positioner DiSEqC 1 2 Satellite Scan TP Edit Scan Important Note on Deleting Transponders DiISEqC UFO Setup UFO micro Factory Set Logging on to UFOmicro Video Recorder Connection 2 2 2 2 20 0 00nanananan an an an an nn ana nun an an un un an un nn ann nn Recording Playback Software and Programme List Update uu
9. place the time bar at the start of the last block of adverts and execute the split by navigating to the Split take command using the OD buttons and confirming with 0x S Clear skip points a Split take 9 Bayerisches F p 00 02 58 00 03 01 e Lock Yes No Parental control On Off Playback is locked protected by password e Clear skip points Clears all index marks Recording is split at the current position e g when recording two programmes one after the other The individual functions can be set with the arrow buttons 51 Hard Disk Recorder Time Shifted Playback Audio Mode Search Delete 92 Index marks can be cleared in pairs by running a scan to navigate to them and pressing the e button During a running recording you can call up and replay scenes from the running programme as it is being recorded see below or play the entire programme time shifted while it is still running by pressing the fast forward or rewind button See also Time shift The audio mode is set with the yellow button In our control console example stereo mode S is set Above it audio mode 2 Ch specific to the programme location is displayed and 5 1 Ch for Dolby All sound variants are recorded with the reception signal so you can then select them during playback yellow button See Playback section under Drive functions can be accessed with the following remote con
10. standard representation for 4 3 sets or e Letterbox display This setting enforces the widescreen format for a 16 9 set Press ex twice to confirm Here you can use the gt buttons to select the type of video signal at the Scart socket Select the signal that your TV set can process Refer to the operating instructions for your television set e Composite colour composite baseband signal e RGB Red Green Blue signal or e Y C S VHS signal luminance chrominance Press twice to confirm your selection 69 Adding Removing Satellites Satellite Setup New satellites can of course also be added to the LNB configuration To do this you must know the orbit position you need to aim at The Antenna Setup item on the installation menu can be used as an aid in aligning the antenna C a e o aaa ER Pay attention to the bar at the bottom of the on screen display It provides guidance on what to do next To access the LNB Configuration press ve for the main menu use the OD buttons to select the Installation submenu and confirm with also entering your password if activated Press OK to select LNB Configuration and you can enter or select a new satellite Note that your system must be configured accordingly In the next step use the OD buttons to move to the User1 entry for example After pressing the E or D button you are asked if you want to add the satellit
11. 15 More Episodes Wed06 04 20 00 Thu 07 04 20 00 Fri 08 04 20 00 Sat 09 04 2000 Sun 10 04 19 54 Mon11 04 20 00 You can use the 96 buttons to switch to the details on the next programme in the selected view Press to return to the previous display such as the programme list You can programme a recording from the various views of the tvtv EPG Current Program list Highlights and Det information Details and from within their various submenus Programming is pre configured for two SAT IF input signals If you are operating the receiver in Loop mode LNB 1 Loop out output on LNB 2 in input this may cause problems when two programmes are recorded at once if both programmes are not transmitted on the same transponder Use the arrow buttons ADO to select the programme you want and press the red 0 button The following display appears example Tuesday 05 04 2005 9 08 31 Search e Tue 05 04 DSF Handball 1 Bundesliga Recording once 19 45 21 46 OK Plan recording 35 TVTV EPG and Timer You now have a number of options to programme your recording The settings are made using the arrow buttons ADO and the number pad When recording to hard disk the e Recording status once daily weekly user defined series signal is not forwarded to the lt VCR Scart socket selected using the buttons When recording on a VCR or e Date ad
12. AU buttons To access the submenus press ox The items in the submenus are selected by pressing the My buttons The settings under the various options are made either by pressing the CO buttons or using the number pad Quit the main menu or submenus by pressing en You use the number pad buttons to enter programme and satellite names The numbers and letters appear in the name fields of the corresponding menus Place the cursor in the name field The first character is automatically given a dark background You can now use the number pad to enter letters by pressing the relevant button several times For example the 2 is also used for A B and C 11 Operating Instructions Alphanumeric Assignment of Remote Control Number Buttons O W UNUSED UNUSED Language Selection OSD The language for the on screen display is set as_ follows eu gt AU gt Menu language gt CO gt English gt D The languages available are Dutch English French German Italian Portuguese Spanish and Turkish Connection and Setup Connecting the Unit Sat IF Connection Reception Requirements Reception System Presets The following section is intended specifically for specialist dealers You only need to pay attention to this section if you are carrying out the installation yourself The Connection Examples section provides a range of sample configurations Do n
13. DVB data stream On screen display OSD in 8 languages Dutch English French German Italian Portuguese Spanish Turkish 4 character LED display DiISEqC 1 2 and tone burst control signal Operation with UFO mini and UFO micro RS 232 port for data copying Programme scan and sort functions Automatic aspect ratio recognition optional 4 3 or 16 9 picture format Volume adjustment and muting Radio button Infrared remote control 2 Scart sockets TV and VCR AUX connection Additional audio outputs via cinch sockets Electrical and optical output for Dolby Digital data stream output AC 3 RF level indicator 87 Technical Appendix Technical Data RF Properties Tuner 1 and 2 Video Audio Memory Common Interface Hard Disk Recorder Power supply 88 Sat IF frequency range Input level range IF frequency Reception threshold EB NO dig Sat IF input Input impedance Modulation FEC demultiplexer Video resolution Frequency range Input data rates Video decoding Bit rate Output voltage S N Audio decoding Bit rate Frequency range Output voltage S N Flash RAM SD RAM 2 slots Capacity Recording time Mains voltage Power supply Power consumption in standby LNB supply voltage LNB supply current Control signals 2 x 950 to 2150 MHz 43 to 83 dBuV 479 5 MHz gt 4 8 dB 2x F socket with loop through output 75 Q DVB S standard CCIR 601 720 x 576 lines 20 Hz t
14. If the search is unsuccessful the following message appears Error All new programmes are added to the existing programme list The TP Delete option allows you to remove the transponder from the programme memory by pressing 0x You are asked to confirm before it is deleted Important Note on Deleting Transponders The following transponder must not be deleted as the tvtv EPG data is transmitted on it ASTRA 12 603 75 MHz symbol rate 22MSymb s horizontal 79 Installation Menu DISEGCTM UFO Setup Pay attention to the bar at the bottom of the on screen display It provides guidance on what to do next 22 kHz Signal A 4 DISEqELUFOI Setup Tone Burst DiSEqC DiSEqC Repeat UFO mini Remote Frequency UFO micro I II P MENU Main EXIT Prey You should only make changes in this menu if the receiver is connected to a different reception system with different properties or if changes have been made to the reception system You should therefore carefully follow the instructions for your Sat IF system However before each change you should note the settings on the form at the end of this operating manual Press eu OD and ok to access the DiISEqC menu This menu option is used to specify whether the 22 kHz signal is to be used to switch between the upper and lower frequency ranges for a satellite low high or between two satellite positions T
15. Interface for insertion of two so called Conditional Access modules is located underneath the front flap The Smartcard sold by the Pay TV provider specific to a particular encryption technology is inserted into the CA module The card is not included in the receiver package The cards and modules are issued by the respective Pay TV providers and contain the subscriber data and details of the programmes for which the subscriber has paid These programmes are always encrypted Contact the Pay TV provider if you are interested in subscribing to a particular Pay TV channel You alone are responsible for use of the cards Keep the card and the associated PIN code in a safe placing when not in use When you turn on the receiver the following message appears k p gti gt L Astra 31 3sat 1421 Herrscher emer versunk 14 00 15 40 um V2 OELE 15 40 15 45 A CA module must be inserted for the message to appear however You can find out which card is inserted in the Common Access module by selecting Common Interface from the main menu and confirming by pressing ox The screenshots below depend on the specific module and card and so are only intended as examples Common Interface OK Next MENU EXID Prev Press 0k to access a menu generated by the module 29 Common Interface From this menu your card and your PIN code allow you to access various programmes from
16. any changes in the DiSEqC UFO setup refer to the DiSEqC UFO Setup section When you are in the LNB Configuration menu see above press the OD buttons to move the coloured bar to the HOTBIRD item Press the a or gt button and to confirm that you want to add a satellite The transponder data is now stored and a tick appears after HOTBIRD to confirm the setting You can now set the DiSEqC TM signal lt is used to switch between the two aligned satellites Press OD to access the DiSEqC 1 setup Set 1 for ASTRA and 2 for HOTBIRD Both positions are pre programmed Press em four times to exit the menu This saves the set value If you make an incorrect setting you will see the following message Weak signal or no signal With cascaded switches a total of 16 satellite positions can be stored under DiSEqC M2 H V and High Low give a total of 256 possible settings These settings and the configuration of a system of this kind should be left to a specialist Tuner Select Here you select whether both tuners IF input are connected to the antenna system or only one of them In the Loop setting the reception signal is looped through to the outputs in order to make it available for other Sat receivers 74 Installation Menu Antenna Setup This menu is exclusively intended for service purposes and be used to align the antenna in an emergency if no measuring instruments are available
17. be repeated In this case set the DiSEqC Repeat menu option to 1 or 2 Default setting Off UFO mini In a subscriber controlled processing system the input frequency of the receiver is a fixed setting The subscriber controlled processing system transmits the signals at this frequency The reception parameters for programme selection are communicated to the reception system by a DISEqCT command and set The setting that has to be selected depends on the design of the subscriber controlled processing system The setting is made according to the installation instructions for the subscriber controlled processing system Remote Frequency If you have set the UFO mini menu option to ON use this menu option to make the setting from the transmission frequency The transmission frequency to be set is specified in the installation manual for the subscriber controlled processing system You should therefore be sure to follow the instructions given in the installation manual for the subscriber controlled processing system 81 Installation Menu UFO micro Factory Set Logging on to UFOmicro Important The receiver must not be connected to the antenna socket outlet prior to logging on 82 The setting for this menu option is also designed for operation of the receiver in a processing system The return path of the coaxial cable is used for control and communication between the
18. buttons select All satellites Press to access the current channel list Alphabetical Channel Search Pay attention to the bar at the bottom of the on screen display It provides guidance on what to do next 96 e AN Ae You see an alphabetical listing of programmes This makes it possible to locate a specific programme from the full programme list very rapidly Programme List Press 0x to access the channel list Press m to launch Channel List Mode Use the OD buttons to select the Alphabet line Use the J gt buttons to scan the alphabet for the first letter of the entry you are looking for Ar MAMA All Satellites I Press ok to confirm the selected letter and a list of all the programmes beginning with the letter appears Use the OD buttons to choose your channel which is then highlighted by a coloured bar The channel preview appears in the top right hand corner of the screen Press to confirm your selection The programme appears on the screen To return to the channel list listing all the programmes from the configured satellites press the button and then press for Channel List Mode First use the OD buttons to select the Satellite line and with the buttons select All satellites Press to access the current channel list 57 Programme List Sorting Programmes Pay attention to the bar at the bottom of the on screen dis
19. do next 76 Satellite Scan Satellite Name D OK Select MENU Main EXIT p In the Satellite Scan menu you set the receiver searching for programmes on a Satellite Move to the menu line you want using the OD buttons On the first line press or gt to select whether to scan for only FTA or FTA and encrypted scrambled programmes You can also set one of the registered programme providers e g PREMIERE Press or gt to set the satellite you want Then press to start the scan Satellite Scan gt a JAAN AAN AAN If you want to change your system to a completely new satellite you will need to manually enter at least one known transponder in order to start the scan see TP Edit Scan You can obtain the necessary information from the relevant TV and satellite magazines or Internet websites During scanning the signal quality the scanning progress and the new programmes found are displayed Installation Menu TP Edit Scan Pay attention to the bar at the bottom of the on screen display It provides guidance on what to do next At the end of the scan this message appears All new programmes are added to the existing programme list and highlighted in a different colour You can interrupt the scan by pressing the button In this menu you can scan through the transponders for specific programmes when for example new programmes are offered in the Installation LNB Co
20. maintower lt A Y OK Watoh Delete EXIT Sa x Edit a x A a Pr uu oo With the OD buttons you can select a currently running or previous recording and start the playback by pressing 0x The recorder plays the recording you selected h appears on the LED display 49 Hard Disk Recorder 50 The asterisks stand for the recording number At the end of the playback the receiver switches back to the HD programme guide lf you are recording at the time the display remains REC 1 or REC 2 9 Bayerisches F 4 00 45 00 03 01 Tele Gym Drive functions can be accessed with the following remote control buttons Visible time controlled rewind Visible time controlled fast forward Normal playback 0000 Freeze frame with or gt freeze frame or picture by picture only if control console is not displayed if control console is displayed advances 10 seconds at a time unlock with m Hard disk programme guide is displayed playback is stopped with playback is resumed 0 4 speed slow motion during playback red button The symbol for the current function is displayed in the bottom left hand corner of the screen During playback you can get all necessary information by pressing the ok button At the top left of the bar the programme being played back is indicated To the right of it a progress bar indicates how much of it has been play
21. must be earthed as specified or equipotentially bonded EN 6072811 and any national regulations must be complied with Danger due to surge voltages lightning sinkes Mains voltage Only operate the unit with the spectied mans voltage marked on the rear of ihe unft or on the extemal power pack The uni may only be connected to the mains and iurned on once it has been connected to the antenna and to the TW set or the cable network and PC if the mains voltage is too high here is a nsk of fire Repairs Ensure that any repairs to your unit are carried out by qualified personnel Opening tee unit and attempting to repair it yourself voids all warranty claims Improper work on the unit can jeopardise the electrical safety of the unit The manufacturer accepts no liability for accidents caused by the user opening the unit Connections Incorrect wiring of the connections can lead to malfunctions or defects on the unit Long periods of absence storms Always turn off the und at the mains swich if you will be absent for a long tme or there is a storm If your unit does not have a mains switch you can disconnect A from the mains by unplugging the mains connector The also apples to the other equipment connected to the unit Isolation from the cable network is also recommended Note any tener programs receiver and turn the unit on again promptly before the recording time Installation location Alleectrons equipment generates heat However th
22. pressing the button and automatically displays the Current Now showing view see Current menu item regardless of which twtw EPG view you had been in beforehand Current View The tvtv EPG automatically displays the Current Now showing view when first accessed highlighting the current selected channel and the current programme Tuesday 05 04 2005 08 23 Hr fernsehen Landesschau Baden W rttemberg SR Fernsehen Tagesschau vor 20 Jahren SUDWEST BW Tagesschau vor 20 Jahren WDR K ln Planet Wissen BR alpha Reports In English Arte Sendeschluss In the main window you see the channel number at the left the channel name and current programme in the centre and a progress bar at the right In the top right hand corner of the picture you see the current day date and time The box at the right indicates the day date and duration of the programme the programme category in the example Series the programme s country of origin and the year it was made The bottom section of the display contains the tvtv EPG options selectable from any EPG view Press a red to view the recording schedule Timer list green to view the Current Now showing display yellow to view the Programme list of the selected channel m blue to view the daily highlight tips one tip per day a week ahead x to view details of the selected programme and 0 red to acce
23. receiver and the Kathrein UFO micro system If the receiver is operated in a UFO micro reception system the UFO micro menu option must be set to On The reception system then assigns the receiver a special address upon installation so that it will recognise the control commands sent by the receiver to the reception system for signal selection In this operating mode a remote frequency does not need to be set as it is specified by the UFO micro system with the addressing If the receiver is being used in a UFO micro reception system for the first time the address previously assigned must be deleted This is done under the UFO micro menu option by selecting Reset with the G buttons and confirming with ox The receiver is then assigned the original factory setting It then needs to be set to On again The receiver receives its new address from the new system Reset does not delete the pre programming Default setting Off Under this menu item you can reset all the settings to their factory defaults by pressing ex The factory settings do not necessarily correspond to the settings required for your specific system You may need to re enter all the settings following the reset Note down the settings on the service page provided at the end of this manual Procedure see page 10 Recording Playback Note For details of how to connect your video recorder to the r
24. to the right of the programme title indicates that this programme is being recorded 48 Hard Disk Recorder While you are watching a pre recorded programme the previously selected programme continues to be recorded For capacity reasons only 400 single recordings are possible on the 80 GB hard disk When started by EPG the recording time automatically stops five minutes after the end of the programme titles see page 44 Without EPG the recording time is automatically pre programmed at two hours Changes can be made using the JE or by entering numbers If the hard disk is full recording stops Fast Forward Fast Rewind no picture To forward or rewind the receiver rapidly without viewing the picture in playback mode e Press ox during playback of the recorded programme to access the control console and press the pause button Il e You can then press O rewind or gt fast forward to rewind or fast forward with no picture the longer you hold down the button the faster the speed becomes e Use the gt and arrow buttons to jump to the end or back to the start of the recording Playback To play a recording from the hard disk press the 0 button The HD Program Guide appears with a list of the recordings saved to the hard disk If there are no recordings stored on the hard disk a message is shown telling you so HD Program Guide ITA Play time Free 72 7 ATA 05 04 2005 09 04
25. your Pay TV provider Main menu 2 Available entitlements 3 Smart card management CryptoWorks has been selected as an example here The details may vary for each CA module The displays appear in English even if you have selected German as the menu language for the receiver Please always follow the instructions supplied by your Pay TV provider Information for Conax SECA Viaccess and CryptoWorks users Note that with monthly activation intervals the programme providers have different procedures for activating Pay TV cards Activation may therefore be a few days before or after the beginning of a new month During this activation period the CA module and card must be in the slot and the receiver must be turned on a set to the booked Pay TV channel Follow the instructions from the Pay TV provider For monthly subscription extensions the card can be re initialised by way of the CAM CAM Re initialisation menu lf your Pay TV card is then still not enabled we recommend you briefly withdraw the CA module with the card out of the slot with the receiver switched on and then re insert it This information has nothing to do with the properties of the unit it is merely intended to assist you 26 Twin Functions Picture in Picture PIP The UFD 580 is equipped with two tuners enabling you to perform two separate functions at the same time including e Picture in picture PIP e Time shift
26. z2u0020 n000nnnnnnnnnnnnnnnn nn Receiver to Receiver Data Transfer 2 u24242 020 0000 nnnn ann nn ann nn nn nun nn nn Preparations Programme List Download Operating System Software Download Technical ADDENGIN Pr oe o en Technical Features Technical Data Connections Accessories Scart Socket Assignment VHS S VHS Switching Connection Example TEOUDIESNOOLNG ut aid Short Technical Guide 2 1 nn accio ais SOU O A a O O aa Aa nn O O ee Safety Instructions Important Information DANGER WARNING A CAUTION This page contains important information about the operation instalation location and connection of the ww Read these instructions carefully before starting do use ihe unt Mains cable Make sure that the mains cable power supply cable is mot damaged Units with a damaged mains cable must be disconnected from the mains disconnect mains connector and repaired by a 0us fed engineer before setup Only use the power pack supplied if available Risk of death due to electric shock Cleaning Disconnect the mains connector before cleaning the una Only use a dry cloth for cleaning and only clean the outer surface Mever open the unit Touching the parts inside the unit cames a risk of death due lo electric shock Playing children Make sure that children do not push any objects into the ventilation slots Risk of death due to electric shock Earth connection The antenna sysiem
27. NU EXIT Exit _ Y i Press the button to activate the input mode The first letter is highlighted You can now rename the Favourites list as you wish using the number pad buttons and the gt buttons Press OD to move to the other Favourites lists and change their names likewise Favorite 5 When you have completed the input by entering all the letters confirm it by pressing E You are returned to the channel list Press again to return to the TV screen You will see a message confirming that your changes have been saved and the info display for the current programme being received will appear on the screen for a few seconds To call up a favourite programme access the channel list press the Q button select the desired Favourites list using the JP buttons and press Ok to confirm 55 Programme List Then use the OD buttons to select your desired programme which is highlighted by a coloured bar and displayed in the top right hand corner of the screen Press OK to view your selected favourite programme To delete a marking press to select the Favourites list containing the programme you want to unmark and clear the apple symbol by pressing the red m button To return to the channel list listing all the programmes from the configured satellites press the button and then press m for Channel List Mode First use the OD buttons to select the Satellite line and with the
28. Operating Manual Twin DVR Sat Receiver UFD 580 9805 with Hard Disk Drive KATHREIN Antennen Electronic Preface Important Information Dear customer This Operating Manual is intended to help you make the fullest use of the extensive range of functions offered by your new satellite receiver We have tried to make the operating instructions as easy as possible to understand and to keep them as concise as possible To help you understand particular specialist terms that cannot be translated we have added a short glossary at the end of the manual The power switch is an environmentally friendly feature If you will not be using your receiver for a longer period you should therefore use the power switch to disconnect it from the power supply to save energy For shorter breaks you can switch the receiver to standby on the remote control which uses only a minimal amount of energy We wish you good reception and much pleasure using your new DVR Sat receiver Your KATHREIN Team If you should experience any unexpected problems with your receiver please contact your specialist dealer or our hotline Tel 49 8031 184 700 Fax 49 8031 184 676 The programmes available on the satellites and transponders are subject to continual change In such cases it is necessary to reset the channels as the factory preset programming corresponds to the situation on the date of manufacture The information for this reset can be fou
29. V EPG and Timer Highlights Press the blue m button in the tvtw EPG to view the daily highlight tips The following display appears example Tuesday 05 04 2005 9 08 25 Cam E Highlights E y Tue TELE 5 20 15 22 06 x Q Hasse deinen N chsten TELE 5 20 16 21 40 Auf der Suche nach Jimmy Hoyt RTL Televisio 20 16 22 15 Die unl sbaren F lle des Herrn Sand RTL2 20 16 21 10 Stop Oder meine Mami schle t ZDF 20 16 21 46 Einsatz in Hamburg Das Erste 20 15 21 45 K3 Kripo Hamburg ZDF 20 15 21 45 Prinz und Paparazzi A tip is shown for each day up to a week ahead Programmes Sorted by Category You can use the 96 buttons to view the following programmes on the Highlights menu by category e g Series Sport New Magazine Reportage Kids Within each category you can scroll line by line or page by page as usual using the arrow buttons OOD Press the red 0 button to place your selected programme in the Record menu see Record f Tuesday 05 04 2005 0825 ner E Program for kids Be Tue KiKa a Q Sesamstra e Tue Super RTL Rubbadubbers 47 Tue KiKa 08 30 08 40 Mini Robos 20 Tue Super RTL 08 30 09 00 Blue s Clues Blau und schlau 30 Tue KiKa 08 40 08 45 Musik Boxx Tue KiKa 08 45 09 00 Albert auf Entdeckungstour 8 Tue KiKa 09 00 Teletubbies 32 Search Function The Search function of the tvtv EPG allows you to
30. and e One touch recording The picture in picture function permits simultaneous viewing of two programmes This allows you to see when a programme you want to watch begins without having to leave the programme you are currently watching When you press the green D button the first time a window opens up in the top right hand corner The channel is indicated underneath the picture You can then change programme in the malin picture with the buttons The programme displayed in the PIP window can be changed with the OD buttons Press the OS buttons to swap the main picture and PIP programmes 27 Press the green button a second time to view a picture played back from the hard disk in the PIP window e A picture currently being recorded is framed in red e A previously recorded picture is framed in yellow H 2 BR alpha The picture caption is prefixed by an H for hard disk and the serial number PIP Press the green P button again or the button to exit the PIP function Time Shift The time shift function is described in the Hard Disk Recorder section Note that the receiver switches to hard disk mode when executing this function One Touch Recording One touch recording is described in the Hard Disk Recorder section Note that the receiver remains in TV mode when executing this function 28 The tvtv EPG is a latest generation Electronic Programme Guide replacing the existing EPG and t
31. ar at the bottom of the on screen display It provides guidance on what to do next Oscillator Frequency L O 12 You should not change the following settings without a good reason as they are factory settings or operating settings that are tailored to your reception system New settings are only required if the reception system is changed or expanded Select the Installation menu with the f button the N buttons in the main menu and ox If a password has been stored you must enter it Use the OD buttons to select the further items US 5 LNB Configuration A Astra p e w EutelSat 10 y EutelSat 16 v TurkSat 42E v Telecom 5W w Telecom 8W v ASTRA28 y P5 P Page Up On OK cgit A ER ng a u 7 The first submenu is the LNB Configuration Press ok to open it You should not normally make any changes in this submenu Before making any changes however you should make a note of the settings in the form provided at the end of this manual Your receiver is preset at the factory to the satellites of the ASTRA and HOTBIRD systems The other basic settings are shown in the screenshot above Satellite reception systems consist of a parabolic antenna attached to the actual reception system LNB Low Noise Blockconverter or LNC Low Noise Converter which converts the RF signal from the satellite into a lower frequency that can be processed by a satellite receiver The satellit
32. arious views of the tvtv EPG however When you press x the following display appears example Tuesday 05 04 2005 08 29 ep Pa E Search Tue 05 04 DSF 19 45 21 45 Handball 1 Bundesliga o Live event Sport Handball Am 26 Spieltag der Handball Bundesliga muss der Deutsche Meister und Supercup Gewinner von 2003 TBV Lemgo ausw rts gegen die HSG Wetzlar antreten Das Aufeinandertreffen der beiden Teams findet zum ersten Mal in der neu er ffneten Nittelhessen Arena statt die ein stolzes Fassungsverm gen von 5000 Zuschauern aufweist Im Hinspiel in Lemgo wurde Wetzlar regelrecht aus der Halle geschossen Use the 10 buttons to switch pages in the programme details The third page displays the upcoming episodes f Tuesday 05 04 2005 9 08 30 Car Ga Search y Tue 05 04 DSF 19 46 21 45 Handball 1 Bundesliga Live event Duration 120 Min Original title Actors Director FSK 34 TVTV EPG and Timer Programming a Recording If no EPG data is available for the channel you selected In the Current view select the channel for which you want to programme a recording and press the red e button As there is no EPG data you must enter the data date start end manually Use the arrow buttons AMBOS and number buttons to make your input Press ox to save your settings Tuesday 05 04 2005 08 30 Search o i Tue 05 04 Sport 20 00 20
33. cal Guide Personal Identification Number See Short Technical Guide Satellite receiver Video signal made up of three individual colour signals red green blue Receiver input signal 21 pin connecting cable e g receiver TV Card from Pay TV provider to encrypt its programmes Standby mode Super Video Home System video recorder standard Rate of data transmission of satellite signal Time shifted playback Clock function for pre programmed switch on and off times See Short Technical Guide Kathrein specific satellite signal processing systems Video recorder connection See Short Technical Guide 95 Service OSD OSD language Aspectratio ratio LNB LNBmode Tuner input O German O OQ 16 9 Satellite 1 Satellite 2 O O 9750 O 10600 Satellite Satellite LO1 O 9750 LO1 LO2 O 10600 LO1 Satellite Satellite 96 DiSEqC menu 22 kHz O Tone Burst O DiSEqC O DiSEqC Repeat O UFO mini O Remote Frequency __ MHz UFO micro O ON Additional settings High Low High Low ON ON ON O O O O OFF ON OFF PosA B PosA B OFF OFF OFF O 1 C 2 O 1 amp 2 O Loop Satellite 3 Satellite LO1 O 9750 LO1 O 10600 Satellite O OFF O OptA B OFF 97 98 99 936 2576 B 0605 ZWT Technical data subject to change Internet www kathrein de KATHREIN Werke KG phone 49 8031 184 0 Fax 49 8031 184 306 Anton Kathre
34. can also check the recording status without having to interrupt the recording The stop time is indicated at the right of the top bar Press to return to the full screen without stopping recording Press to view the hard disk contents If you press the 4 button at this stage of recording a second time Shifted recording is started You can stop that recording by pressing E and a or by pressing a You can stop recording by pressing and You can then delete the programmed recording by pressing m and ox 45 Hard Disk Recorder Timer Recording Stopping a Recording If two recordings are running at the same time the PIP function is not possible 46 If you want to immediately lock in a running recording all you have to do is select the hard disk contents with the button select the relevant recording from two possibilities with the OD buttons and then confirm with the ox button For information about recording by means of a timer please refer to the Programming a Recording section under TVTV EPG The timer begins recording at the pre programmed time All hard disk functions are active during the timer recording This means playback can be started in time shift mode even when recording has already begun The recording can only be stopped with the standby button or the button the HD programme guide menu appears or by pressing and the suggested button After t
35. correct PID entries are rejected Press ok to acccess the channel list You will see a message confirming that your changes have been saved and the info display for the current programme being viewed will appear on the screen for a few seconds The new programme is added to the existing channel list You can obtain the necessary PIDs from relevant magazines or the Internet as well as from the SAT 1 Videotext Teletext service Refer to Operating Instructions section for information on how to make alphanumeric entries Never change the PID information without good reason as they affect identification of the reception signal This function is only necessary for programmes which are not broadcast according to the DVB standard All programmes that comply with the standard are recognised and saved by the automatic search Selecting the Last Programmes Received 25 Emstestival 30 ZDFiheaterkan 25 ZDfrdokukanal By pressing the red button the last four programmes received that were selected for at least 10 seconds are displayed on the screen The arrows shown correspond to the arrow buttons CONO These buttons can then be used to select the relevant programme 61 Password Factory Default Entering the Password Pay attention to the bar at the bottom of the on screen display It provides guidance on what to do next 62 You can use a password to lock your satellite receiver against unauthoris
36. d the optical output are for connection to a Dolby digital system see Connection example Inserting Batteries in the Remote Control E E Remove the cover on the rear of the remote control Insert the two supplied batteries into the remote control Ensure correct polarity of the batteries the and markings are indicated inside the battery compartment Slide the cover back into the housing until it locks in place Used batteries are special waste Do not throw used batteries into your household waste take them to a collection point for old batteries Electronic equipment is not household waste in accordance with directive 2002 96 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL dated 27 January 2003 on used electrical and electronic equipment it must be disposed of properly At the end of its service life take this unit for disposal at a designated public collection point 15 Initial Setup Getting Started Power Failure Safety Error Signalling 16 Connect the unit to the mains power supply Switch on the receiver by pressing the power button on the front of the unit The LED shows The operation indicator LED lights up red the unit is in standby Switch on the receiver by pressing the button on the remote control The red LED on the front panel of the receiver flashes each time a button on the remote control is pressed The screen displays the factory preset
37. e Note In two cable systems the tuner input must be set to 1 amp 2 The DiSEqC settings must match the installed reception system In single cable reception select the tuner input used Set Loop when the output of tuner 1 is connected to tuner input 2 or vice versa Gr Confirm with 01 The following message appears 70 Adding Removing Satellites You can now make the entries in the relevant items according to your reception system using the OUNO buttons Press Pm three times to exit the menu The new transponder data is saved Entering a Satellite Name You can change the satellite name in the LNB Configuration menu using the number pad buttons For information on how to do this refer to the Operating Instructions section Removing Satellites To remove a satellite open the main menu by pressing eu select Installation with 0 select LNB Configuration with ox and use the OD buttons to move the cursor bar onto the satellite you want to remove After pressing you are asked if you want to remove the satellite and can confirm or decline the prompt LNB Configuration Ka LOW L U Power DISEaC 1 4 DISEaC 2 E Pay attention to the bar at the bottom of IF INPUTS the on screen display It provides guidance P gt Page Up On OK Edit on what to do next PE 71 Installation Menu LNB Configuration Pay attention to the b
38. e You can hide the control console by pressing E You can also view a current programme To do this stop playback by pressing the button and quit hard disk mode with the button You will be asked if you want to stop the recording Press again to switch to TV mode without interrupting the recording Hard Disk Recorder One Touch Recording OTR You can record an encrypted programme even ifno CAM or Smartcard is inserted Note Note With your twin DVR Sat receiver you can immediately record the current programme to the hard disk at the press of a button All you need to do is press the red e button During recording the red standby LED on the front panel of the receiver flashes and R or 2 x R if two recordings are being made flashes in the top left hand corner of the screen for a few seconds If you want to start recording within the first five minutes of the programme you will need to press the red 2 button again and check that the end stop time is correct If required you can enter the stop time in half hour increments using the gt buttons or directly using the number pad Press to save the change Recording is automatically stopped after switching EPG or after two hours at the latest You can still select all other programmes If you press the button you will see the recording status and can stop the recording process see below Using the screenshot above you
39. e and view one of the programmes from different transponders in one polarisation plane Record two programmes and view one of the programmes from two transponders in two polarisation planes Record two programmes and view one of the programmes from two transponders and in two polarisation planes Simultaneous playback of a recording To proceed correctly For 1 tuner 1 must be connected to the antenna system This applies for example to a satellite dish with a single LNB or a single cable system For 2 tuner 2 must be connected to the antenna system This applies for example to a satellite dish with a single LNB or a single cable system For 1 amp 2 connect each single input to a port of a two cable system 42 Hard Disk Recorder You can allocate one or more satellites to each tuner provided you have a DISEqC system In the Loop setting you must connect one tuner output to the input of the other The setting you select for tuner input will depend on your reception system In case of doubt consult your specialist dealer so that you can use your receiver optimally Recording Your receiver also enables you to record encrypted programmes with or without a CAM and Smartcard For playback the CAM and Smartcard must be inserted Encrypted recordings are identified by a sign in the hard disk contents In order to convert an encrypted recording into an unencrypted rec
40. e correct for your system In case of doubt consult a specialist engineer Initial Setup Receiver Presetting Your receiver is factory pre programmed to receive the ASTRA 19 East 28 East and HotBird satellites as well as Eutelsat 10E and 16E TurkSat 42E Telecom 5W and 8W and others You do not normally need to make any additional settings If you are not connected to a communal system you will need a multifeed arrangement with at least two LNBs in front of the satellite dish in order to receive multiple satellite systems Consult your specialist dealer on this Before you change the basic settings of your receiver write down the settings on the form provided at the end of this operating manual You will then be able to restore the original settings at any time 17 On Screen Display OSD Important On Screen Displays Help Function Pay attention to the bar at the bottom of the on screen display lt provides guidance on what to do next 18 The receiver functions are controlled by a microprocessor and comprehensive software The following explanations are intended to improve your understanding of all procedures and to minimise the risk of mistakes You can call up help for each menu or menu function This help function provides you with a brief description of the most important functions of the selected menu options For example access the main menu by pressing eu Main Menu System Para
41. e heating of this unit bes within the permessi range Sensitve furniture surfaces and veneers may become dsooloured by the effects of constant heat over time The feet of the unit can aso cause colour changes to treated furniture surfaces If necessary place the unit on a suitable stable and flat base Ventilation The heat generated in this unit is adequately dissipated However the unit should never be mata ed in a cupboard or on shelves with inadequate ventilation Never cover the cooling slots on the unit e g with other eouspenent magazines tablecloths or curtains Do not place any objects on top of the uni and mantan a clearance of at least 10 cm above the unit so that the heat generated can be dissipated with mo obstructions Moisture sunlight heat Protect the unit against moisture dnpping and splashed water do not place any fed objects such as vases on top of the unit Do not place the uni close to a heater or expose it to direct sunlight and do not operate it in damp locations Only use the unit in a moderate climate not in tropical conditions Receiver Features Remote control RC 660 The UFD 580 has two separate tuners for simultaneous reception of two programmes and a hard disk for recording and playback Depending on constellation you can view one programme and record another to hard disk play back one programme from the hard disk and record one programme to hard disk or record two programmes to hard dis
42. e provider s programme package The terms digital transponder and programme package have the same meaning The video bit rate describes the quantity of data from the digitised video signal that is transmitted per second The Viterbi rate code rate error rate characterises the error protection used by the programme provider The DVB standard provides the following values 1 2 2 3 3 4 5 6 7 8 AC 3 Audio output AV programme slot CA Cl Decoder DiSEqC DVB EB NO dB EB NO ratio LED display LNB Mute OSD PAL Pay TV PCMCIA PID PIN PIP Receiver RGB Satellite IF signal Scart cable Smartcard Standby S VHS Symbol rate Time shift function Timer function Transponder UFO micro and UFO mini VCR connection Viterbi rate Short Technical Guide Output for Dolby Digital signal Sound output on the receiver Preferred programme slot on TV set for Scart input Conditional Access for decoding of encrypted programmes Internationally standardised interface for CA modules Encryption device for Pay TV Control system between receiver and LNB multi switch Digital Video Broadcasting Power density per unit of information Digital signal to noise ratio Display on receiver Low Noise Block Converter Muting of sound On Screen Display Analogue TV standard Television channels available on subscription e g PREMIERE Standard for internal decoder interface for Pay TV See Short Techni
43. e reception and recording properties of your UFD 580 twin DVR Sat receiver such as 1 recording one programme and at the same time viewing any other programme or zapping through the programmes and 2 recording two different programmes at the same time the two tuner inputs of the Sat receiver must each be supplied with a dedicated satellite signal from the antenna system Sat outlet The receiver tuner inputs are factory preset on the installation menu for 1 8 2 mode meaning for two separate Sat antennas If you only have one antenna connection available we recommend Coax cable with F connectors you interconnect the output of tuner 1 and the input of tuner 2 by a coaxial cable with F connectors AC 98V 240V 50 60Hz max 60W IF INPUT AAA 950 2150MHz 14 18V max 400mA 22kHz DATA 1 0 ERE E DISEaC kh DIGITAL TWIN O oononnonnn Y SA m4 E i UFD 580 20210024 am CE E O LNB IN LNB2 IN LNB LIN LOOP OUT LOOP OUT OPTICAL USB SPDIF VOR AUX LA Then Loop mode must be selected on the installation menu for the tuner input You will find the Tuner input option by pressing the eo button Then select Installation LNB configuration and confirm the satellite you are receiving by pressing 0x You can then make the settings here though a restriction on this is that with tuner 2 you can only receive the additional
44. e transmission frequencies are located in the following ranges 10 7 11 7 GHz Low band 11 7 12 75 GHz High band Installation Menu However the input frequency range for the receiver is in the range 950 to 2150 MHz The high frequencies are therefore converted into a lower frequency using the oscillator frequency LO frequency L O LNB local oscillator Different oscillator frequencies are used for the conversion depending on the satellite frequency range and the system type For ASTRA and EUTELSAT reception systems this is normally 9 75 GHz 9750 MHz for the lower frequency range low band and 10 6 GHz 10600 MHz for the upper frequency range high band Older reception systems still use a 10 GHz oscillator frequency in the low band range which is not normally suitable for digital reception The receiver generates the frequency to which it needs to adjust by subtracting the oscillator frequency from the satellite transmission frequency saved for each programme You only have to set the oscillator frequency used by your reception system Before chancing the LO frequency you must therefore ascertain whether this is actually necessary The oscillator frequencies listed above are the factory settings Changing the Oscillator Frequency Operation Receiving Two Satellites Press ox to move to the right hand section of the LNB configuration menu The setting for L O High is highlighted in colour You can now use the number but
45. eceiver refer to the connection diagram provided at the end of this manual and the instructions for the video recorder In order to make a VCR recording Record the satellite receiver must be switched on or the timers must be pre programmed see Timer Settings section For VCR playback Play the satellite receiver must be set to standby so that the signal path is switched through from the VCR AUX Scart socket to the TV Scart socket You must set the Scart socket of the Sat receiver to AUX with the 0 button in order for your TV set to automatically play back the picture from the video recorder In this setting the picture from the video recorder is switched through to the TV set during playback If you set SAT by pressing the 0 button the Sat receiver will have priority In the TV setting the video signal of the TV set has priority TV mode is indicated by the green LED on the front panel For system reasons the TV and VCR Scart sockets carry the same signal 83 Software and Programme List Update 84 Thanks to digital technology you can receive satellite updates of the software and programme list for your receiver The Software Download sub menu tells you whether new software or programme lists are available The only prerequisite is that your satellite reception system is aligned with ASTRA 19 2 East Press eo to access the main menu use the lt gt button
46. ed access by third parties This protects the receiver against changes to its reception settings by unauthorised persons At the same time you can activate a child protection function parental control which bars selected programmes Keep your password in a safe place so that you always have access to your programmes should you ever forget it The password is set to 0000 in the factory and is inactive Press eo to access the main menu Press y to select System Parameters and confirm with 0x Main Menu installation Timer Language Common Interface i OK Next MENU EXIT Exit Now press the OD buttons to select the Parental Control function and confirm by pressing 0x If you have set a password you will be asked for it Password Y pa Parental Control ip ed ae Lock Channel Editing Lock Installation New Password Verify Password Personal P MENU Main EXIT Prev You can make the following settings here Age Limit This setting is only effective if the corresponding lock out signals are transmitted Lock Channel Editing Yes No With this option you can lock or unlock the editing function for programme lists Lock Installation Yes No With this option you can lock or grant access to the installation menu New Password Here you can enter your new password using the number buttons Verify Password Here you enter your new password again using the numb
47. ed back so far The symbol for the current selected playback function appears at the left and next to it the current playback time and total duration are displayed Important The 4 speed slow motion function cannot be selected when the control console is displayed on the screen during playback Hard Disk Recorder Setting Index Marks Skip Points Note During playback and with the control console displayed opened with the x or button index marks skip points can be set and can then be displayed above the time bar by pressing the 0 button This function is used to skip specific parts of a recording from the beginning marker to the next end marker during the next playback so as to cut adverts out of films for example You cannot set index marks as long as the small control console pop up opened with the eo button is on display Also you cannot set index marks atthe end ofa recording Further control console functions can be displayed during playback To access them first press the i or button to open the control console then the ve button If there is a block of adverts at the end of your recording which you want to remove you must use the Split take function The split portions of the recording will be saved to the hard disk separately You can then delete the second part of the split the block of adverts from the hard disk in the same way as you would delete any other recording To do this
48. er buttons to confirm it Personal Here you enter the receiver identification which is displayed when the receiver is turned on This is useful for identification in case of theft Refer to the Operating Instructions section for information on how to use the number pad buttons on the remote control for alphanumeric input The factory default setting is Twin DVR receiver This completes all the settings to secure and identify your satellite receiver If you have forgotten your password you must contact your dealer who will be able to unlock your receiver for you 63 Password Parental Control 64 Similarly to marking your favourite programmes with the apple symbol you can set up a child lock to prevent unauthorised access by children The programmes are marked with the padlock symbol in the TV or Radio programme list AV Channel List Astra Astra XXP 23 12 552 GHz TELE 5 Verticab 14V Sonnenklar TV 22 000 gt a NUT 068 ASTRA HSE24 er RTL Shop FAV DEI NEUN LIVE Tel LOCK ADD VC Dartart MOVES 1 MODE p a gt Page Up On OK Watoh WENU AMAN EXIT Exit O Move Press 0x to access the TV channel list Select the programme you want to lock using the OD and AQ buttons You can move the bar page by page or line by line with the G and the OD buttons The selected programme is highlighted by a coloured bar Confirm the selection with the g
49. ge PIP Symbol rate Transponder Video bit rate Viterbi rate 94 PCR PID is the identification number for the synchronisation signal The PCR PID is normally identical to the video PID For programmes broadcast in multiple languages the audio PID can be entered manually to assign a different language to the TV programme After the PID is entered the digital receiver automatically selects the audio data identified by the PID number from the data stream and assigns it to the video signal The programme package for a digital transponder normally includes several TV and radio programmes Each programme package has a fixed assignment for the transponder transmission frequency for polarisation horizontal or vertical for the symbol rate and for the Viterbi rate or error rate Picture In Picture function The symbol rate describes the quantity of data that is transmitted per second The symbol rate is measured in MSymbols s and is equal to the number of symbols received per second A transponder is a satellite channel which transmits TV and radio signals A satellite has several transponders Analogue transponders transmit only one TV programme and possibly multiple radio programmes on the transmission frequency Digital transponders simultaneously transmit several TV and several radio programmes at a transmission frequency lf a programme provider is broadcasting several TV programmes via a digital transponder we refer to th
50. he end of the set time by the timer the receiver automatically switches to standby Simultaneous recording of two programmes and playback of a recording is possible As soon as the recording and playback options are exhausted the following display appears After the time either preset by the EPG or entered by you elapses the recording automatically stops The HD programme guide menu appears Press to return to the original programme Important If you are already recording two programmes you can only see the programmes that are on the transponders being received You can easily search for other programmes without interrupting the recording You can however play back a programme that you have already recorded see Playback You can also stop the recording yourself To do this press the button and the HD programme guide will appear If you press the button again you will be asked if you want to stop recording Confirm your choice with the relevant colour button or quit the prompt screen by pressing E Special Functions Recording cancelled then appears on the screen and the HD programme guide remains displayed The programme which was being recorded up to this point appears at the end of the list Press to restore the normal TV picture Do the same for a single recording HD Program Guide Play time Free 72 4 GBA ES 05 04 2005 08 49 Panoramahdder Bergwottor P 0K gt Watoh
51. he timer menu lt provides all the EPG information for around 60 TV channels at no charge without you having to change programme and also offers schedule information up to a week ahead depending on programme provider Accessing the TVTV EPG for the First Time Press e to access the tvtv EPG The first time you access it and following a factory reset you see the following on screen display To ensure the functionality of the TVEV EPG the satellite scan for the ASTRA satellite with multifeed reception for All satellites must be run This process downloads the necessary signal identifiers for the Tvtv EPG SID TSID and OID Press ox to switch to the Satellite search menu Use the arrow buttons OOO to navigate around the menu items and select options Confirm your selection and start the scan by pressing 0x When the search is finished press 0x Press three times to quit the menu and return to the normal TV picture Then press to switch the receiver off The front panel display indicates As soon as the display no longer indicates twtw you can switch the receiver back on by pressing the button and begin using the tvtv EPG The tvtv display is usually shown for about 30 minutes The download may take anywhere between 20 and 60 minutes however depending on how much data is waiting to be transferred from the tvtv to the receiver 29 Accessing the TVTV EPG The tvtv EPG is accessed by
52. in Stra e 1 3 P O Box 100 444 83004 Rosenheim Germany Antennen Electronic
53. k and play back one programme from the hard disk or record two programmes to hard disk and view a programme from one of the programme packages being received To take advantage of all these opportunities complex operating procedures are necessary You should therefore read this operating manual thoroughly The RC 660 remote control supports up to four devices as well as the receivers of the UFD 5xx not UFD 552 554 558 and UFD 4xx families To configure a receiver to an infrared code Switch on the relevant receiver On the remote control simultaneously press Address 1 er 0 to Address 4 En O 0 To configure the remote control to an infrared code Switch to Address 1 1 to Address 4 4 m red Kathrein UFD 5xx code for remote control RC 400 The RC 600 and RC 650 remote controls cannot be replaced Remote Control Menu Functions Sound on off 0 0 Number input for programmes timer etc Power on off E Videotext Teletext Tone selection Switch TV Radio Prog Make channel favourite Programme info picture in picture from 2 tuner or from hard disk Lock channel 3 Volume Programm selection up down EXIT Confirm input AWW Arrow buttons Exit menu Electronic Programme Play back hard disk Guide content Fast forward Freeze frame video timeshift Recording Slow motion during playback Stop recording playback
54. l 11 X X Data signal 12 Red earth 13 X X Data earth 14 Red signal C 15 X X Blanking signal 16 X X Video earth 17 X X Blanking signal earth 18 X X Video output FBAS Y 19 X X Video input 20 X Connector shielding 21 X X VHS S VHS Switching The Scart sockets are switchable between VHS and S VHS The switch is made in the System Parameters A V Mode menu VHS RGB The RED signal is connected to terminal 15 the Composite Colour output to terminal 19 S VHS C Y The C output is connected to terminal 15 the Y output to terminal 19 90 Connection Example TV 00000000007 N VCR AUX Cinch 8 pe E TIN TENG san gha Lah DVD VCR Hi fi system Electrical digital sound for Dolby Digital system Dolby Digital system 91 Troubleshooting In the event of a malfunction first check all the cable connections and operating states 1 Receiver and TV set power plugs are connected to wall socket 2 Antenna cable on receiver input 3 Receiver and TV set correctly interconnected by a Scart or cinch cable 4 Audio connections are made to hi fi or Dolby Digital system as appropriate see previous page 5 Receiver and TV set hi fi Dolby Digital system are switched on check power indicators 6 Receiver is responding to remote control A selection of troubleshooting tips is offered below Consult an antenna specialist to have it checked and repaired as necessary Antenna signal of Sat rece
55. larisation The desired programme can be chosen using the bar cursor or by entering the relevant number and is then confirmed by pressing ox In the bottom right hand corner you will find the Programme Channel Settings menu The factory settings for programmes and channels can be changed here Press the FAV button red to save the channel shown as a favourite channel PIP A button green to lock the displayed channel 6 button yellow to move the channel to another position TV R O button blue to delete the displayed channel from a position Press to add a new channel Press to select the programme mode of the programme list Always follow further instructions or press to quit For more information refer to the Programme Selection section Videotext Teletext This symbol in the programme display shows you whether Videotext Teletext is broadcast for the selected programme When you press the button the receiver processes the broadcast Videotext Teletext service for your TV set to display even when the signal is encrypted During the search the programme page here P100 which is being searched for is displayed in the top left hand corner and the permanent time display is shown at the top right P100 252 2DFtcx Mit dem Zweiten sicht man besser Bush in Bratislava umjubclt Papst wicder im Krankenhaus Visa Botschaft VB Jobabbau nur informicrtc in Deutschland H I
56. mes It is possible to save several different programmes in a list Programme List Generating a Favourites List Pay attention to the bar at the bottom of the on screen display It provides guidance on what to do next Each family member can then save their own favourite programmes and call them up at any time Entering a password allows you to protect the programmes against unauthorised use see Password section The currently selected list is highlighted by a coloured bar The selected programme appears in the top corner of the screen You can then press the red button to flag the highlighted line with the apple symbol The next programme from the programme list is automatically selected and appears on the small screen in the top right hand corner You can then flag your next favourite programme with the apple symbol You can assign names to the individual Favourites lists to arrange movie or sports channels together under Favourites list 1 for example You can also enter the relevant user s name such as Peter Karen Grandma Grandpa Press the ox button to access the channel list Press the red button to call up the Favorite State Favourites status display Use the OD buttons to select a Favourites list It is highlighted by a coloured bar RV Channel List a ptr a tat 18V MSPS _ 27 En Favorite 2 ra Favorite 3 ZO 20 Favorite 4 34 Ku kasan OS Seleot ME
57. meters Timer Language Common interface P OK Nert MENU EXIT Erit You can now view the help display for the Installation option by pressing i Main Menu This makes environment in which this reoelver oan reoeive good quality signals From satellites It contains LNB Configuration Antenna Setup Satellite Soan TP Edit Soan Factory Set gt TOK Next MENU EXIT Evit You will find detailed descriptions of the selected menu items in the relevant sections of the operating manual On Screen Display OSD TV Channel Identifier Radio Channel Identifier Error Signalling Press to quit the help function and return to the main menu Press again to return to the original programme you were receiving 44 Astra 31 3sal Wunderbare Welt im Wald 7235 14 00 E vz MY Herrscher siner versunk 14 00 540 The channel identifier is displayed for a few seconds each time you change the programme or constantly if you press the x button The Z indicates that a channel is being received even if no picture can be seen e g radio The TV symbol indicates a TV channel adjacent to it is the selected programme whether Videotext Teletext is being received and the current time The on the third line indicates the programme selection from the master list If the Favourites list is selected the apple symbol appears here This is followed by the programme title the start and end time of the curren
58. n to the other channels listed above you must also perform the essential satellite scan described on page 2 for the HOTBIRD 13 East satellite However as you initially only have the possibility to run the scan for one or all satellites you must select the All satellites option taking around 1 hour If you have already started the scan for the ASTRA satellite alone you will not see this scan prompt You can still run the scan for the HOTBIRD 13 East satellite too though as described in the Satellite Scan section You do not need to perform a factory reset 41 Hard Disk Recorder Recording and Watching TV The two tuners and the hard disk of your twin DVR Sat receiver offer you a range of possibilities to receive different satellites as well as to record and play back programmes The following table shows you which recording and playback options you have for each tuner input setting You will find the Tuner input submenu by pressing the eo button 3J kk Then select Installation LNB configuration and confirm the satellite you are receiving by pressing 0x You can make the settings here LNB Configuration Overview Tuner input Recorder 1 amp 2 Record and view one programme from a transponder in a polarisation eee Y Y Y Y Record one programme and view an additional programme from a single transponder in a polarisation plane Y Y Y Y Record one programm
59. nd on the SAT 1 Videotext Teletext service on the Internet or in TV and radio magazines Your receiver is factory fitted with the latest software version We are however constantly working on adapting the software to the wishes of our customers and to developments in technology The Software and Channel List Update section contains additional information Please keep the original packaging in case you need to return the product at any time The hard disks are fragile due to their construction and are only adequately protected in the receiver by the original packaging If receiver is not shipped correctly the warranty on the hard disk will be voided UFO micro and UFO mini are registered trademarks of KATHREIN Werke KG DiISEqC is a trademark of Eutelsat Contents ed 21 rs A a e od 5 o A KAIN AA a da a ae ee A aa Safety Instructions Important Information RecelVer FeatUrOS cio aa Remote control RC 660 Remote Control Menu Functions 2 20 02000000nanananananananananan an an an anna Controls Displays und Connections ueurssns n0nnnnnnnnonnnnnnnnnnnnnnnn nenn View of front panel flap folded down View of rear panel Front Panel Controls and Displays Rear Panel Controls and Displays Important Note on Initial Operation of the Receiver on a UFO micro System Operating INSTUCHONS usais Menu Concept Alphanumeric Inputs Alphanumeric Assignment of Remote Control Number Butt
60. nfiguration Antenna Setup Satellite Scan DISEACIUFO Setup Factory Set On Air Download Y OK Next MENU EXIT Prey package of a specific programme provider You can obtain this information from the SAT 1 Videotext Teletext service from TV and satellite magazines as well as from the Internet Press to open the menu 77 Installation Menu Transponder Selection The following settings are now possible select items with E y IP D d 5 i gt TP Frequency TP Edit Scan a Polarization Symbol Rate Scan TP Delete so o a D MENU Main EXIT Prey Select desired satellite with a or gt Select transponder frequency with 4 or gt Select polarisation with or gt Select symbol rate with number pad buttons Select scan mode for FTA only or FTA and scrambled programmes with or gt Delete transponder refer to note on page 79 The bar chart shows the relative signal strength and is not an indicator of the quality of the reception system Start the scan by pressing from the Scan entry TP Edit Scan E nn a oo n e _ A P a gt Page Up On TOR Watoh MENU J EXIT e Press 0 to exit this menu and skip to the programme highlighted by the cursor bar 78 Installation Menu Press to return to this menu where you can search for additional transponders
61. nhalt A Z Nachrichten etter Vorschau Sport gt Ae lcefontarifc Programm 3 ktien Anlagen When the search is finished the Videotext Teletext being broadcast by the relevant programme provider appears The individual pages can then be opened using the number buttons During the search a white star flashes in the top left hand corner of the screen Press em or er to exit the Videotext Teletext 21 This section describes how you select TV programmes with your receiver and how you can set the desired volume The description of the functions assumes that the receiver has been properly connected lf you wish to connect up the receiver yourself please read the Connection and Setup section first Selecting a TV Programme Reception Status 22 The following information describes how to select other programmes and what the on screen displays look like To select additional TV programmes in ascending or descending order in the programme memory simply press the amp buttons after turning on the receiver 1 Das Erste i 10 00 Tagesschau 10 00 10 03 ES 11 DETE 10 03 10 30 Every time you press the button an on screen display shows you the selected programme together with the time the programme start and end times and the programme tite on an info bar provided the relevant data is being broadcast You can permanently show or hide this info bar by pressing the x button Encrypted
62. ntrol programme asks Confirm your answer by pressing the relevant button Press 0x to delete the programme location The change is saved and confirmed and the programme from the next programme provider in the programme list appears on the screen Manually Adding Programmes Pay attention to the bar at the bottom of the on screen display It provides guidance on what to do next Important You can only select satellites that are included in the Installation menu The procedure is similar to the method of adding programmes Press ok to access the channel list Press the button plus to display the menu for adding a programme Add Digital Channel TP Frequency Polarization Symbol Rate CH Name Video PID Audio PID PCR PID D MENU EXIT prey Here you can make the entries for the new programme or enter the available data The first line in the list is highlighted with a coloured bar You can use the OD buttons to move the bar up or down to the desired item 59 Programme List 60 The entry is made using the gt buttons and the number pad buttons You can set e the satellite being received e the transponder and transponder frequency e the polarisation and e the symbol rate The following items e Name e Video PID Programme Identification e Audio PID e PCR PID PCR Programme Clock Reference will only accept alphanumeric or decimal entries In
63. o 5 MHz 2 45 MSymbol s MPEG 1 2 compatible 1 5 15 MB s Vis gt 53 dB MPEG 1 2 Layer 1 and 2 32 44 1 48 kb s 40 Hz to 15 kHz Typ 770 TV Scart and Cinch gt 65 dB 4 MB 32 MB 80 GB Up to 56 hours Depending on data rate and refresh rate 230 V 10 50 Hz lt 35 W lt 3W 2x0 14 V vert 18 V hor 2 x 400 mA max 22 kHz square 0 6 Vss tone burst DISEQC 1 2 UFO micro UFO mini Technical Appendix Connections General Temperature range 2 Sat signal inputs outputs looped through TV Connection VCR AUX Connection Video audio output Digital audio output Digital audio format Data port for service Unit dimensions W H D Weight Ambient temperature ce 4 x F socket Scart socket 21 pin Scart socket 21 pin 3 x Cinch socket Optical standard fibre optic socket Electrical cinch socket Dolby Digital AC 3 Compressed PCM MPEG Stereo PCM RS 232 Sub D 9 pin USB 2 0 335 x 63 x 280 mm approx 2 75 kg 5 C to 40 C 89 Technical Appendix Accessories 1 infrared remote control RC 660 2 batteries 1 5 V type LR 03 size AAA Micro 1 Scart cable 1 operating manual Scart Socket Assignment Signal Connection no TV VCR AUX Audio right output 1 X X Audio right input 2 X Audio left output 3 X X Audio earth 4 X X Blue earth 5 X X Audio left input 6 X Blue signal 7 K X Switching voltage 8 X X Green earth 9 X X Data signal 10 Green signa
64. o exit the programme list and return to the programme already selected Selecting a TV Programme by Number Example You can select a different TV programme while a programme is running by entering the new programme s location number Use the number pad buttons O to 0 to enter the programme locations You want to select DSF at location number 15 the order of TV programmes is fixed in the programme memory so this only serves as an example To select this programme press the numbers O and one after the other The receiver waits for about two seconds for input of the next number Do not input leading zeroes in front of the number The 0 button is reserved for switching to AV mode The procedure for all other programmes including those with three or four digit location numbers is exactly the same 23 Channel List Switching to a Radio Programme You can switch from a TV programme to a radio programme by pressing the blue m button The receiver switches to the last radio programme selected The on screen display relating to the programme is shown just as for a TV programme The LED shows a small r together with the programme s location number You can return to the TV programme by pressing the same button All the functions such as the channel list work in the same way in radio mode as in TV mode 24 Common Interface N Follow the instructions given by your Pay TV provider The Common
65. olby Digital AC 3 The receiver has an electrical optical audio output for AC3 format Dolby Digital This gives you the opportunity to bring cinema quality sound into your living room The AC 3 sound is recorded and can be selected during playback Connect the corresponding digital audio output to a Dolby Digital system If no AC3 signal is received you can only make the normal stereo or mono settings and choose the broadcast languages 93 Programme List Favourites Pay attention to the bar at the bottom of the on screen display It provides guidance on what to do next 54 The programme channel settings made in the factory can be changed in the Channel List menu Access the menu by pressing the button You can organise and sort your preferred TV and radio programmes such as all English language programmes or those that broadcast with no commercial breaks These programmes are marked with the apple symbol in the TV and Radio channel lists which you can access by pressing the button ey The bar can be scrolled line by line or page by page using the OD and gt buttons to select the desired programme Or you can also enter the desired programme number using the number pad buttons sun Press the red m button to access the Favourites list selection Using the OD buttons you can select a Favourites list from 1 to 5 where you would like to save your favourite program
66. one Burst and DiSEqC Signal 80 If more than four control criteria are required in a reception system a DiISEqC control signal is required Which of the setting options Tone Burst or DISEGC is required depends on the components of the reception system You should therefore refer to the descriptions of the existing components switching matrices of the reception system Installation Menu Tone Burst Here the 22 kHz signal can be set as follows Switching states for setting Switching states for setting Switching states for setting 22 kHz Signal gt High Low 22 kHz Signal gt Pos A B 22 kHz Signal gt Pos A B and and and Tone Burst gt Pos A B Tone Burst gt Opt A B Tone Burst gt High Low Low 22 kHz Off Pos Tone Burst 22 kHz Low Tone Burst 0 High 22 kHz On High Tone Burst 1 Off Pos 1 Tone Burst On Pos 1 22 kHz Off Pos 2 Tone Burst Off Pos 2 22 kHz On On DiSEqC If the receiver is connected to a DiSEqC switching matrix set the menu option to On The switching criteria and the input assignment of the DiSEqC switching matrices must be observed You should therefore follow the description of the switching matrices or contact the engineer who installed the reception system DiSEqC Repeat If the receiver is operated in a reception system with two or more DiSEqC switching matrices connected in series cascaded the DiSEqC command must
67. ons Language Selection OSD Connection ANG SelUp asunsa nem Connecting the Unit Sat IF Connection Reception Requirements Reception System Presets Operation on one Antenna Connection TV and Video Recorder Connection Audio Connection SPDIF Connections Electrical Optical Inserting Batteries in the Remote Control A rear Getting Started Power Failure Safety Error Signalling Receiver Presetting On Screen Display OSD a Important On Screen Displays Help Function TV Channel Identifier Radio Channel Identifier Error Signalling TV Radio Channel List Videotex Teleton dad Channels O dea Selecting a TV Programme Reception Status Selecting a TV Programme by Number Switching to a Radio Programme Sommon intertace aia Tein Functions ccccececececscecencececececeeaceceeeeeneaeacaneaeaeneneasaneaeneneneaneneaeaeaeeneanans Picture in Picture PIP Time Shift One Touch Recording IVTV EPG and TIME oscene aaan Accessing the TVTV EPG for the First Time Accessing the TVTV EPG Current View Contents Programme List Highlights Programmes Sorted by Category Search Function Details Programming a Recording Timer List Key to Symbols Channel List Hard Disk Recorder cccccceccecececccececececeecaceceneneaceneaeneneaeaceneaeaeneneansneaeneneass Recording and Watching TV LNB Configuration Overview Tuner input Recording Hard Disk Capacity Time Shift Recording One Touch Recording OTR
68. ording the relevant take must be selected in the hard disk contents and started by pressing the button HD Program Guide LAU eR eR cd Play time 00 01 Free 72 7 GB 92 7 05 04 2005 08 46 Ein himmlische Fame P OK Watoh Delete EXIT SS Edit e Hard Disk Capacity Please check that there is adequate hard disk capacity available before every recording Press to view the hard disk contents programme guide and the available hard disk capacity 43 Time Shift Recording 44 If you cannot catch the beginning of a programme because you are occupied with something else you can watch the programme in time shift mode You can start recording the current programme you are watching by simply pressing the m button The receiver switches to hard disk mode y l Bayorischos F aes U 00 00 00 00 00 00 Stereo Panoramabilder Bergwetter The red T in the info bar indicates time shift recording You see a freeze frame image while the recording is running in the background For a short time R flashes at the top left of the TV screen and the red standby LED on the front panel of the receiver flashes To start time shifted playback press the button You can control the recorder fast forward rewind pause and playback functions with the corresponding buttons When you press the button the TV picture freezes but the recording continues in the background Press again to resum
69. ot connect the unit to the mains until all installation work has been properly carried out Refer to the information in the Safety instructions section Connect the Sat IF inputs on the receiver to the satellite reception system Use coaxial cable with a standard F connector If the F connectors are not yet fitted on the cable strip the insulation from the cables as shown in the following illustration and carefully twist the F connectors onto the ends of the cables until they are securely fitted When fitting the connector make sure that no wires from the braiding are touching the inner conductor so no short circuit can occur The quality of the reception signal depends on the connection Make sure that your own satellite antenna system is equipped at least with a universal LNB for digital reception in the high band range The presets for the control signals have been made for standard reception systems i e 14 18 V for polarity reversal and 22 kHz switching signal for low high band changeover on multi feed reception systems The preset will need to be changed in the installation menu under DiSEqC TM if UFO micro or tone burst switching matrices are used in the receiving system Refer to the section headed Installation menu DiSEqC menu Be sure to follow the operating instructions for the matrix used 13 Connection and Setup Operation on one Antenna Connection To enable you to utilise all th
70. play It provides guidance on what to do next 58 You can sort the programmes to meet your own requirements Sorting involves moving entries around the channel list AV Channel List Astra Astra Das Erste 101 11 953 GHz AOP Ae Horizontal 18V SAT 1 27500 MSPS RTL Televisio ASTRA RTL2 Super RTL _FAV pe DEL VOX LOCK ADD ProSieben AL MOVE i MODE b A Page Up On OK Watoh MENU AMAIA EXIT Exit Move Press ok to access the channel list Use the arrow buttons CONO or the number pad to select the programme you want to move The line with the current running programme is highlighted in the list by a coloured bar and the programme appears in the top corner of the screen Press the yellow 8 button to lock on to the programme you want to move The lettering in the bar turns red You can now move it to the desired position Press the yellow button again to place it at its new location Press le to exit the programme The change is confirmed and is displayed for a few seconds on the screen The relocated programme appears on the screen and is now stored at its new location in the channel list Programme List Deleting Programmes The procedure is similar to the method of sorting programmes Press ok to access the channel list Use the arrow buttons CONO or the number pad to select the programme you want to delete Press the blue button to confirm the deletion The co
71. programme In the bottom section of the screen is an information bar showing the name of the programme provider the time the timer settings the programme status and title provided those details are being broadcast The LED display indicates the programme s memory location number The red standby indicator goes out You can now receive the factory preset TV and radio programmes and TVR O O call them up by pressing the buttons Press O blue and amp to select radio programmes Press the blue O button again to return to the TV programmes For details of how to save additional TV and radio programmes refer to the TV Radio Programme Lists section Please check the time is correct according to whether you are on Summer or Winter time When you switch on the last reception status set is always restored After a power failure the receiver automatically powers up obtains the time from the reception signal and then returns to standby This preserves the timer settings If the message Weak signal or no signal appears on the screen as well as the display for the last programme received check the installation of the system and or the receiver settings If this only affects individual programme slots there may be an interrupted signal from the programme provider or a fault in the reception system cable or satellite system First of all check the connection configuration and whether the default receiver settings ar
72. programmes are indicated by the message Encrypted channel Verschiusselter Kanal a Astra 10 03 Spirit Der wilde Musta 10 00 1 30 E Helden aus der zweiten 1130 13 30 To view these programmes you will need an authorisation card a PCMCIA card or Smartcard from the Pay TV provider see Common Interface section The CA module and Smartcard are not included in the supply package Channel List Pay attention to the bar at the bottom of the on screen display It provides guidance on what to do next A further option for selecting a different programme is to press the button The TV channel list is then displayed The top right hand column provides information relating to the satellite being received the transponder and its transmission frequency the polarisation the symbol rate and the encryption The left hand column shows the programme location and name the type of signal being received F TA encrypted the favourites and any locked channels RY Channel List All Liat Astra 25 EinsFestival RUE Weare coe 26 EinsMuXx kanaka SV 27 Entra 27500 MSPS 28 ZDFdokukanal 29 ZDFinfokanal 30 ZDFtheaterkan 32 Kika d T MOVE i mone P A Page Up On OK Watch MENU CU 0 9 Move 4 Press the OD buttons to move to the next programme and use the o0 buttons to jump to the next or previous page You can also select a programme by entering a number Press the button t
73. programmes of the plane currently set by tuner 1 e g Horizontal High This will only work when receiving one satellite not in multifeed reception If only tuner 1 is connected with no connection to tuner 2 the setting 1 must be selected for the tuner input You can then have only the possibilities offered by a normal single receiver available to you If this setting is not made malfunctions will occur and the following message will be displayed Weak signal or no signal 14 Connection and Setup TV and Video Recorder Connection Audio Connection Connect the satellite receiver TV Scart socket and the TV set by a Scart cable see Connection example If your TV has a stereo feature you can receive the sound in stereo via the Scart connection Connect the satellite receiver VCR AUX Scart socket and the video recorder likewise by a Scart cable For system reasons the same video signals are to be found on the Scart outputs and on the video cinch output If you are recording using an external video recorder remember not to operate the receiver during recording otherwise all the on screen displays will appear on your recording If you want to play the sound on your hi fi system connect the audio cinch sockets to the input sockets on the hi fi system with an appropriate cable see Connection example SPDIF Connections Electrical Optical The electrical SPDIF cinch output an
74. ption system In Installation menu check LNB is missing or faulty configuration for satellite in question High L O 10 600 GHz and Low L O Incorrect oscillator frequencies set in 9 750 GHz and change as necessary Weak signal or no signal warning appears on some or all programmes LNB Configuration menu Connect tuner input LNB2 IN with Only one cable from Sat system second cable connect coaxial cable connected with F connection of SAT socket OR In Installation menu change LNB configuration tuner input to 1 if only one satellite being received SONATE A u IS Latest operating system software displayed under Main SW and p 9 SY Not possible to download again i i already installed on computer cannot be changed to YES l Set infrared code 1 as described in Remote control no longer Receiver or remote control command set l operating manual on page 7 check responding may have been unintentionally changed batteries In Installation menu select TP Edit Scan enter frequency polarisation and symbol rate and then under Scan press OK No new programmes can be added Wrong menu option selected to programme list In System Parameters menu check Summer time Yes No and change as Summer time yes no setting wrong necessary Wrong time being displayed Switch off receiver at mains switch from current running programme e g ARD or ZDF wait 10 second
75. reen button Lock and the padlock symbol appears in the bar You are automatically taken to the display for the following programme in the programme list Press the green button Lock to lock another programme or return to the locked programme with the arrow buttons and press the green f button Lock again to cancel the lock The padlock symbol disappears Press ok to save the change Then the following programme in the list will appear and the info display will be shown for a few seconds Password When the locked programme is selected using the number buttons or the channel list the message Channel is locked appears and the programme cannot be viewed You are asked to enter your password in order to view the locked programme hannel t Se fi Astra 55 NEUN LIVE Tel sormenklar TV ea VU Alive Leichter Leben 65 Using the Front Panel Backup Operation 66 If you have misplaced your remote control or if the batteries are empty you can still operate your receiver from the front panel There are six buttons on the front panel On Off Menu Select and the horizontal and vertical arrow buttons The unit is switched on and off with the On Off button The menu button like the eo button brings you to the main menu The vertical arrow buttons have the same function as the G buttons and bring you to the submenus The horizontal arrow buttons have the same function as
76. s and then switch back on A incorrect time was imported from the reception signal The following programmes cut out DECT telephones are operating on the or Weak signal or no signal same frequency as these programmes appears PRO 7 SAT 1 Kabel 1 Interference may occur due to Consult your antenna specialist DSF N 24 Tele 5 9 Live HSE 24 inadequate level or poor shielding of and Sonnenklar TV cable Programmed timer settings cannot ne umer Sud sale pernanenty In Timer menu under Deactivate set displayed and do not have to be cleared ln be cleared l No but deactivated Black or blue screen no on screen Scart connection to TV deactivated by Press 0 button repeatedly until displays accidentally pressing 0 button Scart SAT appears on screen 92 Short Technical Guide DISEgC DiSEqC components DVB MPEG 2 EB NO ratio FEC OTR PID DiISEqC Digital Satellite Equipment Control is a communication system between a satellite receiver master and the peripheral satellite components slaves such as LNBs multi switches rotating antenna systems It is a single master multi slave system i e there is only ever one master in the satellite system All activities start from the master lf DISEqCT switching matrices are cascaded the master receiver must transmit the DiSEqC signal several times so that all DiISEqC multi switches in the cascade receive their commands
77. s recording function the twtw EPG locates the series in question in the updated schedules and automatically programmes recording of them A change in the time the series is broadcast is no problem for the tvtv EPG as its programming is based on the series title This does however mean that the schedule change needs to have been notified prior to the last update of the tv EPG FAV The timer list recording schedule is accessed by pressing the red button The timer list shows all the programmed recordings You can use the 96 buttons to toggle back and forth between the master timer list and the once and series displays You can scroll line by line or page by page through the timer list using the arrow buttons ANO b Tuesday 05 04 2005 9 08 40 Timer list gt n Tue Hr fernsehen 17 13 18 05 Q Zebras die wilden Pferde Afrikas Tue Bayerisches F 17 43 18 48 Die Abendschau Tue VOX 18 13 19 50 Wohnen nach Wunsch Ein Duo f r vier Bayerisches F 18 43 19 06 Abend Programm KABEL1 20 13 23 00 _ Jerry Maguire Spiel des Lebens KABEL1 00 38 01 40 Ki Discovery Bayerisches F 17 43 18 48 Die Abendschau 37 Note 38 Tuesday 05 04 2005 9 089 41 timer lisi Hr fernsehen TAKE Zebras die wilden Pferde Afrikas Bayerisches F 17 43 Die Abendschau Bayerisches F 18 43 Abend Programm KABEL1 20 13 Jerry Maguire Spiel des Lebens KABEL1 00 38
78. s to select the Installation submenu and confirm with ok Then move the cursor bar to the On Air Download menu item and select it by pressing ex Your receiver automatically searches for the ASTRA transponder which broadcasts the current software and programme list E If there are no new versions an on screen message appears to inform you of this The light coloured cursor bar in On Air Download can be moved with the y buttons Press under the Display Info item to get information about the software and programme list being broadcast The Display Info Main SW operating software and Ch List channel list options are automatically set to Yes if new information and content is available vai Software and Programme List Update After the Display Info request an on screen display appears which you should use as a guide Pay attention to all on screen displays Following a software update you must reset Winter Summer time as appropriate You can also download the updates from the Internet at 3 MN lt r N ae NESE nn EN AS You can move the light coloured cursor bar using the y and or gt buttons to select the item you want to deactivate No Items that are already inactive cannot be changed If you only want to update the software but leave your channel list alone deselect the Channel List field or vice ver
79. sa You can also request Info Text only To update move the cursor bar to Start and confirm with ok The receiver then begins the update and displays the following message where applicable Bie information UFD 580 vom 30 3 2005 Sehr geehrter Kunde ab sofort kann SW 2 02 nut folgenden ferbesserundgen geladen werden Sommer Winterzeit Umstellung P P Tasten tur 24 Std Sprunge Symbol f r verschl sselte Programme Verschieben von Programmen wird mm EPG sofort umgesetzt Scrollbar im EPG Menu Weitere Infos www kathrein de Verlassen mit EXIT Once the update is complete the receiver is re initialised and starts operation again In case of an error or no signal the message Download failed appears Never turn off the receiver during the update process as otherwise you could lose the entire software If this happened the receiver would have to be re installed at the factory or using a PC and zero modem cable During the download Please wait flashes on screen 85 Receiver to Receiver Data Transfer Preparations Programme List Download Your receiver is able to receive data from another receiver via its RS232 port For this the two receivers are interconnected via a so called zero modem cable The transmitting receiver is the master and the receiving receiver is the slave The master and slave are first switched to standby mode and then disconnected from the mains b
80. search through all the information available to the tvtv EPG programme name description title cast director details for a word or phrase you enter with the results being displayed in a list From the Highlights menu use the 96 buttons to go to the Search function You can use the number pad to input letters in the search form The assignment of letters to the number pad buttons is displayed at the bottom of the screen as follows Use the buttons to enter a space or to delete the last letter entered Press ox to start the search Tuesday 05 04 2005 08 28 Das Erste ARD Buffet 3sat Der Landpfarrer ZDFinfokanal heute Sport ZDF heute Sport EinsFestival Hierzuland DSF D SF Das Sportquiz The results found are displayed at the left in the main display box If the programmes found do not fit on one page you can scroll page by page as well as line by line as usual using the arrow buttons WMAP Press 0 to start a new search This function is useful if you are looking for programmes about the country you are going to visit on holiday for example 33 TVTV EPG and Timer Details Press x in the tvtv EPG to call up details on the selected programme The information is only available if the x symbol is displayed next to the programme title The symbol only appears once you have selected the channel and programme by highlighting it with the yellow cursor bar in the v
81. ss the Record menu the timer 30 Programme List Page by page scrolling using the IL buttons can be very useful in locating data several days aheaad as it is very fast You can scroll line by line or page by page through the channels using the arrow buttons NICH or access channels directly using the number pad Press ox to confirm a change of channel Press gt to view the upcoming programme schedules in 15 minute blocks Press O to return step by step to the start point current time or press the green f button to go back directly Quit the EPG by pressing either or er Press the yellow m button to access the schedule for the programme to which you are currently tuned in the tvtv EPG The following display appears example 9 08 24 O Tuesday 05 04 2005 4 gt 2 Tele Gym Die Abendschau Fliege Unkraut Verbraucher Tipp Die Sprachstunde Alpan Donau Adria Kunst amp Krempel Schwaben amp Altbayern Neues vom SGderhof Schlawiner Club You can scroll line by line or page by page through the programme list of the selected channel using the arrow buttons ADO Press the gt buttons to switch channels and then view the new channel s programme list The x symbol next to the programme title indicates programme details are available to view see Det inform Press the red 0 button to place your selected programme in the Record menu see Record 31 TVT
82. t UFO micro Press and change your selection to RESET by pressing GP Confirm your selection by pressing Oona A WO N 7 Press to guit the UFO menu press Q to save your changes 8 Press three times to get back to the starting point Press to switch the receiver to standby mode Now you can connect the receiver to the ESU 32 outlet Press to switch the receiver on The registration is then performed automatically the screen briefly shows UFO micro active Now perform a UFO micro reset as described above items 1 8 Operating Instructions Menu Concept Note Pay attention to the bar at the bottom of the on screen display lt provides guidance on what to do next Alphanumeric Inputs Pay attention to the bar at the bottom of the screen with details on the relevant menu item The structure of the menu concept is based on logical operating sequences The current selected programme always appears in the upper right hand corner of the screen The selected menus sub menus and positions as well as the parameters to be set are each highlighted in colour The menus are self explanatory to a great extent For additional information press the x button See On screen display Help function Main Menu installation Timer Language Common Interface D OK Next MENU EXIT Exit The main menu is opened by pressing the eo button and the sub menus are selected using the
83. t Note on Initial Operation of the Receiver on a UFOOmicro System It is absolutely essential to carry out the following before and while registering receivers on the EXU 544 UFO micro single cable matrix 10 Connect the receiver to the TV set but do not yet connect it to the UFO micro ESU 32 outlet You must first check the following settings on the LNB Configuration menu and change them as necessary Press the D button to switch to the main menu Press Aj to get to the installation menu and confirm your entry by pressing Press Gj to get to the LNB configuration menu and confirm your entry by pressing Press OD to select the ASTRA satellite and confirm your entry by pressing Press a to select Tuner input and press 00606 to change the selection to 1 amp 2 Press to quit the set up for the ASTRA satellite OF OW E gt a You must run through steps 4 6 for each satellite received T Press three times to get back to the start screen 8 Interconnect the LNB1 LOOP OUT tuner output and the LNB2 IN tuner input by a coaxial cable F standard connector Now carry out a UFO micro reset on the receiver as described below Press the D button to switch to the main menu Press OD to get to the installation menu and confirm your entry by pressing Press OD to get to the DiSEqC UFO set up and confirm your entry by pressing Press a to select the UFO option On the UFO menu press a to selec
84. t programme and the next programme if this data is being transmitted The message for the set radio channel has the same layout A radio receiver symbol in the top left hand corner indicates that it is a radio channel m it information 31 Isat lt 13 48 Wunderbare Welt im Wald 13 15 14 00 an v2 Horrscher sinsr vorsunk 14 00 15 40 gt d Ba Weak signal or no signal indicates that an error has occurred in the reception system or in the receiver settings or that the transponder is not sending The channel identifier shows a satellite antenna instead of the Z Check the Sat IF connection and the LNB configuration The list of service settings at the end of this manual can be used to help you do this 19 On Screen Display OSD TV Radio Channel List 20 AV Channel List All List Astra EinsFestival 1101 11 953 GHz EinsMudx Horizontst 18V EmaExtra 27500 MSPS _ 2DFdokukanal 2ZDFinfokanal r y ZDFtheaterkan FAV DEL Cs ale ae el Lock ADD KiKa H MOVE i MODE Page Up On OKD Watch MENU Main EXIT Exit O 9 Move Press the 0k button to access the channel list At the top left is a for the complete list Information about the channel the programme provider and whether the programme is currently encrypted is shown in the column underneath In the upper right hand column are details of the satellites received the transponder and its frequency and the po
85. the OD buttons The select button has the same function as ex Because there are no number buttons no password protected functions can be called up Setting System Parameters Pay attention to the bar at the bottom of the on screen display It provides guidance on what to do next You should not change the following settings without a good reason as they are factory settings or operating settings that are tailored to your reception system New settings are only required if the reception system is changed The selected menus sub menus and positions as well as the parameters to be set are each highlighted in colour The menus are self explanatory to a great extent Help for the selected item is available by pressing the x button Press 5 again to exit the help Main Menu Timer Language Common Interface P OK Next MENU EXIT Exit The main menu which is always accessed with the f button consists of the following submenus e System Parameters e Installation e Timer e Menu Language e Common Interface 67 Setting System Parameters System Parameters Parental Control System Information Local Time Timer 68 Select the System Parameters menu with the eo button the OD buttons in the main menu and 0x Use the lt buttons to select the further items The basic settings which can be made here are described under the parental lock setting information in the
86. the TV The tvtv EPG update is only started if no timer recording is programmed within the next hour The tvtv EPG is broadcast over the ASTRA satellite at the frequency of 12 603 75 MHz with a symbol rate of 22 MSymb s and horizontal polarisation 18 V If you have accidentally deleted the transponder at this frequency you will need to start a new satellite and transponder scan for the ASTRA satellite see Satellite Search If a factory reset is performed the information contained in the tvtv EPG is also deleted To restore the data required for the tvtv EPG you must run a satellite scan and then switch the receiver to standby mode to update the tvtw EPG data As soon as the tvtv disappears from the receiver display the tvtv EPG is updated Digital compatible single cable solutions such as Technisat DisiCon 4 LNB do not permit transmission of the tvtw EPG data because the necessary transponder 12 603 75 MHz symbol rate 22 MSymb s horizontal is not transmitted in that system This transponder must not be deleted as the twbw EPG data is transmitted on it The tvtv EPG data is buffered on the hard disk meaning the hard disk is running even during normal SAT reception lts running noise is much less than in recording or playback mode however In addition the hard disk emits a short noise every 10 minutes indicating an essential data balancing operation This is quite normal and does not need to concern you
87. tons to enter a new frequency appropriate for your system Use the OD buttons to select L O Low and do the same Press four times to exit the menu This saves the set value If you make an incorrect setting you will see the following message Weak signal or no signal The factory setting is On Under normal circumstances the supply voltage should be turned on If your receiver is connected to a multi feed antenna which is aligned with the HotBird satellites for example you must change the receiver settings for the DiSEqC signal This also applies to other satellites as well of course DiSEqC Digital Satellite Equipment Control Different control signals are required to select the satellite signals To date the LNB supply voltage of 14 18 V and the 22 kHz signal superimposed on the LNB supply voltage have been sufficient for signal selection for most applications These four switching signals allow you to switch between the horizontally and vertically polarised signals and between two satellites multi feed reception To extend the frequency range to the 12 GHz range high band or for reception from more than two satellites additional control signals are required for LNB actuation and signal selection The DiSEqC signal is responsible for this This is a special modulation of the existing 22 kHz signal 73 Installation Menu DiSEqC Setting The precondition for this setting is that you have not made
88. trol buttons To delete a recording access the HD programme guide by pressing the gt button Use the OD buttons to select the recording you want to delete and press the blue m button You will then be asked if you really want to delete the recording Confirm with or press to cancel A deleted recording cannot be retrieved Recordings cannot be deleted during recording Audio Settings Setting the Volume Muting Set the required volume level by pressing the E button on the remote control of the receiver A bar indicator is displayed on the screen to show the set volume Press to mute the sound A red bar indicator appears Press the button again to restore the sound Stereo and Two Channel Sound Playback Be sure to follow the instructions in the manual for your Dolby Digital system Use the yellow button to open the Audio menu for sound and language selection where you can make the desired settings e g subtitles language selection soundtrack audio mode digital output MPEG stereo AC 3 as long as they are included in the reception signal Clear skip points Split take 9 Bayerisches F b Stereo Select the menu options using the y buttons and make the desired setting using the gt buttons Press the yellow 8 button again to exit the menu Possible audio settings include Soundtrack 1 0f2 20f2 Audio mode Stereo Mono left or right Digital Output MPEG stereo D
89. unctions or total loss of the operating system software may occur On no account may the receivers be switched off or the connection interrupted during data transfer This may result in data loss malfunctions or total failure of the operating system Always wait until the Succ or F message appears on the display Technical Appendix Technical Features The twin Sat receiver UFD 580 has two separate reception and signal processing paths This allows you to record a programme and simultaneously zap through other programmes or to record two different programmes and at the same time watch one of them either live or time shifted or another previously recorded programme The following functions are also available Reception of digital TV and radio programmes Common Interface for two CA modules for Pay TV not included Suitable for software updating via satellite or RS232 port PIP Picture in Picture optional access across all channels One touch recording Time shift recording Loop through Sat IF input Videotext Teletext processing internal and via TV set 4000 programme memory slots Satellite input frequency range from 2 x 950 MHz to 2150 MHz tvtvEPG Electronic Programme Guide with timer function USB 2 0 port for hard disk data download PC software available from http www kathrein de esc kathrein download ufd firmware_ufd580 cfm Mains switch with mains power isolation Automatic date and time setting via
90. vanced day by day selected using the GP DVR also note that most digital buttons a OI ea eS e Start time advanced minute by minute selected using the IL buttons or entered directly using the number pad This means you must programme your external video e End time advanced minute by minute selected using the recorder or DVR in line with the IL buttons or entered directly using the number pad timer record settings e Recording on hard disk or external recorder e g video recorder selected using the buttons In user defined recording you can use the buttons to move to the various days of the week and press to activate and deactivate them Note The timer data and settings of a programmed recording cannot be altered once entered To change a timer entry you must delete it and create a new one Press ox to save the selected recording data Example of user defined recording Tuesday 05 04 2005 9 08 32 Search Tus 05 04 KABEL 20 16 22 55 Jerry Maguire Spiel des Lebens OK Plan recording 36 TVTV EPG and Timer Example of series recording Note Timer List Tuesday 05 04 2005 08 33 Tue 05 04 KABEL 20 16 22 55 Jerry Maguire Spiel des Lebens Recording Series recording All upcoming episodes will be recorded on hard disk OX Plan recording If every edition or episode of a series is programmed to be recorded using the Serie
91. y pressing the power switch The data ports of the two receivers are interconnected by a zero modem cable The master is then switched on again Simultaneously press left arrow button and SELECT under the front flap of the master to transfer the programme list The slave can now be switched on The transfer begins During downloading the display of the master shows t001 t002 t00n while the slave correspondingly shows r001 r002 r00n The LED displays during the block transfer If both receivers indicate Succ the download was successful Operating System Software Download 86 The procedure for downloading the operating system software is the same as that described above Start the transfer of the operating system software by simultaneously pressing 3 right arrow button and SELECT under the front flap of the master During downloading the display of the master shows t001 t002 t00n while the slave correspondingly shows r001 r002 r00n The LED displays during the block transfer If both receivers indicate Succ the download was successful If any problems occur in transmission the master display will show F with representing a numerical value In such cases check the cable connection and retry The receiver to receiver data exchange as described above must only be carried out between devices of the same type otherwise malf

Download Pdf Manuals

Related Search

Related Contents

programa mano VIIème ÉDITION DU FESTIVAL DE THÉÂTRE    3Com 2816-SFP Plus (3C16485) Switch User Manual  Bedienungsanleitung  371 SPL Computer    fulltext - DiVA Portal  Disponible sur le site de l`observatoire : http://www.uqo.ca/observer  Manual de Usuario Serie S  31-709型 取扱説明書 全自動タイプ ガスふろ給湯器  

Copyright © All rights reserved. Failed to retrieve file