JVC TM-H150CG User's Manual
Contents
1. T OL Acceptable signal formats when installed on this monitor Connection terminal 525 60i 625 50i Attach to the connection terminal of the input card slot on the EMBEDDED AUDIO 8ch monitor Audio signal output terminal Outputs the analog audio signal after decoding the EMBEDDED AUDIO signal The input signal from the input terminal currently selected IN1 or IN2 is output from this terminal his terminal outputs the same audio signal as the audio sound output from the speaker NOTES No signal is output from the audio signal output terminal when the monitor is in stand by mode Even when the input signal is switched from the SDI Input Card this terminal still outputs the audio signal from the IN1 or IN2 which is selected last time IMPORTANT Do not use any other input card than the input cards listed on pages 7 and 8 Using other input cards may cause malfunction or damage the monitor Such malfunction or damage caused by using other input cards cannot be warranted e If any equipment is not connected to a bridged output OUT terminal be sure not to connect any cords to the bridged output OUT terminal Connecting a cord to a bridged output OUT terminal will cause the terminating resistance switch to open auto terminate function e When making a bridge connection connect the input IN and output OUT terminals on the monitor to separate video components For2. Pressing the button again returns the aspect ratio to 4 3 19 INPUT SELECT buttons Select an input to display A Select the video signal input to the VIDEO A terminal and the audio signal input to the AUDIO A terminal B Select the video signal input to the VIDEO B terminal and the audio signal input to the AUDIO B terminal When both an Y C S video signal and a composite signal are input to the VIDEO B terminal the Y C signal has priority over the composite signal C D SLOT Select the signal input to the input card installed in the input card slot on the rear panel For details about how to select the input signal through the input card see pages 7 and 8 The corresponding button of the input currently selected lights up Power lamp Unlit The main power is off Orange The main power is on and the monitor is in stand by mode Green The monitor is on I o Z TT Stand by button Turns on and off the monitor when the main power is on NOTE You can set the delay time between when the stand by button is pressed and when the monitor actually turns on See RUSH DELAY on page 12 Speaker A built in speaker is on the side panel I Controls and Features cont d Rear Panel VIDEO A terminal Input IN and output OUT terminals for composite signals The IN and OUT terminals are bridge connected auto termination NOTE Use the AUDIO A terminals for the corresponding au
3. COLOR VIDEO MONITOR BEDIENUNGSANLEITUNG FARB VIDEO MONITOR MANUEL D INSTRUCTIONS MONITEUR VIDEO COULEUR MANUALE DI ISTRUZIONI MONITOR VIDEO A COLORI INSTRUCCIONES MONITOR DE VIDEO A COLOR EHHE KERI S TM H150CG For Customer Use Enter below the Serial No which is located on the rear of the cabinet Retain this information for future reference Pour l usage du client Enter ci dessous le num ro de s rie qui est situ sur l arri re du coffret Conserver cette information pour une r f rence ult rieure Model No Num ro de mod le Serial No Num ro de s rie INSTRUCTIONS LCT1564 001A H I o Z TT FRANCAIS DEUTSCH ITALIANO Lad O lt A p TY INSTRUCTIONS COLOR VIDEO MONITOR TM H150CG I o Z TT Thank you for purchasing this JVC color video monitor Before using it read and follow all instructions carefully to take full advantage of the monitor s capabilities SAFETY PHECAUTIONS In order to prevent any fatal accidents caused by misoperation or mishandling the monitor be fully aware of all the following precautions WARNINGS To prevent fire or shock hazard do not expose this monitor to rain or moisture Dangerous high voltages are present inside the unit Do not remove the back cover of the cabinet When servicing the monitor consult qualified service personnel Never try to service it yourself WARNING THIS
4. 1 2 360 14 1 4 407 16 1 8 02050500 05050000 05050500 0050000 0 050000 0 0 050 295 5 11 3 4 310 12 1 4 2020202020 e e e e e Re d 164 6 1 2 Acceptable Signal Formats O Acceptable Not acceptable I o Z TT Terminals on the rear of the monitor PAL Black and White 50 Hz 60 Hz For details about each input card see pages 7 and 8 m Y C Mini DIN 4 pin terminals 2 4 CO lt Y C IN 1 3 2 4 1 3 19 2004 VICTOR COMPANY OF JAPAN LIMITED VICTOR COMPANY OF JAPAN LIMITED Printed in Thailand 0204MKH MW MT HOLINOIN O3GIA 40 109 920SLFH IN L
5. APPARATUS MUST BE EARTHED Improper operations in particular alternation of high voltage or changing the type of tube may result in x ray emission of considerable dose A unit altered in such a way no longer meets the standards of certification and must therefore no longer be operated This monitor is equipped with a 3 blade grounding type plug to satisfy FCC rule If you are unable to insert the plug into the outlet contact your electrician PRECAUTIONS e Use only the power source specified on the unit 120 V AC 220 240 V AC 50 Hz 60 Hz e When not using this unit for a long period of time or when cleaning it be sure to disconnect the power plug from the AC outlet e Do not allow anything to rest on the power cord And do not place this unit where people will tread on the cord Do not overload wall outlets or power cords as this can result in a fire or electric shock e Avoid using this unit under the following conditions in extremely hot cold or humid places in dusty places near appliances generating strong magnetic fields in places subject to direct sunlight in badly ventilated places in automobiles with doors closed e Do not cover the ventilation slots while in operation as this could obstruct the required ventilation flow e When dust accumulates on the screen surface clean it with a soft cloth FCC INFORMATION U S A only CAUTION Changes or modification not approved by
6. JVC could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Notice U S A only This product utilizes both a Cathode Ray Tube CRT and other components that contain lead Disposal of these materials may be regulated in your community due to environmental considerations For disposal or recycling information please contact your local authorities or the Electronics Ind
7. SET UP MENU CUTOFF G CUTOFF B CUTOFF R DRIVE B DRIVE CONTROL LOCK STATUS DISPLAY REMOTE SYSTEM INPUT REMOTE Picture Adjustment 11 I How to Use MENU MENU gt APERTURE 00 ADJ BAR POSI LOWER COLOR TEMP 9300 COLOR SYSTEM AUTO COMPO LEVEL 00 RUSH DELAY Function display of the button varies depending on the selected item Buttons Displays Functions 0v ov Selects the items in forward rotation VOLUME SELECT A Selects the items in reverse rotation Increases the value up to the maximum DESEE Selects the setting value in forward rotation VOLUME O Decreases the value up to the minimum SELECT Selects the setting value in reverse rotation MENU EXIT Exits from MENU CHFj2MA CONTRAST D IVOLUME SELECT OO DCS cs PHASE BRIGHT XX Function Contents and the Adjustment Range of Each APERTURE Adjusts the picture aperture level e 00 40 ADJ BAR POSI Selects the level bar position on the screen which appears when adjusting picture or volume e UPPER LOWER VOLUME 20 __ UPPER 7 VOLUME 20 OWER COLOR TEMP Selects the color temperature 9300 6500 Selects the color system AUTO Selects NTSC or PAL automatically depending on the input signal NTSC Keeps the NT
8. SYSTEM in MENU to AUTO selected Has BLUE CHECK or COLOR OFF Press the BLUE CHECK button or the COLOR 45 been activated OFF button to deactivate the functions Has CONTRAST or BRIGHT been Adjust CONTRAST or BRIGHT by using the front changed panel buttons Or adjust CONTRAST or BRIGHT in PICTURE SUB ADJ in SET UP MENU 4 11 13 11 14 on S NO Is the monitor close to a motor Move the monitor away from the device until the transformer or any other device picture stops shaking generating a strong magnetic field Connect the power plug to another AC outlet away a fan fluorescent light laser printer from the former one another monitor etc A Co Irregular color Wrong picture position Front panel buttons do not function Points to be checked Is the monitor placed or moved close to a speaker or any other device incorporating a magnet Has the position of the monitor been changed with the power on Has the picture position been changed Has the UNDER SCAN or ASPECT button been pressed Has the CONTROL LOCK function been set to Has the monitor s setting been changed to enable control by the external control connected to the REMOTE terminal The following are not malfunctions e When a bright still image such as a white cloth is displayed for a long period it may appear to be colored This is due to the structure of th
9. drive level adjustment R DRIVE sl 1 When DRIVE is selected BR DRIVE Adjusts the drive level of the red signal 20 gt 00 20 BB DRIVE Adjusts the drive level of the blue signal 20 2 00 gt 20 You can turn off the on screen display during the adjustment of the white balance by pressing the A button I How to Use SET UP MENU concra CONTROL LOCK Prohibits the monitor operations except turning on off the monitor and adjusting volume The menu operations are also prohibited ON Activates this function OFF Deactivates this function NOTES When CONTROL LOCK is set to ON CONTROL LOCK ON appears on the screen if you try to operate the monitor You can deactivate this function on SET UP MENU when CONTROL LOCK is set to ON STATUS DISPLAY If COLOR SYSTEM is set to AUTO you can display the color system NTSC or PAL of the current input signal when turning on the monitor or when changing the input ON Displays the color system NTSC or PAL of the current input signal OFF Does not display the color system NTSC or PAL of the current input signal NOTE The color system does not appear on the screen when the component signal RGB signal or black and white signal is input REMOTE SYSTEM Selects the method of the external control connected to the REMOTE terminal For details se
10. CHROMA to 40 is chroma off PHASE is adjustable only when the NTSC signal is input V button while the menu screen is displayed Selects the items on the menu screen CONTRAST B Contrast BRIGHT t Brightness button Press this button to activate the picture contrast adjustment mode or picture brightness adjustment mode Each time you press the button the adjustment modes change Contrastz Brightness Adjust the value with the VOLUME SELECT 14 buttons while the level bar appears on the Screen 40 to 40 A button while the menu screen is displayed Selects the items on the menu screen While adjusting the picture The adjustment level bar disappears if no operation has been done for about 10 seconds he adjustment level bar also disappears if you press MENU button e NO EFFECT will appear for about seconds if the function you select has no effect A B c Eni b OO L INPUT SELECT VOLUME SELECT 1 buttons Adjusts the volume These buttons are also used to select the items on the menu screen while the menu screen is displayed e Pressing or button displays the VOLUME level bar on the screen Pressing or button while the level bar appears on the screen allows you to adjust the volume 00 to 50 e The VOLUME level bar disappears if no operation has been done for about 10 seconds e The VOLUME level bar also disappears if y
11. EL RUSH DELAY CAE e 2 Press the A V button to select APERTURE lt MENU gt gt APERTURE ADJ BAR POSI COLOR TEMP COLOR SYSTEM COMPO LEVEL RUSH DELAY iE B Press the VOLUME SELECT buttons to adjust APERTURE lt MENU gt gt APERTURE ADJ BAR POSI COLOR TEMP COLOR SYSTEM COMPO LEVEL RUSH DELAY CAT 4 Press the MENU button to exit from MENU B Initializing the Settings You can initialize the following settings of the monitor MENU SET UP MENU picture adjustment volume level 7 Press the stand by button to turn off the monitor on stand by 2 While holding down both the MENU button and the V button press the stand by button to turn on the monitor NOTE Keep pressing both the MENU button and the V button until lt SET UP MENU gt RESET appears on the screen lt SET UP MENU RESET appears on the screen SET UP MENU RESET Are you sure Yes then lt gt No then MENU 3 Press the VOLUME SELECT button to initialize the settings The settings are initialized and lt SET UP MENU RESET disappears To cancel to initialize press the MENU button I o Z TT Initial settings Functions Items Initial settings 00 APERTURE ADJ BAR POSI COLOR TEMP COLOR SYSTEM COMPO LEVEL RUSH DELAY PICTURE SUB ADJ CONTRAST BRIGHT CHROMA PHASE H POSITION V POSITION WHITE BALANCE
12. SC color system PAL Keeps the PAL color system NOTE Normally select AUTO If the input signal is unstable select NTSC or PAL 12 COMPO LEVEL Adjusts the component level of the monitor for the component signal or the SDI signal 40 2 10 NOTE When inputting the component signal or the SDI signal check if COMPO LEVEL is adjusted properly for the standard color bar currently used For details see page 5 RUSH DELAY Sets the delay time between when the stand by button is pressed and when the monitor actually turns on e STD Power turns on about 1 second after the stand by button is pressed SLOW Power turns on about 3 seconds after the stand by button is pressed NOTE It is recommended to apply SLOW to some of the monitors if you need to turn on multiple monitors at the same time You can control the rush current of the entire system I How to Use SET UP MENU SET UP MENU gt PICTURE SUB ADJ H POSITION 00 V POSITION 00 WHITE BALANCE CONTROLLOCK OFF STATUS DISPLAY ON REMOTE SYSTEM MAKE INPUT REMOTE A D 1 EM CHF OMA CONTRAST IVOLUMEISELECT OO DCS PHASE BRIGHT Y f Function Contents and the Adjustment Range of Each PICTURE SUB ADJ The standard value 00 of the picture adjustment is initially set at the factory You can adjust the standard value as y
13. TOFF Adjusts the cut off point of the red signal G CUTOFF Adjusts the cut off point of the green signal B CUTOFF Adjusts the cut off point of the blue signal R DRIVE Adjusts the drive level of the red signal B DRIVE A Adjusts the drive level of the blue signal CONTROL LOCK Prohibits the monitor operations except turning on off the monitor and adjusting volume The menu operations are also prohibited STATUS DISPLAY Selects to display or not to display the color system of the current input on the screen REMOTE SYSTEM Selects the method of the external control connected to the REMOTE terminal INPUT REMOTE Sets how to change the input when operating the monitor by the external control 2 May not appear depending on the type of input signal Appears only when REMOTE SYSTEM is set to Displaying the menu screens To display MENU Press the MENU button on the front panel To display SET UP MENU Press the V button while holding down the MENU button on the front panel go back to the previous menu press the MENU button o exit from the menu screen press the MENU button several times NOTE The menu screen will disappear if no operation has been done for about 5 minutes Menu Operation Procedure Example When adjusting APERTURE to 10 1 Press the MENU button MENU appears on the screen lt MENU gt D APERTURE ADJ BAR POSI COLOR TEMP COLOR SYSTEM COMPO LEV
14. cy 15 734 kHz NTSC 15 625 kHz PAL V 59 94 Hz NTSC 50 Hz PAL Horizontal resolution 750 TV lines or more Y C input mode Input terminals VIDEO A Composite video 1 line BNC connector x 2 1 V p p 75 negative sync bridge connection possible auto termination VIDEO B Composite video 1 line BNC connector x 2 1 V p p 75 negative sync bridge connection possible auto termination Y C separated 1 line mini DIN 4 pin connector x 2 Y 1 V p p 75 C BURST 0 286 V p p 75 Q NTSC 0 3 V p p 75 PAL bridge connection possible auto termination AUDIO A 1 line monaural RCA pin x 2 0 5 V rms high impedance bridge connection possible 1 line monaural RCA pin x 2 0 5 V rms high impedance bridge connection possible Point of contact connection 1 line D sub connector 15 pin 3 line Operation temperature 5 40 41 F 104 F Operation humidity 20 96 80 96 non es Width 360 mm 1 4 Height 310mm 12 1 4 Depth 418mm 16 1 2 Weight 16 kg 35 2 1 5 not including input card e Illustrations used in this manual are for explanatory purposes only The appearance of the actual product may differ slightly Dimensions and weight are approximate E amp O E Design and specifications subject to change without notice Effective screen size 18 Dimensions Unit mm inch Asterisks are used to indicate the screen dimensions 418 16
15. des are the same CHROMA picture color density is adjusted properly For the component signal or the SDI signal if the brightness of the blue bars on the left and right sides are the same COMPO LEVEL is adjusted properly 4 If the brightness of two blue bars in the middle are the same PHASE picture hue is adjusted properly PHASE should be checked only when the NTSC signal is being input If the brightness of each blue bar is different make the following adjustment in the blue checking state When the composite signal or the Y C S video signal is being input By using the CHROMA PHASE button and the VOLUME SELECT 1 buttons adjust CHROMA or PHASE so that brightness of the blue bars on the left and right sides are the same When the component signal or SDI signal is being input Press the MENU button to display MENU select COMPO LEVEL by pressing the A V buttons Then adjust COMPO LEVEL by pressing the VOLUME SELECT 1 buttons so that brightness of two blue bars in the middle are the same e Be sure to adjust CHROMA for the composite signal or the Y C S video signal before adjusting COMPO LEVEL If you change the CHROMA adjustment for other signal formats than the component signal after COMPO LEVEL has been adjusted you need to adjust COMPO LEVEL again ASPECT button Changes the aspect ratio from 4 3 to 16 9 The button lights while the aspect ratio is 16 9
16. dio signals VIDEO B terminal Input IN and output OUT terminals for composite signals The IN and OUT terminals are bridge connected auto termination NOTE Use the AUDIO B terminals for the corresponding audio signals VIDEO B Y C IN Y C OUT terminal Input IN and output OUT terminals for Y C S video signals The Y C IN and Y C OUT terminals are bridge connected auto termination NOTES Use the AUDIO B terminals for the corresponding audio signals When both an Y C S video signal and a composite signal are input to the VIDEO B terminal the Y C signal has priority over the composite signal AUDIO A terminal Input IN and output OUT terminals for analog audio signals The IN and OUT terminals are bridge connected auto termination NOTE Use the VIDEO A terminals for the corresponding video signals 0509090509000 O 00 O 0505090 O_O O OP O 0520000 O 0 0 0 0000000000000 050 050 9 050 5 950525022202 OOOOO AUDIO B terminal Input IN and output OUT terminals for analog audio signals The IN and OUT terminals are bridge connected auto termination NOTE Use the VIDEO B terminals for the corresponding video signals Input card slot When using the input card not supplied install the card to t
17. e cathode ray tube and will disappear when another image is displayed e You may sometimes experience a mild electric shock when you touch the picture tube This phenomenon is due to a normal buildup of static electricity on the CRT and is not harmful he monitor emits a strange sound when the room temperature changes suddenly This is only a problem if an abnormality appears on the screen as well e If two or more monitors are placed close each other their images may shake or be distorted This phenomenon is due to mutual interference it is not a malfunction Move the monitors away from each other until the interference disappears or turn the power off on any monitor that is not being used Measures Remedy eid Move the device away from the monitor and turn off the monitor Wait at least 30 minutes then turn on the monitor Adjust POSITION or V POSITION in SET UP MENU When the UNDER SCAN or ASPECT button is lit press the button to deactivate the function Set the CONTROL LOCK function to OFF Change the setting of the external control so that the monitor can be operated by the buttons on the front panel 17 ENGLISH 1 Specifications MODEL TM H150CG Color system PAL NTSC 3 58 39 cm 15 measured diagonally Picture tube 90 deflection in line gun trio dot type phosphor dot trio pitch 0 27 mm Width 285 5 mm 11 3 16 Height 214 mm 8 3 8 Diagonal 356 mm 14 Scanning frequen
18. e page 15 MAKE make contact system e TRG trigger system INPUT REMOTE Sets how to change the input when operating the monitor by the external control For details see page 15 e A D A B NOTE INPUT REMOTE appears on the screen only when REMOTE SYSTEM is set to MAKE I How to Use the External Control B About the External Control This monitor has the REMOTE remote terminal that is used for the operation by an external control You can select the following control methods according to the setting of REMOTE SYSTEM in SET UP MENU MAKE make contact system Controls the function by short circuiting the corresponding pin terminal to the GND pin terminal or disconnecting opening it e TRG trigger system Controls the function by inputting the pulse signal instantaneously to the corresponding pin terminal NOTES When selecting MAKE the make contact system you can select how to change the input by the external control as follows A D 4 pin control Changes the input by short circuiting any one signal line of INPUT A to INPUT D 1 pin control Selects INPUT A or INPUT B by short circuiting and opening only 2nd pin terminal In this setting you cannot change the input to INPUT C or INPUT D by the external control Opening Changes the input to INPUT A Short circuiting Changes the input to INPUT B B How to Use the REMOTE Terminal No Functions to be controlled O
19. example if both the input IN and output OUT terminals are connected to the same VCR resonance may occur except during playback This is caused by that the same video signal circulates between the VCR and the monitor This is not a malfunction 1 Preparation Installing the Input Card 1 Turn off the main power switch on the rear panel of the monitor and unplug the AC power cord from the AC outlet 2 Unscrew the screws and remove the slot cover from the input card slot on the rear panel of the monitor Slot cover J Insert the input card s circuit board green colored into the slot fitting the board to the guide rails on the top and bottom of the slot Hold the tabs on the input card when inserting the input card Fit the board to the guide rails NOTE When installing IF C21SDG IF C51SDG you need to set the DIP switches on the input card correctly to use the functions of the input card Refer to the instruction manual supplied with the input card and set the DIP switches beforehand I o Z TT Guide rails SO le Input card This illustration is IF CO1COMG 4 Push in the input card so that its front panel touches the rear panel of the monitor D Secure the Input Card by using the screws removed in step 2 NOTES The input card or the monitor may be damaged if you do not turn off the main power of the monitor before installing the input card Do not touch
20. g audio signals The IN and OUT terminals are bridge connected I o Z TT I Controls and Features Input Card option cont d SDI Input Card IF C21SDG IF C51SDG The EMBEDDED AUDIO signal is acceptable IF C51SDG is also equipped with an AUDIO LEVEL METER function SWITCHED OUT terminal Output OUT terminal for the re clocked signal The input signal from the input terminal currently selected IN1 or IN2 is re clocked and output from this terminal NOTES No signal is output from the SWITCHED OUT terminal when the main power is turned off Even when the input signal is switched from the SDI Input Card the SWITCHED OUT terminal still outputs the IN1 or IN2 re clocked signal which is selected last time T The re clocked signal from IN1 is output from the SWITCHED OUT terminal when the ae monitor is in stand by mode D1 SDI and EMBEDDED AUDIO signal input terminals Accepts the SMPTE259M D1 SDI signal Also accepts the EMBEDDED AUDIO signal whose sampling frequency is 48 kHz and the channel range is 1 to 8 To select IN1 Press the INPUT SELECT C button To select IN2 Press the INPUT SELECT D button mE To select the EMBEDDED AUDIO channels and to set the AUDIO LEVEL METER This illustration is IF C21SDG function only for IF C51SDG set the DIP switches on the input card correctly For details refer to the instruction manual supplied with the input card sd
21. gger system operate each function by Pulse control that is short circuiting the corresponding pin terminal to the 15th pin terminal GND for about 1 second NOTES When selecting MAKE the make contact system You cannot use the following buttons on the front panel UNDER SCAN COLOR OFF ASPECT INPUT SELECT REMOTE ON appears on the screen if one of those buttons is pressed When more than one terminal of INPUT A to INPUT D are selected short circuited inputs are given the alphabetical priority B C D We recommend using an interlock switch which turns off a switch when another switch is turned on When selecting TRG the trigger system You can use the buttons on the front panel You can operate only one function at a time We recommend using a switch which turns on only while it is pressed down 15 16 I Troubleshooting Solutions to common problems related to your monitor are described here If none of the solutions presented here solve the problem unplug the monitor and consult a JVC authorized dealer or service center for assistance Points to be checked Measures Remedy No power supply Is the power plug loosened or Firmly insert the power plug disconnected No picture with the power on Wrong color Unnatural picture Shaking picture Is the main power turned OFF Turn the main power switch on 8 Is the signal cable disconnected Connect the signa
22. his slot REMOTE external control terminal Terminals for controlling the monitor by an external control For details see page 15 Main power switch Turns on and off the main power e ON O OFF NOTE When turning on the main power the power lamp lights up as follows e Orange The monitor is in stand by mode e Green The monitor is on AC inlet Connect the supplied AC power cord to this inlet and an AC outlet 120 V AC 220 240 V AC 50 60 Hz Input Card option Component RGB Input Card IF C01COMG 9 TY Acceptable signal formats when installed on this monitor 525 601 625 501 e on SYNC cannot be used with the RGB input Component RGB signal input output terminals Input IN and output OUT terminals for the component color difference or the RGB signal To select Component signal Press the INPUT SELECT C button To select RGB signal Press the INPUT SELECT D button The IN and OUT terminals are bridge connected auto termination Connection terminal Attach to the connection terminal of the input card slot on the monitor Synchronized signal input output terminals Input IN and output OUT terminals for the vertical horizontal or complex synchronized signals The IN and OUT terminals are bridge connected auto termination NOTE These terminals are available only to the RGB input Audio sig
23. l cable firmly 68 Is the power of the connected Turn on the power of the connected component component ON and set it correctly Is the signal output from the connected component Is the input selected correctly Select the correct input with the INPUT SELECT 5 buttons Is the input signal adapted to the Check if the input signal format is acceptable to n OMM 6 8 19 monitor s specification the monitor or the input card Is the audio cable disconnected Connect the audio cable firmly Is the audio signal output from the Set the connected component correctly connected component Is the volume output set to minimum Adjust the volume with the VOLUME SELECT buttons Has the picture adjustment been Set each picture adjustment to the standard changed level 00 Or set each item in PICTURE SUB ADJ in SET UP MENU to the standard level 00 Or initialize the settings of the monitor Has the WHITE BALANCE setting been Set each item in WHITE BALANCE in SET UP changed MENU to the standard level 00 Or initialize the settings of the monitor Are any cables disconnected from the Connect each signal cable firmly component RGB input card Has the correct signal been input to the Select INPUT C when the component signal is component RGB input card Has the input Select INPUT D when the RGB signal is correct INPUT been selected on the input monitor Has the correct color system been Set COLOR
24. minimum E 2 POSITION Lit Adjusts the horizontal position of the screen NOTE You can adjust H POSITION separately for each video input Select the video input you want to adjust beforehand 05 gt 00 05 Moves the screen the left Moves the screen to the right V POSITION Adjusts the vertical position of the screen NOTE You can adjust V POSITION separately for each video input Select the video input you want to adjust beforehand 05 00 gt 05 Moves the screen downward Moves the screen upward 13 14 WHITE BALANCE Adjusts the white balance NOTE You can adjust the items in WHITE BALANCE separately for each color temperature 6500 or 9300 Select the color temperature you want to adjust beforehand Cut off adjustment e Select WHITE BALANCE on SET UP MENU then press the VOLUME SELECT button to display the setting display for the cut off adjustment R CUTOFF 00 f When R CUTOFF is selected mh CUTOFF Adjusts the cut off point of the red signal 20 gt 00 20 CUTOFF Adjusts the cut off point of the green signal 20 2 00 20 CUTOFF Adjusts the cut off point of the blue signal 20 00 20 Drive level adjustment e Select WHITE BALANCE on SET UP MENU then press the VOLUME SELECT button to display the setting display for the
25. nal input output terminals Input IN and output OUT terminals for the analog audio signals The IN and OUT terminals are bridge connected NOTE You cannot connect both the component signal outputs and the RGB signal outputs at a time SDI Input Card IF C01SDG Acceptable signal formats when installed on this monitor 525 601 625 501 SWITCHED OUT terminal Output OUT terminal for the re clocked signal The input signal from the input terminal currently selected SDI 1 or SDI 2 is re clocked and output from this terminal NOTES No signal is output from the SWITCHED OUT terminal when the main power is turned off Even when the input signal is switched from the SDI Input Card the SWITCHED OUT terminal still outputs the SDI 1 or SDI 2 re clocked signal which is selected last time The re clocked signal from SDI 1 is output from the SWITCHED OUT terminal when the monitor is in stand by mode D1 SDI signal input terminal SDI 1 SDI 2 Accepts the SMPTE259M D1 SDI signal The audio signal of the EMBEDDED AUDIO signal cannot be decoded only the video signal can be decoded To select SDI 1 Press the INPUT SELECT C button To select SDI 2 Press the INPUT SELECT D button Connection terminal Attach to the connection terminal of the input card slot on the monitor Audio signal input output terminals for both SDI 1 and SDI 2 Input IN and output OUT terminals for the analo
26. ou press MENU button MENU button Displays MENU For details see page 10 NOTE To display SET UP MENU press the V button while holding down the MENU button UNDER SCAN button Reduces the screen size to display the entire image e The button lights while this function is activated e Pressing the button again restores the screen to normal SIZe 6 COLOR OFF button Cuts color signals to display a black and white image Use this function to check noises in the luminance signal or to check the white balance adjustment e The button lights while this function is activated e Pressing the button again restores the normal screen NOTE This function is not available to the RGB signal BLUE CHECK button Displays only the blue signals The button lights while this function is activated Pressing the button again restores the normal screen By using this function with the standard color bar currently used you can check if CHROMA picture color density or PHASE picture hue is adjusted properly Also you can check if COMPO LEVEL the adjustment level of the component signal is adjusted properly for the component signal or the SDI signal NOTE This function is not available to the RGB signal 1 Display the standard color bar currently used on the screen 2 Press the BLUE CHECK button The following display appears on the screen 3 If the brightness of the blue bars on the left and right si
27. our initial setting e Select PICTURE SUB ADJ on SET UP MENU then press the VOLUME SELECT button to display the setting menu illustrated on the right NOTES e You can adjust the items in PICTURE SUB ADJ separately for each video input Select the video input you want to adjust beforehand Only CONTRAST and BRIGHT appear on the screen when the HGB signal is input When the signal with PAL color system is input PHASE does not appear mCONTRAST 10 00 10 BBRIGHT 10 00 10 BCHROMA 10 00 10 BPHASE 10 00 10 lt PICTURE SUB ADJ gt CONTRAST 00 BRIGHT CHROMA PHASE Function and display of the button varies depending on the selected item Buttons Displays Functions v v _ Selects the items in forward rotation 4 Selects the items in reverse rotation VOLUME SELECT Selects the setting value in forward rotation VOLUME Decreases the value up to the minimum SELECT Selects the setting value in reverse rotation MENU EXIT Returns to or exits from SET UP MENU When setting WHITE BALANCE Buttons Displays Functions RB Selects the color to adjust the drive level Selects the color to adjust the cut off point 4 DISP Turns on screen displey VOLUME SELECT VOLUME SELECT Decreases the value up 10 the
28. pening Short circuiting 1 Notin use 2 Changes the input to INPUT A Invalid Valid 1 3 Changes the input to INPUT B Invalid Valid 2 4 Changes the input to INPUT C Invalid Valid 2 um 5 Changes the input to INPUT D Invalid Valid 2 2 6 Notin use 14 7 Notinuse T 12 2 8 COLOR OFF Off On 9 Notinuse REMOTE 10 ASPECT Off 4 3 On 16 9 termina 14 UNDER SCAN Off On 12 Notin use 13 Notin use 14 External control Invalid Valid 3 4 15 GND 1 The 2nd pin terminal works to change the input between INPUT A opening and INPUT B short circuiting when INPUT REMOTE in SET UP MENU is set to 2 These pin terminals are not in use when INPUT REMOTE in SET UP MENU is set Do not connect these pin terminals in such a case 3 The 14th pin terminal External control should be controlled by the make contact system even when selecting TRG the trigger system 4 Short circuiting the 14th pin terminal External control enables operating other functions listed above by the external control Operation 1 Short circuit the 14th pin terminal External control to the 15th pin terminal GND so that the monitor can be controlled by the external control 2 When selecting MAKE the make contact system operate each function by short circuiting the corresponding pin terminal to the 15th pin terminal GND or opening it When selecting TRG the tri
29. s Use only the power cord designated to ensure Safety and EMC regulations of each countries Power cord Power supply voltage AC 120 V AC 220 240V AC 220 240 V Countries U S A and Canada European countries United Kingdom Warning e Do not use the same Power Cord for AC 120 V as for AC 220 240 V Doing so may cause malfunction electric shock or fire Note for the United Kingdom power cord only The plug on the United Kingdom power cord has a built in fuse When replacing the fuse be sure to use only a correctly rated approved type re fit the fuse cover Consult your dealer or qualified service personnel How to replace the fuse Open the fuse compartment with the blade screw driver and replace the fuse An example is shown in the illustration SCREEN BURN e t is not recommended to keep a certain still image displayed on screen for a long time as well as displaying extremely bright images on screen This may cause a burning sticking phenomenon on the screen of cathode ray tube This problem does not occur as far as displaying normal video playback motion images ll Supplementary Explanation Information for monitor operation This monitor uses a high precision CRT cathode ray tube Please follow the procedures below For stable operation of the CRT approximately 30 minutes running time is required from the time the power is turned on When the monitor is installed it can be easily affected b
30. the terminals or the patterns on the circuit board of the input card Attach the slot cover when the input card slot is not in use 10 1 Basic Menu Operations MENU SET UP MENU About the Menu Screens This monitor features MENU which contains the functions normally used and SET UP MENU which contains the initial settings of the monitor MENU Items Functions APERTURE Adjusts the picture aperture level ADJ BAR POSI Selects the level bar position on the screen which appears when adjusting picture or volume COLOR TEMP Selects the color temperature COLOR SYSTEM Selects the color system COMPO LEVEL Adjusts the component level of the monitor for the component signal or the SDI signal RUSH DELAY Sets the delay time between when the stand by button is pressed and when the monitor actually turns on Appears only when the component signal input or the SDI signal input is selected when INPUT C or INPUT D is selected and other signals than RGB is input SET UP MENU Items Functions PICTURE SUB ADJ The standard value 00 of the picture adjustment is initially set at the factory You can adjust the standard value as your initial setting CONTRAST Adjusts contrast BRIGHT Adjusts brightness CHROMA Adjusts color density PHASE Adjusts hue H POSITION Adjusts the horizontal position of the screen V POSITION Adjusts the vertical position of the screen WHITE BALANCE Adjusts the white balance CU
31. ustries Alliance lt http www eiae org gt e Unplug this unit from the AC outlet and refer servicing to qualified service personnel under the following conditions when the power cord is frayed or the plug is damaged if liquid has been spilled into the unit if the unit has been dropped or the cabinet has been damaged when the unit exhibits a distinct change in performance e Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards Always refer servicing to qualified service personnel e When replacement parts are required have the service personnel verify in writing that the replacement parts he she uses have the same safety characteristics as the original parts Use of manufacture s specified replacement parts can prevent fire shock or other hazards e Upon completion of any servicing or repair work to this unit please ask the service personnel to perform the safety check described in the manufacturer s service literature e When this unit reaches the end of its useful life improper disposal could result in a picture tube implosion Ask qualified service personnel to dispose of this unit POWER CONNECTION The power supply voltage rating of this product is AC 120 V For U S A and Canada only and AC 220 240 V For European countries or United Kingdom the power cord attached conforms to the following power supply voltage and countrie
32. y surrounding magnetic fields which can generate irregular color on the screen When it is difficult to eradicate degauss from outside using a degausser etc I o Z TT SAFETY PRECAUTIONS Nra Ke 2 Controls and Features 040 quu ENAESSRE RAS EAQUE 4 ON Ric MT 4 R PARER cC 6 INDUC ODOM 7 Preparato N eet m 9 Me rare en 9 Basic Menu Operations MENU SET UP MENU 10 How to Us MENU ss opa ee oo er vu vx Cau epu a lt we xxu PE VES 12 How to Use SET UP MENU 13 How to Use the External 15 icu M 16 amp eee 18 I Controls and Features Front Panel iJ CHROMA CB Chroma PHASE s4 Phase button Press this button to activate the Chroma picture color density adjustment mode or the Phase picture hue adjustment mode Each time you press the button the adjustment modes change Chroma Phase Adjust the value with the VOLUME SELECT 14 buttons while the level bar appears on the Screen 40 to 40 CHROMA is not adjustable when the RGB signal black and white signal or no signal is input except the component signal Adjusting
Download Pdf Manuals
Related Search