Karcher K 2.45 User's Manual
Contents
1. WARNING When using this product basic precautions should always be followed including the following Read all the instructions before using the product To reduce the risk of injury close supervision is necessary when a product is used near children e Know how to stop the pressure washer and bleed pressures quickly Be thoroughly familiar with the controls Stay alert watch what you are doing e Do not operate the product when fatigued or under the influence of alcohol or drugs e Keep operating area clear of all persons e Do not overreach or stand on unstable support Keep good footing and balance at all times e Follow the maintenance instructions speci fied in the manual e This Pressure Washer Is Provided With A Ground Fault Circuit Interrupter Built Into The Power Cord Plug If Replacement Of The Plug Or Cord Is Needed Use Only Identical Replacement Parts WARNING Risk of Injection or Injury Do Not Direct Discharge Stream At Persons e High pressure jets can be dangerous if subject to misuse The jet must not be directed at persons animals electrical devices or the machine itself Wear safety goggles e Do not use acids solvents or any other flammable material in this product These products can cause physical injuries to the operator and irreversible damage to the machine This machine has been designed for use with cleaning detergent supplied or recom mended by the manufacturer2. Purpose Cleaner place detergent suction tube directly into cleaning solution and apply to surface at low pressure For best results limit your work area to smaller sections of approximately 25 square feet Allow Karcher All Purpose Cleaner to remain on surface 1 3 minutes Do not allow detergent to dry on surface Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 3 6 inches from the cleaning surface Always clean from top to bottom and from left to right For removing extremely stubborn stains use Karcher Rotating Nozzle Spray Wand Cars Boats amp Motorcycles with or without detergent Pre rinse vehicle with fresh water If using Karcher Vehicle Wash place detergent suction tube directly into cleaning solution and apply to surface at low pressure For best results clean one side of vehicle at a time and always apply detergent from bottom to top do not allow detergent to dry on surface If needed use special Wash Brush Attachment to remove stubborn dirt Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 6 8 inches from the cleaning surface distance should increase when rinsing pin striping or other sensitive surfaces Always clean from top to bottom and from left to right For best results wipe surface dry with a chamois or soft dry cloth Caution Do not use rotating nozzle spray wand on vehicles as it may cause damage CLEANING TIPS continued Bar
3. ACCESSORIES Vario spray wand The Vario spray wand allows you to adjust the cleaning pressure To clean at maximum pressure the Vario wand must be positioned to the high pressure setting To apply detergent the wand must be positioned to the low pressure setting Dirtblaster spray wand This wand features a 0 pencil jet which rotates 360 for maximum dirt cutting action effectively increasing cleaning performance up to 50 This wand combines the cleaning performance of a 0 pencil jet with the surface coverage of a wide angle nozzle Not recommended for soft materials siding painted surfaces decks or autos For higher pressure turn wand collar in the plus direction For lower pressure turn wand a collar in the minus direction AN Warning TO AVOID SERIOUS INJURY NEVER POINT SPRAY NOZZLE AT YOURSELF OTHER PERSONS OR ANIMALS WORKING WITH DETERGENTS Detergents can only be applied at low pressure eo i a For best results see Cleaning Tips on pages 8 amp 9 for specific information on how to clean different surfaces Step 1 To apply detergents install the Always Use Karcher Vario spray wand Set the Vario spray wand Detergents for Best Results to the low pressure setting by turning the Karcher biodegradable detergents wand collar The wand must be set in the low are specially formulated to protect the pressure position to appl
4. KARCHER Model K 2 45 High Pressure Washer Operator Manual OVGINIOW arei r T 2 ProcaullOnS sorcininsrepet isrann aiar Erna SA chastuaelagk cae svceeuestades 2 4 Assembly Instructions cissie nareread 4 Operating Instructions sssssisesresisssireranrsnsdsineennesnisnonseni 5 GPCI INSTUCU ONS occ cccecasccccetcevdasec ctor uaee nseeed ates yenseiedes 6 Using the Accessories 00 eeeeeeeeeeeeeeeeeeneeeeeeteeenneeeeeens 6 Working with Detergent cccccccecceeceeeeeeeeeeeeeeeeeeeeeees 7 Shut Down and Clean Up cceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 8 TAKING a Brakes niania 8 Winterizing and Long Term Storage sesser 8 CIGANING TIPS rsrsrsrs 9 10 Optional Cleaning Accessories sesssssssserssrresssrrerreene 10 TOUDIGSMOOUNG rcroisrabnarnnnn 11 12 Specifications Operating pressure 1400 PSI Water volume 1 3 GPM Voltage 120 V Amp draw 14 AMPS In USA Call 1 800 537 4129 or visit our website www karcher usa com 5 961 145 2006873 04 04 Model K 2 45 OVERVIEW Item Description Item Description 1 On Off switch 8 Vario spray wand 2 Connector for detergent suction tube 9 Trigger gun 3 High pressure outlet 10 Trigger gun safety lock 4 Water inlet with internal water filter 11 High pressure hose 5 Detergent filter 12 Power cord 6 Detergent suction tube 13 Ground fault Circuit Interrupter GFCI 7 Dirtblaster wand IMPORTANT PRECAUTIONS Read First IMPORTANT SAFETY INSTRUCTIONS
5. The use of other cleaning detergents may affect the operation of the machine and void the warranty The Gun Safety Lock prevents the trigger from accidentally being engaged This safety feature does not lock trigger in the on position SAVE THESE INSTRUCTIONS GROUND FAULT CIRCUIT INTERRUPTER PROTECTION This pressure washer is provided with a ground fault circuit interrupter GFCI built into the plug of the power supply cord This device provides additional protection from the risk of electric shock Should replacement of the plug or cord become necessary use only identical replacement parts that include GFCI protection SERVICING OFA DOUBLE INSULATED APPLIANCE In a double insulated product two systems of insulation are provided instead of grounding No grounding means is provided on a double insulated product nor should a means for grounding be added to the product Servicing a double insulated product requires extreme care and knowledge of the system and should be done only by qualified service personnel Replacement parts for a double insulated product must be identical to the parts they replace A double insulated product is marked with the words DOUBLE INSULATION or DOUBLE INSULATED The symbol 0 may also be marked on the product EXTENSION CORDS Use a sufficient gauge Up to 25 ft 12 2 AWG 25 to 50 ft 10 2 AWG Use only extension cords that are intended for outdoor use These
6. becue Grills Outdoor Power Equipment amp Gardening Tools with or without detergent Pre rinse cleaning surface with fresh water If using Karcher All Purpose Cleaner or Degreaser place detergent suction tube directly into cleaning solution and apply detergent at low pressure Allow Karcher detergent to remain on surface 1 3 minutes Do not allow detergent to dry on surface Rinse at high pressure keeping the spray nozzle approximately 3 6 inches from the cleaning surface For removing extremely stubborn dirt it may be necessary to move the spray nozzle even closer to the surface for greater dirt cutting action To remove caked on mud from garbage cans lawn mower blades wheel barrels or other non sensitive metal surfaces you may want to use the Karcher Rotating Nozzle Spray Wand Caution Do not use rotating nozzle spray wand on cloth plastic or other sensitive surfaces as it may cause damage Patio amp Lawn Furniture with or without detergent Pre rinse furniture and surrounding area with fresh water If using Karcher All Purpose Cleaner place detergent suction tube directly into cleaning solution and apply to surface at low pressure Allow Karcher All Purpose Cleaner to remain on surface 1 3 minutes Do not allow detergent to dry on surface If needed use special Wash Brush Attachment to remove stubborn dirt Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 3 6 inches from the cleani
7. extension cords are identified by a marking Acceptable for use with outdoor appliances store indoors while not in use Use only extension cords having an electrical rating not less than the rating of the product Do not use damaged extension cords Examine extension cord before using and replace if damaged Do not abuse extension cord and do not yank on any cord to disconnect Keep cord away from heat and sharp edges Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord If you are using an extension cord it should always be completely unwound from the cable drum WARNING To reduce the risk of electrocution keep all connections dry and off the ground Do not touch plug with wet hands IMPORTANT PRECAUTIONS continued Water Supply Cold Water Only e Water hose must be at least 3 4 inch in e The water supply temperature must not diameter exceed 104 F 40 C e Flow rate of water supply must not fall e Never use the pressure washer to draw in below 2 5 GPM gallons per minute water contaminated with solvents e g e Flow rate can be determined by running the paint thinners gasoline oil etc water for one minute into an empty 5 gallon e Always prevent debris from being drawn container into the unit by using a clean water source ASSEMBLY INSTRUCTIONS g5 s Step 1 Step 2 Step 3 Pull out the locking slide from Insert the smal
8. her Deck Wash to remain on surface 1 3 minutes Do not allow detergent to dry on surface Rinse at high pressure in a long sweeping motion keeping the spray nozzle approximately 3 6 inches from the cleaning surface Always clean from top to bottom and from left to right When moving on to a new section of the cleaning surface be sure to overlap the previous section to eliminate stop marks and ensure a more even cleaning result Caution Do not use rotating nozzle spray wand on wood surface as it may cause damage House Siding with or without detergent Pre rinse cleaning surface with fresh water If using Karcher House Wash place detergent suction tube directly into cleaning solution and apply to surface at low pressure for best results limit your work area to sections of approximately 6 feet and always apply detergent from bottom to top Allow Karcher House Wash to remain on surface 1 3 minutes Do not allow detergent to dry on surface if surface appears to be drying simply wet down surface with fresh water If needed use special Wash Brush Attachment to remove stubborn dirt Rinse at high pressure from top to bottom in an even sweeping motion keeping the spray nozzle approximately 6 inches from the cleaning surface Caution Do not use rotating nozzle spray wand on siding as it may cause damage Cement Patios Brick and Stone with or without detergent Pre rinse cleaning surface with fresh water If using Karcher All
9. l end of the Push the locking slide back into the right side of the trigger high pressure hose into place the trigger gun to lock the hose gun handle in position Step 4 Connect the detergent suction tube to the pressure washer OPERATING INSTRUCTIONS Step 1 Step 2 Insert the spray wand of your Connect the high pressure hose to the unit s high choice into the trigger gun Push in and pressure outlet turn clockwise to lock spray wand in place Step 3 Step 4 Connect garden hose to unit s water inlet Connect garden hose to the cold water source and turn water on completely S Step 5 Step 6 Plug the power cord into the power outlet Unlock Turn on the pressure washer l on the lock of the trigger gun Press TEST then The motor starts only if the trigger of press RESET to assure proper connection to the gun is pulled and shuts off when power Trigger the gun to eliminate trapped air the trigger is released wait for a steady flow of water to emerge from the CAUTION Never operate pressure spray nozzle washer without the water turned on Step 1 Plug the Ground Fault Circuit Interrupter GFCI into a working outlet Note The actual appearance of the GFCI may be different from this illustration Step 2 Press TEST then press RESET to assure proper connection to power USING THE
10. le Oil Drip In USA Call 1 800 537 4129 or visit our website www karcher usa com Detergent suction tube not properly connected to the machine Solution Check connection Detergent is too thick Dilute detergent for best results use Karcher detergent Filter on detergent suction tube is clogged Run warm water through filter to remove debris Damaged or clogged detergent suction tube Remove obstruction or replace detergent suction tube Spray wand is in high pressure position Turn spray wand tip to low pressure position Discharge nozzle is obstructed Loose fittings Blow out or remove debris with ine needle Tighten fittings Missing worn rubber washer Spray wand not properly attached nsert new washer nsert the spray wand into the gun Carefully press in against the spring tension and twist into the ocked position Broken o ring or plastic insert Pump is sucking air Loose fittings Call Karcher customer service hotline and order repair kit part no 2 883 111 0 Check that hoses and fittings are air tight Turn off machine and purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle Check that all fittings are tight Water seals are damaged or worn Oil seals are damaged or worn Call service center Call service center If you encounter any additional difficulties no
11. ng surface For best results clean from top to bottom and from left to right Caution Do not use rotating nozzle spray wand on patio or lawn furniture as it may cause damage Recommendations e Before cleaning any surface an inconspicuous area should be cleaned to test spray pattern and distance for maximum cleaning results e If painted surfaces are pealing or chipping use extreme caution as pressure washer may remove the loose paint from the surface OPTIONAL CLEANING Optional cleaning accessories are available to further enhance your cleaning capabilities See accessories order form for product descriptions and ordering instructions e Rotating Wash Brush e Wash Brush e House Washing Wand e Extension Wand e Rotating Spray Wand e Flexible Spray Wand e Underbody Spray Wand e Telescopic Spray Wand e Pipe Drain Cleaner e Floor Washing Tool e Sandblasting Attachment e Detergent Foamer Attachment e Water Pumping Kit e Water Suction Hose e Extension Hose 25 TROUBLESHOOTING Disconnect the machine from the power source before making any repair Symptom Motor will not start Unit does not reach high pressure Output pressure varies high and low On Off switch is in the OFF position Solution Turn switch to the ON position Power cord is not plugged in Plug in power cord Extension cord is too long Extension cord is not proper gauge Extension cord is damaged Re
12. place extension cord with either a 25 ft 12 2 gauge cord or a 50 ft 10 2 gauge cord Electrical outlet does not supply adequate power Try a different outlet Tripped circuit breaker Diameter of garden hose is too small Reset breaker power supply or ground fault circuit interrupter Replace with a 3 4 inch garden hose Water supply is restricted Check garden hose for kinks leaks and blockage Not enough inlet water supply Open water source full force Water inlet filter is clogged Remove filter and rinse out in warm water Spray wand is in low pressure position Not enough inlet water supply Turn spray wand to high pressure position Turn water on full force Check garden hose for kinks leaks or blockage Pump is sucking air Check that hoses and fittings are air tight Turn off machine and purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle Water inlet filter is clogged Remove filter and rinse out in warm water Discharge nozzle is obstructed Blow out or remove debris with a fine needle Calcified gun hose or spray wand Run distilled vinegar through detergent suction tube TROUBLESHOOTING continued Symptom No detergent Garden hose connection leaks Spray wand or Spray wand extension leaks Pump is noisy Water leaks from pump up to 10 drops per minute is permissib
13. t listed please call our service center for help Karcher Customer Support USA
14. w pressure for one minute Step 6 Disconnect the garden hose Disconnect the high pressure hose from the high pressure from the water inlet on the unit outlet and engage the gun safety lock TAKING A BREAK five minutes or more Step 1 i Step 2 Engage gun Turn pressure safety lock i washer to 0 position MAINTENANCE INSTRUCTIONS Cleaning the 1 water inlet filter p Pull out the water inlet he filter with flat nose E pliers and rinse filter in warm water Cleaning the detergent filter Pull out the detergent suction tube and rinse filter in warm water WINTERIZING AND LONG TERM STORAGE 1 Disconnect all water connections 2 Turn on the machine for a few seconds until the water which had remained in the pump exits Turn off immediately 3 Do not allow high pressure hose to become kinked 4 Store the machine and accessories in a room which does not reach freezing temperatures Caution Failure to follow the above directions will result in damage to the pump assembly and accessories Deck Cleaning with or without detergent Pre rinse deck and surrounding area with fresh water If using Karcher Deck Wash place detergent suction tube directly into cleaning solution and apply to surface at low pressure For best results limit your work area to smaller sections of approximately 25 square feet Allow Karc
15. y detergents environment and your pressure washer Special formula won t clog the suction tube filter and will protect the internal parts of the pressure washer for a longer life For Karcher ca Detergents check your retailer or call In USA Call 1 800 537 4129 or visit our website g www karcher usa com The following Karcher detergents are available e Vehicle Wash e House Wash Step 2 Fill a container with Karcher Degreaser e Deck Wash detergent Place the filter end of detergent e All Purpose Cleaner suction tube into the container Caution Never use e Bleach Chlorine products and other corrosive chemicals e Liquids containing solvents i e paint thinners gasoline oils a e Tri sodium phosphate products Step 3 Turn on the pressure washer e Ammonia products Pull trigger to operate unit Liquid detergent P is drawn into the unit and mixed with water e Sclc Dased products Apply detergent to work area Do not allow These chemicals will harm the unit and detergent to dry on surface will damage the surface being cleaned SHUTTING DOWN amp CLEAN UP 0 Step 1 Step 2 Step 3 Step 4 Remove detergent suction Turn the switch to 0 Turn off the water Press trigger to tube from container and position and unplug source release water insert into 1 gallon of fresh cord from outlet pressure water Siphon water at lo
Download Pdf Manuals
Related Search