JVC SX-XD55J User's Manual
Contents
1. e To prevent deformation or discoloration of the cabinet do not install the speakers where they are exposed to direct sunlight or high humidity and avoid installation near air conditioning outlets e Speaker vibrations may cause howling Place the speakers as far away from the player as possible e The speakers are magnetically shielded to avoid color distortions on TVs However if not installed properly it may cause color distortions So pay attention to the following when installing the speakers When placing the speakers near a TV set turn off the TV s main power switch or unplug it before installing the speakers Then wait at least 30 minutes before turning on the TV s main power switch again Some TVs may still be affected even though you have followed the above If this happens move the speakers further away from the TV e Tuner reception may become noisy or hissing if a speaker is installed near the tuner In this case leave more distance between the tuner and the speakers or use an outdoor antenna for better tuner reception without interference from the speakers W Precautions for Daily Use e To maintain the appearance of the speakers Wipe with a dry soft cloth if the cabinet or control panel should become dirty If very dirty apply a small amount of water or neutral detergent to the cloth and wipe clean then wipe with a dry cloth Speaker and Speaker cords to improve the sound quality About DD Dire2. speaker cord into the speaker terminal 6 Insert the speaker cord into the speaker terminal inside the leg 3 Release 2 Insert y Speaker 1 Press section Red Biak Y 2 Insert ac Ve A a Copper we Black striped 3 Release Leg
3. 282 mm x 1 108mm x 282 mm 11 s in x 43 s in x 11 1 s in 3 0 kg 6 7 lbs each Type Speaker unit Mass 2 EN 2004 Victor Company of Japan Limited SX XD55C Center speaker 1 way 2 speaker bass reflex type magnetically shielded type Speaker unit 5 5 cm 2 16 in cone x 2 Frequency range 80 Hz to 20 000 Hz Input impedance 6Q Power handling Capacity 100 W Sound pressure level 79 dB Wem Dimensions WxHxD 200mm x 78mm x 120 mm 7 s in x 3 t s in x 4 3 4 in 0 85 kg 1 9 Ibs Type Mass 0304NSMMDWHCE LVT1203 001A J UJ JVL SX XD55 Home Theater DD Speaker System INSTRUCTIONS For Customer Use Enter below the Model No and Serial No which are located either on the rear bottom or side of the cabinet Retain this information for future reference Model No DD Speaker Serial No Consists of SX XD55F and SX XD55C Thank you for purchasing a JVC speaker system Before you begin using these speakers please read the instructions carefully W Precautions for installation Do not install the speakers on an uneven surface or in a place subject to vibration otherwise they may fall over causing damage or injury Take the occurrence of earthquakes or other physical shocks into consideration when selecting the installation place and secure the speakers thoroughly
4. Additional Information W Connecting the speaker system to the amplifier Before connecting e Turn off the power to the amplifier before connecting the speaker system otherwise the speakers may be damaged e The impedance of each speaker is 6 Q Before connecting them to your amplifier check the speaker impedance range of your amplifier If the impedance of this speaker is out of the speaker impedance range indicated on the amplifier you cannot connect this system to the amplifier e The maximum power handling capacity of the SX XD55 is 100 W Excessive input will result in abnormal noise and possible damage e Be sure to turn down the volume level to prevent unwanted noise before performing following operations Turning on or off other components Operating the amplifier Tuning FM stations Fast forwarding a tape Continuously reproducing high frequency oscillation or high pitch electronic sounds e When using a microphone do not aim it at the speakers or use it near the speakers otherwise the howling which occurs may damage the speakers e Before replacing the cartridge always turn off the power to the turntable otherwise the clicking noise may damage the speakers W General layout of speakers Place all speakers at the same distance from the listening position if possible e Usually place the center speaker close to the TV e When you place the center speaker on a TV make sure the s
5. FC Oxygen Free Copper This OFC cord enables high quality sound reproduction When connecting the speaker cords Make sure to match the polarity and otherwise the surround effect will become less effective After connecting check that the exposed cores are fully inserted into the terminal When using other speaker cords Observe the following e Buy thick speaker cords rather than thin cords and make them as short as possible for connection e Use speaker cords of the same length for both left and right speakers e Do not use long speaker cords otherwise the sound quality may deteriorate Assembly Mi Assembling the satellite speakers Each speaker except the center speaker has been divided into three parts for shipment Before using this speaker system assemble it first by following the procedure below Speaker t section Leg e Prepare a Phillips screw driver Stand Before assembling e Take care not to drop the stand while assembling otherwise it may cause damage to the floor or injury e Ensure enough space for assembly and installation e Place a large thick cloth on the floor where you assemble the speaker so you can protect the floor and the speaker itself e Use the speaker only after assembly is fully and correctly done Attaching the leg and the stand Remove the terminal cover from the leg First remove the screw on the terminal cover then detach the cove
6. ct Drive speaker e To improve the sound field If the speakers are facing a solid wall or glass door etc it is recommended to furnish the wall with materials that absorb sounds for example by hanging up thick curtains to prevent reflections and standing waves e To use the speakers without any trouble Do not reproduce sounds at so high a volume that they are distorted otherwise the speakers may be damaged by internal heat buildup When moving the speakers do not pull the speaker cords otherwise the speakers may fall over causing damage or injury a When holding a satellite speaker do not grasp the speaker upper portion but always grasp the leg lower portion of the satellite speaker Leg Speaker cord Satellite speaker W Checking the supplied Accessories Check to be sure you have the following supplied accessories The number in parenthesis indicates the quantity of the piece supplied Speaker cords 6 m 19 7 ft 3 For front left right and center speakers 15 m 49 2 ft 3 For surround left right and surround back Speakers e Screws g M5 x 12 mm M5 x 2 in 5 M4 x 25 mm M4 x 1 in 15 e Washers 5 If any of the items above are missing contact your dealer immediately DD Direct Drive technology improves sound localization and transmits the powerful sounds About the OFC cord The core wires of the supplied speaker cords are made of O
7. r by pulling it upward e You will need to use the removed screw in step 5 2 ry AS Terminal cover 2 Join the leg to the stand DD Speaker and the IMG mark on the stand are facing the same direction e Make sure to match the screw holes on the leg with those on the stand so that they are aligned correctly Stand JVC mark 3 Fix the leg to the stand with three of the supplied screws long M4 x 25 mm M4 x 1 in Stand oy Screw e Do not tighten each screw completely one by one First put all screws in then tighten them evenly and firmly It is recommended to place a cushion under the leg e You can tighten the screws easily by placing the leg horizontally Cushion 4 Connect the speaker cord to the speaker terminal of the leg e Use the 6 meter 19 7 ft speaker cords for front speakers and 15 meter 49 2 ft soeaker cord for rear speakers e Each speaker cord has its name tag attached to one end Attach the end without the name tag to the speaker terminal e Twist and remove the insulation at the end of each speaker cord before connecting p othe speaker terminal of the leg 1 insert the speaker cord inside the stand as illustrated e Pull the speaker cord out of the center of the stand by about 50 cm 20 in The cord with the black stripe is on this side as illustrated Y Stand 2 insert the tips of the speaker co
8. rd into the leg and pull them out as illustrated Do not pull or remove the cord protector otherwise the speaker cord may come off from terminal on the leg or the speaker may be damaged Pa Speaker section PAREC N Cord protector _ Leg 3 insert the speaker cord into the speaker terminal inside the leg Join the speaker section and the leg Insert the speaker section to the leg then fix the speaker section and the leg with one of the washers and one of the supplied screws short M5 x 12 mm M5 x 2 in e Push cords fully inside the leg before attaching the speaker section 1 Press 2 Insert Speaker section Joint here without gap Black striped 9 Attach the terminal cover to the leg Push cords fully inside the leg Then fix the terminal cover using the screw removed in step 7 8 Repeat the procedure from step 7 to assemble the other satellite speakers For disassembly Reverse Assembly procedure 1 Remove the speaker section from the leg 2 Remove the leg from the stand Ql Screw T ln 2 ID p VESON va Terminal W Connecting the center speaker wy cover e To connect the center speaker use the same type of speaker cord 6 m 19 7 ft tagged with CENTER as used for connecting the front speakers e Twist and remove the insulation at the end of each speaker cord before connecting eona AG Ved AANE SEAE unt Insert the
9. urface is level and stable For a subwoofer JVC s SP DWF10 is recommended This combination gives you the best possible high quality surround sounds Do not lean against the speakers as the speakers could fall down or break possibly causing an injury Especially be careful that children do not lean against them W Typical connection method to an amplifier Connect the speakers to a speaker terminal of the amplifier with the speaker cords by referring to the diagram on the left e Make sure to match the polarity G and when connecting the speaker cords Center speaker SPEAKERS f FRONT CENTER SURROUND suarouno RIGHT LEFT RIGHT LEFT BACK Front left speaker Front right speaker Speaker terminals on the amplifier Surround left speaker Surround right speaker SURROUND LEFT Surround back speaker Front left speaker Front right speaker Subwoofer Listening position Surround left 7 speaker Surround back speaker Surround right speaker Specifications SX XD55F Satellite speaker 1 way 2 speaker bass reflex type magnetically shielded type Direct drive 9 5 cm x 1 cm 3 3 4 in x he in x 2 Frequency range 130 Hz to 20 000 Hz Input impedance 6Q Power handling Capacity 100 W Sound pressure level 80 dB Wem Dimensions WxHxD
Download Pdf Manuals
Related Search