Home

JVC SR-V10E User's Manual

Contents

1. Recording Resume Function If there is a power outage during recording Repeat Recording I pg 21 Series Recording gt pg 26 or timer recording F pg 28 30 32 the recording will resume automatically when power is restored to the recorder if the lithium battery is not exhausted 19 i Load a cassette Insert a cassette with the record safety tab intact If the tab has been removed set REC SAFETY to OFF lt pg 48 The recorder checks the tape information for Programme Navigation For details refer to Navigation C pg 36 Choose a programme Press PR or the number keys Or push the JOG dial and turn it to the left or right to select the channel you wish to record Set the tape speed Press SP LP EP The current setting appears on the front display panel or TV screen Press SP LP EP again to change the setting while the tape speed is displayed on the TV screen In EP mode the recording time is extended three times If you record a programme in EP mode on this recorder it is recommended to play back the EP recorded tape on this recorder It is not possible to select EP mode if COLOUR SYSTEM is set to gt pg 48 4 Start recording Press and hold and press on the remote control press on the recorder e If O S D REC
2. e ci I mM _ E m indicator NOTES To disengage the Automatic Satellite Programme Recording mode press REC LINK The indicator goes off If the recorder s power is off it is not possible to engage the Automatic Satellite Programme Recording mode In step 2 if the K indicator does not light but instead blinks quickly even though your satellite receiver s power is off Automatic Satellite Programme Recording will not work properly with that satellite receiver If this is the case perform Express Timer Programming I pg 30 to timer record a satellite programme Some satellite receivers output signals even if the power is off Automatic Satellite Programme Recording is not possible with those satellite receivers The K indicator blinks while Automatic Satellite Programme Recording is in progress For timer programming of the satellite receiver refer to the instruction manual of the satellite receiver Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer Pressing the recorder s button while Automatic Satellite Programme Recording is in progress turns off the recorder s power and disengages the Automatic Satellite Programme Recording mode If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Record
3. 19 59 59 If the playback or recording time exceeds this limit the display starts to count from 0 00 00 Tape Speed SP LP EP F pg 19 ON SCREEN DISPLAY EN 7 When O S D PLAY is set to ON gt pg 46 various operational indicators appear the TV screen if you press OK They also appear for 5 seconds when the playback starts Press OK again to clear the indicators When O S D REC is set to ON r pg 45 the operational indicators displayed on the TV screen will be recorded Set O S D REC to OFF if you do not want to record these indicators WARNING TIMER RECORDING TO a Operation Mode Indicators Tape Speed SP LP EP Tape Direction Index MARK Indicator c pg 19 Q Counter Display Tape Remaining Time Indicator gt pg 21 udio Mode Display gt pg 18 Q Tape Position Indicator The tape position indicator appears on the TV screen when you press lt or WP from the Stop mode or perform an Index Search I pg 17 The position of W in relation to 0 beginning or end 1 23 45 shows you where you REMAIN 2 35 on the tape NOTE Depending on the type of tape being used the tape position indicator may not appear correctly Beginning End Q VPS PDC Indicator gt pg 29 31 Type of Broadcast gt pg 22 Channel Position Number and Station Name Auxiliary Input Indicator L 1 F 1 S 1 or
4. By pressing the button you can change display to show the channel position clock time counter reading or tape remaining time Channel position is not displayed during playback NOTE Depending on the type of tape being used the tape remaining time reading may not appear right away or is not correct may sometimes appear or the display may blink on occasion en 21 Repeat Recording You can record programmes on one tape repeatedly Start recording Press and hold and press on the remote control or press on the recorder 2 Activate Repeat Recording Press and hold and press gt on the remote control or press on the recorder for over 5 seconds The Record indicator O on the front display panel blinks slowly 3 Stop Repeat Recording Press on the remote control on the recorder at any time Pressing also stops Repeat Recording NOTES Recording will be performed in LP mode even if the tape speed is set to EP mode when you start recording It is possible to use the Mode Lock function I pg 20 22 Super VHS ET S VHS ET Recording on VHS cassettes with S VHS quality You can record in SP mode on VHS cassettes with S VHS picture quality You can play back a tape recorded using the S VHS ET function on most of S VHS recorders and of VHS recorders equipped with SQPB S VHS QUASI PLAYBACK functio
5. Audio video cable not provided nn o Audio video input connectors NOTE Series Recording is also possible with the front AUDIO VIDEO or AUDIO S VIDEO input connectors Using two sets of SR V10E a long recording will be possible such as camcorder recording another recorder playback or TV broadcast NOTE Use the buttons and controls on the recorder for the Series Recording operations except when using Mode Lock gt pg 20 Make connections Connect two sets of SR V10E to other device antenna or cable as illustrated on page 26 The mini plug cable is a mono 3 5 mm mini plug to mono 3 5 mm mini plug connector When connecting a camcorder or another recorder with an S VIDEO output connector as recording deck it is recommended to use the S VIDEO connection to obtain the high quality pictures Turn on all components After completing the connections turn on all the components Set your TV to the VIDEO or AV mode Refer to the TV instruction manual Set the input mode on both SR V10E Turn the JOG dial to the right or left on each SR V10E to select the appropriate input mode depending on the connectors being used L 1 for the rear AUDIO VIDEO IN connectors F 1 for the front AUDIO VIDEO input connectors 5 1 for the rear AUDIO S VIDEO IN connectors 2 for
6. With AV or S VIDEO Connection To view picture signals from the video recorder set your TV to its AV mode With RF Connection The channel on which the TV screen in step 3 appears clearly is your video channel To view picture signals from the video recorder set your TV to the video channel TROUBLESHOOTING EN 59 Before requesting service for a problem use this chart and see if you can repair the trouble yourself Small problems are often easily corrected and this can save you the trouble of sending your video recorder off for repair POWER SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1 No power is supplied to the recorder The mains power cord is disconnected Connect the mains power cord 2 The clock is functioning properly but the recorder cannot be powered is displayed on the front display panel with AUTO TIMER set to OFF Press the button to turn the indicator off 3 The remote control won t function The batteries are discharged Replace the dead batteries with new ones TAPE TRANSPORT SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1 During recording the tape does not run Lon lights up and the channel display blinks on the front display panel The recorder is in the Record Pause mode Press to resume recording 2 The tape will not rewind or fast forward The tape is already fully rew
7. Engage the Play mode of the source player H Start the recording deck Engage the Record mode of the recording deck NOTES All necessary cables can be obtained from your dealer When you select EDIT to dub tapes in step 3 be sure to select AUTO or NORM when B E S T is set to OFF after you finish dubbing the tapes When you use this recorder as the source player for editing be sure to set O S D PLAY to OFF before starting gt pg 46 When you use this recorder as the recording deck for editing set O S D PLAY and O S D REC to OFF F pg 45 46 if you do not want to record the operational indicators displayed on the TV screen It is also possible to use the front AUDIO VIDEO or AUDIO S VIDEO input connectors for the connection When you use the front connectors select F 1 for the AUDIO VIDEO input connectors 5 2 for the AUDIO S VIDEO input connectors in step 2 gt 42 SYSTEM CONNECTIONS Connecting To A Satellite Receiver Connect the satellite receiver to the AUDIO VIDEO IN or NOTES S VIDEO IN connectors then connect the AUDIO You cannot use Automatic Satellite Programme Recording VIDEO OUT or VIDEO OUT connectors to the TV s function if you connect the satellite receiver and the recorder connectors with S video cable gt pg 35 record a programme via the satellite receiver select L 1 or S 1 m
8. EN 35 e Au to m q C q te te iplb dis on the satellite receiver before the programme is executed otherwise the recorder will start recording when the satellite receiver s power is turned on It is not possible to perform Automatic Satellite Programme p rog ra m m e Recording via S VIDEO IN connector gt pg 42 e Automatic Satellite Programme Recording and timer recording cannot be done at the same time e R eco rd n g Before performing the following steps Make sure the satellite receiver is connected to the recorder s This function allows you to automatically record a AUDIO VIDEO IN connectors I pg 42 satellite programme which is timer programmed on your ps iU EE desi external satellite receiver Connect a satellite receiver to Een REC en to ORE EF P d the recorder s AUDIO VIDEO IN connectors and ps programme the timer on the satellite receiver The recorder starts or stops recording by the signals input Hl Set the tape speed from the satellite receiver After recording the recorder s power shuts off automatically Press SP LP EP It is not possible to select EP mode if COLOUR SYSTEM is REC LINK set to MESECAM pg 48 Engage the Automatic Satellite Programme Recording mode Press and hold REC LINK for about 2 seconds The indicator lights up and the recorder turns off 7 automatically
9. light up on the front display panel No buttons will function and recording will not be interrupted until the recording ends To cancel Mode Lock press and hold OK again for more than 5 seconds When OK is pressed to set Mode Lock the on screen display appears and the time counter remains on the TV screen If the time counter is not necessary set O S D PLAY and O S D REC to OFF F pg 45 46 NOTE It is also possible to use Mode lock during Repeat Recording C pg 21 and Series Recording gt pg 26 Accidental erasure prevention To prevent accidental recording on a recorded cassette remove its safety tab To record on it later cover the hole with adhesive tape or set REC SAFETY to OFF 5 pg 48 2 Record safety tab Elapsed Recording Time Indication 1 Set the counter display Press until a counter reading appears on the front display panel The front display panel shows the counter reading with T Ef opo 2 Reset the counter Press 0000 before starting recording or playback The counter is reset to 0 00 00 and shows the exact elapsed time as the tape runs You can check the exact time of a recording or playback Tape Remaining Time Press until the time remaining on the tape appears The front display panel shows the tape remaining time with i blinking kh LI
10. using this video recorder as the source player for editing NOTES you play back a tape recorded under poor TV reception condition the picture may become more stable with Digital TBC NR set to off e When DIGITAL TBC NR is set to ON if you play back a tape where certain types of signals are recorded using a PC or some character generators the playback picture may be distorted If this is the case set DIGITAL TBC NR to OFF e When playing back a MESECAM tape Digital TBC NR does not function even though DIGITAL TBC NR is set to ON B E S T ON OFF You can set the B E S T Biconditional Equalised Signal Tracking system to ON or OFF F pg 23 PICTURE CONTROL AUTO EDIT SOFT SHARP This feature helps you to adjust the playback picture quality according to your preference Normally select AUTO AUTO Provides the optimised picture benefits of the B E S T Picture System EDIT Minimizes picture degradation during editing recording and playback SOFT Reduces image coarseness when viewing overplayed tapes containing a lot of noise Clearer sharper edged picture when viewing images with lots of flat same coloured surfaces such as cartoons SHARP NOTES e When you select EDIT SOFT or SHARP the selected mode will not change until you select another mode When you select EDIT to dub tapes be sure to select AUTO after you finish dubbing the ta
11. 35 41 42 IN Connector gt pg 10 REMOTE IN Connector gt pg 24 26 For the Remote Control Unit RM G30 not provided RF OUT Connector pg 10 service life will be drastically shortened Be sure to connect the power plug to an main outlet first before installing the lithium battery otherwise the battery s Make sure that the power plug is connected to an main outlet and turn off the recorder power Open the battery cover while pressing the release tab as illustrated Insert a lithium battery with the plus side up and push it in To remove the lithium battery press the latch 9 downward using a pointed non metallic object then pull out the lithium battery Close the battery cover until it clicks in place FRONT DISPLAY PANEL INDEX cont Instant REVIEW Indicator c pg 17 Start Time Indicator gt pg 17 20 30 32 S VHS Indicator gt pg 22 47 Stop Time Indicator 9 c pg 17 20 30 32 Q Channel Clock Remain Display Mode Display L 1 F 1 S 1 or S 2 Timer Indicator gt pg 29 31 32 Automatic Satellite Programme Recording Indicator gt pg 35 Q Play Indicator Q Record Indicator Counter Display The counter can display up to
12. 4 5 Return to the normal screen display 7 8 Press as many times as necessary If there are still some programmes remaining go on to step 8 021 NEXT Return to the timer mode H H H Press TIMER NOTE 1 You can also check the programmes on the front display panel Access the Programme screen display even if the recorder s power is off unless the recorder is in the Press again to check Power Save mode pg 47 however it is not possible to more information Each time cancel or change the programmes START STOP you press the next 10 00 programme s information appears SP VPS PDC OFF DATE TVPROG WDR 24 12 1 TITLE 6 NEXT The front display panel shows the programme number Pressing OK changes the display to the programme start time the stop time the date the tape speed then the channel position 34 TIMER RECORDING cont When programmes overlap each other If PROGRAM OVERLAPPED appears you have another programme overlapping the programme you have just made The Programme Check screen appears and conflicting programmes will start blinking START STOP 8 00 10 00 3 2412 10 00 10 45 2 25 12 11 30 13 00 1 25 12 9 00 10 00 92 DAILY PROGRAM OVERLAPPED 2 3 4 5 6 7 8 Av PROG EXIT Example Programme 1 you have just made a
13. 46 NOTE It is also possible to use Mode lock during Repeat Playback pg 18 and Series Playback gt pg 24 18 Next Function Memory The Next Function Memory tells the recorder what to do after rewinding Before continuing make sure the recorder is in the Stop mode a For Automatic Start Of Playback Press 4 4 then press within 2 seconds b For Automatic Power Off Press 4 then press within 2 seconds c For Automatic Timer Standby Press 4 4 then press TIMER within 2 seconds NOTE The Automatic Power Off does not work if AUTO TIMER is set to ON pg 45 and if any timer programming has been made The recorder directly goes into the Timer Standby mode after rewinding a tape Repeat Playback Your recorder can automatically play back the whole tape repeatedly Start playback Press 2 Activate Repeat Playback Press and hold for over 5 seconds then release The Play indicator on the front display panel blinks slowly 3 Stop Repeat Playback Press at any time Pressing lt lt BP or IIl also stops Repeat Playback NOTES Repeat playback is not possible with a cassette recorded in EP mode select the returning point recording end or tape end see RETURN POINT gt pg 48 It is possible to use the Mode Lock function F pg 17 PLAYBACK cont Manual Tracking Your recorder is equipped with automati
14. If a VPS PDC signal is detected from the station VPS PDC will stop blinking If no VPS PDC signal is detected from the station VPS PDC will blink at a slower rate Press or START again to return to normal display 2 24 Hour Express Timer Programming Before performing the 24 Hour Express Timer Programming Make sure that the recorder s built in clock is set properly Insert a cassette with the safety tab in place If the tab has been removed set REC SAFETY to OFF pg 48 The recorder will come on automatically NOTES You can programme this recorder to timer record as many as 8 programmes If you try to programme the recorder to record a ninth FULL appears on the front display panel To record the extra programme you must first cancel any unnecessary programmes 7 pg 33 e If Err appears on the front display panel repeat the above steps again When a menu screen is shown you cannot use 24 Hour Express Timer Programming function Press MENU to return to normal screen and try again You can use 24 Hour Express Timer Programming function also when the recorder is turned off For 24 Hour Express Timer Programming function the programme overlap warning display does not appear even if some programmes overlap each other The programme with t
15. MENU EXIT H Input the channel Press the number keys to input the channel number you want to store Input 0 before any single number entries To input the registered station name ID CF pg 55 press gt until ID setting begins blinking then press AV For fine tuning adjustment press gt until begins blinking uo then press AV While tuning or appears m Enter new channel information Press OK and the Confirmation screen appears Repeat steps 3 6 as necessary Close the Confirmation screen Press MENU To change positions see Change Station Channel Position gt pg 53 If you wish to set station names other than the ones registered in your recorder see Set Stations B I pg 54 ATTENTION Guide Program numbers are not set when channels are stored manually If an attempt is made at timer programming with the SHOWVIEW system in this state the GUIDE PROG SET screen appears set the Guide Program numbers on this screen I pg 29 ATTENTION Guide Program Number Set Or perform Guide Program Number Set F pg 49 Delete A Channel EN 53 Change Station Channel Position Perform steps 1 and 2 of Manual Channel Set on page 52 to access the Confirmation screen before continuing Perform steps 1 and 2 of Manual Channel Set on page 52 to access th
16. SELECT LETTERS X DELETE 4 gt 1 CURSOR OK PROG EXIT Return to the normal screen Press PROG or OK PROGRAM COMPLETED appears on the TV screen for about 5 seconds then the normal screen appears If PROGRAM OVERLAPPED appears on the TV screen and Err on the front display panel see page 34 Repeat steps 1 11 for each additional programme EN 31 iE Engage the recorder s timer mode Press TIMER The recorder turns off automatically and appears on the front display panel To disengage the timer mode press TIMER again To Timer Record Weekly Or Daily Serials anytime during steps 2 through 8 press WEEKLY number key 9 for weekly serials or DAILY number key 8 for daily serials Sunday Saturday Either WEEKLY or DAILY appears on the TV screen Pressing the button again makes the corresponding indication disappear NOTES You can programme this recorder to timer record as many as 8 programmes If you try to programme the recorder to record a ninth PROGRAM FULL appears on the TV screen and FULL appears on the front display panel To record the extra programme you must first cancel any unnecessary programmes gt pg 33 e Even if a power failure occurs the recorder keeps your timer programmes if the lithium battery is not exhausted Satellite Receiver Users To timer record a satellite broadcast
17. safety tab removed and REC SAFETY is set to ON Load a cassette with the record safety tab intact If the tab has been removed set REC SAFETY to OFF I pg 48 Set REC SAFETY to OFF pg 48 or using adhesive tape cover the hole where the tab was removed 2 TV broadcasts cannot be recorded e 1 1 F 1 S 1 5 2 has been selected as the input mode Set to the desired channel 3 Tape to tape editing is not possible The source another video recorder camcorder has not been properly connected All necessary power switches have not been turned on The input mode is not correct Confirm that the source is properly connected Confirm that all units power switches are turned on Set the input mode to L 1 F 1 S 1 or 5 2 4 Camcorder recording is not possible The camcorder has not been properly connected The input mode is not correct Confirm that the camcorder is properly connected Set the input mode to L 1 F 1 S 1 or 5 2 5 The recorder automatically rewinds the tape to the beginning The end of the tape was reached during recording The programme may not have been recorded in its entirety Next time make sure you have enough time on the tape to record the entire programme TIMER RECORDING SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1 Timer r
18. still slow motion frame by frame playback mode the picture will be distorted and there will be a loss of colour When normal playback resumes from search still slow motion or frame by frame playback the picture may jitter vertically momentarily depending on the type of TV being used Clean the video heads using a dry cleaning cassette TCL 2 when Rough poor picture appears while a tape is played back The picture is unclear or no picture appears USE CLEANING CASSETTE appears on the screen only with O S D PLAY set to ON gt pg 46 NOTE The heads get dirty in the following cases in an environment prone to extreme temperature or humidity in a dusty environment flaw dirt or mold on video tapes continuous usage for a long time PLAYBACK cont Still Picture Frame By Frame Playback 1 Pause during playback Push the JOG dial OR Press 2 Activate frame by frame playback Turn the JOG dial to the right for forward frame by frame playback or to the left for reverse frame by frame playback OR Press OR Press or gt To resume normal playback press or push the JOG dial Slow Motion During playback turn the JOG dial one click to the left for forward slow motion To play in reverse slow motion continue to turn the JOG dial to the left after selecting all the forward direction slow motion modes OR
19. 3 1 1 6 1 18 1 18 1 6 1 2 1 1 5 2 3 5 7 PAL SP LP only To resume normal playback press Index Search Your recorder automatically marks index codes at the beginning of each recording This function gives you quick access to any one of 9 index codes in either direction NOTE Before starting make sure the recorder is in the Stop mode Activate Index Search Press lt or gt 444 or BPI 14441 or gt 1 is displayed on the TV screen and search begins in the corresponding direction To access index codes 2 through 9 press lt or gt repeatedly until the correct index number is displayed Example To locate the beginning of B from the current position press 1 twice To locate the beginning of D from the current position press gt once Current position Index number When the specified index code is located playback begins automatically EN 17 Skip Search During playback press 30 SEC 1 to 4 times to skip over unwanted sections Each press initiates a 30 second period of fast motion playback Normal playback resumes automatically To resume normal playback during a Skip Search press gt Instant ReView Simply by pressing a single button the recorder power comes on rewinds and begins playback of the last timer recorded programme If you have several programmes recorded you can easily access any of them NOTE Befor
20. During still picture press and hold IM for 2 seconds then release Press IM and release again to return to still picture OR During still picture press and hold lt or gt Release to return to still picture NOTE During slow motion playback some noise may appear on the TV screen Press PR or on the remote control to eliminate the noises High Speed Turbo Search During playback turn the JOG dial quickly to the left or right OR During playback or still press BB for forward high speed search or lt for reverse high speed search NOTE For short searches press and hold or lt 44 for over 2 seconds during playback or still picture When released normal playback resumes To resume normal playback press Variable Speed Search During playback turn the JOG dial to the right for forward variable speed search or to the left for reverse variable speed search OR During playback press lt or gt The more times you press the faster the playback picture moves To decrease speed press the button for the opposite direction NOTES For speed search refer to the table below You can see smooth slow motion picture only during 1 2x slow motion playback You can hear the normal audio track only during 1 5x speed search Reverse Forward Reverse Reverse Reverse Slow Normal Forward search slow motion la search play motion pay 7 5
21. INITIAL SET AY MENU EXIT 4 Select your country Press AV to move the highlight bar pointer to your country s name 0 1 2 IMPORTANT In certain reception conditions station names may not be stored correctly and Auto Guide Program Number Set may not work properly If the Guide Program numbers are not set properly when you timer record a TV programme using the SHOWVIEW system the recorder will record a TV programme of a different station When programming the timer using the SHOWVIEW system be sure to check the desired channel is selected correctly I pg 28 SHOWVIEW Timer Programming Your video recorder memorizes all detected stations even if reception of some of them is poor You can delete those stations with an unacceptable picture pg 53 Delete A Channel NOTES Fine tuning is performed automatically during Auto Channel Set If you want to perform tuning manually refer to page 54 If you perform Auto Channel Set when the aerial cable is not connected properly SCAN COMPLETED SIGNAL appears on the TV screen in step 6 When this happens make sure of the aerial connection and press OK Auto Channel Set will take place again If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored
22. Programme title Before entering the programme title F pg 38 recording start time and station name appear instead of the programme title 4 Select programme Press AV to move the highlight bar pointer to the programme you want to watch 14 06 02 22 00 BBC 7 2727 02 01 22 00 2 15 06 02 WORLD CUP av gt GE X DELETE 1 TITLE MENU EXIT H Start playback Press OK SEARCHING appears on the TV screen Playback begins automatically after the selected programme is located NOTES f you do not want to use Programme Navigation function set PROG NAVIGATION to OFF pg 46 You cannot edit programme title or delete tape data for the cassette with the record safety tab removed and REC SAFETY is set to ON F pg 48 Programme Navigation is possible with the cassettes recorded with this recorder only e Before recording make sure the recorder clock is set correctly To record the programme information in this recorder s memory you must continue to record each programme for over the minimum recording time 8 minutes for the SP mode 15 minutes for the LP mode or 23 minutes for the EP mode Programme Navigation may not work properly depending on the tape being used The programme information is stored in this recorder s memory If the memory in this recorder should ever be damaged and the programme information lost it is i
23. S 2 B Current Day Month Year Clock Display Timer Warning Display A warning appears on the TV screen to tell you that the timer recording is to start in 5 minutes if you re not in the Timer mode at that time The warning blinks for the entire 5 minutes leading up to the start of timer recording To clear the display press X on the remote control S VHS ET Indicator S VHS ET ON S VHS ET OFF c pg 22 47 Cassette Loaded Mark EN REMOTE CONTROL START STOP o _ ri FIN DATE PR 0 prog AM 305522 O _ Cs 60D EXPRESS 7 INDEX cont TV Button gt Operating JVC TVs on page 9 TV VCR Button gt Operating JVC TVs on page 9 REVIEW Button c pg 17 Number Keys gt pg 19 28 VPS PDC Button gt pg 29 31 Q Cancel X Button gt pg 33 0000 Button gt pg 21 STOP Button c pg 30 START Button c pg 30 PROG Button gt pg 28 Programme Check Button gt pg 33 Rewind lt lt Button gt pg 15 16 Record Button c pg 19 Stop Button c pg 15 19 D MENU Button c pg 37 A v Button r pg 12 TV PR Button gt Operating JVC TVs on page 9 D STANDBY ON Button gt pg 12 AUDIO Button gt pg 18 xps TV Muting Button cx Operating JVC TVs on page 9 Display But
24. manufactured under licence from Gemstar Development Corporation EN 3 For Italy It is declared that this product brand JVC conforms to the Ministry Decree 548 of 28 Aug 95 published in the Official Gazette of the Italian Republic 301 of 28 Dec 95 The STANDBY ON button does not completely shut off mains power from the unit but switches operating current on and off b shows electrical power standby and I shows Video tapes recorded with this video recorder in the LP EP Long Play Extended Play mode cannot be played back on a single speed video recorder When the equipment is installed in a cabinet or a shelf make sure that it has sufficient space on all sides to allow for ventilation 10 cm or more on both sides on top and at the rear When discarding batteries environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly Failure to heed the following precautions may result in damage to the recorder remote control or video cassette 1 DO NOI place the recorder in an environment prone to extreme temperatures or humidity in direct sunlight in a dusty environment in an environment where strong magnetic fields are generated on a surface that is unstable or subject to vibration 2 DO NOI block the recorder s ventilation openings or holes If the ventilation openings or holes
25. names gt pg 55 appear as you press AV PR ID ZFINE 06 CH45 2 S A V CHANGE ID 4 CURSOR lt gt OK MENU EXIT 4 Switch the stations Press OK The Confirmation screen appears Repeat steps 1 4 as necessary H Close the Confirmation screen Press MENU Set Stations B Set station names other than the ones registered in your recorder Perform steps 1 and 2 of Manual Channel Set on page 52 to access the Confirmation screen and then perform steps 1 and 2 of Set Stations A above before continuing Hl Select the character for station name Press gt until the first letter of the station name begins blinking PR ID 06 45 ARD A Y A Z 0 9 4 CURSOR lt gt 0K MENU EXIT Close the Confirmation screen Press MENU NOTE The characters available for the station name ID are A Z 0 9 space maximum of 4 Fine Tuning Channels Already Stored Perform steps 1 and 2 of Manual Channel Set on page 52 to access the Confirmation screen before continuing Hl Select the channel to fine tune Press AV until the channel you want to tune begins blinking Access the Manual Channel Set screen Press OK twice The Manual Channel Set screen appears Perform tuning Press gt until begins blinking then press AV until th
26. number Pressing changes the display to the programme start time the stop time the date the tape speed then the channel position pi IMPORTANT Make sure the channel position number you wish to record is displayed if not see SHOWVIEW System Setup on page 49 and set the Guide Program number correctly If the number you entered is invalid ERROR appears on the TV screen and Err appears on the front display panel Press X and input a valid SHOWVIEW number If the GUIDE PROG SET screen appears see ATTENTION on page 29 4 Set the tape speed Press SP LP EP L LI It is not possible to select EP mode if COLOUR SYSTEM is set to CF pg 48 Set the VPS PDC mode Press VPS PDC number key 7 to select ON or OFF e If VPS PDC ON is displayed on the TV screen VPS PDC is set to ON e If VPS PDC OFF is displayed on the TV screen VPS PDC is set to OFF VPS PDC Recording on page 31 m Access the Title Edit screen Press the number key 1 TM The Title Edit screen appears You can access the Title Edit screen only when PROC 7 NAVIGATION is set to ON pg 46 S 2 SS 25 12 21 00 ARD 7 0 9 SELECT LETTERS X DELETE 14 gt 1 CURSOR lt gt 0K PROG EXIT Enter the programme title Press the number keys and gt
27. recording fits on the tape this feature may leave a slight non recorded section at the end of the tape There may be some noise and sound disturbance at the point on the tape where the recorder switches from SP to LP mode The Auto SP LP Timer feature will not work properly with any tapes longer than E 180 or with some tapes of shorter lengths f you perform timer recording with both VPS PDC and the Auto SP LP Timer activated and the programme goes beyond its originally scheduled length there may be times when the programme cannot be recorded in its entirety EN 47 The default setting is bold in the table below m DIGITAL ON OFF When this function is set to ON the Digital 3R picture system applies edge correction to the luminance signal to enhance detail NOTES Normally it is recommended to keep DIGITAL set to ON Depending on the type of tape being used picture quality may be better with DIGITAL set to OFF you use the recorder as the source player for editing be sure to set DIGITAL to OFF before starting m POWER SAVE ON OFF When this function is set to ON you can reduce the power consumption while the recorder is turned off NOTES e During Power Save mode the front display panel will be turned off the Just Clock function F pg 56 does not work the picture may be distorted mo
28. the front AUDIO S VIDEO input connectors 4 Prepare for recording Insert the recording cassette into each SR V10E and prepare the playback source device EN 27 Start recording Press on either of SR V10E When the tape remaining time reaches to 2 minutes during recording the other SR V10E successively starts recording The cassette will automatically be rewound when the recording stops Therefore recording will be continued onto cassettes loaded on two SR V10E alternately Replace the cassette after rewound if you want to continue to record onto another cassette mnm Stop recording Press on the SR V10E which is recording NOTES When recording a TV broadcast select in the same channel on both SR V10E If the playback source device has a superimpose OSD disable feature set its superimpose or display feature to OFF If you do not want to record the operational indicators displayed on the TV screen during recording set O S D PLAY and O S D REC to OFF F pg 45 46 If there is a power outage during Series Recording the recording will resume automatically when the power is restored to the recorder if the lithium battery is not exhausted It is possible to use the Mode Lock function pg 20 2 8 TIMER RECORDING With the SHOWVIEW system timer programming is greatly simplified because each TV programme has a corresponding code numb
29. using Express Timer Programming 1 Perform steps 1 12 Enter L 1 or S 1 for the channel position in step 6 2 Set the satellite receiver to the appropriate channel before the selected programme begins 3 Leave the satellite receiver s power on VPS PDC Recording Now available from some TV stations PDC Programme Delivery Control and VPS Video Programme System are service designed to assure safe accurate timer recording With this system special code signals are transmitted together with the audio video signals These code signals control your video recorder and have precedence over the advertised times you may have preset into the timer This means that your recorder will start and stop recording when the preset TV programmes actually start and end even if the broadcast time of a preset TV programme is changed NOTES e When you use Express Timer Programming set the start time VPS or PDC time exactly as advertised in the TV listing A different time than advertised will result in no recording e VPS PDC recording is also possible when a satellite receiver or a cable system is connected to the AUDIO VIDEO IN connectors on your recorder How to check if the station being received transmits a VPS PDC signal 1 Press until the channel position appears on the front display panel 2 Hold down START for about 5 seconds VPS PDC appears blinking on the TV screen
30. 5 minutes to protect the heads When returning from variable speed search to normal playback the picture is disturbed Should I be concerned about this No it is normal Noise bar appear during variable speed search What s the problem This is normal Sometimes during Index Search the video recorder can t find the programme I want to see Why not There may be index codes too close together RECORDING Q When I pause and then resume a recording the end of the recording before the pause is overlapped by the beginning of the continuation of recording Why does this happen This is normal It reduces distortion at the pause and resume points Q Can the video recorder indefinitely remain in the Record Pause mode No The video recorder goes to its Stop mode automatically after 5 minutes to protect the heads Q What happens if the tape runs out during recording The recorder automatically rewinds the tape to the beginning QUESTIONS AND ANSWERS TIMER RECORDING O and remain lit on the front display A panel Is there a problem No This is a normal condition for a timer recording in progress Can I programme the timer while I m watching a tape or a TV broadcast You won t see the picture as it is replaced by the on screen menu but the audio from the programme or tape you re viewing can be heard SPECIFICATIONS GENERAL Power
31. 9 55 WEST 03 10 ZDF 10 C24 SATI 03 7608 SKY 10 C24 SATI 04 C65 RAI 11 C23 OSF 04 10 ZDF 11 C23 OSF 05 7631 BBCf 12 C25 ESPN 05 C31 1 12 C25 ESPN 06 C32 BBC2 13 EM 06 C32 BBC2 13 E I 07 C33 3SAT 14 07 C33 3SAT 14 EM AY 4 MOVE MANUAL CH SET MENU EXIT Av 4 gt MOVE MENU EXIT Repeat steps 1 and 2 as necessary Close the Confirmation screen Press MENU 54 Set Stations A Set station names that are registered in your recorder Perform steps 1 and 2 of Manual Channel Set on page 52 to access the Confirmation screen before continuing Select the item Press AV until the item you want begins blinking SUBSIDIARY SETTINGS cont Enter the new character Press AV to cycle through the characters A Z 0 9 space and stop when the desired character is indicated then press gt to enter Enter the remaining characters the same way maximum of 4 After entering all characters press OK The Confirmation screen appears If you make a mistake press lt until the incorrect character begins blinking Then enter the correct character by pressing V Access the Manual Channel Set screen Press OK twice Select the new station Press until the station name ID begins blinking then press AV until the new station s name ID you want to store begins blinking Registered station
32. LICIA M6 M6 TVI TV INDEPENDENT MBC MBR TVN TV NORGE MCM MCM VCR VIDEO MDR MDR VERO VERONICA MOVE MOVIE VH 1 VH 1 MTV MTV VIVA VIVA MTV3 MTV3 VIV2 VIVA2 N3 NORD3 VMTV VIDEO MUSIC N TV N TV VOX VOX NBC NBC SUPER VT4 VT4 NDR3 NDR3 NED1 NED1 WDRI1 West1 NED2 NED2 WDR3 West3 NED3 NED3 YLE1 YLE1 NEWS YLE2 YLE2 NICK NICKELODEON ZDF ZDF NRK NRK ZIV ZIV Ane EO N The ID abbreviation is what is shown on screen in lieu of the station ORFI ORFI name The ID abbreviation is listed in the Confirmation screen and is displayed on the TV screen when the recorder is tuned to a different station 5 Clock Set Turn on the TV and select the video channel or AV mode dl 2 8 C5 6 r 0 Just Clock The Just Clock function provides accurate time keeping through automatic adjustments at regular intervals by reading data from a PDC signal The Just Clock option can be set ON or OFF at the Clock Set screen the default setting is OFF Press OK until the Just Clock setting begins blinking then press AV to change the setting IMPORTANT If you turn off Just Clock the accuracy of your recorder s built in clock may be reduced which could adversely effect timer recording We recommend you to keep Just Clock on In cases where the clock setting data from a PDC signal is incor
33. OWVIEW system does not timer record properly The recorder s channel positions have been set incorrectly Refer to Guide Program Number Set F pg 49 and re perform the procedure 61 SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 7 Nu and gt on the front display panel won t stop blinking The loaded cassette has had its record safety tab removed and REC SAFETY is set to ON The end of the tape was reached during Automatic Satellite Programme Recording Set REC SAFETY to OFF I pg 48 or using adhesive tape cover the hole where the tab was removed The programme may not have been recorded in its entirety Next time make sure you have enough time on the tape to record the entire programme OTHER PROBLEMS SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1 Whistling or howling is heard from the TV during camcorder recording The camcorder s microphone is too close to the TV The TV s volume is too high Position the camcorder so its microphone is away from the TV Turn the TV s volume down 2 When scanning channels some of them are skipped over Those channels have been designated to be skipped If you need the skipped channels restore them F pg 52 3 The channel cannot be changed Recording is in progress Press to pause the recording change channels then press to r
34. PUBLIKA POLSKA or OTHER EASTERN EUROPE for the country setting gt pg 12 press AV to set to 2 For other countries set to 1 Then press OK 1 B G 2 D K 4 z E ges LI Set the video channel With AV or S VIDEO Connection Press until the front display panel shows 1 or 4 Now the video channel is set to off With RF Connection Press PR or to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area Example If channel 50 is available in your area amp 7 cr HI Z lt Then set your TV to UHF channel 50 e If the two vertical white bars appear clearly on the TV screen as shown to the right go to step 4 e If the two vertical white bars do not appear clearly re set the video recorder to another vacant channel and try again NOTES f you set the video recorder to a channel which is occupied by local station or has neighbouring channels that are occupied by local stations the picture reception quality will be affected and some interference noise will appear on the TV screen Be sure to select a vacant channel which has no broadcast on neighbouring channels f you cannot obtain the two vertical white bars clearly with any channel between 22 and 69 consult your JVC dealer 4 Exit the Video Channel Set mode Press OK on the remote control
35. REC SAFETY to OFF gt pg 48 The recorder will come on automatically Turn on the TV and select the video channel or AV mode ATTENTION It is impossible to perform timer programming during recording Soe CE x E Er 1 20 3 VPS PDC WEEKLY PR STOP DATE PROG An OK TIMER RECORDING cont If you do not know the SHOWVIEW number for the programme you wish to record use the following procedure to set your recorder to timer record the programme Example To timer record the programme from 21 00 to 22 00 on 25th December on channel 1 Hl Access the SHOWVIEW screen Press PROG Access the Programme screen Press START If you re just starting out P1 appears P1 START STOP SP VPS PDC OFF DATE TV PROG EE EH PROG EXIT 1 TITLE The front display panel looks like this Enter the programme start time Press to enter the time you want recording to start Press and hold START to move in 30 minute increments or press and DATE release repeatedly to move 1 minute at a time p1 START STOP SP VPS PDC OFF TV PROG gt PROG EXIT 1 TITLE The front display panel looks like this P r LIT L tue m 4 Enter the programme sto
36. VIDEO CASSETTE RECORDER SR V10E FIRST AUTO SET UP on PAGE 12 SHOWVIEW A F SHS Super VHS ET Professional CONTENTS SAFETY FIRST 2 Safety Precautions 2 INDEX 4 INSTALLING YOUR NEW RECORDER 10 Basic Connections 10 S VIDEO Connection 11 INITIAL SETTINGS 12 Auto Set Up PLAYBACK Basic Playback Playback Features RECORDING Basic Recording Recording Features B E S T Picture System SERIES PLAYBACK AND RECORDING 24 Series Playback nte 24 Series Recording 26 TIMER RECORDING 28 SHOWVIEW Timer Programming 28 Express Timer Programming 30 24 Hour Express Timer Programming 32 Automatic Satellite Programme Recording PROGRAMME NAVIGATION 36 INavVigatiOrt teen et tede 36 EDITING 40 Edit From A Camcorder 40 Edit To Or From Another Video Recorder 41 SYSTEM CONNECTIONS 42 Connecting To A Satellite Receiver 42 Connecting Using A Stereo System SUBSIDIARY SETTINGS Mode Set SHOWVIEW System Setup TUMOR Set te
37. Z once to enter W then press D Press 7 PQRS four times to enter S then press D gt NUMBER KEY CHARACTER 114759 ABC2AAAAAA DEF3EEEE GHI4111f JKL5 MNO6bOOOOOGN PQRS7 TUV8UUUU WXYZ9 0 NOTES If you make a mistake press gt to select the character then enter the correct character e If you want to delete a character press lt 1 gt to select the character then press X EN 29 Delete Tape Data before continuing Perform steps 1 to 3 of Navigation Playback on page 37 Hl Delete the tape data Press X for more than 3 second All the programme data on the tape are deleted then normal screen appears It is impossible to delete each programme information 14 06 02 22 00 BBC ccs PR 7 5727 02 01 22 00 BBC2 15 06 02 WORLD CUP Av 1 TITLE X DELETE MENU EXIT NOTE When you delete the tape data only the tape information is deleted from the recorder s memory The actual recording on the tape is not erased 40 in Edit From A Camcorder If the camcorder has no S VIDEO output connector Recorder Camcorder Player VIDEO OUT Video ca
38. ance on top of the recorder as it may cause picture disturbance 4 INDEX FRONT VIEW Cer VIDEO MONO L AUDIO R STANDBY ON v Button gt pg 12 Q Infrared Beam Receiving Window Q Cassette Loading Slot REC LINK Button gt pg 35 24H EXPRESS Button c pg 32 Record Button c pg 19 S VIDEO VIDEO AUDIO Input Connectors Pause Button c pg 16 t pg 40 Play gt Button gt pg 15 Stop Eject I 4 Button gt pg 15 19 Advanced JOG Dial gt pg 15 32 S VHS ET Button c pg 22 Front Display Panel gt pg 6 Connector cover 0 1 Attach the provided connector cover when you do not use the front panel connectors To attach it insert the cover s left tab to the recorder s front panel connector part then push in the cover s right side To remove it press the cover s left side REAR VIEW EN Mains Power Cord gt pg 10 5 VIDEO OUT Connector pg 11 24 26 41 42 5 VIDEO IN Connector gt pg 24 26 41 42 Lithium battery compartment gt See below REMOTE OUT Connector gt pg 24 26 AUDIO VIDEO OUT Connectors pg 10 24 26 41 42 43 Installing Removing the lithium battery OUT IN S 1 S VIDEO AUDIO VIDEO IN Connectors pg 24 26
39. are blocked by a newspaper or cloth etc the heat may not be able to get out 3 DO NOI place heavy objects on the recorder or remote control 4 DO NOI place anything which might spill on top of the recorder or remote control If water or liquid is allowed to enter this equipment fire or electric shock may be caused 5 DO NOT expose the apparatus to dripping or splashing 6 DO NOT use this equipment in a bathroom or places with water Also DO NOT place any containers filled with water or liquids such as cosmetics or medicines flower vases potted plants cups etc on top of this unit 7 DO NOI place any naked flame sources such as lighted candles on the apparatus 8 AVOID violent shocks to the recorder during transport MOISTURE CONDENSATION Moisture in the air will condense on the recorder when you move it from a cold place to a warm place or under extremely humid conditions just as water droplets form in the surface of a glass filled with cold liquid Moisture condensation on the head drum will cause damage to the tape In conditions where condensation may occur keep the recorder turned on for a few hours to let the moisture dry ATTENTION To mobile phone users Using a mobile phone in the vicinity of the recorder may cause picture vibration on the TV screen or change the screen to a blue back display On placing the recorder Some TVs or other appliances generates strong magnetic fields Do not place such appli
40. ble Audio cable AUDIO OUT If the camcorder has an S VIDEO output connector Recorder Camcorder Player Audio cable S Video cable S VIDEO OUT AUD IO OUT EDITING You can use a camcorder as the source player and your recorder as the recording deck Hl Make connections 1 If the camcorder has no S VIDEO output connector connect the camcorder s AUDIO OUT and VIDEO OUT connectors to the recorder s front panel AUDIO and VIDEO input connectors 2 If the camcorder has an S VIDEO output connector connect the camcorder s AUDIO OUT S VIDEO OUT connectors to the recorder s front panel AUDIO and S VIDEO input connectors When using a monaural camcorder connect its AUDIO OUT connector to the AUDIO L input connector on your recorder 2 Set the recorder s input mode Press AUX number key 0 and or PR to select F 1 for the AUDIO and VIDEO input connectors or S 2 for the AUDIO and S VIDEO input connectors depending on the connectors being used Set the edit mode See PICTURE CONTROL on page 45 4 Start the camcorder Engage the Play mode of the camcorder Start the recorder Engage the Record mode of the recorder NOTES All necessar
41. by Auto Set Up the TV system setting for those channels may be incorrect Select the appropriate TV system for those channels C pg 53 INFORMATION Perform Auto Channel Set Press OK The Auto Set screen appears 2 AUTO SET and remains on screen while lt y the recorder searches for PLEASE WAIT lt receivable stations As Auto Channel Set ges progresses the M mark on the TV screen moves from MENU EXIT left to right Wait until the TV screen as shown in step 6 appears Beginning End nm View the Confirmation screen After SCAN COMPLETED is PR CH ID PR CH 1 displayed on the TV screen for US i MIU MES about 5 seconds the 03 10 10 C24 Confirmation screen looking MES 11 08 like the one to the right appears The stations your recorder located appear on a Confirmation screen channel positions PR channels CH and station names ID cF pg 55 The blueback screen and the programme currently being broadcast by the blinking station appear alternately for 8 seconds each To view the next page use the AV button on the remote control The stations located in the selected country appear at the top of the list The Guide Program numbers will also be set automatically during Auto Channel Set 06 C32 13 07 C33 14 4 4 gt ae EDIT X DELETE MENU EXIT Return to the normal screen Press MENU Using the Confirmatio
42. c tracking control During playback you can override this and adjust the tracking manually by pressing the PR buttons 1 Override automatic tracking During playback press on the remote control 2 Adjust the tracking manually Press PR or on the remote control Press HM again to return to automatic tracking NOTE When a new tape is inserted the recorder enters the automatic tracking mode automatically Soundtrack Selection Your recorder is capable of recording three soundtracks HI FI L HI FI R and NORM and will play back the one you select During Playback Pressing AUDIO changes the soundtrack as follows TRACK USE On Screen Display HI FI oe Ll ae For Hi Fi stereo tapes HI FI wi Lie For main audio of Bilingual tapes HI FI For sub audio of Bilingual tapes NORM For audio dubbed tapes HI FI NORM For audio dubbed tapes NOTES e HI FI 0 9 R should normally be selected In this mode Hi Fi stereo tapes are played back in stereo and the normal audio track is played back automatically for tapes with only normal audio For instructions on recording stereo and bilingual programmes refer to page 22 e O S D PLAY must be set to ON or the on screen displays will not appear gt pg 46 RECORDING Basic Recording Turn on the TV and select the video channel or AV mode
43. can check the current setting S VHS ET ON or S VHS ET OFF If S VHS ET ON appears on the TV screen press S VHS ET again in about 5 seconds to set it to OFF The VHS recording mode is automatically selected regardless of the S VHS mode setting To record in VHS on an S VHS cassette Insert a cassette marked S VHS The S VHS indicator lights up on the front display panel Then set S VHS to OFF The S VHS indicator goes off The VHS recording mode is selected NOTE When playing back a tape that has been recorded in S VHS or S VHS ET the S VHS indicator lights up on the front display panel regardless of the S VHS mode setting 48 SUBSIDIARY SETTINGS cont The default setting is bold in the table below m COLOUR SYSTEM AUTO PAL NTSC MESECAM You can play back PAL NTSC and MESECAM tapes or record PAL and SECAM signals on this recorder Select the appropriate colour system SECAM signals will be recorded as MESECAM on this recorder MESECAM is the designation for tapes with SECAM signals that have been recorded on a MESECAM compatible PAL video cassette recorder AUTO Normally set to this mode The appropriate colour system is selected automatically depending on the playback or recording signals You can select AUTO only when OTHER EASTERN EUROPE is selected for the country setting C pg 12 In this case the default setting is AUTO If
44. corder s power once then turn the recorder s power back on again The Country Set display appears on the TV screen perform Auto Set Up on page 12 again IMPORTANT To check if the Guide Program numbers have been set correctly perform the SHOWVIEW Timer Programming gt pg 28 In certain reception conditions station names may not be stored correctly and auto Guide Program Number Set may not work properly If the Guide Program numbers are not set properly when you timer record a TV programme using the SHOWVIEW system the recorder will record a TV programme of a different station When programming the timer using the SHOWVIEW system be sure to check the desired channel is selected correctly 05 pg 28 SHOWVIEW Timer Programming Your video recorder memorizes all detected stations even if reception of some of them is poor You can delete those stations with an unacceptable picture I pg 53 Delete A Channel INFORMATION Just Clock Your recorder is equipped with the Just Clock function which provides accurate time keeping through automatic adjustments at regular intervals by reading data from a PDC signal If you want to take advantage of this function simply set it to ON F pg 56 Just Clock Last Function Memory When the power plug is removed from the recorder or when the power failure occurs your settings for the following functions are kept in memory if the lit
45. corder s front display panel during automatic tracking pg 23 4 Stop playback Press on the remote control on the recorder s front panel Then press to remove the cassette Usable cassettes Compact VHS camcorder recordings can be played on this video recorder Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full sized VHS cassette This video recorder can record on regular VHS and Super VHS cassettes While only VHS signals can be recorded on regular VHS cassettes both VHS and Super VHS signals can be recorded and played back using Super VHS cassettes By using the S VHS ET function it is possible to record and play back with S VHS picture quality on VHS cassettes with this recorder Playback Resume Function If there is a power outage during normal playback Repeat Playback c7 pg 18 or Series Playback I pg 24 the playback will resume automatically when the power is restored to the recorder if the lithium battery is not exhausted Playback Features ATTENTION Picture may not appear during high speed search with an LP EP recorded tape Noise may appear or the picture may appear distorted with an EP recorded tape during still slow motion frame by frame playback or variable speed search In the high speed search
46. ded with this recorder only e Before recording make sure the recorder s clock is set correctly To record the programme information in this recorder s memory you must continue to record each programme for over the minimum recording time 8 minutes for the SP mode 15 minutes for the LP mode or 23 minutes for the EP mode Programme Navigation may not work properly depending on the tape being used The programme information is stored in this recorder s memory If the memory in this recorder should ever be damaged and the programme information lost it is impossible to restore that information m AUTO SP LP TIMER ON OFF When this function is set to ON the recorder automatically switches to LP mode to allow complete recording if there is not enough tape to record the entire programme while timer recording in SP mode For Example Recording a programme of 210 minutes in length onto a 180 minute tape Approximately 150 minutes Approximately 60 minutes SP mode LP mode Total 210 minutes Make sure you set this function to ON before the timer recording starts NOTES If you have programmed the recorder to timer record 2 or more programmes the second programme and those thereafter may not fit on the tape if you set AUTO SP LP TIMER to ON In this case make sure the mode is not engaged then set the tape speed manually during timer programming In order to ensure that the
47. e Confirmation screen before continuing Hl Select the item Press AV until the item you want to delete begins blinking Delete channel Press X The item directly beneath the cancelled one moves up one line Repeat steps 1 and 2 as necessary Close the Confirmation screen Press MENU INFORMATION If you live in Eastern Europe TV SYSTEM setting appears on the Manual Channel Set screen When you can see the picture but can hear no audio select appropriate TV system D K or B G Normally TV programmes are broadcasted as follows For Eastern Europe D K For Western Europe B G 1 Select a country in Eastern Europe in step 4 on page 50 2 Press gt until the TV system D K or B G blinking on the Manual Channel Set screen in step 4 on page 52 3 Press AV to select appropriate TV System D K or B G i Select the item Press AV lt gt until the item you want to move begins blinking Then press OK and the station name ID and its channel CH number begin blinking 2 Select the new position Press AV to move the station to the new channel position then press OK Example If you moved the station in position 4 to position 2 the stations originally in positions 2 and 3 each move down one space PR CH ID PR CH ID PR CH ID PR CH ID 01 25 ARD 08 C26 ESP 01s 25 2 08 C26 02 C08 SKY1 09 55 WEST 02 C65 0
48. e picture is its clearest Then press OK The Confirmation screen appears Repeat steps 1 3 as necessary 4 Close the Confirmation screen Press MENU TV Station And ID List EN 55 ID STATION NAME ID STATION NAME 1000 TV1000 ORF2 ORF2 3SAT 3SAT ORF3 ORF3 9LIV 9LIVE OWL3 OWL3 ADLT ADULT PREM PREMIERE ANT3 ANTENA3 PRO7 7 ARD ARD RAI2 RAI2 B1 BERLIN1 RAI3 RAI3 BBC BBC GROUP RETA RETEA BBC1 BBC1 21 TELE21 BBC2 BBC2 RTBF RTBF1 or 2 BR3 RTL RTL C CANAL PLUS RTL2 RTL2 PORTUGUSES RTL4 RTL4 CAN5 CANALE5 RTL5 RTL5 CANV KETNET CANVAS RTP RTP CH4 CHANNEL4 S4 SCHWEIZ4 CH5 CHANNEL5 SAT1 SAT1 CHLD CHILD SBS SBS CINE CINEMA SF1 SF1 CLUB TELECLUB SF2 SF2 CMT CMT SHOW SHOW CNN CNN SIC SOCIEDADE CSUR ANDALUCIA SKY SKY CHANNEL DISC DISCOVERY SKYN SKY NEWS DR DRTV SPRT SPORT DR2 DR2 SRTL SUPER RTL DRS DRS STAR STAR TV DSF DSF SVT1 SVT1 ETB1 ETB1 SVT2 SVT2 ETB2 ETB2 SWR SUEDWEST3 EURO EURONEWS TEE TCC EUSP EUROSPORTS TELE TELE FEMM FEMMAN TEL5 TELE5 FILM FILM TF1 TF1 FNET FILMNET TMC TELEMONTECARLO FR2 France2 TNT TNT INT FR3 France3 TRT TRT INT GALA GALAVISION TSI TSI HR3 HESSEN3 TSR TSR INFO INFO KANAL TV1 BRTN TV1 ITA1 ITALIA1 TV2 TV2 ITA7 ITALIA7 TV3 TV3 ITV ITV1 TV4 TV4 JSTV JSTV TV5 TV5 KA2 KA2 TV6 TV6 KAB1 KABEL1 TVE1 TVE1 KAN2 KANAL2 TVE2 TVE2 LOCA LOCAL TVG TV GA
49. e starting make sure that the recorder is off and that the Timer mode is disengaged Adivate Instant ReView Press REVIEW The recorder power comes on and the recorder searches for the index code indicating the start of the last timer recorded programme Once it s found playback begins automatically The front display panel tells you how many programmes have been timer recorded If you have for example 3 programmes the Instant REVIEW indicator Ca and 3 blink To watch the first of the 3 programmes press REVIEW three times The recorder searches and begins playback automatically You can access a programme as far as 9 index codes away from the current tape position The number of recorded programmes will not be displayed on the front display panel after Auto Satellite Programme Recording pg 35 Mode Lock To prohibit any operations during playback Press and hold OK on the remote control for more than 5 seconds gt and 4 light up on the front display panel No buttons will function and playback will not be interrupted until the recording end unrecorded portion or tape end is reached gt pg 48 To cancel Mode Lock press and hold OK again for more than 5 seconds When is pressed to set Mode Lock the on screen display appears and the time counter remains on the TV screen If the time counter is not necessary set O S D PLAY and O S D REC to OFF gt pg 45
50. ecorder produce monochrome pictures when played back with this recorder 4 This recorder cannot be used for the SECAM L standard Use a SECAM L recorder to record SECAM L signals IMPORTANT Please read the various precautions on pages 2 and 3 before installing or operating the recorder It should be noted that it may be unlawful to re record pre recorded tapes records or discs without the consent of the owner of copyright in the sound or video recording broadcast or cable programme and in any literary dramatic musical or artistic work embodied therein Caution on Replaceable lithium battery The battery used in this device may present a fire or chemical burn hazard if mistreated Do not recharge disassemble heat above 100 or incinerate Replace battery with Panasonic Matsushita Electric Sanyo Sony or Maxell CR2025 Danger of explosion or Risk of fire if the battery is incorrectly replaced W Dispose of used battery promptly W Keep away from children W Do not disassemble and do not dispose of in fire SVIS SHOWVIEW Cassettes marked S VHS and VHS can be used with this video cassette recorder However S VHS recordings are possible only with cassettes marked S VHS By using the S VHS ET function it is possible to record and play back with S VHS picture quality on VHS cassettes with this recorder SHOWVIEW is a registered trademark of Gemstar Development Corporation The SHOWVIEW system is
51. ecording won t work The clock and or the timer have been set incorrectly The timer is not engaged Re perform the clock and or timer settings Press and confirm that O is displayed on the front display panel 2 Timer programming is not possible Timer recording is in progress Timer programming can t be performed while a timer recording is in progress Wait until it finishes 3 on the front display panel won t stop blinking The timer is engaged but there s no cassette loaded Load a cassette with the record safety tab intact If the tab has been removed set REC SAFETY to OFF I pg 48 4 and on the front display panel won t stop blinking The loaded cassette has had its record safety tab removed and REC SAFETY is set to ON The end of the tape was reached during timer recording Set REC SAFETY to OFF pg 48 or using adhesive tape cover the hole where the tab was removed The programme may not have been recorded in its entirety Next time make sure you have enough time on the tape to record the entire programme 5 blinks for 10 seconds and the Timer mode is disengaged has been pressed when there are no programs in memory or the timer record information has been programmed incorrectly Check the programmed data and re program as necessary then press again 6 The SH
52. er which your recorder is able to recognize Hl Access the SHOWVIEW screen SHOWVIEW NO e Programming I Before performing the SHOWVIEW Timer 2 Programming Make sure that the recorder s built in clock is set properly Insert a cassette with the safety tab in place If the tab has been removed set REC SAFETY to OFF pg 48 The recorder will come on automatically PROG EXIT Turn on the TV and select the video channel AV mode ATTENTION The front display panel looks like this It is impossible to perform timer programming during DENM recording 2 Enter the SHOWVIEW number Press the number keys to enter the SHOWVIEW number of a programme you wish to record SHOWVIEW NO 123456 C If you make a mistake press X Ca and input the correct number 0 91 gt C x C CO X DELETE _ 2 GY PROG EXIT DAILY T The SHOWVIEW number you enter appears the front display 0 9 panel with only 4 digit number WEEKLY rrin x 3D 10 STOP Access the SHOWVIEW Program screen Press OK and the SHOWVIEW E Program screen appears if SHOWVIEW NO 123456789 PROG you re just starting out P1 A EE HS appears SP VPS PDC OFF DATE TV PROG 25 12 1 ARD OK GE OK 1 TITLE The front display panel shows the programme
53. esume recording 4 Channel settings that were made manually seem to have changed or disappeared After the manual settings were made Auto Channel Set was performed Perform manual setting again 5 No channels are stored in the recorder s memory The TV aerial cable was not connected to the recorder when Auto Set Up was performed Turn off the recorder once and connect the TV aerial cable to the recorder properly then turn on the recorder again Then perform Auto Set Up again gt pg 12 6 Buttons and controls do not function at all Mode Lock is activated Press and hold OK for more than 5 seconds to cancel Mode Lock F pg 17 20 ATTENTION This recorder contains microcomputers External electronic noise or interference could cause malfunctioning In such cases switch the recorder off and unplug the mains power cord Then plug it in again and turn the recorder on Take out the cassette After checking the cassette operate the unit as usual 62 PLAYBACK Q A Q What happens if the end of the tape is reached during playback or search The tape is automatically rewound to the beginning During search slow still and frame by frame playback can t hear any audio What s the problem This is normal Q Can the video recorder indefinitely remain in gt 0P the still mode No It stops automatically after
54. h RF After the button on the recorder or remote control is pressed for the first time to power on the recorder by simply selecting your country the Auto Set Up function sets the tuner channels clock and Guide Program numbers automatically f you live in Hungary MAGYARORSZAG Czech Republic CESK REPUBLIKA Poland POLSKA or other countries in Eastern Europe OTHER EASTERN EUROPE set the clock manually ila 4 C8 6 Kr connection CF pg 10 Hl Turn on the recorder Press the recorder or remote control The Country Set display appears on the TV screen OTE If you have connected your TV to a REPUBLIKA 1 1 DANMARK the recorder with RF connection DEUTSCHLAND and the on screen display ESPANA appearing on UHF channel 36 looks distorted perform Video MAGYARORSZAG NEXT PAGE Av MENU EXIT Channel Set on page 58 Select your country Press AV to move the highlight bar pointer to your DANMARK country s name Example DEUTSCHLAND is ESPANA selected randa MAGYARORSZ G NEXT PAGE AY MENU EXIT NOTES If you have selected MAGYARORSZ G ESK REPUBLIKA POLSKA or OTHER EASTERN EUROPE press OK The Clock Set screen appears Set the clock manually pg 56 then go to step 3 If you have selected any ot
55. he lower programme number will be recorded and the other one will not be recorded correctly Even if a power failure occurs the recorder keeps your timer programmes if the lithium battery is not exhausted TIMER RECORDING cont You can programme a timer recording that starts within 24 hours using the JOG dial on the recorder Hl Enter the programme mode Press 24H EXPRESS on the recorder The start time indicator gt starts blinking on the front display panel _ LIE 10 2 Set the programme start stop time and channel Turn the JOG dial to the left or right to set the time you want recording to start One click stop of the JOG dial changes the time 5 minute intervals NS as EREIN LILI LI Push the JOG dial The stop time indicator starts blinking on the front display panel Turn the JOG dial to the left or right to set the time you want recording to stop x Hn nn LILI Push the JOG dial Turn the JOG dial to the left or right to select the channel you wish to record 2 l You cancel the setting at any time by pressing and holding the JOG dial for more than 3 seconds or pressing X on the remote control Repeat the step 2 To set the tape speed press SP LP EP Z The current setting for the tape speed appears on the display panel for about 5 seconds Press SP LP EP again to change the se
56. he recorder will not perform Auto Set Up again You only need to set the clock I pg 56 If you have moved to a different area perform each setting as required Video channel setting for RF connection users gt pg 58 Tuner setting I pg 50 Clock setting I pg 56 If a new station starts broadcasting in your area perform tuner setting C pg 50 and if necessary video channel setting pg 58 NOTES e In the area where no TV station transmits a PDC Programme Delivery Control signal the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set e If there is a power cut or if you press or MENU while Auto Set Up is in progress Auto Set Up will be interrupted be sure to turn off the recorder power once and try again from step 1 Auto Clock Set may not function properly depending on the reception condition If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up the TV system setting for those channels may be incorrect Select the appropriate TV system for those channels Cx pg 53 INFORMATION 14 INITIAL SETTINGS cont Results of Auto Set Up appear on the front display panel If both Auto Channel Set and Auto Clock Set have been performed successfully the correct current time is displayed Turn on the TV and select its video channel or AV mode then make sure that all necessary
57. her country name go to step 3 Perform Auto Set Up Press OK Auto blinks on the front display panel do NOT press any button on the recorder or remote control until the front display panel shows either the display as illustrated in step 4 or as illustrated on page 14 If you are using the on screen display the AUTO SET screen will appear As Auto Set Up progresses the mark on the TV screen moves from left to right AUTO SET 2 PLEASE WAIT MENU EXIT Beginning End 4 Confirm Set video channel With RF connection The video channel that is 7 rt shown on the display panel is 1 your video channel Press OK 7 S If you have selected x MAGYARORSZAG CESK 7 99 7 REPUBLIKA POLSKA 1 OTHER EASTERN EUROPE GS step 2 on page 12 2 appears instead of 1 To view picture signals from the recorder set your TV to the video channel With AV or S VIDEO connection 2 Press PR until the display 1 zt panel shows 1 or 7 2 Now the video channel is set to off Then press OK To view picture signals from the recorder set your TV to its AV mode 13 ATTENTION Once you have performed Auto Set Up even if the recorder s memory backup has expired all the stored stations and their Guide Program numbers remain in the recorder s memory and t
58. hium battery is not exhausted These settings will resume when the recorder is turned on again Input selection channel or auxiliary input L 1 F 1 S 1 or S 2 Country setting I pg 12 Recording tape speed pg 19 Mode settings F pg 44 48 PLAYBACK Basic Playback Turn on the TV and select the video channel or AV mode m REVIEW X00 8K 2 4 C5 e 1 MM EN 15 Hl Load a cassette Make sure the window side is up the rear label side is facing you and the arrow on the front of the cassette is pointed toward the recorder Do not apply too much pressure when inserting The recorder will come on automatically If the record safety tab has been removed and REC SAFETY is set to ON F pg 48 playback begins automatically If the record safety tab is intact or if the record safety tab is removed and REC SAFETY is set to OFF I pg 48 the recorder checks the tape information for Programme Navigation For details refer to Navigation C pg 36 2 Find the programme start point If the tape is advanced past the start point press 4 or turn the JOG dial to the left To go forward press gt or turn the JOG dial to the right Start playback Press bESt appears blinking in the re
59. iary channel L 1 select L 1 for the channel position Repeat steps 4 and 5 as necessary Av MENU EXIT Example If ZDF is received on channel position 2 m Return to the normal screen Press MENU Guide Program Number Guide Program GUIDE PROG number refers to the assigned TV station numbers according to broadcast area for the SHOWVIEW timer recording The Guide Program numbers can be found in most TV listings 50 SUBSIDIARY SETTINGS cont Tu n e r Set steps only if Auto Channel Set has not been set correctly by Auto Set Up pg 12 Turn on the TV and select the video channel or you have moved to a different area or if a new station AV mode starts broadcasting in your area Your recorder needs to memorize all necessary stations in channel positions in order to record TV programmes Auto Channel Set automatically assigns all receivable stations in your area to call them up by using the PR buttons without going through any vacant channels Auto Channel Set Hl Turn on the recorder Press O I F Access the Main Menu screen Press MENU Access the Auto Channel Set screen 0 o o Oo CO Press AV to move the MAIN MENU highlight bar pointer to AUTO CH SET then press Oa SE E NAVIGATION OK or b MANUAL CH SET
60. ing it is not possible to set different tape speeds for each programme Depending on the type of satellite receiver the recorder may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme If you engage the Automatic Satellite Programme Recording mode when the satellite receiver s power is on the recorder will not start Automatic Satellite Programme Recording even though the X indicator blinks When the satellite receiver shuts off once and is turned back on again the recorder starts recording You can also record a programme from your cable system in the same way if the system has a timer The B E S T system t pg 23 does not work while Automatic Satellite Programme Recording is in progress e Just Clock gt pg 56 does not work when the Automatic Satellite Programme Recording mode is engaged When the Automatic Satellite Programme Recording mode is engaged or the recorder s power is turned off after Automatic Satellite Programme Recording is finished the recorder will not enter the Timer mode even though AUTO TIMER is set to ON gt pg 45 36 EN PROGRAMME NAVIGATION Navigation When you record a TV programme with this recorder the recorder automatically stores in its memory the recording date start time and station name You can store these information for up to 8 programmes on one cassette At maximum information for 10
61. is set to ON I pg 45 MARK blinks on the screen while an index code is being marked B E S T takes place at the beginning of both the first SP and the first LP or EP recording after inserting the cassette pg 23 Pause Resume recording Press Press B to resume recording You can select channel during the Record Pause mode nm Stop recording Press on the remote control or 4 on the recorder Then press to remove the cassette ATTENTION e When O S D REC is set to ON F pg 45 the operational indicators displayed on the TV screen will be recorded Set O S D REC to OFF if you do not want to record these indicators You cannot access the Main Menu screen during recording 201 Recording Features 0000 RECORDING cont Record One Programme While Watching Another Once recording is in progress all you need to do is to set the channel controls on the TV for the station you wish to view The programme selected with the TV s channel controls appears on the TV screen while the one selected with the recorder s PR buttons is recorded on the tape Mode Lock To prohibit any operations during recording Press and hold OK on the remote control for more than 5 seconds gt
62. king bESt appears blinking on the recorder s front display panel NOTES When watching a tape recorded with B E S T set to ON it is recommended that you leave B E S T on during playback as well When watching a rental tape or one recorded on another video recorder or when using this recorder as the player for editing set B E S T to your preference F pg 45 bESt only appears at the beginning of automatic tracking Even though it doesn t appear after that the B E S T function is operative EN 22 Recording The recorder assesses the quality of the tape once you initiate recording DURING B E S T LL LIL JL B E S T COMPLETE N LI e LIL JIL e The recorder spends Approximately 7 seconds assessing the condition of the tape then begins recording NOTES e The B E S T system works for both SP and LP or EP modes only after a tape has been inserted and the Record mode is first initiated It does not work during recording e The B E S T system does not work while Automatic Satellite Programme Recording is in progress F pg 35 e In the case of timer recordings the B E S T system works before recording is initiated Once the cassette is ejected the B E S T data is cancelled The next time the cassette is used for recording B E S T is re performed ATTENTION Since the B E S T system works before recording actually starts there is a dela
63. king Repeat the same procedure to set the date and year When you set the time press and hold AV to change the time by 30 minutes When you set the date press and hold AV to change the date by 15 days m Set Just Clock The default setting is OFF Set as desired by pressing AV then press OK or P For the Just clock function refer to Just Clock on page 56 If you set to OFF you can disregard the next step as you won t be able to receive regular clock adjustments Set the source channel position for clock data The recorder is preset to receive clock setting and adjustment data from channel position 1 Press AV to set the channel position to the number representing the station transmitting clock setting data then press OK or Start the clock operation Press MENU NOTES e Just Clock when set to ON adjusts the recorder s built in clock every hour except for 23 00 0 00 1 00 and 2 00 Just Clock is not effective when the recorder s power is on the recorder is in the Timer mode difference of more than 3 minutes exists between the built in clock s time and the actual time the recorder is in the Automatic Satellite Programme Recording mode gt pg 35 the recorder is the Power Save mode t pg 47 e If Just Clock is set to ON the recorder clock is automatically adjusted at the start end of Summer Time e Just Clock may not function properl
64. layback 16 Super VHS ET S VHS ET 22 47 41 47 T Tape Position Indicator eee 7 Tape Remaining Time eee 21 TIMER RECORDING He 28 Timer Warning Display eee 7 Tuner ER ARIES RUNE 50 TV Station And ID List ie 55 V Variable Speed Search 17 Vid o Channel Set 5 ttt rennes 58 VIDEO STABILIZER 1 dinae teet 47 VPS PDC R cording 22 2 piii 31 When programmes overlap each other 34 24 Hour Express Timer Programming 32 65 66 N EN 67 VICTOR COMPANY OF JAPAN LIMITED COPYRIGHT 2002 VICTOR COMPANY OF JAPAN LTD E Printed in Malaysia 0902MNV k ID PJ J0LA HS
65. layback stops and the cassette will be automatically rewound TAPE END REC END Playback stops at the end of tape Playback stops at the end of the recording DAY TIME INSERT When this function is set to ON you can record Month Day Year and clock time ON display with your picture OFF NOTE To use this function be sure to set O S D REC to ON F pg 45 Only Month Day Year and clock time displays appear REC SAFETY Usually you can only record onto a cassette with its record safety tab intact When the ON this function is set to OFF recording can be done onto a cassette whose record safety OFF tab is removed NOTE When REC SAFETY is set to OFF playback does not start automatically when you insert a cassette with its record safety tab removed pg 15 DAILY T RECORD NORM AUTO REW When you set daily timer recording you can use one cassette repeatedly If you select AUTO REW the recorder rewinds tape each time after timer recording and the timer mode is engaged If you select NORM the recorder turns off after timer recording 49 SHOWVIEW System Setup IMPORTANT Normally Auto Set Up pg 12 or Auto Channel Set pg 50 sets the Guide Program numbers automatically You need to set the Guide Program numbers manually only in the following cases When timer programming with the SHOWVIEW system the channel position where the station you wish to record is
66. le Audio video cable Infrared remote control unit R6 battery x 2 Lithium battery CR2025 BNC RCA adapter x 2 Specifications shown are for SP mode unless otherwise specified E amp O E Design and specifications subject to change without notice 64 en Auto Channel Set reete RR 50 Alito Set Up eec 12 AUTO SPSEEP TIMER Er tr RR eR een een 46 AUTO TIMER 3s 52 22 tii i ri erg tet 45 Automatic Satellite Programme Recording 35 B B E S T Picture System 23 45 Change Station Channel Position 53 Check cancel and change programmes 33 Clock Set eere ten 56 COLOUR SYSTEM e 48 Connecting To A Satellite Receiver 42 D DAILY T RECORD nee ent tnn 48 DAYTIME INSERT en 48 Delete A Channel n 53 DIGITAL BR oret 47 DIGITAL TBC NR 45 E EDITING 1er t e i ete HE RS 40 Elapsed Recording Time Indication 21 Express Timer Programming 30 F Fine Tuning Channels Already Stored 54 G Guide Program Number 29 49 H High Speed Turbo Search 16 1 Search iuit te tet ete rit ets 17 Installing Removing the lithium battery 5 Instant REVIEW e t
67. m VHS to S VHS S VHS to VHS or from S VHS to S VHS From VHS to S VHS Record VHS playback signals in the S VHS mode Although the picture quality is inherently limited by that of the original the edited tape has better picture quality than those made by VHS to VHS editing From S VHS to VHS Because the picture quality of the source material is very high the edited tape has better picture quality than those made by VHS to VHS editing From S VHS to S VHS All signals will be transferred with minimum degradation en 41 You can use your recorder as the source player or as the recording deck Make connections When using your recorder as the source player connect its AUDIO VIDEO OUT or AUDIO S VIDEO OUT connectors to the audio video or audio S video nput connectors on another recorder When using your recorder as the recording deck connect its AUDIO VIDEO IN or AUDIO S VIDEO IN connectors to the audio video or audio S video output connectors on another recorder Set the input mode of recording deck With this video recorder press AUX number key 0 and or PR to select L 1 for the AUDIO VIDEO IN connectors or S 1 for the AUDIO S VIDEO IN connectors depending on the connector being used When using another recorder as the recording deck refer to its instruction manual Set the edit mode See PICTURE CONTROL on page 45 4 Start the source player
68. mentarily when you turn on off the recorder Power Save does not work when the recorder is in the Timer mode the recorder s power is turned off after timer recording the Automatic Satellite Programme Recording mode is engaged I pg 35 m VIDEO STABILIZER When this function is set to ON you can automatically correct vertical vibration in ON the picture when playing back unstable recordings made on another recorder OFF NOTES e When you finish viewing a tape be sure to set this function to OFF Regardless of the setting this function has no effect during recording and during special effects playback The on screen display may jitter vertically when this function is set to ON To watch recordings with close caption set this function to OFF e Video Stabilizer and Digital TBC NR cannot be used at the same time If you activate Digital TBC NR when VIDEO STABILIZER is set to ON Video Stabilizer will be automatically turned m S VHS Your recorder can record in S VHS Super VHS S VHS ET or VHS xe record in S VHS Set S VHS to ON Then insert a cassette marked S VHS The S VHS indicator lights up on the front display panel The S VHS recording mode is selected To record in S VHS ET on a VHS cassette See Super VHS ET S VHS ET on page 22 To record in VHS Insert a cassette marked VHS Press S VHS ET on the recorder You
69. mpossible to restore that information 38 EN MENU PROGRAMME NAVIGATION cont Edit Programme Title You can edit the programme titles as you like Perform steps 1 to 3 of Navigation Playback on page 37 before continuing Select the programme Press AV to move the 14 06 02 22 00 highlight bar pointer to the e PH T 27 02 01 22 00 BBC2 programme you want to edit 75 06 02 WORLD Av 1 TITLE X DELETE MENU EXIT 2 Access the Title Edit screen Press the number key 1 The Title Edit screen appears P3 2 27 02 22 00 2 M 0 9 SELECT LETTERS DELETE 0 GF OK MENU EXIT Enter the programme title Press the number keys and gt to enter characters then press OK For details refer to Entering Character on page 39 4 Return to the normal screen Press MENU Entering Character Press the appropriate number key then press to enter each character Refer to the example below oe Enter JVC NEWS Press 5 JKL once to enter J then press gt Press 8 TUV three times to enter V then press D Press 2 ABC three times to enter C then press gt Press 0 twice to enter space then press D Press 6 MNO twice to enter then press D Press DEF twice to enter then press D Press 9 WXY
70. n Notice some recorders are not compatible with the S VHS ET function You can activate the S VHS ET function only before you start recording on a VHS cassette Before recording make sure that B E S T is set to pg 45 Engage the S VHS ET mode Press S VHS ET on the recorder You can check the current setting S VHS ET ON or S VHS ET OFF If S VHS ET OFF appears on the TV screen press S VHS ET again in about 5 seconds to set it to ON The S VHS indicator lights up on the front display panel NOTES You cannot activate the S VHS ET function While recording is in progress While timer recording I pg 28 30 32 is in progress While B E S T gt pg 23 is in progress e The S VHS ET function does not work With S VHS cassettes With recordings in LP EP mode To keep the highest quality recording and playback pictures over a long period of time S VHS recording on S VHS cassettes is recommended Use of high grade tapes is recommended for S VHS ET recordings On some tapes picture quality will not improve even if the S VHS ET function is used Check the recording quality before you start important recordings While playing back a tape recorded using the S VHS ET function on some recorders noise may appear If playback picture becomes blurred or interrupted use a cleaning cassette In the high speed search still slow motio
71. n or frame by frame playback modes C pg 16 noise may appear If these modes are performed frequently on a tape recorded using the S VHS ET function the tape may be damaged and the picture may be deteriorated RECORDING cont Receiving Stereo and Bilingual Programmes Your recorder is equipped with a Sound Multiplex decoder A2 and a Digital stereo sound decoder NICAM making reception of stereo and bilingual broadcasts possible When the channel is changed the type of broadcast being received will be displayed on the TV screen for a few seconds Type of Broadcast Being On screen Display Received A2 Stereo ST A2 Bilingual BIL Regular Monaural none NICAM Stereo ST NICAM NICAM Bilingual BIL NICAM NICAM Monaural NICAM To listen to a stereo programme press AUDIO on the remote control until HIFI L R appears on the TV screen To listen to a bilingual programme press AUDIO on the remote control until HIFI L 02 or HIFI appears on the TV screen To listen to the standard Regular Monaural audio while receiving a NICAM broadcast press AUDIO on the remote control until NORM appears on the TV screen NOTE O S D PLAY must be set to ON or the on screen displays will not appear F pg 46 When you change the setting in stop mode set O S D REC to ON pg 45 first Then set O S D REC to OFF if you do not want to record the opera
72. n screen you can skip or add channel positions enter station names and perform other operations Refer to pages 52 54 for the procedures Depending on reception conditions the stations may not be stored in order and the station names may not be stored correctly 52 Manual Channel Set Store channels that were not stored during Auto Set Up C pg 12 or Auto Channel Set I pg 50 Hl Access the Main Menu screen Press MENU 2 Access the Confirmation screen Press AV to move the highlight bar pointer to MANUAL CH SET then press OK or The Confirmation screen appears Select the channel position Press AV until an open position in which you want to 01 25 ARD 08 C26 store a channel begins 02 C08 SKY1 09 55 WEST inki 03 10 ZDF 10 C24 blinking then press OK The 02 00 20 10 G23 OSE Manual Channel Set screen 05 C31 BBCI appears Example To store in position 12 PR CH ID PR CH ID 1 06 C32 BBC2 73 07 C33 3SAT 14 AY 4 EDIT X DELETE MENU EXIT The blueback screen and the programme currently being broadcast by the selected channel appear alternately for 8 seconds each SUBSIDIARY SETTINGS cont 4 Select the band Press AV to change the band between CH regular and CC cable then press gt PR CH 10 2 0 A SELECT 4 gt CURSOR lt gt 0K
73. nd Programme 4 overlap each other Hl Confirm the overlapping programmes Overlapping programmes blink on the TV screen 2 Select the programme to modify Press AV then press OK or D You can only select one of the overlapping programmes NOTE If you do not mind this overlap press PROG to finish the timer programme setting The programme with the lower programme number will be recorded and the other one will not be recorded correctly If no changes are made for approximately 1 minute the recorder will return to the normal screen Cancel or change programme setting To cancel a programme press X when the Programme screen you do not want is shown PROGRAM COMPLETED appears on the TV screen for about 5 seconds then the normal screen appears To change a programme press the appropriate button START DATE VPS PDC number key 7 DAILY number key 8 WEEKLY number key 9 and or SP LP EP when the Programme screen on which you want to make changes is shown then press OK PROGRAM COMPLETED appears on the TV screen for about 5 seconds then the normal screen appears NOTE If the overlap is not yet solved or another overlap occurs with the timer programme setting after making the last correction on a programme the conflicting programmes will be shown on the Programme Check screen again Repeat the above steps again until the overlap is solved
74. nect to a TV with S VIDEO AUDIO IN connectors Hl Connect the recorder to TV Connect the aerial recorder and TV as per RF Connection lt pg 10 Connect the recorder s S VIDEO OUT connector to the TV s S VIDEO IN connector Connect the recorder s AUDIO OUT connectors to the TV s AUDIO IN connectors gt Connect the recorder to mains Plug the end of the mains power cord into a mains outlet OUT IN S S VIDEO AUDIO OUT NOTES You can obtain high quality S VHS pictures If your TV is not stereo capable use the recorder s AUDIO OUT connectors to connect to an audio amplifier for Hi Fi stereo sound reproduction gt pg 43 To operate the recorder with your TV using the S VIDEO connection set your TV to its AV mode For switching the TV s mode refer to the instruction manual of your television After the connection is completed perform Auto Set Up on page 12 12 Auto Set Up Auto Channel Set Auto Clock Set Auto Guide Program Number Set INITIAL SETTINGS Before starting make sure of the following The TV aerial cable should be connected to the recorder The recorder s mains power cord should be connected to a mains outlet The TV should be set to its AV mode with AV or S VIDEO connection gt pg 10 11 UHF channel 36 wit
75. nectors on your stereo system s receiver or amplifier NOTE When listening to sound through the connected stereo system turn the TV s volume down completely 7 A renot O OUT IN S 1 SVIDEO Back of recorder AUDIO OUT CAUTIONS This recorder has a dynamic range of more than 80 dB with regards to its Hi Fi audio capability It is recommended that you check the maximum level if you are going to listen to the Hi Fi audio signals through a stereo amplifier A sudden surge in the input level to the speakers may damage them Some speakers and televisions are specially shielded to prevent television interference If both are of the non shielded type do not place the speakers adjacent to the TV set as this can adversely affect the video playback picture 44 Mode Set Turn on the TV and select the video channel or AV mode SUBSIDIARY SETTINGS You can change various mode settings on the Mode Set screen by following the procedure described below For each mode setting see pages 45 to 48 Hl Access the Main Menu screen Press MENU Access the Mode Set screen Press AV to move the MAIN MENU highlight bar pointer to PROGRAMME NAVIGATION MODE SET then press OK AUTO CH SET or gt MANUAL CH SET INITIAL SET AY GE MENU EXIT Select the mode Press AV t
76. ng a cassette whose record safety tab has been removed and REC SAFETY is set to ON c pg 48 Playback begins automatically You can use Navigation Playback I pg 37 but you cannot edit programme title or delete tape data pg 38 39 MENU AV Navigation Playback This function is useful when you wish to quickly find out what programmes you have recorded on a tape with this recorder This function allows you to select a programme to watch and then automatically searches for the start of the programme Load recorded cassette Insert a cassette recorded on this recorder Access the Main Menu screen Press MENU Access the Programme Navigation screen Press AV to move the highlight bar pointer to PROGRAMME NAVIGATION then press OK or If NO TAPE DATA DETECTED appears on the TV screen you cannot use the Navigation Playback function MAIN MENU Ly PROGRAMME NAVIGATION MODE SET AUTO CH SET MANUAL CH SET INITIAL SET Av MENU EXIT EN 27 Programme Navigation Screen 15 06 02 AY GK X DELETE 1 TITLE MENU EXIT Q Recording date Recording start time Q Station name After entering the programme title gt pg 38 programme title appears instead of the recording start time and station name Q Currently selected programme
77. o move the highlight bar pointer to the item you want to change MODE SET PREVIOUS PAGE PREVIOUS PAGE Lr DIGITAL TBC NR Lr AUTO SP LP TIMER Lz DAY TIME INSERT OFF T DIGITAL REC SAFETY ON PICTURE CONTROL POWER SAVE DAILY T RECORD NORM AUTO TIMER Hd STABILIZER 0 5 0 REC 0 5 0 PLAY COLOUR SYSTEM PROG NAVIGATION RETURN POINT NEXT PAGE NEXT PAGE AY GE Av GE AY GE MENU EXIT MENU EXIT MENU EXIT 4 Select the mode setting Press OK or D Return to the normal screen Press MENU ATTENTION e The setting you have made is kept in memory if the lithium battery is not exhausted Even if the recorder is unplugged or the power failure occurs it will resume every time you turn on the recorder t pg 14 You cannot change the mode settings on the Mode Set screen during recording gt pg 19 45 The default setting is bold in the table below m DIGITAL TBC NR ON OFF Your recorder is equipped with the Digital TBC Time Base Corrector that removes jitter from fluctuating video signals to deliver a stable picture even with old tapes and rental cassettes The on off of Digital 3 DNR Noise Reduction which cuts noise and enables clear picture reproduction is also linked to this function We recommend that you set DIGITAL TBC NR to ON when playing back a tape recorded on a camcorder playing back a tape repeatedly used
78. ode by pressing AUX number key 0 and or PR so that 1 1 or S 1 appears on the front display panel For details refer to the instruction manual of the satellite receiver Outdoor unit Aerial Audio video input connectors Back of TV Satellite cable TV aerial cable i ANT IN a Satellite receiver UJ AIA ad Af j Aerial d dh 7 connector T OUT n SVIDEO Back of recorder Mains outlet EN 43 Connecting Using A Stereo System These instructions enable you to connect your video recorder to your Hi Fi stereo system if you have one and listen to the soundtrack through the stereo FM tuner Television Speaker Speaker AUX IN or TAPE MONITOR Audio cable not provided Mains outlet Make connections Connect the AUDIO OUT L and R connectors on your video recorder to the AUX IN or TAPE MONITOR con
79. orto rt SER Reto he EORR 17 J Just Clock ze i 14 56 L Last Function Memory see 14 M Manual Channel Set 52 Manual Tracking sc 18 t REIS 17 20 MOd amp Set 44 N Next Function Memory sse 18 OSD c o tts 46 m M M 45 ON SCREEN DISPLAY 7 LIST OF TERMS P PICTURE CONTR ODL 45 PLAYBACK Ere E 15 Playback Resume FUNCTION 15 POWER SAME ERR RIS DIT 47 PROG NAVIGATION 46 PROGRAMME NAVIGATION 36 R REC SAFETY 48 Record One Programme While Watching Another 20 RECORDBING 5 ipi ied rper 19 Recording Resume Function eee 19 Repeat Playback s rede eet 18 Repeat Recording eis etre 21 RETURN POINT ie rea dee tee eeu e seis eoe tae erede tnn 48 5 Series Playback 52 25 ts tales 24 Series Recordihg 3e eter 26 SeEStations A rto deo tee e eme 54 Set Stations o Ii qne nep po 54 SHOWVIEW System Setup ssssssee 49 SHOWVIEW Timer Programming eene 28 Skip SeatClr deed te t ee ass 17 SOW MOON s ee eee re eR re aote be n vens 16 Soundtrack Selection sse 18 Still Picture Frame By Frame P
80. ound or fast forwarded Check the cassette PLAYBACK SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1 The playback picture does not appear while the tape is running If you are using the RF connection the TV receiver s channel selector is not set to the video channel the recorder s video channel has not been correctly set If you are using the AV or S VIDEO connection the TV receiver is not set to the AV mode If you are using the RF connection set the TV receiver to the video channel perform Video Channel Set C pg 58 If you are using the AV or S VIDEO connection set the TV to its AV mode 2 Noise appears during visual search This is normal 3 Noise appears during normal playback The automatic tracking mode is engaged Try manual tracking F pg 18 4 The playback picture is blurred or interrupted while TV broadcasts are clear or USE CLEANING CASSETTE message appears on the screen The video heads may be dirty Use a dry cleaning cassette TCL 2 or consult your JVC dealer 5 Breaks are noticeable in Hi Fi soundtrack The automatic tracking mode is engaged Try manual tracking F pg 18 60 RECORDING TROUBLESHOOTING cont SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1 Recording cannot be started There is no cassette loaded The loaded cassette has had its record
81. p time Press STOP to enter the time you want recording to stop Press and hold STOP to move in 30 minute increments or press and release repeatedly to move 1 minute at a time H Enter the programme date Press DATE The current date appears on the TV screen The date you enter appears in its place mnm Enter the channel position Press PR TP START STOP SP VPS PDC OFF DATE TV PROG 25 12 gt PROG EXIT N 2 Set the tape speed Press SP LP EP co It is not possible to select EP mode if COLOUR SYSTEM is set to MESECAM F pg 48 Set the VPS PDC mode Press VPS PDC number key 7 to select ON or OFF e If VPS PDC ON is displayed on the TV screen VPS PDC is set to ON e If VPS PDC OFF is displayed on the TV screen VPS PDC is set to OFF VPS PDC Recording in the right column 9 Access the Title Edit screen Press the number key 1 TM The Title Edit screen appears You can access the Title Edit screen only when PROG 4 NAVIGATION is set to ON pg 46 N 2 S 7 25 12 21 00 ARD 2 S 0 9 SELECT LETTERS X DELETE 4 gt 1 CURSOR lt gt 0K PROG EXIT Enter the programme title Press the number keys and gt to enter characters then press OK For details refer to Entering Character on page 39 0 9
82. pes e When B E S T is OFF PICTURE CONTROL switches automatically from AUTO to NORM AUTO TIMER ON OFF When this function is set to the timer is automatically engaged when the recorder power is turned off and automatically disengaged when the recorder is powered back on NOTE For safety when AUTO TIMER is set to OFF all other recorder functions are disabled while the Timer mode is engaged To disengage the timer press TIMER 0 5 0 REC ON OFF When this function is set to ON all the indicators displayed on the TV screen will be recorded If you do not want to record the indicators select OFF 46 EN SUBSIDIARY SETTINGS cont The default setting is bold in the table below m 0 5 0 PLAY ON OFF When this function is set to ON various operational indicators appear on the TV screen NOTES When you use this recorder as the source player for editing be sure to set O S D PLAY to OFF before starting e During playback the operation mode indicators may be disturbed depending on the type of tape being used m PROG NAVIGATION ON OFF When this function is set to ON the recorder stores information on the recorded programmes If you do not want to use the Programme Navigation function rx pg 36 set PROG NAVIGATION to OFF NOTES Programme Navigation is possible with the cassettes recor
83. received your recorder is not selected OR Set the Guide Program number for that station manually when you add a channel after Auto Set Up or Auto Channel Set has taken place When you wish to timer record a satellite programme with the SHOWVIEW system Set the Guide Program numbers for all satellite broadcasts received on your satellite receiver Turn on the TV and select the video channel or AV mode Guide Program Number Set Hl Access the Main Menu screen Press MENU Access the Initial Set screen Press AV to move the highlight bar pointer to INITIAL SET then press OK or gt Access the Guide Program Set screen Press AV to move the highlight bar pointer to GUIDE PROG SET then press OK or 4 Enter the Guide Program number Press AV or number keys to enter the Guide Program GUIDE PROG SET number for the desired station GUIDE PROG TV PROG as shown in the TV listings HEN Then press OK or gt aes Av MENU EXIT Example When inputting the Guide Program number 2 for ZDF H Enter the receiving channel position number Press AV or number keys to input the number of the GUIDE PROG SET recorder s channel position on GUIDE PROG TV PROG which the Guide Program EX number s broadcast is received by the recorder Then press OK or gt If the satellite broadcast is received on your recorder s auxil
84. rect however you are advised to keep Just Clock set to OFF SUBSIDIARY SETTINGS cont IMPORTANT If you performed Auto Set Up gt pg 12 without ever having set the clock previously the recorder s built in clock is also set automatically Perform the following steps only if Auto Clock Set has not been performed correctly by Auto Set Up OR the recorder s memory backup has expired OR you want to change Just Clock setting 7 the left column Just Clock in Hl Turn on the recorder Press 2 Access the Main Menu screen Press MENU Access the Initial Set screen Press AV to move the highlight bar pointer to INITIAL SET then press OK or gt 4 Access the Clock Set screen Press AV to move the highlight bar pointer to CLOCK SET then press OK or gt The Clock Set screen appears INITIAL SET CLOCK SET Lr CLOCK SET STIME DATE YEAR GUIDE PROG SET 0 00 01_01 02 JUST CLOCK OFF TV PR 1 7 Av MENU EXIT NOTE When you have selected MAGYARORSZ G CESK REPUBLIKA POLSKA or OTHER EASTERN EUROPE for the country setting pg 12 you cannot use Just Clock function Skip steps 6 and 7 on page 57 AY MENU EXIT EN D7 Set the date and time Press AY to set the time then press OK or gt The DATE display begins blin
85. renne CIO KSEE ERA Video Channel Set TROUBLESHOOTING QUESTIONS AND ANSWERS SPECIFICATIONS LIST OF TERMS LPT0720 001A EN 2 EN SAFETY FIRST Safety Precautions The rating plate and the safety caution are on the rear of the unit WARNING DANGEROUS VOLTAGE INSIDE WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE CAUTION When you are not using the recorder for a long period of time it is recommended that you disconnect the power cord from the mains outlet W Dangerous voltage inside Refer internal servicing to qualified service personnel To prevent electric shock or fire hazard remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial WARNING There are two different types of SECAM colour systems SECAM L used in FRANCE also called rois West and SECAM B used in Eastern European countries also called SECAM East This recorder can also receive SECAM B colour television signals for recording and playback Recordings made of SECAM B television signals produce monochrome pictures if played back on a video recorder of SECAM L standard or do not produce normal colour pictures if played back on a PAL video recorder with SECAM B system incorporated even if the TV set is SECAM compatible 3 SECAM L prerecorded cassettes or recordings made with a SECAM L video r
86. requirement 220 V 240 V 50 Hz 60 Hz Power consumption Power on 18 W Power off 3 6 W Operating 5 C to 40 C Storage 20 C to 60 Operating position Horizontal only Dimensions WxHxD 400 mm x 94 mm x 270 mm Weight 3 4 kg Format S VHS VHS PAL standard Maximum recording time SP 240 min with E 240 video cassette LP 480 min with E 240 video cassette EP 720 min with E 240 video cassette VIDEO AUDIO Signal system PAL type colour signal and CCIR monochrome signal 625 lines 50 fields DA4 Double Azimuth head helical scan system Signal to noise ratio 45 dB Horizontal resolution Recording system SP LP 250 lines VHS 400 lines S VHS EP 220 lines VHS 350 lines S VHS 70 Hz to 10 000 Hz Normal audio 20 Hz to 20 000 Hz Hi Fi audio RCA connectors VIDEO IN x 2 VIDEO OUT x 1 AUDIO IN x 2 AUDIO OUT x 1 S Video connectors IN x 2 OUT x 1 Frequency range Input Output en 63 TUNER TIMER TV channel storage capacity 99 positions AUX position Frequency synthesized tuner VHF 47 MHz 89 MHz 104 MHz 300 MHz 302 MHz 470 MHz UHF 470 MHz 862 MHz Aerial output UHF channels 22 69 Adjustable Memory backup time Approx 6 months Estimated figure based on provided fresh battery actual performance may differ Tuning system Channel coverage ACCESSORIES Provided accessories RF cable S video cab
87. rst cancel any unnecessary programmes 7 pg 33 Even if a power failure occurs the recorder keeps your timer programmes if the lithium battery is not exhausted Satellite Receiver Users To timer record a satellite broadcast using the SHOWVIEW system 1 Set the Guide Program numbers for all satellite broadcasts received on your satellite receiver F pg 49 2 Perform steps 1 9 3 Set the satellite receiver to the appropriate channel before the selected programme begins Leave the satellite receiver s power on lt gt ATTENTION Guide Program Number Set GUIDE PROG SET appears after performing step 3 if the Guide Program number for the SHOWVIEW number you entered has not been set Press the number keys or AV to input the channel position number on which your recorder receives that station then press OK or gt to set the Guide Program number The SHOWVIEW Program screen appears GUIDE PROG SET Example To timer record a ZDF TV PROG programme with the Moz SHOWVIEW system If your recorder receives ZDF on the channel position 2 press OK or gt after entering 2 GUIDE PROG as Av PROG EXIT 30 n Express Timer Programming Before performing Express Timer Programming Make sure that the recorder s built in clock is set properly Insert a cassette with the safety tab in place If the tab has been removed set
88. s alternately as many times as you want You can select the returning point for Series Playback NOTE Use the buttons and controls on the recorder for the Series Playback operations except when using Mode Lock C pg 17 Hl Make connections Connect two sets of SR V10E and a TV using AV cables as illustrated on page 24 The mini plug cable is a mono 3 5 mm mini plug to mono 3 5 mm mini plug connector When playing back S VHS recordings it is recommended to use the S VIDEO connection to obtain the high quality pictures Turn on all components After completing the connections turn on all the components Set your TV to the VIDEO or AV mode Refer to the TV instruction manual Set the input mode on the SR V10E 2 Turn the JOG dial to the right or left on the SR V10E 2 to select the appropriate input mode depending on the connectors being used L 1 for the rear AUDIO VIDEO IN connectors F 1 for the front AUDIO VIDEO input connectors 1 for the rear AUDIO S VIDEO IN connectors 2 for the front AUDIO S VIDEO input connectors Un Load cassettes Insert the playback cassette into each SR V10E EN 25 H Start playback Press gt on either of SR V10E When the playback reaches to the returning point tape end or recording end CF pg 48 the other SR V10E successively starts playback The cassette will automatically be rewound when the playback stops Therefore
89. stable horizontal surface Connect the recorder to TV The connection method you use depends on the type of TV you have RF Connection connect to a TV with NO audio video input connectors 1 Disconnect the TV aerial cable from the TV 2 Connect the TV aerial cable to the ANT IN connector on the rear panel of the recorder 3 Connect the provided RF cable between the RF OUT connector on the rear panel of the recorder and the TV s aerial connector AV Connection To connect to a TV with audio video input connectors Connect the aerial recorder and TV as per RF Connection Connect the provided audio video cable between the AUDIO VIDEO OUT connectors on the rear panel of the recorder and the TV s audio video input connectors Un Connect the recorder to mains Plug the end of the mains power cord into a mains outlet After the connection is completed perform Auto Set Up on page 12 S VIDEO Connection Back of TV AUDIO IN connectors La T BA S VIDEO IN connector J Mains outlet Aerial connector Mains power cord S VIDEO OUT 1 S Video cable provided Audio cable TV aerial cable not provided iii Back of recorder RF cable provided To con
90. stations have been stored in the recorder s memory by using the PR button s If station names ID gt pg 55 have also been stored in the recorder s memory the station name will be displayed at the upper left corner of the TV screen for about 5 seconds when the recorder is tuned to a different station If you want to set the tuner manually such as to add or skip channels to change channel positions or to set or change station names see pages 52 55 INN A E LFLIL If Auto Channel Set has succeeded but Auto Clock Set has not 1 channel position is B displayed 1 Turn on the TV and select its video channel or AV mode then make sure that all necessary stations have been stored in the recorder s memory by using the PR button s If station names ID CF pg 55 have also been stored in the recorder s memory the station name will be displayed at the upper left corner of the TV screen for about 5 seconds when the recorder is tuned to a different station If you want to set the tuner manually such as to add or skip channels to change channel positions or to set or change station names see pages 52 55 Perform Clock Set on page 56 If both Auto Channel Set and Auto Clock Set have failed is displayed i Make sure the cables are connected properly and turn off the re
91. tapes can be stored You can also enter the programme title when performing SHOWVIEW Timer Programming CF pg 28 or Express Timer Programming I pg 30 It is possible to store these information only when PROG NAVIGATION is set to ON default setting C pg 46 Turn on the TV and select the video channel or AV mode When inserting a cassette with the record safety tab intact or when inserting a cassette with a record safety tab removed and REC SAFETY is set to OFF F pg 48 The recorder checks the tape information for the Programme Navigation If the recorder can store the information for 3 or less tapes REMAIN also appears on the TV screen CHECKING TAPE DATA REMAIN 3 If the recorder has already stored the information for 10 tapes MEMORY FULL appears If you perform new recording the oldest tape information will be deleted from the recorder s memory CHECKING TAPE DATA MEMORY FULL If the recorder cannot detect the tape information DATA DETECTED appears NO TAPE DATA DETECTED NOTES If you press any button while CHECKING TAPE DATA appears on the TV screen the operation is canceled Even if the recorder has already stored the information for 8 programmes on one cassette no message appears If you perform new recording the oldest information will be deleted from the recorder s memory When inserti
92. the AUTO mode does not function properly select the following manual mode PAL NTSC record PAL signals or play back a PAL or NTSC tape MESECAM To record SECAM signals or play back a MESECAM tape NOTES It is not possible to record in S VHS if MESECAM is selected The recording mode is forced to change to VHS e If MESECAM is selected when the tape speed is set to EP mode the tape speed will be forced to change to LP mode It is not possible to select EP mode if MESECAM is selected About NTSC Playback Some TVs shrink the picture vertically and place black bars at the top and bottom of the TV screen This is not a malfunction on the part of either the video recorder or the TV The picture may roll up and down This can be corrected using the V HOLD control found on some TVs This cannot be corrected if the TV does not have a V HOLD control The counter and tape remaining time readings will be incorrect e During search still or frame by frame playback the picture will be distorted and there may be a loss of colour Depending on the type of TV the top and bottom portions of superimposed displays may be cut off during NTSC playback RETURN POINT TAPE END REC END Returning point for Playback Repeat Playback or Series Playback can be set to tape end or recording end This recorder considers 1 second unrecorded portion as the recording end When the returning point is reached p
93. the cassettes loaded on two SR V10E will be played back alternately as many times as you want mnm Stop playback Press on the SR V10E which is playing back a cassette NOTES If you do not want to display the operational indicators on the TV screen during playback set O S D PLAY and O S D REC to OFF pg 45 46 If there is a power outage during Series Playback the playback will resume automatically when the power is restored to the recorder if the lithium battery is not exhausted It is possible to use the Mode Lock function pg 17 2 6 EN SERIES PLAYBACK AND RECORDING cont Series Recording Camcorder or Another recorder To S video To Audio video output output connectors connectors Audio video cable not provided gt S video cable not provided AUDIO VIDEO OUT SR V10E 1 a y S VIDEO OUT SVIDEO IN M E Ll REMOTE IN AUDIO VIDEO IN L u Mini plug cable S video cable a Mini plug cable not provided provided not provided Audio video cable provided AUDIO VIDEO OUT S VIDEON f REMOTE OUT SR V10E 2 AUDIO VIDEO IN S VIDEO OUT i To S video input connectors Se S video cable not provided REMOTE IN
94. tional indicators displayed on the TV screen To Record Stereo and Bilingual Programmes A2 Stereo programmes are automatically recorded in stereo on the Hi Fi audio track with the normal audio track recording mixed L and R channel sound e Bilingual programmes are automatically recorded in bilingual on the Hi Fi audio track The main soundtrack will be recorded on the normal audio track To Record NICAM Stereo and Bilingual Programmes The NICAM audio programme will be recorded on the Hi Fi audio track and the standard audio programme will be recorded on the normal audio track NOTES e If the quality of stereo sound being received is poor the broadcast will be received in monaural with better quality Before playing back a programme recorded in stereo or a bilingual programme refer to Soundtrack Selection on page 18 D E S T Picture System The B E S T Biconditional Equalised Signal Tracking system checks the condition of the tape in use during playback and recording and compensates to provide the highest possible playback and recording pictures You can set B E S T to ON or OFF to your preference 45 Playback The recorder assesses the quality of the tape once you initiate playback S gt IL JIL 2 N The recorder adjusts the playback picture quality based on the quality of the tape in use B E S T is active during automatic trac
95. to enter characters then press OK For details refer to Entering Character on page 39 0 9 SELECT LETTERS X DELETE 4 gt 1 CURSOR OK PROG EXIT Return to the normal screen Press PROG or OK PROGRAM COMPLETED appears on the TV screen for about 5 seconds then the normal screen appears If PROGRAM OVERLAPPED appears on the TV screen and Err on the front display panel see page 34 Repeat steps 1 8 for each additional programme 9 Engage the recorder s timer mode Press TIMER The recorder turns off automatically and appears on the front display panel To disengage the timer mode press TIMER again EN 29 NOTES To Change The Stop Time press STOP after pressing OK in step 3 You can compensate for anticipated programme schedule delays Timer Record Weekly Or Daily Serials after pressing OK in step 3 press WEEKLY number key 9 for weekly serials or DAILY number key 8 for daily serials Sunday Saturday Either WEEKLY or DAILY appears on the TV screen Pressing the button again makes the corresponding indication disappear You can programme this recorder to timer record as many as 8 programmes If you try to programme the recorder to record a ninth PROGRAM FULL appears on the TV screen and FULL appears on the front display panel To record the extra programme you must fi
96. ton gt pg 21 DAILY Button x pg 29 31 WEEKLY Button gt pg 29 31 AUX Button c pg 40 Timer Button gt pg 29 31 DATE Button gt pg 30 PR Button c pg 19 Auto Tracking ZZ Button gt pg 18 SP LP EP Button gt pg 19 30 SEC Button gt pg 17 Play Button gt pg 15 Fast Forward gt Button c pg 15 16 Pause Button gt pg 16 OK Button gt pg 13 Information 9 Button If you press this button when O S D PLAY is set to ON C pg 46 you can see the current recorder status on the TV screen lt i gt Button c pg 16 17 TV 21 Button gt Operating JVC TVs on page 9 EN 9 Buttons with small dot on the left side of the name can also be used to operate your JVC TV while holding down the TV button c Operating JVC TVs below This remote control transmits A code signals only it is not applicable to B code signals How To Use The remote control can operate most of your video recorder s functions as well as basic functions of JVC TV sets 7 Operating JVC TVs below Point the remote control toward the receiving window The maximum operating distance of the remote control is about 8 m Operating JVC TVs To operate your TV while holding down the TV button press the corresponding button 071 TV VCR TV PR TV _1 01 TV Muting NOTES When inserting the ba
97. tteries be sure to insert in the correct directions as indicated under the battery cover Depending on the type of JVC TV some or all functions may not be operated using the remote control If the remote control doesn t work properly remove its batteries wait a short time replace the batteries and then try again I0 Basic Connections Aerial connector Back of TV RF cable provided Audio video input DUE connectors Audio video cable provided Mains power cord T oy y tg ANT IN Back of recorder AUDIO VIDEO OUT RF OUT Mains outlet Make AV connection if your TV has audio video input connectors in order to reduce the possibility of interference With AV connection you can enjoy stereo playback of video tapes if you are using a stereo NOTES For switching the TV s mode refer to the instruction manual of your television To obtain high quality S VHS pictures you can also use the S VIDEO connection described on page 11 INSTALLING YOUR NEW RECORDER It s essential that your video recorder be properly connected THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED Hl Check the contents Make sure the package contains all of the accessories listed in SPECIFICATIONS on page 63 2 Situate the recorder Place the recorder on a
98. tting while tape speed is displayed Kl Engage the recorder s timer mode Press 24H EXPRESS The recorder turns off automatically and O appears on the front display panel To disengage the timer mode press TIMER or 24H EXPRESS again EN 23 To cancel or change a programme 4 Cancel or change a programme Press X to cancel a programme To change programme settings press the appropriate button START STOP PR VPS PDC number key 7 DAILY number key 8 WEEKLY number key 9 and or SP LP EP If you do not want to edit the programme title skip steps 5 and 6 Access the Title Edit screen Press the number key 1 m The Title Edit screen appears EN You can access the title edit 24 12 ST WDR 7 27 b screen only when PROC 2 NAVIGATION is set to ON pg 46 0 9 SELECT LETTERS X DELETE 4 gt CURSOR lt gt 0K 1021 EXIT Check cancel and change programmes Enter te programme title Press the number keys and gt 1 Disengage the timer mode to enter characters then press OK For details refer to Entering Character on page 39 2 Access the Programme Check screen display 0 9 SELECT LETTERS X DELETE Press TIMER then press CURSOR Press f OK 99 EXIT 2 3
99. y cables can be obtained from your dealer When you select EDIT to dub tapes in step 3 be sure to select AUTO or NORM when B E S T is set to OFF after you finish dubbing the tapes When you use this recorder as the recording deck for editing set O S D PLAY and O S D REC to OFF F pg 45 46 if you do not want to record the operational indicators displayed on the TV screen It is also possible to use the rear AUDIO VIDEO IN or AUDIO S VIDEO IN connectors for the connection When you use the rear connectors select L 1 for the AUDIO VIDEO IN connectors 5 1 for the AUDIO S VIDEO IN connectors step 2 Edit To Or From Another Video Recorder TV receiver Player Your recorder dh dh S video cable ZG ME E Audio video cable I LI 1 1 Audio video cable e Video Go channel or AV mode Another recorder ee Recorder 2 Recorder Your recorder TV receiver S video cable Audio video cable O m eco Video channel or AV mode Another recorder I Advantages of S VHS video recorders You can edit fro
100. y depending on the reception condition 598 EN Video Channel Set SUBSIDIARY SETTINGS cont Video channel RF output channel is the channel on which your TV receives picture and sound signals from the recorder through the RF cable IMPORTANT Perform the following steps only if area Video Channel Set has not been done correctly by the Auto Set Up function F pg 12 interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your you change the connection between your recorder and TV from RF connection to AV or S VIDEO connection or vice versa If you have connected the recorder to your TV via the AV or S VIDEO connection pg 10 11 since you do not need the video channel you have to set the video channel to off If you have connected the recorder to your TV via the RF connection lt pg 10 you have to set the correct video channel Before performing the following steps Make sure the recorder s power is off and there is no cassette inserted in the recorder Hl Access the Video Channel Set mode Hold down W 4 on the recorder until the front display panel shows the following 2 mM ahs n Set the RF output system The blinking number on the display indicates the RF output system of your country If you have selected MAGYARORSZAG CESKA RE
101. y of approximately 7 seconds after on the remote control are pressed or on the recorder is pressed To make sure you record the desired scene or programme in its entirety first perform the following steps Press and hold and press to engage the Record Pause mode The recorder then automatically checks the condition of the tape and after approximately 7 seconds re enters Record Pause mode 2 Press B to start recording If you want to bypass the B E S T system and begin recording immediately set B E S T to OFF I pg 45 2 4 SERIES PLAYBACK AND RECORDING Series Playback REMOTE OUT DO 2 Mini plug cable not provided SR V10E 1 S VIDEO OUT AUDIO VIDEO OUT S video cable Mini plug cable provided not provided Audio video cable provided S VIDEO IN REMOTE OUT AUDIO VIDEO OUT SR V10E 2 S VIDEO OUT AUDIO VIDEO IN S video cable not provided REMOTE IN eee eee eee eee eee Audio video cable not provided To S video input connectors To Audio video input connectors NOTE Series Playback is also possible with the front AUDIO VIDEO or AUDIO S VIDEO input connectors Using two sets of SR V10E you can play back two cassette

Download Pdf Manuals

Related Search

Related Contents

GBC 3400935EZ lamination film  

Copyright © All rights reserved. Failed to retrieve file