Home

Kathrein UFD 170 User's Manual

Contents

1. Turntable Unit Software Download Do not turn off the system during the download The next message you see will be HDP Programme Sending The software is transferred to the control unit in the UFD 170 For safety reasons two software versions are saved so that if one version fails or if there is a download error an alternative software version will be available for operation of the turntable The oldest versi on white text is always overwritten automatically 13 Manual Lowering to Park Position Safety Instructions N gt In case of a defect in the electronic control the flat antenna can be returned to park position horizontal position manually You can drive to the nearest workshop with the extended anten na at a moderate speed but take into account the added vehicle height Therefore manual lowering is recommended Users who are not familiar with the necessary repair work are urged not to manually lower the antenna into park position themselves They should contact an engineer or mechanic A suitable person may be available at the campsite In any case the safety instructions listed below must be followed It must be ensured that The antenna and equipment connected to it are disconnected from the power supply The person carrying out the repairs does not suffer from vertigo and can move around safely on the roof of the caravan or motorhome The person carrying out the repairs is wearing
2. You can make the settings using the A keys or the number keys Note that incorrect time settings may be rejected and leading zeroes e g 07 15 must be entered when entering the time The current time is shown under Start time which you can then change If nothing else is entered the end time is automatically set to the same date and one hour after the start time At the end confirm your settings by pressing D Or three times Timer Settings Note If you have pre programmed an On Air Download software or channel list download using the timer all subsequent timer settings are ignored after a successful download VPS Signal Note that most channels do not include a VPS signal in their digital TV signals You must therefore always program your video or DVD recorder to match the timer settings 29 Audio Settings Setting the Volume Use the 1 keys on the UFD 170 remote control to set the desired volume on the receiver A bar is shown which indicates the set volume Stereo and Two Channel Sound Playback The set sound playback method can be seen from the channel message which you can view using the key depending on the alignment of the sound wave symbols a Astra 1 Bayerisches F The alignment ofthe sound wave symbols shows the setting mono left sound waves point to the left mono right sound waves point to the right or stereo sound waves point in both directions The first of the t
3. Gl Paepumg NETT T 00 X 00 po 9KENEAE ION Spo YES ETERNA yinuizy TO eae uong sn 1713 HER yoo dau nua daH 9Iqge e JON LONE MIL M M J9plAO4d UDISAJA ZH IIS 49plA04d UDISAJA adejJa u UOWWO mrq amp ua e dneg ewueyuy JOH eseou LOLLO e amp en amp ue uoneyejsul nua ure Aad TEN MM peojumog BFS d H peoumog ay uo 195 40 284 ames OANIIPISIQ UBIS UIPI dl UBIS FUNPIES dnjag suusjuy uonejejsu enDue 9 UNS ogey 129dsy 1 hir 9dALAL DO arem Gunes IQ ET wu 18907 Zu ea VET ee UO BUNOZU ETT 70M o41u02 JE1us48d SIDJOWICICY Ul9 sAS y Buisn pojooejes s b n Aue ney jou seop uodo nusw eDenDue eu S 9 OJON 91JnjonJgjs nuayy Initial Setup Important Information Getting Started 16 Before setting up the system make sure that it has been mounted installed and connected properly as described in the installation manual and the safety instructions Connect the unit to the power supply Turn on the receiver using the power switch on the front The unit is then in standby mode Turn on the receiver with the key on the remote control Your UFD 170 welcomes you The following OSD then appears The turntable then searches for the factory preset programme In this case this is Das Erste on the ASTRA satellite The follow
4. Qual bars on the left hand side The higher the bar the stronger and better quality the signal received At the same time you can use the key to activate a search tone the level of which corresponds to the signal strength The graphical display in the lower section of the screen green with red dot represents the relative position of the antenna While the antenna turntable is moving in the desired direction a cor responding message for Elevation and Azimuth direction appears ex ample 65 Alignment Satellite Search The new co ordinates are not After successfully correcting the settings use the Ipfe Ww keys to assigned to the satellite until you have saved the satellite position move to Save and confirm with in the HDP menu You can use the D key to exit the menu 66 Change of Location After a change of location the antenna moves to the last position selected After initialisation you will therefore see the following display example as it depends on the position last selected For slight changes of location the antenna can find the satellite very quickly If no signal is found at the last position the following message appears ii DO SHTICOH e jal GNATI Ch LORK un ea maurs PE SSS u R n LU SEOI LII ele SEARCH MODE EXT Uy If you still want to aim at the satellite press to start the search HDP Antenna i35 searching Astra Please wait max 3809 8 S
5. You can find out which Smartcard is located in the CA module using the Common Interface menu which you can reach from the main menu 25 Common Interface The illustrations below depend on the specific module and Smartcard and are therefore only examples Common Interface Version DVB_CI_V1 00 Provider SkyCrypt Slot 2 Version Not available Provider Not available i OW Next FE Prev The key takes you to the menu generated by the CA module SkyCrypt Cl module FEX Firmware v2 26 Current CA is 1 ALL From this menu your card and your PIN code allow you to access various programmes from your pay TV provider AstonCrypt has been selected as an example here The details can be different for each CA module Always follow the instructions supplied by your pay TV provider Note The displays appear in English even if you have selected German as the menu language 26 Common Interface Information for Conax SECA Viaccess and CryptoWorks Users Note that with monthly activation intervals the programme providers have different procedures for activating pay TV cards Activation may therefore be a few days before or after the beginning of a new month During this activation period the CA module and Smartcard must be in the Cl slot and the receiver must be turned on a set to the booked pay TV channel Follow the pay TV provider s instructions For monthly subscription extensions the Smartcard
6. Alphanumeric Assignment of Remote Control Number Keys section KRY Channel List Lotra 36 GHz t3l 18V MSPS iD Favorite 2 Favorite 3 avorite 4 Favorite 5 OW Select M W Exit Rename You can now use the 4p qw keys to switch to the other favourite lists and rename them with and the number keys Pressing D twice saves the new name and takes you back to the channel list first then to the normal TV screen Managing Channel List Channels Selecting a Favourite Channel from a Favourite List Undoing Favourite Selection To select a favourite channel from one of the five favourite lists you must first press the Qo key for the channel list and then for the mode The following screen appears RV Channel List Free Scrambled e Satellite Astra SR WDR K ln V ow iw ADD BR alpha MOVE R MODE OW Select PE T Exit You can now use the 1 keys to switch between the available favourite lists and select the desired list with Q9 Use the ep 44 keys to select the desired channel which is highlighted with a coloured bar and shown on the screen in the top right hand corner Pressing shows your selected favourite channel on the normal TV screen To delete a favourite channel from one of the five favourites lists you must first press to open the channel list and then press to select the channel list mode Select the desired favourite list with the cursor keys and confirm wi
7. Astra ZDF 1318 EAU EN Wunderbare Welt Die Tig 13 15 14 00 NT cR You can permantly show or hide this information bar by pressing the key repeatedly For encrypted programmes you will see the following message 1 Astra 18 ORFI Bie Ski FIS Weltcup Riesent 12 55 14 08 You can only receive these programmes with the UFD 170 in conjunction with a CA module and the appropriate pay TV card Smartcard Programme Selection TV Radio Channel List An alternative method of selecting a different programme is to press the key which opens the channel list RV Channel List All List Astra 91 11 836 GHz ZDF Horizontal 18V SAT 1 27500 MSPS RTL Televisio ARD RTL2 z Super RTL FAV DEL VOX LOCK M ADD ProSieben G MOVE R MODE NE gt Page Up On OK Watch 7 Exit 0 9 Move At the top left is a for the complete list In the column below it you will see details of the channel name the channel number and whether the programme is a favourite locked or encrypted In the upper right hand column you find details of the satellites recei ved the transponder and its frequency its polarisation and the symbol rate In the lower right hand column you will find the Programme Channel Settings menu The factory settings for programmes and channels can be changed here Pressing the Favourite saves the channel shown as a favourite channel Lock locks the channel
8. GHz ZDF Horizot tal 18V 27 500 MSPS RTL Televisio RTL2 Super RTL VOX ProSieben EET NEUE Watch P Ae 39 Managing Channel List Channels Sorting Channels Deleting Channels Take care when deleting channels Deleted channels are permanently deleted and can only be retrieved by carrying out a new satellite search 40 You can sort the channels to meet your own requirements Sorting involves moving channels in the channel list The key takes you to the channel list Use the P 4 and the keys to select the channel you want to move Press to release the channel to be moved from its current position text colour of selected channel changes Nee RY Channel List E oum gt gt E All List Astra 14 12 188 GHz Hor zont al 18V Das Erste ZDF SAT 1 27 500 MSPS RTL Televisio RTL Wald TU GE VOR F TV super RTL FAY DEL VOX LOCK M ADD ProSieben MOVE R MODE NA TE Page Up On Ok Watch 1 Be O 9 Hm You can then use the qw and the 1 keys to move to the desi red position and press to drop the channel at the new location You receive a confirmation that the changes have been saved and the channel moved appears on the screen The key takes you to the channel list Use the 4p qw and the keys to select the channel you want to delete Press and the control programme asks you Press to confirm that you want to delete the selected ch
9. Mute Press on the remote control The sound is turned off The following display appears on the screen Press again to turn the sound back on The normal volume display bar appears for a short time Although you can change the programme while the sound is muted the sound is only reactivated if you cancel mute mode by pressing or adjusting the volume 31 Programme Overview EPG EPG Electronic Programme Guide The EPG gives you an overview of the programmes broad cast on the current transponder you are receiving including their time and duration You can only receive this data if the programmes are broadcast with an Electronic Programme Guide EPG e g programmes from ARD and ZDF Program Guide Current Next 0938L 9 KABHI 10 DSF ee fl BayerischesF Fliege Ole T 7 12 Hr fernsehen add 13 SR Fernsehen 14 SUDWEST BW f 16 BR alpha Anna Sonmi zj DN Gurrent Nert F Schedule Extended The left hand column shows the channel number and name and the current programme The right hand column shows a shortened form of the programme title and a progress bar with the start and end time of the currently selected programme In the left hand column you can use the 4p ww keys to switch vertically between the programmes and the keys to switch horizontally The key switches to the new programme selected The key displays additional information on the current programme
10. Program Guide TE Extended oai Jo und geine Freunde sindGel ndewagen Fr na SUDWEST Bw eaks AmWoohenende zieht es den 12 01 2005 10 45 100 ut H _ v d D zseldorferauf die offiziellen Streifzude OFF Road Pisten a ee VE HEX Current Next Schedule amp Extended F Page Up On 32 Programme Overview EPG Within the programme overview the Q key displays a list showing the next programmes on the currently selected channel with their time and duration if transmitted in the EPG The length of the programme list depends on the relevant programme provider and can cover several days EPG Timer Programming You can use the 9 keys to move the coloured bar in the list and select a programme for timer programming The key selects the timer Here you can use the t keys to select various timer settings e g whether the relevant programme is to be recorded once daily or wee kly The key transfers your selection to the timer pressing the D key twice cancels the operation 33 Managing Channel List Channels The channel programme settings made in the factory can be changed in the Programme List menu The menu is opened using the key in TV or Y mode A channel is selected using the gt p and Q9 If a password has been saved you must also enter it to continue keys Confirm your selection with vy 2l pP o SEM RV Chann
11. Rename You can use the 4p qs keys to select from your five favourite list those lists in which you want to save your favourite channel You can save several different channels in a list The UFD 170 thus allows several family members to save their preferred channels and to select them conveniently at all times Entering a password allows you to protect the channels against unauthorised use see Password section The currently selected list is highlighted with a coloured bar You can then press the key to mark the selected channel with the apple icon The next programme from the programme list is automatically selected and appears on the small screen in the top right hand corner You can then mark your next favourite programme with the apple icon 35 Managing Channel List Channels Renaming the Favourite Lists 36 You can give the individual favourite lists the names of your choice e g Sport to group together all channels that broadcast sport However you can alternatively use the names of the different users e g Mum Dad etc Use the key to switch to the channel list and press Q Use the cursor keys to switch to the favourite list that you want to rena me Pressing highlights the first letter in black You can now use the number keys to rename the favourites list Use the i keys to switch between the different characters For details of which letters are assigned to which number key refer to the
12. can be re initialised using the CAM Re initialisation CAM menu lf your Smartcard is not activated despite following these instructions we recommend that you briefly remove the CA module and Smartcard while the receiver is turned on and re insert it This information has nothing to do with the properties of the unit it is merely intended to assist you 2f Timer Settings Do not forget the Status setting 28 You can use the timer to ensure that a programme is recorded at the correct time with a video or DVD recorder A total of 14 timers are provided which you can set to different programmes or start end times To access the Timer menu from the main menu press use the 4p 4 keys to select System Parameters then press use lt to go to Local Time Timer and press again The following display appears example 11 01 2005 14 14 CH Type Timer 2 CH Number 2 Timer 3 CH Name ZDF Timer 4 Start Time TWOV2005 14 16 Timer 5 Stop Time 11 01 2005 15 16 Timer 6 Status No Timer 7 i OW Edit M Main T Prev Use the V p keys to move the cursor to the desired timer and confirm with Q9 Press D to exit the timer You can now make the following settings Channel types TV radio or On Air Download Channel number channel name is shown automatically Start time date and time Stop time date and time Timer status no once daily weekly
13. current time The in the third line stands for the programme selection from the overall list when selecting from favourites list an apple symbol appears instead of the This is followed by the programme title and the start and end times of the current programme if this data is broadcast by the programme provider The message for the set radio channel has the same layout A radio unit symbol in the top left hand corner indicates that it is a radio channel Broadcast times and text are only shown if these are transmitted by the radio broadcaster PA information 1 Das Erste MEME 30 11 Aus heiterem Himmel 09 05 09 55 Weak or no signal indicates that an error has occurred in the receiving system or in the receiver settings or that the transponder is not sending The channel message then shows a satellite antenna instead of the Z Check the SAT IF connection and the LNB configuration The list of service settings at the end of this manual can be used to help you do this Video Text x This symbol in the programme display shows you whether video text is broadcast for the selected programme When you press the key the receiver processes the broadcast video text including for encrypted signals for your TV set The following display appears for a short time During a search the programme page you are searching for here P100 is shown in the top left hand corner and the current time is sh
14. favourites Programme overview EPG programme guide Locks a channel Programme list Programme information Help cursor keys Programme selection Select sub menus and menu options Mute on off Numerical input for programmes Child protection LO frequency etc Select video text Power on Power off Standby Select main menu Adds a new channel Last programme EXIT Locks a channel Scart connection setting radio OFF deletes a channel cursor keys Volume Menu options change page to EPG or channel list Confirm sub menus and menu options Radio ON OFF Select mode for programme list Audio frequency menu Language selection Moves a channel to a different position Controls Displays and Connections Important information on the remote control You can only operate the UFD 170 using the remote control RC 400 supplied Without the remote control it is not possible to set up or control the receiver and the turntable Therefore you should always take good care of your remote control and make sure you have spare batteries for it Remote control instruction sets The remote control has two instruction sets This alllows you to operate two receivers independently of one another in the same room Note This does not work in conjunction with a twin receiver To use this feature program the first receiver to instruction set 1 and the second to instruction set 2 First turn on receiver
15. receiver then begins the update process If your receiver is already up to date a message appears on the screen to notify you of this Once the update is complete the receiver is re initialised and starts operation again In case of an error or no signal the message Download failed appears Never turn off the receiver during the update process as otherwise you could lose the entire software It will then need to be re installed in a workshop or using a PC and null modem cable During the download Please wait flashes on the screen Follow all on screen instructions After a software update you must reset the clock and check whether the HDP Antenna Setup menu option in the main menu is set to On If not set the selection to On using the cursor keys as otherwise you will not be able to operate or actuate the turntable You can also download the updates from the Internet The address is http www kathrein de First click on Service and then on Software and Download Select Receiver The page provides instructions for the procedure Connection Diagram 10 9V 13 8V Ignition 3 mm umm m mm ee ee San y POSITIONER ene VIDEO e i 5 d M POWER n POWER our e n Mna ge 10 9 13 8V 10A 10 9 13 8V 3 FOUT Receiver TS LU QU US Fe Fe U UL UU 7 DIGITAL Pe WAGON 3345 a AUDIO NN ONS NS cs
16. 1 and then receiver 2 using the power switch Hold down the key Enter 901 using the number keys To transfer the code switch receiver 1 to standby with Q and then turn the unit off with the power switch Start up receiver 2 again Hold down the key Enter 902 using the number keys To transfer the code switch receiver 2 to standby with Q and then turn it back on Start up receiver 1 again Hold down the key Enter 903 using the number keys For the first two settings the remote control must be pointed at the relevant receiver turned on You can now use the key to change between the two instruction sets A and B toggle function and operate the two receivers alternately As supplied instruction set 1 is always activated by default If you are only operating one receiver and the active instruction set is accidentally changed so that you can no longer operate the receiver the remote control can be switched back to instruction set 1 with no problems This procedure is described above 12 Operating Instructions Menu Concept Note The bar at the lower edge of the screen provides information on each menu option Language Selection The structure of the menu concept is based on logical operating sequences In TV mode the currently selected programme always appears in the upper right hand corner of the screen in radio mode a black background is shown The selected menus
17. Child Protection Locking a Channel Setting System Parameters Child Protection system Information Local Time Timer TV Type Picture Format Screen A V Mode Installation Menu Opening the Installation Menu LNB Configuration L O Oscillator Frequency Operation Standby DiISEqC 1 Setting DiSEqC 2 Setting Antenna Setup Satellite Search a ing Seales for Deleting Transponders DiSEqC M UFO Setup 22 kHz Signal Tone Burst and DisEqc M Signal DisEqc M DisEqC M Repeat UFO mini Remote Frequency UFO micro Factory Settings Software and Programme List Update Connection Diagram SAT ZF Connection On Board Network Connection Control Cable Important Information on the Turntable before Setup Remote Control Initial Setup Information Contents Alignment Satellite Search Manual Correction Change of Location Reset Park Reset Park Special Messages for Turntable System Protection Messages Satellite Lost Limit Reached Turntable Unit Software Download Manual Lowering to Park Position Safety Instructions Manual Retraction Service Glossary Brief Technical Glossary Safety Instructions and Important Information DANGER d WARNING This page contains important information on the operation installation location and connection of the unit Read these instructions carefully before setting up the unit Power supply cable Make sure that the power supply cable is not d
18. Help for the selected item is available by pressing the key Press the key again to exit the Help menu You may need to correct the Summer time setting Use the a2 keys to go to the day light savings time option Here you can use the a keys to turn this time setting on or off Note TV Type Picture Format 48 With the factory setting the receiver indicates the UTC United Time Coordinate previously Greenwich Mean Time which is transmitted with the data stream For Germany the time must therefore be correc ted by 1 hour To do this move the cursor bar to the TH Time Timer menu option using the 8 key You can use the keys to correct the time for wards or backwards in half hourly intervals If the time displayed by the receiver differs from the correct time by just a few minutes proceed as follows Use the gw p keys to go to the Local Time Timer menu W and change the time by approx 10 hours forwards using the keys Then first press to switch the receiver to Standby mode and disconnectit briefly from the power supply for a few seconds using the power switch Start up the receiver again and from the main menu switch to the System Parameters sub menu and then to the Local Time Timer option If necessary correct the time in half hourly intervals with the 1 keys until the correct time is displayed Pressing twice takes you back to the normal TV pict
19. Interface a standardised interface Encryption device for pay TV programmes Control system between receiver and LNB or multi switch See Technical glossary Digital Video Broadcasting Power density per unit of information Digital signal to noise ratio Vertical alignment of the antenna Electronic Programme Guide Colour picture blanking synchronisation combined basic band signal composite colour signal Display on receiver Low Noise Block Converter Muting of sound On Screen Display See Installation menu Oscillator frequency L O Analogue TV standard Pay per view TV channels e g ORF Free X TV Standard for internal decoder interface for pay TV Personal Identification Number Satellite receiver Video signal made up of three individual colour signals red green blue Receiver input signal 21 pin connecting cable Standby mode Super Video Home System video recorder standard Transmitted data rate of satellite signal Clock function for pre programmed switch on and off times See Technical glossary Video recorded connection See Technical glossary S VHS signal luminance chrominance 71 Brief Technical Glossary DiSEqc DiSEqC components Dolby Digital DVB MPEG 2 Eb No ratio FEC PID 18 DISEqC Digital Satellite Equipment Control is a communication system between a satellite receiver master and the peripheral satellite components slaves such as LNBs multi switches rotati
20. Operating Manual UFD 170 DVB S Receiver and Turntable KATHREIN C 4 UFD 170 20210063 KATHREIN Antennen Electronic Foreword Internet E mail Dear customer This operating manual is intended to assist you in making optimum use of the comprehensive functions of your new DVB combi receiver and the turntable We have tried to make the operating instructions as easy as possible to understand and to keep them as concise as possible To help you understand particular specialist terms that cannot be translated we have added a short glossary at the end of the manual The power switch is an environmentally friendly feature If you will not be watching the television for a longer period you should therefore disconnect your equipment from the power supply to save energy For shorter breaks you can switch the equipment to standby on the remote control which uses only a minimal amount of energy We hope you will have a good reception and gain a lot of enjoyment from your new DVB caravan receiver and automatic positioner Your KATHREIN Team If you should experience any unexpected problems with your UFD 170 turntable please contact your specialist dealer or our hotline KATHREIN Werke KG ESC Electronic Service Chiemgau Technical Customer Support Factory repair centre Tel 49 0 8031 184700 Tel 49 0 8641 9545 0 Fax 49 0 8031 184676 Fax 49 0 8641 9445 35 36 www kathrein de www esc kathrein de tech
21. adio signals A satellite has several transponders Analogue transponders transmit only one TV programme and possibly several radio programmes at the transmission frequency Digital transponders simultaneously transmit several TV and several radio programmes at a transmission frequency If a programme provider is broadcasting several TV programmes via a digital transponder we refer to the providers programme package The terms digital transponder and programme package have the same meaning The video bit rate describes the quantity of data from the digitised video signal that is transmitted per second The Viterbi rate code rate error rate characterises the error protection used by the programme provider The DVB standard provides the following values 1 2 2 3 3 4 5 6 7 8 79 Internet http www kathrein de KATHREIN Werke KG Anton Kathrein Stra e 1 3 PO Box 10 04 44 D 83004 Rosenheim Germany Telephone 49 80 31 1 84 0 Fax 49 80 31 1 84 3 06 936 2705 B 0505 ZWT Subject to technical changes
22. amaged Units with a damaged power supply cable must be disconnected from the power supply and repaired by a qualified engineer before setup Risk of death due to electric shock Fuse in cable and receiver Removing or bridging the fuse in the cable or the receiver is prohibited A defective fuse should only be replaced by a fuse with the same rated value Risk of fire due to short circuit Cleaning Disconnect the unit from the power supply before cleaning it Only use a dry cloth for cleaning and only clean the outer surface Never open the unit Touching the parts inside the unit carries a risk of death due to electric shock Playing children Make sure that children do not push any objects into the ventilation slots Risk of death due to electric shock Earthing The antenna system must be earthed as specified or equipotentially bonded The requirements of EN 60728 11 and any national regulations must be met Danger due to surge voltages lightning strikes Mains voltage Only operate the unit at the specified mains voltage indicated on the rear of the unit or on the external power pack The unit may only be connected to the mains and turned on once it has been connected to the antenna and to the TV set or the cable network and PC If the mains voltage is too high there is a risk of fire Vehicle height Risk of accidents due to exceeding normal vehicle height by failure to lower antenna The driver is responsible for the c
23. an access your channels at all times even if you have forgotten the password Password Factory Setting The password is set to 0000 in the factory and is inactive Setting the Password and Child Protection 44 Press the key on the remote control to call up the main menu Use the 4 amp 2 keys to go to the System Parameters menu and confirm with 9 Use the a2 keys to select the Child Protection menu option and confirm with you may be asked for your password which you must then enter The following screen appears Parental Control Lock Channel Editing Lock Installation New Password Verify Password Personal You can now make your settings with the u amp 2 and the 1 keys The following settings are possible Age limit This setting is only effective if the corresponding locking signals are broadcast Lock lists Yes No This locks the editing function for the programme lists Lock installation Yes No This locks the access to the installation menu Password and Child Protection New password You can enter your new password here using the number keys Confirm password You can enter your new password a second time here for confirmation Personal Enter the unit identification that the unit will report when turned on here This can be useful to identify the unit in case of theft For details of how to use the number keys on the remote control for alphanumeric entries refe
24. and or the receiver settings If this only affects individual programme slots there may be an interrupted signal from the broadcaster or a fault in the reception system This message appears when HDP mode is deactivated Press to switch to the main First of all check the connection configuration and whether the default receiver settings are correct for your system In case of doubt consult a specialist engineer menu and then use the guy P keys to call up the HDP nna Se Fi tup sub menu Use the keys to change the selection to On Pres sing the keys takes you back to the normal TV screen Receiver Factory Satellite Setting Your receiver is factory set up for the satellites listed in the following table You do not normally need to make any additional settings ASTRA EUTELSAT EUTELSAT 19 East ne 10 East 16 East TurkSat Telecom Telecom ASTRA 28 2 42 East 5 East East EURO EURASIA AtlanticBird 3 Fast BIRD 28 5 Amos 4 West Thor 1 West Sirius 5 East Arabsat Intelsat 707 26 East Telestar12 Hisparsat EUTELSAT 15 West 30 West 7 East 18 On Screen Display OSD General Help Function The bar at the lower edge of the screen provides information about each menu option The receiver functions are controlled by a microprocessor and comprehensive software The explanations below are intended to help you understand all the processes and t
25. annel The programme on the next channel is then shown in the top right The changes are saved when you exit the channel list Managing Channel List Channels Adding Channels Manually Attention This function is only required for channels that are not broadcast to the DVB standard All channels that comply with the standard are recognised and saved by the automatic search Attention You can only select satellites that are available in the installation menu Attention Never change the PID information without good reason as they affect idenfication of the reception signal Pressing the key takes you to the channel list Press to display the following screen Add Digital Channel TP Frequency Polarization Symbol Rate CH Name Video PID Audio PID PCR PID UNES Prev You can make the entries for the new channel here The first line in the list is highlighted with a coloured bar You can use the 4p qw keys to move the bar to the desired item Make the desired settings or entries using the ber keys You can set keys and the num The satellite received The transponder and the transponder frequency The polarisation The symbol rate The following items Name Video PID Programme Identification Audio PID PCR PID Programme Clock Reference will only accept alphanumeric or decimal entries Pressing the key takes you back to the channel list You
26. ansmission frequencies are located in the following ranges 10 7 11 7 GHz 11 7 12 75 GHz Low band High band Installation Menu Changing the Oscillator Frequency Operation Standby However the input frequency range for the receiver is in the range 950 to 1250 MHz The high frequencies are therefore converted into a lower frequency using the oscillator frequency LO frequency L O local oscillator LNB local oscillator Different oscillator frequencies are used for the conversion depending on the satellite frequency range and the system type For ASTRA and EUTELSAT receiving systems this is normally 9 75 GHz 9 750 MHz for the lower frequency range low band and 10 6 GHz 10 600 MHz for the upper frequency range high band Older receiving systems still use a 10 GHz oscillator frequency in the low band range which usually are not suitable for digital reception The receiver generates the frequency to which it needs to adjust by subtracting the oscillator frequency from the satellite transmission frequency saved for each programme You only have to set the oscillator frequency used by your reception system Before chancing the LO frequency you must therefore ascertain whether this is actually necessary The oscillator frequencies listed in the text above are set in the factory Use the key to switch to the LNB Configuration Menu on the right hand side The setting for L O High is highlighted in col
27. as they are factory settings or operating settings that are tailored to your receiving system New settings are only required if the reception system is changed or expanded Opening the Installation Menu LNB Configuration Note L O Oscillator Frequency 50 You reach the installation menu from the main menu called up with the key by using the 4E 44 keys to navigate to Installation Menu and then pressing the key to open If the UFD 170 is being operated in conjunction with the Kathrein turntable nothing may be changed in the LNB Configuration menu Changes to these settings would result in the assignment being lost and the turntable would not longer be able to find the satellites Use the 4p 4 keys and the key to select the LNB Configuration option Before every change you should note the settings on the form at the end of the operating manual The satellites listed under the Receiver Factory Satellite Settings option are preset in the factory LNB Configuration HotBird EutelSat 10E EutelSat 16E TurkSat 42E Telecom 5W Telecom 8W ASTRA28 Position High L O Low L O Power Stand By DisSEqC 1 4 DiSEqC 20 i Page Up On 0 Edit Satellite receiver systems consist of a parabolic antenna attached to the actual receiving system LNB or LNC which converts the RF signal from the satellite into a lower frequency which can be processed by a satellite receiver The satellite tr
28. ating manual and follow them when handling the UFD 170 and the turntable All settings on the UFD 170 are made using the remote control Before setting up your satellite system make sure that the location allows a free view to the satellite positions to the South and is not shadowed by trees or other obstructions This will save you time and effort n T te ARE 3 MobiSat Yan Re ae t zm r t ae gon i En m E awe Pans mu gos ATI A a e s Refer to the Initial Setup section in the receiver section of this manual 63 Alignment Satellite Search If the vehicle is not on supports during the search process and people are moving around inside it there is a risk that the satelli te is not found due to the move ments of the vehicle If the satellite is found it is saved by the turntable and no search is necessary the next time the programme is selected 64 The antenna is aligned automatically After turning on the UFD 170 the turntable automatically moves to the last channel received and the associated satellite position e g ARD ASTRA This works because every satellite emits its own identification signal which is automatically identified by the UFD 170 The satellite search is started when you select a channel If the turntable has not yet saved the position of the satellite you will see the
29. ching or it may not be found after the complete search time e g if the signal is weak at the edges of the footprint if there is movement in the vehicle or unfavourable reception conditions such as heavy rain and snow The following messages then appear Use the key to hide a message Choose a different channel for the same satellite The following screen appears 70 Special Messages for Turntable Note If this screen does not appear automatically you can call it up manually using the key Press to restart the search If the search is unsuccessful again e g due to very poor weather or because you are in a marginal area reset the search mode from Standard to Fine as described below Press to hide the current screen display Press in the main menu and then use the 4p 4 keys to switch to the HDP antenna setup option Then press to go to the HDP menu The 9 4q keys take you to the Search Mode option Change the selection from Standard to Fine using the a keys HDP Menu Sat Position Elevation Azimuth Reset Park NA Select M Main D Prev Reap Sound Omi OFF Pressing T twice takes you back to the normal screen Now press Q again followed by the key In Fine mode the search takes slightly longer as searching is now done at a lower speed and with a smaller search grid 71 Turntable Unit Software Download If the vehicle is not jacked up dur
30. creen goes dark after a few seconds However you can permanently show the channel message by pressing or hide it again by pressing the key again Common Interface Important Information A Always follow the operating instructions from your pay TV provider and the instructions supplied with the Smartcard and the CA module Smartcards and CA modules are not included with this product Contact the relevant pay TV provider if you are interested in subscribing to a pay TV channel You are responsible for the use of the Smartcard in the CA module Store your card and PIN code securely when not in use Inserting the Smartcard and the CA Module The Common Interface Cl on the UFD 170 is suitable for the use oftwo CA Conditional Access modules These two CI slots are located to the bottom right of the front of the unit CA module 2 is designed for the Smartcard chip contacts point upwards and towards socket strip and is then inserted into one of the two Cl slots 3 The Smartcard should be inserted into the CA module without exerting too much force This also applies to inser ting the CA module into the CI slot Do not use a lot of force and follow the instructions supplied with the Smartcard and the CA module To remove the module press the relevant eject button 2 When you turn on the receiver the following message appears ZDF 14 10 v2 heute in Deutschland 1400 14 15
31. der frequency P or number keys Polarisation using W or Symbol rate with the number keys Search mode for exclusively freely receivable or for free and encrypted channels with W or The bar chart shows the relative signal strength but is not an indicator of the quality of the reception system The search is started using under the Search option You will see the message Search active After completion of the search you will see the following message example 55 Installation Menu TP Edit Scan 776 mar GHz Hor 7 gt Lu 3 t oon PES A NE TE Page lip On 0 Watch mM ZU Pre Press the key to exit this menu and switch to the channel previously highlighted in colour The key takes you back to this menu where you can search for additional transponders After an unsuccessful search you will see the message Error All new channels are added to the end of the existing channel list The Delete TP option allows you to remove a transponder from the programme memory using the key If you delete a transponder all channels from that transponder are also automatically deleted from the channel list You are prompted to confirm before deleting DiISEqC UFO Setup DISEqCIUFO Setup DiSEgC DiSEqC Repeat UFO mini Remote Frequency UFO micro D M Main P Prev 56 Installation Menu You should only make changes in this menu if the receiver is connected to a diff
32. e Up Un OK Edit Press the key The following display appears which you should confirm with Q9 Adding Deleting Satellites Note Deleting Satellites You can now make entries corresponding to your receivi 1 ystem in the relevant positions using the cursor keys P En and the number keys For details of how you can change the satellite name using the number keys refer to the Alphanumeric Assignment of Remote Control Number Keys section LNB Configuration telatar12 HISPASAT EUTEL7 amos1 THOR SIRIUS ARABSAT High L O Low L O Power Stand By DISEqC 1 10 600 GHz 9 750 GHz ON OFF 1 DiSEqC 2 mer AE LES M T Prev For each point you can press the key to view a brief explanation As described under Setting Up Satellites switch to the LNB Configuration menu Use the 4p 4 keys to the cursor bar to the satellite you want to delete Press the key You will now be asked whether you are sure you want to delete the satellite and you can either confirm with or cancel with 43 Password and Child Protection Note You can use a password to lock your satellite receiver against unauthorised access by third parties This protects the receiver against changes to its reception settings by unauthorised persons At the same time you can activate a child protection function which locks selected programmes Store your password in a safe place so that you c
33. e antenna into park position horizontal position 6 Remove the M12 screw This replaces the rocker on the tapered shaft 7 Replace the M8 screw and tighten it 8 Replace the plastic cover Removing the rocker from the tapered shaft moves the position of the rocker zero point An authorised dealer should eliminate this defect and calibrate the rocker 9 Consult an authorised dealer 5 Service OSD language German TV type Multi PAL NTSC Picture format 4 3 16 9 AUTO FBAS AV mode Y C S VHS RGB comp co lour VHS Satellite 1 Satellite 2 Satellite 3 Satellite 4 Satellite High L O 1 9750 Low L O 2 10600 Operation Standby DiSEqC 1 DiSEqC 2 DiSEqC menu 22 kHz High Low Pos A B OFF Tone Burst High Low Pos A B Opt AB OFF DiSEqC ON OFF DiSEqC repeat 1 2 OFF UFO mini ON OFF UFO micro ON OFF Additional settings 16 Glossary Audio output AV programme slot Azimuth CA module CI Decoder DiSEqC Dolby Digital DVB Eb No Eb No ratio Elevation EPG FBAS LED display LNB Mute OSD Oscillator frequency L O PAL Pay TV PCMCIA PIN Receiver RGB SAT IF signal Scart cable Standby S VHS Symbol rate Timer function Transponder VCR Connection Viterbi rate YIG Sound output on the receiver Preferred programme slot on TV set for Scart input Horizontal alignment of the antenna Conditional Access module decryption decoder Common
34. ec STOP X If a signal is found the antenna automatically goes into the fine tuning mode max 90 seconds if signal is adequate the position is immediately saved HDP Antenna 19 gear ny re Please wait max Ws 14 Sec STOP J After a successful search the following message appears 5 14 x TET ac i er EL 67 Reset Park Reset Note 68 Press in the main menu and then use the P 4 keys to switch to the HDP antenna setup option Then press to go to the HDP menu HDP Menu Elevation x 7 1 Azimuth 1102 Reset Park Park Search Mode Standard 37 1 790 2 i _ O Select M Main T Prev Reep Sound On ore Use the 4pm E keys to go to the N option and keys Now press change the selection to Reset using the The following screen appears The antenna is reset and automatically moves to the park position A short message Antenna reset appears again Press D to exit the menu Before replacing individual components of the system e g recei ver the turntable should be moved to park position with Reset After the Reset all satellite positions previously saved in the UFD 170 control unit are deleted However the satellite data in the receiver component of the UFD 170 is retained Reset Park Park You have three options for parking the antenna 1 The antenna can be moved to the park position by pressing twice 2 Press Q to switc
35. eceiver in a processing system The return path of the coaxial cable is used for control and communication between the receiver and the Kathrein UFO micro system If the receiver is operated in a UFO micro receiving system the UFO micro menu option must be set to On The receiving system then assigns the receiver a special address upon installation so that it will recognise the control commands sent by the receiver to the receiving system for signal selection In this operating mode a remote frequency need not be set as it is specified by the UFO micro system with the addressing If the receiver is being used in a UFO micro receiving system for the first time the address previously assigned must be deleted This is done in the UFO micro menu option by selecting Reset using the and keys The receiver is then assigned the original factory setting It then needs to be set to On again The receiver receives its new address from the new system Default setting Off This item allows all parameters to be reset to the factory settings using the key The factory settings do not necessarily correspond to the settings required for your specific system After resetting you may need to make all settings again Installation Menu Software and Programme List Update After the Show Info request you will see an information screen which you can exit using the T key Due to the digita
36. el List A _ 4 30 Sin aa All List Astra 91 11 836 GHz Hor zontal 18V ZDF SAT 1 27 500 MSPS RTL Televisio ARD RTL2 z Super RTL FAV DEL VOX SO LOCK M ADD ProSieben NG MOVE R MODE PT ES we AE MAL ee ede ric o 9 Selecting the Last Programmes Received 34 Pressing the Q key displays the last four programmes received for at least 10 seconds on the screen regardless of whether they were radio rT These keys can then be used to select the relevant programme If you select this function the following screen appears example V The arrows shown correspond to the cursor keys KU P HILZ 13 N24 3 ANTENNE BAYER Pressing the Q key again or pressing the D key clears the dis play Managing Channel List Channels Favourite Channel Setting Up a Favourite Channel You can organise and sort your preferred channels TV and radio e g all English language channels programmes or those that broadcast with no commercial breaks These channels are marked with the apple icon in the TV and radio channel lists which you can ac cess by pressing in the respective modes Use the cur sor keys WV P in one of your five favourites lists and press The following display appears to select the channel you want to save AV Channel List MSPS RA Favorite 2 Favorite 3 TV DEL M ADD R MODE Favorite 4 Favorite 5 OR Select M 1 Exit Q
37. els included in the selected favourite list Under Satellite you can choose betwee received by your system using the keys or select All satellites To open up a channel list containing all channels from the the satellites currently selected satellites press 9 Under Alphabetical you can display all channels sorted by a particular letter e g P all channels sorted alphabetically ABC all channels starting with a number 0 9 sorted in ascending order an f by channels starting with special characters ETC Use ng keys to switch between the individual options and then make your selection with the key Managing Channel List Channels Complete Channel List The complete channel list maximum variety of programmes can be viewed using the following setting Press to switch to the channel list and then press Q Press the pe keys to go to the top option Free encrypted or Free only Use the keys to select Free encrypted Then use the 4p 4 keys to go to the You do not need to worry about the settings for the Favourites and Alphabetical options Satellite option With the keys select the All satellites option see illustration av wir SRI T An Alphabet WDR K ln BR alpha RAI 7 Select W T Exit Confirm with The complete channel list appears illustration below is only an example RV Channel List All List un Astra 191 11 836
38. erefore follow the description of the switching matrices or contact the engineer who installed the receiving system DiSEqC Repeat If the receiver is operated in a receiving system with two or more DiISEqC switching matrices connected in series cascaded the DiSEqC command must be repeated In this case set the DiSEqC Repeat menu option to 1 or 2 Default setting Off 9f Installation Menu UFO mini Remote Frequency UFO micro Reset does not delete the pre programming Factory Settings In a subscriber controlled processing system the input frequency of the receiver is a fixed setting The subscriber controlled processing system transmits the signals at this frequency The reception parameters for programme selection are communicated to the receiving system by a DISEqC command and set The setting that has to be selected depends on the design of the subscriber controlled processing system If you have set the UFO mini menu option to On use this menu option to make the setting from the transmission frequency For the transmission frequency to be set refer to the installation manual for the subscriber controlled processing system It is essential that you follow the instructions in the subscriber controlled processing system installation manual The setting for this menu option is also designed for operation of the r
39. erent receiving system with different properties or if changes have been made to the receiving system You should therefore carefully follow the instructions for your satellite system However before each change you should note the settings on the form at the end of this operating manual You reach the DiSEqC UFO Setup menu using the P 4 keys and the key in the Installation menu 22 kHz Signal This menu option is used to specify whether the 22 kHz signal is to be used to switch between the upper and lower frequency ranges for a satellite low high or between two satellite positions Tone Burst and DiSEqC Signal If more than four control criteria are requried in a receiving system a DiSEqC control signal is required Which of the setting options Tone Burst or DISEqC is required depends on the components of the receiving system You should therefore refer to the descriptions of the existing components switching matrices of the receiving system Switching states for setting Switching states for setting Switching states for setting 22 kHz Signal Pos A B and Tone Burst High Low Low Tone Burst 0 High Tone Burst 1 Tone Burst Pos 1 22 kHz Off Tone Burst Pos 2 22 kHz On If the receiver is connected to a DISEqC switching matrix set the menu option to On DiSEqc The switching criteria and the input assignment of the DiSEqC switching matrices must be observed You should th
40. following display when you select a channel example Press the button to start search mode The search lasts a maximum of 380 seconds You will first see the following message As soon as the turntable has found the correct satellite automatic fine tuning is carried out The search lasts a maximum of 90 seconds if the signal level is sufficient the satellite position is immediately saved by the turntable unit The screen may freeze during fine tuning this is determined by the system Alignment Satellite Search Manual Correction After successful fine tuning the following message appears for a few seconds The set position the satellite found is saved At the margins of the footprints of a satellite e g after a slight change of position it may be necessary for you to manually correct the setting not normally required It is also possible to manually correct the fine tuning Press in the main menu and then use the 4p 4 keys to switch to the HDP antenna setup option Then press to go to the HDP menu HDP Menu Elevation Az muth Reset Park Search Mode 37 1 i O8 Select M Main U Prev Reep Sound Inf You can correct the inclination and horizontal angle of the antenna using the Elevation and Azimuth direction settings To do this press the keys or enter a figure using the number keys and confirm with Check your settings by referring to the Level and
41. h to the main menu and use the 4x keys to select the HDP Antenna Setup option Pressing takes you to the HDP menu where you can use the P 4g keys to go to the Reset Park option Now press to park the antenna 3 When the ignition is operated the antenna automatically moves to the park position However for this to happen the green wire of the power supply cable must be connected to the ignition see Connection Diagram Follow all the instructions in the comprehensive installation manual for the CAP unit The antenna is moved to the park position and this is then confirmed 69 Special Messages for Turntable System Protection Messages The following messages are shown on the screen to protect your receiving system and the on board network If this message appears check the turntable and antenna to ascertain whether the system is blocked by an object e g a branch or whether the on board voltage is too low Proceed in the sequence shown above screen The following message indicates that the battery voltage has fallen below a minimum value and the battery needs to be recharged You can continue to operate the sytem but there may be communication errors between the UFD 170 and the turntable e g for satellite search The antenna should not be moved during recharging to prevent peak loads when turning on Satellite Lost Limit Reached In rare cases the satellite can be lost when sear
42. ing message then appears Press the key to start the search Initial Setup As soon as the turntable has found the correct satellite the automatic fine tuning is carried out The search lasts a maximum of 90 seconds if the signal level is sufficient the satellite position is immediately saved by the turntable The screen may freeze during the fine tuning this is determined by the system If the turntable finds the desired satellite and the associated programme the following message appears If the turntable is unable to find the desired satellite and the associated programme the following message appears press and start satellite search with a different program me of the same satellite and check whether there are any obstructions to the antenna s reception After a successful search you can select the factory preset TV and radio programmes using the SW 4g keys To change from TV pro grammes to radio programmes press Q Press to return to the TV programmes For details of how to save additional TV and radio programmes refer to the TV Radio Programme Lists section When you turn on the last reception status set is always activated Check the time for summer or winter time see Local 17 Initial Setup Time Timer section If the message Poor or no signal appears on the screen as well as the display for the last programme received check the installation of the system
43. ing the search process and people are moving around inside it the satellite is likely to be not found or the signal is likely to be lost due to the movements of the vehicle Never turn on the ignition during the download This could lead to interference malfunctions 72 faults or If new software is available for the turntable you can download it from the ASTRA system Press to switch to the main menu and then use the 4 ww the lt gt keys to select i Download option and then select HDP 170 using the cally keys to select the Installation menu Use keys The menu is opened automati On Air Download 9 11 836 GHz 27 500 MSPS Astra Hortzontal 18V Display info HDP SW1 HDP SW2 Info Text 0000 0000 i OR Select M Main E Prey The current transponder reception situation frequency symbol is displayed here rate polarisation satellite Use the mp key to select the position and make your settings with the keys You can decide whether you want to download the software from the satellite at the suggested position marked with Yes the saved versions are shown with four digits 0180 in the illustration and whether you want to receive the information text If you press at the Start position the system begins downloading the software The entire procedure takes a maximum of an hour The download is confirmed with the following message
44. ith inadequate ventilation Never cover the cooling slots on the unit No not place any objects on top of the unit and maintain at least 10 cm of free space above the unit so that the resulting heat can be dissipated properly Moisture sunlight heat The unit should be protected from moisture dripping water and spray Do not place the unit close to the heating or expose it to direct sunlight and do not operate it in damp locations Connection and Setup Connecting the Unit SAT IF Connection Receiving Requirements Receiving System Presets The following section is intended specifically for specialist dealers You only need to pay attention to this section if you are carrying out the installation yourself The Connection diagram section contains a sample configuration Do not connect the unit to the mains until all installation work has been properly carried out Refer to the information in the Safety instructions section If you will be using the UFD 170 in conjunction with a CAP 210 or CAP 310 from Kathrein the installation instructions for the relevant CAP unit must be followed during installation Connect the SAT IF input on the UFD 170 to the satellite receiving sys tem Use a coaxial cable with a standard F connector If the F connector is not yet fitted on the cable strip the insulation from the cable as shown in the following illustration and carefully twist the F connector onto the end
45. l for the CAP 210 310 The power supply cable supplied wires brown white green is connected directly to the battery battery strip before fuse The brown wire is connected to the white wire to and the green wire to the ignition behind the ignition lock so that it is under power as soon as the ignition is switched on Make sure that the 12 V earth and ignition wires cannot be interrupted by switches connected in series as this can disable the function for automatic lowering of the antenna The green connection is important as it is the only way to ensure that the turntable moves to park position when the ignition is switched on This prevents driving with the antenna extended If the supply voltage is too low the UFD 170 receiver displays the OSD message On board voltage too low If the on board voltage is too low other error messages can also appear e g Overload even though there is no overload The control cable for the turntable is connected to the UFD 170 see previous page Important Information on the Turntable before Setup A 4 Y Remote Control N d Initial Setup Information This section of the UFD 170 operating manu al for the turntable assumes that the UFD 170 and the turntable have been properly installed and connected as described in the installation and operating manuals If you have not yet done so read the safety instructions at the beginning of this oper
46. l technology you can carry out updates of thesoftwareandprogrammelistforyourreceiverviasatellite The Software Download sub menu tells you whether new software or programme lists are available The only prerequisite is that your satellite receiving system is aligned with ASTRA 19 2 East In the Installation menu use the 4p 4w keys to select the Software Download sub menu and confirm this with Your receiver automatically searches for the ASTRA transponder which transmits the current software and programme list The following screen appears If there are no new versions an on screen message appears to inform you of this On Air Download Astra Horizontal 18V Display info Main SW Ch List info Text E Select M Main I Pressing in the Show Info item gives you information about the software and programme list being transmitted The Show Info Operating Software and Channel List items are automatically set to Yes if new information and content is available The left hand bar shows the relative signal level You can use the cursor keys TOUR i to deselect an item No Items that already inactive cannot be changed If you only want to update the software but leave your channel list alone deselect the Channel List field or vice versa You can also request Info Text only To update switch to Start and confirm with Q9 59 Installation Menu 60 The
47. ncept Language Selection Alphanumeric Assignment of Remote Control Number Keys Menu Structure Initial Setup Important Information Getting Started Receiver Factory Satellite Setting On Screen Display OSD General Help Function TV Radio Channel Message Error Message Video Text Programme Selection selecting a TV or Radio Programme Reception Status TV Radio Channel List Selecting TV Radio Programmes by Number Switching from a TV Programme to a Radio Programme Common Interface Important Information Inserting the Smartcard and the CA Module Information for Conax SECA Viaccess and CryptoWorks Users Timer Settings VPS Signal Audio Settings Setting the Volume Stereo and Two Channel Sound Playback AC 3 Turning Off the Sound Mute Programme Overview EPG EPG Electronic Programme Guide oo O O WO 0 0 0O N A OQ Contents EPG Timer Programming Managing Channel List Channels Selecting the Last Programmes Received Favourite Channel Setting Up a Favourite Channel Renaming the Favourite Lists Selecting a Favourite Channel from a Favourite List Undoing Favourite Selection Channel List Mode Favourite Satellite Alphabetical Complete Channel List Sorting Channels Deleting Channels Adding Channels Manually Adding Deleting Satellites Setting Up Satellites Deleting Satellites Password and Child Protection Password Factory Setting Setting the Password and Child Protection
48. ng antenna systems It is a single master multi slave system i e there is only ever one master in the satellite system All activities start from the master If DISEGC switching matrices are cascaded the master receiver must transmit the DISEqC signal several times so that all DiSEqC multi switches in the cascade receive their commands These days DIiSEqC components slaves must be reverse compatible i e respond to the analogue switching criteria from receivers that are only equipped with H V and 22 kHz control signals A DISEqC switching matrix will work with analogue switching critiera until the DiSEqC command from the master is received All analogue switching criteria are then ignored A sound transmission method that allows digital surround sound to be output on a home cinema system DVB is the abbreviation for Digital Video Broadcasting DVB S refers to the transmission method S satellite MPEG is the abbreviation for Moving Picture Experts Group a working group that formulates internationally applicable standards for the digital compression of video and audio MPEG 2 has established itself as the standard for compression of digital TV signals MPEG 2 works up to a data rate of 100 MBit s The Eb No ratio is a measure of the signal to noise ratio of a digital signal The value is not identical to the C N value familiar from analogue reception technology At Eb No values below 5 dB reception is normally
49. nische kundenberatung kathrein de service esc kathrein de The programme packages for the satellites and transponders are subject to constant changes In such cases it is necessary to reset the channels as the factory preset programming corresponds to the situation on the date of manufacture The information for this reset can be found on the Internet or in relevant magazines Our equipment is factory fitted with the most recent software version We are constantly working on adapting the software to the requirements of our customers and developments in technology The Software and Channel List Update section contains additional information Note that the Kathrein turntable has been designed exclusively for use with the Kathrein UFD 170 DVB receiver controller UFO micro and UFO mini are registered trademarks of KATHREIN Werke KG DiISEqC is a registered trademark of the European Telecommunications Satellite Organisation EUTELSAT Contents Foreword Contents Safety Instructions and Important Information Connection and Setup Connecting the Unit SAT IF Connection Reception Requirements Reception System Presets TV Connection Audio Connection Dolby Connection IR Receiver Inserting Batteries in the Remote Control Controls Displays and Connections Front View Rear View Remote Control Function Keys Important information on the remote control Remote control instruction sets Operating Instructions Menu Co
50. no longer possible FEC is the abbreviation for Forward Error Correction The FEC error rate corresponds to the Viterbi rate The PID Packet Identification number is an identification number for video signals and audio signals in the digital data stream of DVB MPEG 2 signals The receiver uses the PID number to create a unique assignment for the video and audio data transmission The PID PCR is the identification number for the synchronisation signal The PID PCR is normally identical to the video PID For programmes broadcast in multiple languages the audio PD can be entered manually to assign a different language to the TV programme After the PID is entered the digital receiver automatically selects the audio data identified by the PID number from the data stream and assigns it to the video signal Brief Technical Glossary Programme package Symbol rate Transponder Video bit rate Viterbi rate The programme package for a digital transponder normally includes several TV and radio programmes Each programme package has a fixed assignment for the transponder transmission frequency for polarisation horizontal or vertical for the symbol rate and for the Viterbi rate or error rate The symbol rate describes the quantity of data that is transmitted per second The symbol rate is measured in MSymbols s and is equal to the number of symbols received per second A transponder is a satellite transmitter which transmits TV and r
51. o enable you to locate errors You can find a detailed description of the individual menu functions in the relevant sections of this operating manual You can Call up help for each menu or menu function This help function provides you with a brief description of the most important functions of the selected menu option For example call up the main menu by pressing You can now view the help display for the Installation option by pressing Main Menu system Parameters Language Common interface HDP Antenna Setup AM 211248 JE Exit You can now view the help display for the Installation option by pressing Q9 You can use the D or keys to exit the help display and return to the main menu Pressing the D key again takes you back to the ori ginal programme you were receiving 19 On Screen Display OSD TV Radio Channel Message Channel message TV Channel message Radio Error Message 20 The channel message is displayed for a few seconds each time you change the programme or constantly if you press The indicates that a channel is being received even if no picture can be seen e g in radio mode f Astra 11 Bayeriscnes F 07 34 Bil Panoramabilder Bergw 07 30 0300 i Astra 1 Bayern 1 1409 U v Bayern 1 Caf 13 05 17 00 The TV symbol indicates a TV channel adjacent to it is the selected programme whether video text can be received and the
52. of the cable until it is securely fitted on the cable braid bent back 10 mm When fitting the connector make sure that no wires from the braiding are touching the inner conductor this could result in short circuit The quality of the reception signal depends on the connection Make sure that your own satellite antenna system is equipped with at least a universal LNB for digital reception in the high band range The presents for the control signals have been made for standard reception systems i e 14 18 V for polarity reversal and 22 kHz switching signal for low high band changeover on multi feed reception systems Connection and Setup TV Connection Audio Connection Dolby Connection IR Receiver Connect the UFD 170 TV Scart socket and the TV set with a Scart cable If your TV has a stereo feature you can receive the sound in stereo via the Scart connection If you want to play the sound on your hi fi system connect the audio cinch sockets to the input sockets on the hi fi system with an appropriate cable The Dolby Digital data flow output AC 3 is intended for connection to a Dolby Digital system Connect the infrared receiver to the IR REMOTE IN socket and position it such that it has a visual connection to the remote control The UFD 170 can only be operated by remote control Inserting Batteries in the Remote Control E Remove the cover on the rear of the remote control Insert the two ba
53. ondition of the superstructure and external fittings Failure to lower the antenna can result in severe damage to the antenna and to the vehicle Repairs Ensure that any repairs to your unit are only carried out by qualified personnel Opening the unit and attempting to repair it yourself results in forfeiture of all warranty claims Improper work on the unit can endanger the electrical safety of the unit The manufacturer shall accept no liability for accidents caused by the user opening the unit Connections Incorrect wiring of the connections can lead to operating faults or defects on the unit Long periods of absence storms Always turn off the unit at the power switch if you will be absent for a long time or there is a storm This also applies to the other equipment connected to the unit Wiring harness isolation is also recommended Note any timer programmes receiver and turn the unit on again promptly before the recording time Installation location Every piece of electronic equipment generates heat However the heating of this unit lies within the permissible range Sensitive furniture surfaces and veneers may become discoloured by the effects of heat over time The feet of the unit can also cause colour changes to treated furniture surfaces If necessary place the unit on a suitable stable and flat base Ventilation The heat occuring in this unit is adequately dissipated Never install the unit in a cupboard or on shelves w
54. our You can now use the number keys to enter a new frequency appropriate for your system This also applies to the L O Low setting This is reached using the lt lt keys You can exit the menu by pressing four times this also confirms the saving of the set value If you make an incorrect setting you will see the following message Poor or no signal The factory setting is On Select using the t keys Under normal circumstances the supply voltage should be turned on For community antenna systems you must ascertain whether the supply voltage needs to be turned off The factory setting is Off Select using the A keys Under this option you can turn the supply voltage for the LNB on or off in receiver standby mode For single and community antenna systems it can be turned off If your receiver is connected to a multi feed antenna which is aligned with the HOTBIRD satellites for example you must change the receiver settings for the DiSEqC Digital Satellite Equipment Control signal This also applies to other satellites Different control signals are required to select the satellite signals 91 Installation Menu Note DiSEqC 1 Setting This setting is not necessary for caravan operation DiSEqC 2 Setting This setting is not necessary for caravan operation 32 To date the LNB supply voltage of 14 18 V and the 22 kHz signal superimposed on the LNB supply voltage ha
55. own in the right hand corner After completion of the search the video text broadcast by the relevant programme provider appears P100 100 SAARTE XT Mi 13710 ee eo imm SFE 2 I u n ee u S Ri HLUTUR Nachrichten 110 rd i Wee Wetter 160 Index Sport 200 Redaktion Fernscnen 300 SR Lnvorn H rfunk 400 Reisen Jetzt im SR SUDWEST Fernschen RAL E uns NZ The individual pages can then be opened using the number keys During the search a white star flashes in the top left hand corner of the screen Press to exit the video text 21 Programme Selection This section explains how to select television and radio programmes on your UFD 170 The description of the functions assumes that the UFD 170 has been connected and turned on properly Selecting a TV or Radio Programme Note Reception Status 22 Programme selection works in exactly the same way in TV and radio mode We will therefore only explain how to select TV programmes here The procedure for selecting a radio programme is identical to that described for the TV programmes To select additional programmes in ascending or descending order in the programme memory simply press the 2 keys after turning on the UFD 170 After each change of programme an on screen display shows you the selected programme the time the programme start and end times and the programme title in an information bar if this data is broadcast by the programme provider i
56. provide information about the strength relative level of the signal and its quality However this information cannot be used to draw any conclusions about the quality of the antenna system For operation with a rotor DISEqC 1 2 select Motor Goto 0 On in the third line In the next line Move Save you can align the antenna to the East or the West The optimum setup can be viewed in the Level bar chart In the Set Limit Value line you can set the outermost aiming point limited by a wall or another obstruction in a Westerly or Easterly direction Always read the operating manual supplied by the rotor manufacturer this applies in particular to settings different from those described above 53 Installation Menu Satellite Search Note 54 In the Satellite Search menu you can set the receiver to search for channels on a satellite of your choice or on all satellites that can be search is started with received it You can choose between the following settings Search mode Free encrypted Free only PREMIERE Canal Satelite CANALSATELLIT CANAL Stream TELE In this menu you can use the 4p 4 keys t ll up the individual menu options and make the settings with the keys The Satellite name All satellites or individual satellites e g ASTRA HOTBIRD Selecting Free and encrypted under the Search Mode menu option and All satellites under the Sa
57. r to the Alphanumeric Assignment of Remote Control Number Keys section The factory setting is UFD 170 This completes all the settings to secure and identify your satellite receiver If you have forgotten your password you must contact your dealer who will be able to unlock your receiver for you Child Protection Locking a Channel Similar to marking your preferred channels with the apple symbol you can set up child protection to prevent unauthorised access by children The channels are marked with the padlock symbol in the TV or Radio channel list The key takes you to the channel list Here you can use the X P and t keyss to select the channel you want to lock Confirm your selection with and the padlock icon appears in the list after the selected channel see example below to unlock press again You are automatically taken to the display for the following channel in the channel list Press to exit the channel list and save your settings RY Channel List All List KABEL1 9 11 836 GHz Horizoht t 18V DSF Bayerisches F 27300 MEPS a Hr fernsehen t ARDI 1 7 14 S DWEST BW FAV DEL 15 WDR K ln LOCK M ADD 16 BR alpha MOVE R MODE i PDage Up On O Watch SmE 0 9 Nore 45 Password and Child Protection When a locked channel is selected the following message appears This channel can only be viewed after entering the passwo
58. rd using the number keys 46 Setting System Parameters Child Protection System Information You should not change the following settings without a good reason as they are factory settings or operating settings that are tailored to your receiving system New settings are only required if the receiving system is changed The selected menus sub menus and positions as well as the parameters to be set are each highlighted in colour The menus are self explanatory to a great extent Help for the selected item is available by pressing Press again to exit the Help menu The System Parameters menu is reached from the main menu open with the key Use the lt gt keys to go to the System Parameters option and confirm your selection with The following screen appears System Parameters Parental Control System Information Local time Timer DL Saving No TV Type MULTI Aspect Ratio Screen M T Prey The items are highlighted using the ww amp P keys selected u with the key and set or changed with the number keys keys or the This topic is dealt with in detail in the Password and Child Protection section Under the System Information option you will find factory settings that cannot be changed and are only intended for service purposes Press the D key to return to the System Parameters sub menu 47 Setting System Parameters Local Time Timer
59. s Du NEN ES d adul m No Connection between Type of connection SAT IF connection coaxial cable with standard F connector Using connecting cable supplied Using supplied control data cable Power supply with power supply cable supplied Connection with cinch cinch cable supplied 6 UFD 170 and hi fi system Connection can be via cinch cable not included Connection can be via cinch cable not included SAT ZF output Control unit and SAT IF Supplied with connection already set up required for input Receiver communication between receiver and control unit in UFD 170 o Receiver and infrared receiver Connection via cable for infrared receiver supplied Antenna and receiver SAT IF input SAT IF connection option if UFD 170 is intended for stationary use e g in an apartment 61 Connection Diagram SAT ZF Connection The coaxial cable coming from the antenna is connected to the SAT IF input on the UFD 170 The SAT IF output on the UFD 170 control unit is already connected to the SAT IF input on the UFD 170 receiver with the coaxial cable supplied The correct sequence must be observed due to the power supply for the LNB via coaxial cable and communication between the two boards in the UFD 170 control unit and receiver On Board Network Connection N d b Control Cable 62 In terms of the on board network connection refer to the information in the installation manua
60. shown Delete deletes the channel shown Add adds a new channel Move moves the channel to a different position Mode selects the mode for the channel list The lt gt p keys skip to the next programme whereas the keys skip to the next page A selection is confirmed with You can also select a programme by entering a number Pressing m you exit the channel list and return you to the previously selected programme 23 Programme Selection Selecting TV Radio Programmes by Number Example You can select a different programme while a programme is being shown To enter the programme number use the number keys to You want to select the programme DSF at programme number 15 programme number assignment is an example To do this enter the numbers and The receiver waiting time for entry of the next digit is around three seconds The procedure for all other programmes including those with three digit programme numbers is exactly the same Switching from a TV Programme to a Radio Programme 24 You can switch from TV mode to radio mode To do this press on your remote control The receiver then switches to the last radio pro gramme selected You can use the or key to return to TV mode When switching to radio mode just as in TV mode you will see a display for the programme received 1 Astra e Bayern 4 Klas 13 13 11 Ree 12 05 14 00 In radio mode the s
61. sturdy and non slip shoes The person carrying out the repairs has a secure position to stand and hold on while working The roof and climbing equipment used e g ladder are dry clean and non slip The roof can withstand the weight of the person carrying out the repairs Attention Risk of death or injury due to falling or roof collapse You may not hold onto the antenna as the rocker suddenly comes free during dismantling Attention Risk of death and injury due to falling or crushing Nobody should be below the antenna inside the caravan motorhome during dismantling uninstallation Attention Risk of death or injury due to possible roof collapse and falling parts Manual Lowering to Park Position Manual Retraction 1 A plastic cover is located in the centre of the axis see arrow Lever this off with a narrow slotted screwdriver 2 Behind the cover is an M8 hexagon head screw Unscrew it using a socket wrench size 13 mm After removing the M8 screw a further thread can be seen 3 Attention Secure and support the antenna to prevent it tipping over The connection to the rocker can suddenly come loose during the next step point 4 It is then no longer connected to the turntable 4 Screw an M12 screw into this thread minimum length 22 mm You will need a socket wrench for this size 19 mm Screwing in the M12 screw removes the rocker from the tapered shaft and releases the catch 5 ilt th
62. sub menus and options as well as the parameters to be set are all highlighted in colour The menus are self explanatory to a great extent For a rough overview of the structure of the main menu and the subsequent sub menus you can refer to the Menu Structure section of this manual MEETS LU Language Common Interface HDP Anterma Setup M Next M W Exit The main menu is opened by pressing and the sub menus are selected using the 4 amp W keys The sub menus are accessed by pressing The options in the sub menus are selected using the qa 4g keys The settings in those options are made using either the A keys or the number keys The main menu sub menus and the individual options are exitted using or The language for the on screen display is set I Sp Select menu language i e g English The languages available are German English Italian French Dutch Portuguese Spanish and Turkish Operating Instructions Alphanumeric Assignment of Remote Control Number Keys You use the number keys to enter programme and satellite names The numbers and letters appear in the name fields of the corresponding menus Place the cursor in the name field The first character is automatically given a dark background You can now use the the number keys to enter letters by pressing the relevant key several times For example the 2 key is also used for A B and C see table below 14
63. tellite Name menu option gives you the widest variety of channels Satellite Scan Prvate Gold SHo 1 na Extreme Sport SRo 2 Deva SRo2 5Ro1 Test NLR During scanning the signal quality the scanning progress and the new channels found are displayed At the end you will see a message to tell you that the search is complete To confirm press All new chan nels are added to the existing channel list and highlighted in a different colour Pressing the D key pauses the search pressing the D key twice aborts the search Installation Menu Changing Searching for Deleting Transponders In this menu the transponders can scan selectively for channels for example if new channels are offered in a particular broadcaster s range This information is available on the Internet or in specialist magazines You reach this menu from the installation menu using the P gv IE JO want tO Range your l keys and confirm your selection with the key system over to a new satellite you must manually enter at least one recognised transponder The transponder number TP Edit Scan specified in brackets is an internal reference number for the receiver and has nothing to do with the transponder number of the satellite TP Frequency Polarization Symbol Rate Scan TP Delete You can now access the individual items using the qw keys The following settings are possible Preferred satellite using or Transpon
64. th The se lected favourite list appears with all the channels you have sa ved to it Select the channel to be deleted with the cursor keys and press The receiver now skips to an overview of all favourite lists Select the favourite list from which you want to de lete the channel and press Q9 he receiver has now dele ted the channel from the selected favourite list Pressing takes you back to the TV screen You will see a short message to confirm that the data has been saved 3 Managing Channel List Channels Channel List Mode Favourite Satellite Alphabetical 38 To select the channel list mode press for the channel list followed by for the mode The following screen appears RV Channel List Free Scrambled Bay Satellite Astra SR WDR K ln 7 gum ADD BR alpha G MOVE R MODE OW Select M W Exit The channel list mode allows you to determine what you want to see in the channel list You can choose between Free only or Free encrypted Favourites lists 1 5 Satellite ASTRA HotBird etc Alphabetical The selection Free only Free encrypted applies to all subsequent settings in channel list mode All other settings favourites satellite alphabetical only affect the relevant selection Under Favourites you 4 between the five favourite lists which you select using the keys and the key You will then see a channel list showing the chann
65. tteries supplied into the remote control ensuring correct polarity this is shown on the base of the battery compartment olide the cover back onto the housing until it clicks into place Used batteries are special waste Do not throw used batteries into your household waste take them to a collection point for old batteries Electronic equipment is not household waste in accordance with directive 2002 96 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of 27 January 2003 on used electrical and electronic equipment it must be disposed of properly At the end of its service life take this unit for disposal at a relevant official collection point Controls Displays and Connections This section contains a brief description of all controls displays and connections Front View ae me Rear View POWER IN 10 9 13 8V 710A AUDIO VIDEO DIGITAL AUDIO Dit pousy DIGITAL DATA 1 0 BITSTREAM our 2 Receiver SAT IF signal input connected to 5 RS 232 data interface Turntable unit SAT IF signal loop output connected to 3 iB Vieocuut compestecobu 1 Doby Digital data stream ouput ac Ol OO NO 10 Controls Displays and Connections Remote Control Function Keys The key symbols presented here can also be found in the description of the operating steps Switching to remote control Select last four programmes Select
66. tting you will see the message Poor or no signal With cascading switches a total of 16 satellite positions can be saved under the DiSeqC 2 menu option Horizontal Vertical and High Low give a total of 256 possible settings These settings should only be made and this kind of system only set up by aqualified engineer Installation Menu Antenna Setup This setting is not necessary for caravan operation Operation with antenna rotor positioner DISEqC 1 2 This setting is not necessary for caravan operation This menu is exclusively intended for service purposes and be used to align the antenna in an emergency if no measuring instruments are available The key activates a search tone the pitch of which cor responds to the signal strength the higher the sound the better the signal Antenna Setup Horizontaht8V 27 500 MSPS Motor Goto 0 OFF Move Save Stop Set Limit Disable My longitude 000 0 My latitude 00 0 THLEELEELLELLEL TEE mS i a DM Main P Prev Beep Sound Oe 5 5 S In this menu you can use the ep qs keys to call up the i keys The first line is used to specify the satellite and the second line to specify the transponder individual menu options and make the settings with the In the small box immediately to the right the first line shows the polarisation of the received signal and the second line shows the transmitted symbol rate The bars
67. ure After doing this do not initially turn off the receiver with the power switch but use the remote control for this pur pose as otherwise the settings will be lost Here you can use the t keys to specify whether your TV set is a PAL Multi standard or NTSC set Pressing twice takes you back to the normal TV picture Here you can use the A keys to select the type of picture format for which your TV set is designed This will either be 4 3 format 16 9 format or Auto Pressing twice takes you back to the normal TV picture Setting System Parameters Screen A V Mode Here you can use the A keys to select the type of screen display P S Pan Scan Full screen for 4 3 sets caution margins are cropped Letterbox display This setting enforces the widescreen format for a 4 3 set Pressing D twice takes you back to the normal TV picture Here you can use the 9 keys to select the type of video signal at the scart socket Select the signal that your TV set can process Follow the instructions in the operating manual for your TV set FBAS composite colour signal Combined basic band signal Co lour Picture Blank synchronisation signal or RGB Red Green Blue signal or Y C SVH S signal luminance chrominance Pressing D twice takes you back to the normal TV picture 49 Installation Menu You should not change the following settings without a good reason
68. ve been sufficient for signal selection for most applications These four switching signals allow you to switch between the horizontally and vertically polarised signals and between two satellites multi feed reception To extend the frequency range to the 12 GHz range high band or for reception from more than two satellites additional control signals are required for LNB actuation and signal selection The DiSEqC signal is responsible for this This is a special modulation of the existing 22 kHz signal Before every change you should note the settings on the form at the end of the operating manual The satellites listed under the Receiver Factory Satellite Settings option are preset in the factory The requirement is that you have not made any changes in the DiSEqC UFO Setup menu see also DiSEqC UFO Setup The DiSEqC signal is used to switch between the target satellites Use the ED keys to select the satellites for which you want to change the DiSEqC setting and confirm your selection with If you want to add a new satellite the procedure is as described under Setting Up Satellites select the DiSEqC 1 menu option Use the amp lt q keys You can then use the setting 1 2 3 or 4 keys to select the desired DiSEqC Press D four times to exit the menu and return to the TV screen This also confirms the saving of the set value If you make an incorrect se
69. will see a message confirming that your changes have been saved and the information display for the currently selected channel will appear on the screen for a few seconds The new channel is added to the existing channel list The required PIDs are available in the relevant magazines and on the Internet For details of how to make alphanumeric entries refer to the Alphanumeric Assignment of Remote Control Number Keys section 41 Adding Deleting Satellites Setting Up Satellites Note 42 If the UFD 170 is being operated in conjunction with the Kathrein turntable nothing may be changed in this list Changes to this list would result in the assignment being lost and the turntable would not longer be able to find the satellites You can add new satellites in the LNB Configuration menu To do this you must know the orbit position you need to aim at The system must be set up accordingly To align the antenna you can use the Antenna Setup menu option Press to open the main menu Use the cursor keys to se lect the Installation sub menu and press Q9 Now select the LNB Configuration option using the cursor and the keys In the next steps use the 4p qw keys to go to the next free position e g the entry USER9Q LNB Configuration telstari2 HISPASAT Position EUTEL7 High L O amos Low L O THOR Power SIRIUS Stand By ARABSAT i DiSEqC 1 USER9 y DiSEqC 2 1 0 Pag
70. wo figures indicates how many sound channels are being transmitted and the second figure indicates which channel is currently selected Use the key to open the Audio menu for sound and language se lection where you can make the desired settings as long as they are included in the received signal e g language selection soundtrack Dolby Digital Subtitle Audio Audio Track 1 of 3 German Audio Mode Stereo Dig Output MPEG Stereo s using the 4 Ww keys and make the desi Select the menu M red settings with the keys Press again to exit the men subtitles are broadcast you can select their language using the keys in the Subtitle track bar Confirm your entry with 30 Audio Settings AC 3 Note The following audio settings are possible Soundtrack 1 of 2 2012 3 of 3 Audio mode Stereo Mono left Mono right Digital output MPEG stereo Dolby Digital AC 3 The receiver has an audio output for AC 3 format Dolby Digital This gives you the opportunity to bring cinema quality sound into your living room Only connect the digital audio output to an appropriate Dolby Digital system Always follow the safety instructions and the operating instructions for your Dolby Digital system Only a few programme providers broadcast the AC 3 format If no AC3 signal is received you can only make the normal stereo or mono settings and choose the broadcast languages Turning Off the Sound

Download Pdf Manuals

Related Search

Related Contents

  K。KUY。  Samsung DVD-P350K Kasutusjuhend  イナバ物置 組立説明書 【N40】  CP500 User Manual Italain  Jwin JX-CD4000 User's Manual  F I R S T C L A S S · B R A N D Dispensette® TA · Trace Analysis La  【 シャープ「アクオス」の再スキャン方法 】※一例  Istruzioni per l'uso  確定申告書・贈与税申告書・電子申告 ネット更新  

Copyright © All rights reserved. Failed to retrieve file