JVC SP-F508 User's Manual
Contents
1. Base plates 2 EN 3 Take out the speakers with its protections at top and bottom then stand them upright with top side down Do not to touch the speaker units to prevent damage Take care that speakers do not fall over JVC SP F508 4 Remove the bottom protection Take care that speakers do not fall over 5 Lift up the speakers to remove the top protection by pressing it down then place the speakers on the cloth Take care that speakers do not fall over LV44076 001A UJ2. MM JVC SP F508 SPEAKER SYSTEM INSTRUCTIONS LVT1278 001A UJ Thank you for purchasing a JVC speaker system Before you begin using these speakers please read the instructions carefully to be sure you get the best possible performance If you have any questions consult your JVC dealer Warnings Cautions and Others W Precautions for installation W Precautions for daily use e Do not install the speakers on an uneven surface or in a place To maintain the appearance of the speakers subject to vibration otherwise they may fall over causing damage or injury Take the occurrence of earthquakes or other physical shocks into consideration when selecting the installation place and secure the speakers thoroughly e To prevent deformation or discoloration of the cabinet do not install the speakers where they are exposed to direct sunlight or high humidity and avoid installation near air conditioning outlets Wipe with a dry soft cloth if the cabinet should become dirty If very dirty apply a small amount of water or neutral detergent to the cloth and wipe clean then wipe with a dry cloth e To improve the sound field It is recommended to leave a space of more than 50 cm between the speakers and the wall f the speakers are facing a solid wall or glass door etc it is recommended to furnish the wall with materials that absorb sounds for example by hanging up thick
3. curtains to prevent reflections an ndin Speaker vibrations may cause howling Place the eflections and standing waves speakers as far away from the player as possible To use the speakers without any trouble Do not reproduce sounds at so high a volume that they are distorted otherwise the speakers may be damaged by internal heat buildup When moving the speakers do not pull the speaker cords otherwise the speakers may fall over causing damage or injury e The speakers are magnetically shielded to avoid color distortions on TVs However if not installed properly it may cause color distortions So pay attention to the following when installing the speakers When placing the speakers near a TV set turn off the TV s main power switch or unplug it before installing the speakers a a ome i nee W Checking the supplied accessories Some TVs may still be affected even though you have followed Base plates 2 the above If this happens move the speakers further away Speaker grilles 2 from the TV Speaker cords 4 m 2 e Tuner reception may become noisy or hissing if a speaker is Screws M4 x 20 mm 8 installed near the tuner In this case leave more distance If any item is missing contact your dealer immediately between the tuner and the speakers or use an outdoor antenna for better tuner reception without interference from the speakers e Do not lean against the speakers as the speake
4. maged e The impedance of the speaker is 6 Q Before connecting it to your amplifier check the speaker impedance range of your amplifier If the impedance of this speaker is out of the speaker impedance range indicated on the amplifier you cannot connect this system to the amplifier e The maximum power handling capacity of the SP F508 is 100 W Excessive input will result in abnormal noise and possible damage e Be sure to turn down the volume level to prevent unwanted noise before performing following operations Turning on or off other components Operating the amplifier Tuning FM stations Fast forwarding a tape Continuously reproducing high frequency oscillation or high pitch electronic sounds e When using a microphone do not aim it at the speakers or use it near the speakers otherwise the howling which occurs may damage the speakers e Before replacing the cartridge always turn off the power to the turntable otherwise the clicking noise may damage the speakers e Speaker cords are supplied to the speakers When using other speaker cords observe the following Buy thick speaker cords rather than thin cords and make them as short as possible for connection Use speaker cords of the same length for both left and right speakers Do not use long speaker cords otherwise the sound quality may deteriorate Using a special speaker cord such as a litz wire a coaxial cable o
5. r a cord which has the specified connecting directionality may influence the sound quality W Connecting the speaker cord Connect the speaker cord to the speaker as illustrated e Make sure to match the polarity 4 and otherwise the surround effect will become less effective Before connecting Twist and remove the insulation at the end of each speaker cord 2 Insert 3 Release Speaker terminals on the amplifier RIGHT LEFT Right speaker Left speaker Specifications Type 2 way 3 speaker bass reflex type Magnetically shielded type Speakers Woofer 10 0 cm cone x 2 Tweeter 4 0 cm cone x 1 Power handling capacity 100 W Impedance 6 Q Frequency range 55 Hz to 20 000 Hz Sound pressure level 85 dB Wem Dimensions W x H x D 250 mm x 1065 5 mm x 310 mm Mass 7 2 kg Design and specifications subject to change without notice 2 en 2004 Victor Company of Japan Limited 0704NSMMDWHCE Unpacking the speakers Precautions for unpacking e Have two persons unpack for safe unpacking and installation e Place a large thick cloth on the floor where you unpack the speakers so you can protect the floor and the speakers themselves 1 Take out the packing pad with speaker cords and screws on the top Speaker cords and screws 2 Take out the speaker grilles and base plates e Refer to Instruction about how to attach speaker grilles and base plates Speaker grilles
6. rs could fall down or break possibly causing an injury Especially be careful that children do not lean against them Preparation W Attaching the base plate W To remove the speaker grille To prevent the speaker from falling over be sure to attach the To remove the speaker grille insert your fingers at the bottom supplied base plate to each speaker of the speaker grille then pull upward e Take care not to drop the base plate or speaker while assembling otherwise it may cause damage to the floor or injury e Ensure enough space for assembly and installation e Place a large thick cloth on the floor where you assemble the speaker so you can protect the floor and the speaker itself e Do not touch the speaker units Turn the speaker upside down and attach the base plate securely on the bottom of the speaker with the supplied screws as illustrated e Prepare a Phillips screw driver e Make sure that the FRONT arrow on the top of the base plate points the front side of the speaker Screw M4 x 20 mm Base plate ae supplied Speaker Front side To attach the speaker grille put the projections of the speaker into the holes of the speaker grille e Do not press the speaker grille strongly Speaker units W Connecting the speaker system to the amplifier Before connection e Turn off the power to the amplifier before connecting the speaker system otherwise the speakers may be da
Download Pdf Manuals
Related Search